I'm planning to flash my E4200 to WRT-DD to enable VPN feature in my house. Typically in my college dorms all ports are closed beside 80 and 443. From what I understand from VPN is that you can connect directly to it and operate in a network as if you are working inside that VPN's network. Do I understand this correctly (So I can have all ports open)? Anyways, will I be able to connect to my router's VPN while being in the college dorm having only port 80 and 443 open?
I connect to my corporate network using Cisco AnyConnect Secure Mobility Client. Once connected I can no longer print to my LAN attached printer and other local resources. I use the Cisco/Lyncsys E4200 router on my LAN and can re-connect to the storage on the local LAN by setting up Port Forwarding of port 21 and MS Windows FTP folder sharing. However, I can't seem to connect to a Terminal Services client by forwarding port 3389. Is there a way to connect to the local LAN after logging into the VPN connection. I can connect to regular HTTP/HTTPS sites and most other type of connectiins, just not my own local resources.
I've had for several years very good experience with the WRT54GL. Based on that experience I upgraded to a e4200.But so far it's not living up to my expectations (media server not probably working with external harddisk, no advanced logging of incoming/outgoing traffic, connection problems) and I'm getting pretty frustrated with it.Problem right now is that one of my laptops with Windows 7 is often not connecting correctly to the wireless network of the e4200. It's giving a "unidentified network" error. Rebooting computer and router is not working. The computer is (always) reliable connecting to another wireless network in my home. It seems the DHCP is not working properly?
Have a Linksys E4200 router located in my basement and I am experiencing a puzzling wired connectivity issue as follows: Port 1 on the router is for my study, I have no problem getting connection regardless if I use my study's Ethernet jack or if I run a 5 ft. cable (hereinafter THE CABLE) from the router’s port 1 to my laptop (i.e., cabling does not make a difference).I then connect to router port 1 an EZXS55W Linksys switch (using port 1 on the switch and THE CABLE) and then connect my laptop to port 2 on the switch using a second cable. I am unable to connect to the network/internet even after rebooting both the cable modem and router.I then reconnect my study to port 1 on the router, I go to my study and connect the study’s Ethernet jack using THE CABLE to port 1 on the switch and using a second cable from port 2 on the switch to my laptop. …. I get an network/internet connection immediately ! FYI, I have had the exact problem with switches EZXS88W and SE2500 (no longer own this).
i purchased an E4200 router to replace my old WRT150N. I had a WUSB300N that connected fine to the old router, but it's not connecting to the E4200. I have a guest network set up on it, and the adapter can connect to that, so I'm at a loss as for why it won't connect. Does anyone think it has something to do with the type of security I have set up? I had it on WPA2 on my WRT150N, and the E4200 on WPA2/WPA mixed mode.
I've been messing around with this for several weeks to no avail. I've never had a problem establishing a VPN connection within my LAN. I've tried several workarounds, learning things in the processs, but to no avail.I've set up a VPN connection with Windows 7. The RRAS server is at home and I'm attempting to access from school (or the internet anywhere).I have no problem establishing the VPN connection (that I can see). Port 1723 is forwarded for both UDP and TCP to a static LAN address (198.162.1.124) in the E4200. PPTP pass-through is enabled (as well as the other two options).I can't see anything on the server after connecting. I'm using a DDNS. It works just fine INSIDE the LAN; I've even mapped a network drive to "S:". Accessing ANYTHING outside of the LAN over a VPN, however, isn't working. [code]
I have an issue with a brand new E4200 router. My E4200 can connect no issue with the following devices: Ipad, AppleTV, Dell Laptop, Ibm Laptop. It is also wired connected to my home PC. Internet works fine and file sharing/network works good for all the above devices.
The problem is that My wife and I's Phone can not detect the wifi network and can not connect to it. The SSID broadcast is enabled on both frequencies (2.4 and 5). I have try configuring the network manually on both the Android phones..it does not work.. it records the data but keep sayng the network is out of range (although I'm right next to the router). I hva eplayed with various channels on both frequecies and played also with the MTU size.One of the Android phone is Garmin the other Acer Liquid...different brand running both Android 2.2...
Firmware on E4200 is 1.0.02 All settings reset to Auto/MIxed for now. WPA2 is enable with security key SSID is enabled on both frequency no MAC address filtering is setup
Both my phones can detect other networks and can connect fine to friends and family networks...So I suspect a compatibility problem between router an Android..I have contacted Linksys support twice with no avail. I have contacted both Acer and Garmin...they refer me to linksys
I am trying to replace my Cradlepoint MBR1200 with a CBR450 in bridge mode, to let the E4200 take over all the WAP and DHCP handling, but having a hard time.I set the CBR450 in bridge mode and when I connect it to my laptop it properly passes the IP info to my Mac and allows me to connect. I then connect it to the E4200 WAN port with it set to get IP address automatically but nothing ever happens and I am never allowed traffic in/out over the WAN.
