Belkin Routers :: N750 - Access Point Support Of Guest Access

Jan 9, 2013

Does the N750 (F9K1103V1) support Guest Access while in Access Point mode? It will not provide an IP address when a guest attempts to connect.

View 20 Replies


ADVERTISEMENT

Belkin Routers :: F9K1102 V1 Guest Access While In Access Point Mode

Jan 17, 2013

I have an n600 ( F9K1102 v1 , firmware 1.00.09 ). My ISP provides my main router for my network, but I want to use the N600 as an access point, I have activated the "Use as Access Point" feature.Is it possible to still utilize the Guest Access feature in this case?

View 1 Replies View Related

Belkin N750 - Find IP Of Access Point?

Jun 28, 2013

I have a home network, using Belkin N750 as main router and wired ASUS RT-N12C1 which was set as AP mode. How can I find the IP of ASUS RT-N12C1 to change channel?

View 4 Replies View Related

Belkin Routers :: N750 - Wired Connection Can Ping But No Internet Access

Mar 30, 2013

Belkin N750 Router - wired connection can not access Internet. I've tried direct to modem and have no problem, have tried old router, no problem, but if I shut down desktop completely (Win7) and restart, I get no connection. Uninstalling the NIC (Intel 82579V Giga) and restarting, then I get connection again. However, if I start in safe mode with networking, I have no problems at all. I've disabled my firewall to no avail.

View 3 Replies View Related

Belkin Routers :: N600 - Unable To Access Dashboard In Access Point Mode?

Mar 6, 2013

Setup N600 DB as an access point using the most recent firmware,3.03.12? Once I do I'm not able to access the dashboard even through I enabled the remote management option.

View 2 Replies View Related

Belkin Routers :: No Guest Access On N300 F9K1002v1?

Jun 1, 2013

I have a N300 f9k1002v1 router and would like to add guest access. Unfortuantely I can't find any info on how to do this. The user guide alludes to it but has no details. I also checked out this link: [URL]

since my router setp does not show "guest access" under "wireless" I skipped to #6 as stated. However when I get to #9 there is no "guest settings" dropdown for me to use.

View 1 Replies View Related

Belkin Routers :: Using F5D7230-4 As Access Point?

Dec 20, 2012

Can I use my F5D7230-4 as an access point? I need to provide a hardwired ethernet connection to my A/V reciever but not have a wired port in the area of my house. I have an existing wireless router thru Century Link. Could I have the Belkin attach itself to the wireless network and then have a cat 5 come out of one of the four ports to connect my A/V reciever to the network?

View 1 Replies View Related

Cisco Routers :: RV180W Add Access Point With Roaming Support?

Oct 20, 2012

I have a customer with a RV180w running the latest firmware.  We are currently using the router as a router and to provide wireless access.  We want to add wireless coverage and I am interested in our options.  We have a ethernet backbone which we could use to give the new AP LAN connectivity.  Can we buy another RV180W and use it in AP mode and provide roaming wireless connectivty.  The client wants a guest and business WLAN so we will use the VLAN feature of the router.  How do we configure the new AP?  Do we need to use WDS?   If we use WDS, can we still use WPA2?

View 6 Replies View Related

Belkin Routers :: 5FD8235-4 V2 - Access Point Setup

Feb 2, 2013

If I want to setup my N+ router 5FD8235-4 V 2 as an access point. How do I go about doing that?

View 5 Replies View Related

Belkin Routers :: F9K1102 V3 Access Point IP Error

Mar 23, 2013

When I set up the Belkin F9K1102 as an access point I can no longer access it via the ip-address and it does not accept the new ip-address I've given it, but takes the ip-address 192.168.2.254, while my network is on the 192.168.1.XXX address series. The only way I can do this is by manually given the router a new address, then manually turn of the DHCP- server and finally move the internet cable from the WAN port to one of the LAN ports - but then the LED-indicator on the router is blinkin red.

View 2 Replies View Related

Belkin Routers :: N600 - Access Point Addition

Dec 28, 2012

I have a Belkin Play N600 as my primary and have an older Belkin G+MiMO that I'd like to connect as an access point only. Any step by step instructions of how to accomplish this?