I *can* get internet access by leaving the CBR450 in normal mode (handling DHCP, etc) and then plugging it into the E4200 LAN port and having the E4200 set to bridge.why the E4200 WAN port is not getting the bridge info and allowing connection? FWIW, works fine connecting to a DSL modem with the DSL model set to bridge mode at my other house.
Have the issue of connecting a pc an NAS to a E4200 and when transferring from pc to NAS, only getting < 10 mbps transfer rates? NAS is Dlink 321. PC has Gigabit ethernet card. cables are cat 6. Even when I force the NAS and pc network card speeds to 1.0 GBps full duplex, I only transfer files at < 10 Mbps.
I purchased a WAG320N and E4200 and have manged to get the modem connected to the internet and it's running fine in that respect, with no adjusting done to the settings.My intentions are to connect the WAG320N to the E4200 wirelessly, as they are in seperate rooms in the house and have done a similar setup in the past with a 7300G Billion Modem and WRT54GL.
With the E4200 I quickly discovered there was no bridge mode out of the box, but checking these forums got the indication that the firmware updates added this capability, so updated it..I entered the IP Address of the Router, the Subnet mask of the network and the Default Gateway / Modem router IP address into the fields, following this guide, but have not been able to get the computers to contact one another, nor ping the other devices.
I have an E4200 wireless router which is connected via USB to my Canon MX 308 printer. I am able to print from Windows computers that are connected to this router (via WiFi of course). My iPad 2.0 is able to connect to the internet via the router. However I am not able to print content from my iPad via the E4200 router (via Wifi using Cisco Connect software).
I'm trying to connect the D-Link 930L Wireless N Camera to my E4200 router. When I have the camera connected via the Ethernet cable it works fine, as soon as I unplug the Ethernet cable it will not connect wirelessly. I tested the camera on a friends router E3000 and the camera connects fine and work flawlessly on his network wirelessly. Any settings in the router that need to changed or set differently?? All of my other devices work great. I have been through D-Links Tech support all things point back to my router.
I have a new E4200 with the latest firmware and my slingbox seems to not be playing nice with the router. It refuses to take the IP I reserved for the SB, but always defaults to 192.168.2.254. I use a 2 subnet just in case you're wondering. I have tried multiple reboots and the IP does not change. I have tried turning off UPNP, figuring that was hijacking the dhcp server, but that hasn't changed anything. I also notice that a few of my connected devices do not show up in the dhcp list, yet they connect and work ok.
I was attempting to use my EA4200 in bridge mode but found out for some reason my devices weren't connecting to the internet. So I decided to try to access the router through the IP address of the router with no avail. So I pull the router and plug it in normally and notice that it keeps flashing. So that already gives me an idea something is wrong. I go through the process of unplugging everything from the router, and plugging my PC directly into the LAN port 1 of the router then powering it up. On my network connection list it keeps trying to identify the network but keeps failing (keep in mind that the router still is flashing). So I decide to attempt a 10 second reset, then a 30 second, then a 30-30-30. All with no success. The router keeps flashing.
Which gets me to the point where I am now... router flashing at me, and wondering if this now out of warrenty unit was a waste of money. I am noticing that a lot of people have had questions and issues with the E4200v2 which now concerns me, well hopefully this can be fixed.
Last week I purchased the E4200 and for simplicity, I configured it with basic settings using Cisco Connect. Today, I went into the web interface. The only thing I did was review settings and get the Routers PIN (it appears that Intel Chipset cards on Windows requires this PIN?) Close the browser (did not save any settings) and now I am completely locked out of the device. Cannot connect does not accept the wireless password. I hard reset the device, ran through the wizard. Everything was working again. Launch the browser and connected to the device closing window and balm?
I am trying to configure the firewall of a linksys 4200. I would like to be able to close or open every single port on protocols/incoming/outgoing. There doesn't seem to be a straightforward way in the e4200 web interface, is there any other way to perform this? Google doesn't seem to provide me many alternatives.
I am using a Cisco E4200 router today but I am moving to a ASA5505. I have a device that sets up a VPN tunnel that I want to put in my DMZ. It's called the ATT Gateway. I have attached the diagram. When I use a Cisco E4200 all I do is put the outside private ip address of 192.168.0.99 of the ATT Gateway into the DMZ of the E4200 and the VPN tunnel of the ATT Gateway comes right up. I cannot configure the DMZ to do the same with the ASA. I also need to have the laptop behind the gateway access the printers in the inside network.