View 1 Replies View Related

Belkin Routers :: Configuring An Older 5FD8230-4 As Access Point?

Dec 16, 2012

I am trying to configure an older Belkin Router (Model Number 5FD8230-4) as an Access Point so that I can boost the range of my network. The problem I have is in configuring the old router. It won't allow me to change any settings, or at least the changes don't stick, even after clicking "apply changes". I tried creating an administrative password but I am not even sure that this is working. I am using a Macbook, so perhaps this is an Apple compatibility issue. I have tried resetting the router and reverting to Factory default settings, but no joy.

View 3 Replies View Related

Belkin Routers :: Setting Up Max N300 As Access Point With USB Drive

Dec 17, 2012

I wanted to set Belkin Share Max n300 as an access point. I followed the instructions, set the IP address to the suggested one and connected it to the main router. It worked, computer connected to the Belkin via wire was getting IP address from DHCP on main router. But: The Belkin device itself became invisible. I lost connection to Belkin device via config page via HTTP. It does not respond to any IP address so I actually cannot use it for purpose I wanted to set up secondary Wi-fi, I just cannot configure it. Also I wanted to use USB ports of the Belkin to connect external drives. I cannot do it as well. More over it does not go back. It does not reset to the original router option.

View 2 Replies View Related

Cisco Wireless :: 2960 - Autonomous Access Point / Get Guest To Access Internet?

May 9, 2012

I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.

I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.          

View 10 Replies View Related

Belkin Routers :: Configure N300 As Access Point - Unidentified Network?

Nov 9, 2012

As per settings menu, I tried to give it an IP address but the new address is not accessible for further configuration. When I connected to the router it status changes to "unidentified network".

My primary network address range is 192.168.1.1 to 192.168.1.10. So I gave address to belkin as 192.168.1.100. But I can not access this address from both primary and belkin network.

View 2 Replies View Related

Belkin Routers :: N300 Wireless Bridges Be Connected To Same Access Point

Nov 21, 2012

Can 2 N300 wireless bridges be connected to the same wireless access point ?

View 1 Replies View Related

Belkin Routers :: N600DB Using Router As Access Point / Range Extender

May 16, 2013

I have a N600DB configured as a primary router. I got another playmax n600HD router which I want to configure as an access point that extends my network upstairs and allows me to attach some wired devices like my ps3. I followed the basic principles of setting as access point and my locally connected ps3 and NAS are communicating but no Internet access. How the 2nd router can connect to the internet?

View 2 Replies View Related

Linksys Access Point :: Access Guest Account Through WAP54G?

Jun 9, 2011

My network is such that I want to extend the signal of the GUEST account.  I have a WAP54G set up for that purpose and am getting a very strong signal.  I can access the main network, but not the Guest, I cannot even see the GUEST access. Any setting change that needs to be made that will allow me to access the GUEST account from the Access Point?

View 2 Replies View Related

TP-Link Dual-Band Wireless :: How To Configure N750 As Access Point

Dec 5, 2012

Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : 3.13.23 Build 120810 Rel 44064nHow do I configure the TP-Link N750 wireless router model TL-WDR4300 as an access point so that computers/nodes on the WAN, LAN and wifi connections of this device are all on the same network/subnet?From the admin browser page, disabling DHCP and NAT does not provide the desired results.

View 10 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

Cisco Wireless :: Does WAP4410N Support Guest Access?

Sep 13, 2011

Does the Linksys AP (WAP4410N) support Wireless Guest access solution?

View 2 Replies View Related

D-Link DIR-655 :: Access Point With Guest Zone

Mar 23, 2010

I recently picked up a 655 with hardware version A2 and flashed to the latest firmware.  I have a HotBrick router.  I only want to use the 655 as an access point AND especially to use the Guest Access or Guest Zone feature to allow visitors to bring their laptops and not virus up my network.  My home network is open among a few computers for things like SageTV, file serving, etc.I can get the 655 to function just fine as a standard access point by following the instructions to turn off UPNP, DHCP, etc. as outlined in the manual.  I then enable the Guest Access/Zone  feature, and of course give it a different SSID name, make sure it's on 24 hours a day, that it is enabled, etc.