I changed from a Linksys E4200 to a 5505 and when I use trace route, it doesn't return a DNS name for each hop. I can see the hops shown as asterisks. Do I have to add something to inspect for this to work?
I'm using the Cisco ASA 5520 on GNS3 .. Everything is working fine, except for one thing. The CCP .. I tried the CCP with a router and it worked, but it can't see the firewall.
I have already enabled the HTTP server using "HTTP server enable" and created account using "username admin privilege 15 password admin" also enabled SSH and Telnet on the ASA
"ssh 0 0 INSIDE" "telnet 0 0 INSIDE"
When I use the CMD to telnet to the ASA, it works just fine .. Also, when I connected a router to the ASA I could SSH to it, as well as using the PuTTy . Is there a way to troubleshoot? Or even a document that illustrates how to configure the ASA for CCP? Better a document for configuring the ASA from scratch .
I set up a cisco 2811 to replace a netgear router at the office. I have nat set up and with ccp I added a firewall on the router using the basic firewall wizard. Just about everything works internet, receiving and sending emails on exchange from the pc. Issue I'm having noone can access the company email on their phone.Also theres a camera system that would be accessible to view from the live feed from outside the office and my boss can't access the camera. I port mapped all the custom applications and added new traffic rule from self -> outzone. It didn't work tried to add one from outzone -> self or inzone but i get a prompt stating it only accepts protocols tcp,udp, sip, h323, icmp and a few other I can't think of. I'm pulling out my hair trying to get this to work everything worked seamlessly on the netgear router and nothing was really defined just the inbound ip address of the applications and protocols that are allowed.
Lets say for reference purposes my ip addresses for internet is
internet 55.34.23.43 /24 email server 192.168.10.252 /24 web cam application 192.168.10.10 /24 8000 in 8001 out
ASA design. I have two Cisco ASA 5585 which are connecting to two Nexus 7K. I looked at one design and it seems I can make Redundant interfaces on ASA and put two physical interfaces (Link1-1/1-2) into it however the down side I can see is it will utilize one link out of 4 at one time. As per my understanding if I make redundant interface on ASA 1 and put 1-1/1-2 into it only one link would be active at one time. This will force Nexus2 to send all traffic to Nexus 1 in order to reach ASA. Ideally I want a solution where both switches could send traffic straight to Active Firewall and incase of failure both links to standby firewall.
We currently have 2 different ASA 5505 connect to our ASA5510. We want to VPN connect the 2 5505's to each other while still mantaining connection to our 5520. I have attached pdf of what we have. What we want is to connect traffic between the two 5505's so that devices in either location can talk to each other while still mantainig connection to the 5510.
We recently changed locations and acquired a new circuit from our provider. They also connected our remote branch office to our main office through MPLS. Now, as I understand it, the branch office basically connects back to the main office through our providers network (MPLS). We have a new router at the branch office which has a gateway of 192.168.1.225. The clients in that office have IP's of 192.168.1.96 - 100, using the gateway of 192.168.1.225.
The main office network is 192.168.0.0 (Gateway of 192.168.0.1)
At this end (Main office), I also have a new Cisco 2900 provided by the ISP, with port 0/0 for the outside connection (connected to the 0 port on my ASA 5505). The ASA's port 1 obviously running into my network hub. The provider tells me that port 0/1 on the 2900 is or should be used to connect the branch office back to here and has an IP of 192.168.0.225, as that's how the provider provisioned it. So, I plug that into the ASA's Ethernet port 0/2. And I'm assuming they have a route setup either on the 2900 or the router in the branch office so that 192.168.1.225 can reach me here at 192.168.0.0.
There is already a static route setup on the ASA: (192.168.1.0 255.255.255.255 192.168.0.225 1). As soon as I plug in the cable, the IP phones at the branch office work, but they can't access the internet or any resources in the main office. My questions are:
1. Shouldn't I be able to just go straight from the 0/1 port on the Cisco 2900 to my hub. At first I was plugging right into the ASA, but I don't think I need to do that, why go from the branch office through my ASA to access resources and then back out the ASA for internet. If they're already coming from 192.168.1.225, through the MPLS network, then they should go right to my network and then back out the ASA.
2. They have to route through the ASA first, in which case, do I need to setup another VLAN for that branch network in conjunction with a static route? I can ping the router and hosts in the branch office through the ASA only!
We currently have 2 different ASA 5505 connect to our ASA5510. We want to VPN connect the 2 5505's to each other while still mantaining connection to our 5520. I have attached pdf of what we have. What we want is to connect traffic between the two 5505's so that devices in either location can talk to each other while still mantainig connection to the 5510.
I have two ASA5510 with a peer to peer VPN configuration which is working pretty well.I'm trying to connect to my remote ASA (ASA2) with ASDM on my PC through the VPN on the local ASA (ASA1)I already connected the ASDM to ASA1 through the inside interface but I cant connect to the ASA2 the same way (over the VPN).
When I ping the ASA2 inside interface from my computer, I get the following events:
ASA Version 8.0(5)!hostname ciscosnqdomain-name chaco.com.boenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednamesname 192.168.2.10 SNQ-Servername 192.168.1.21 Srvplxaname 10.30.30.30 e-Servername 192.168.1.0 Experion-networkdns-guard!interface Ethernet0/0 nameif Corporativo security-level 0 ip address 10.64.12.6 255.255.0.0!interface Ethernet0/1 nameif ExP_LS security-level 90 ip address 192.168.2.1 255.255.255.0!interface Ethernet0/2 shutdown no nameif no security-level no ip address!interface Ethernet0/3 shutdown no nameif no security-level no ip address!interface Management0/0 nameif management security-level 100 ip address 192.168.0.2 255.255.255.0!boot system
We are planning to purchase an ASA 5505 for a VPN solution for one of our offices. The office has 50-60 user at peak load who would be connecting over the S2S VPN to the datacenter.
From a hardware standpoint, can the ASA 5505 handle this load. The licence is for unlimitedf inside hosts but what is the actual limit on this platform?
Since several weeks ago we are triyng to solve a disconnection problem related to servers benind an ASA 5520 behind this ASA there are:
-subnet with public ip addres
-sunbet with prive ip address, the server on this subnet are acccesible via NAT.the problem is worst when some ousite our network and behind a nat device (like a adsl modem/router) tries to connect to those servers wich are using natted ip behind the ASA.I tried from my home to connect to this ASA5520 using annyconnect and get reset tcp packets. Are there some aditional configuration to make the ASA work properly?. We have other firewalls like PIX or software firewall (ASG), they work with no problem. Only the ASA 5520 has this issue.
Connecting ASA 5520 to two Catalyst 3560G layer 3 switches. What's the best practice to connect the asa-5520 at the edge, to the core of my network? What I'm looking to do is connect two routed gigabit ports (gi0/2 and gi03) to two seperate layer 3 routed ports on catalyst 3560G. I'm wondering how to do it, or if there's any type of failover method? I'm running EIGRP in the network and the link to the first core switch has a /30 point to point connection. Everything works fine, I'm just not sure how to connect the second switch to the firewall. Should I use the a different /30 for the point to point connection to csw02 gi0/48? (See attachment) How would this affect traffic flowing through this interface? Would I have to duplicate rules I have on my inside (gi0/2) interface? Is there a way to make the inside2 interface standby some how? I want to know the best way to set this up, so in the event csw01 goes down I don't loose internet. Will EIGRP work it's magic and only use 1 path to the ASA? Should I even be using routed interfaces on the ASA and just use trunked mode?Running ASA 8.4?
i got an error while connecting to my PIX (515e) via ssh connection there is an error message appears (The server has disconnected with error, server message reads: Internal Error) and at the console session at the time time, the following message appears also (process_create: out of memory)
I was just wondering if it's possible with an ASA 5510 to connect to the external IP address of an internal server from inside the network. I have already set up dns doctoring for dns lookups, and everything is working fine there. We have an application inside the network that tries to connect straight to the external Ip of another internal server. where to look in the ASDM 6.4?
I was handed a firewall ASA 5520 but without external flash, I want to confirm that the ASA at least boot from rommon mode boot must have the external flash connected? I connected to power and I connect it by the console port it did not show any boot.Additionally I can confirm it is possible that you can connect a flash of a previous ASA model, say a 5510?
I have DSL service with AT&T and I have a Motorola 3360 modem. We also have a /28 network of static IPs from AT&T. When I login using PPPoE on the modem it gets x.x.x.190 as it's address. Our range is 177-190. I have two ASA 5510s in an active/passive failover configuration with the Ethernet port of the modem and one interface of each of the ASAs on a dumb layer 2 switch.
I want to setup this DSL connection as a backup to our main Internet connection. I cannot figure out what setting on the DSL modem to use to make this happen. I know I cannot use PPPoE in a failover setting so I can't have the modem in bridged mode. There is some mode where it passes the 190 address to the connected device and when I plug in a PC directly to the modem and set it for DHCP it does get 190 as it's address. So do I configure the ASA interface as 190 with one of the other addresses as it's standby? What do I set my route on the ASA to for use of this connection? Can I then make use of these other static addresses when plugging other devices into the layer 2 switch?