But, none of my computers can access the internet via the Guest Account feature, just the regular wireless portion.  They show connecting to the Guest Account name, etc. but no internet.  I've disabled every security feature I know of to test this.  Again, the "regular" WAP tests great, but no Guest Account, which is really important and one of the main reasons I bought the unit.I'm wondering - does the Guest Account feature only work if the 655 is the main router, has DHCP enabled, etc.?  Does it have to be the one and only router?  If so, I'm in trouble, because I can't really give up my HotBrick due to failover features, etc.

View 5 Replies View Related

Belkin Routers :: Connect To VPN Through N750?

Mar 18, 2013

I connect to a VPN for work at home and I connect directly to the router not wirelessly but I am having trouble keeping my VPN connection.

View 1 Replies View Related

Linksys Wireless Router :: E2500 May Support Multiple APs For Guest Access?

Dec 20, 2011

I got 5 E2500 routers and the main one has setup to IP address 192.168.1.254 and the rest APs are programmed into the bridge mode with the IP address 192.168.1.245 through 248. The secured wireless network  works fine when I roaming between these APs but the only AP that I can get internet access for guest wireless network is the main (192.168.1.254) router; for every other APs, I will get the guest log on screen (prompt for guest access password) and no internet access after I type in the correct access password. Does the E2500 support multiple APs guest or it requires a special way to configure it?

View 5 Replies View Related

Belkin Routers :: N750 DB USB Printer Not Connecting?

Dec 20, 2012

N750 DB USB printer not connecting. I'm currently running a Canon MP480 multi-purpose printer connected through USB to the N750 DB router. I have both the printer driver and Belkin USB Print and Storage Manager software installed on a desktop PC that connects wirelessly to the router. The Belkin print manager software "sees" the printer, but when I try to connect it says please install printer drivers. I've installed and re-installed these drivers a few times, with no effects.

View 14 Replies View Related

Belkin Routers :: N750 LAN Speed Is Limited To 5Mb?

Dec 15, 2012

My N750 F1103 (f/w 1.10.16) LAN speed is limited to 5Mb why? I upgraded my Internet bandwidth to 20Mb+ tested and found it was only 5Mb, the cable company checked a few things and then I did some diagnostics and Isolated to the N750. I have two wired PC and same results with both PC's. This is supposed to have Giga bit LAN not Giggle bit LAN! I'm paying for something I cannot used to its full potential.

View 5 Replies View Related

Belkin Routers :: N750 - How To Change Name Of Network

Jan 15, 2013

I just bought an N750. Setup was ok once my modem was recognized. How do I change the name of my network now that the router is installed and working?

View 2 Replies View Related

Belkin Routers :: N750 Reboots But Still Holds Same IP

Jan 9, 2013

I have a N750 and I want to change the IP address through the browser. It is the standard 192.168.2.1 config. I change the IP to 192.168.15.x while hard wired and hit apply. The router reboots but still holds the same IP.

View 1 Replies View Related

Belkin Routers :: How To Get Port Forwarding On N750 Db

Feb 8, 2012

how do i do port forwarding on my belkin n750 db i want to view my cams when not home i can view on my network not tmobile?

View 3 Replies View Related

Belkin Routers :: N750 AV Cannot Airprint With HP 7520

Dec 27, 2012

I cannot airprint. Contacted email support. Followed instructions to reset router. I did and I was able to print from my iPhone. ONCE. Then I installed my SSID and passwords and WIFI setup again and now I can't print. I have a brand-new airprint equipped HP 7520, an iPhone and 2 iPads.that I want to print from....the router is a N750 AV bought in July.

View 1 Replies View Related

Cisco Wireless :: 5508WLC Whitelist For Guest Access And Securing Guest-access?

Aug 18, 2011

Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment

View 4 Replies View Related

Linksys Access Point :: E4200 / E1500 - Cascading Routers Versus Access Points?

Nov 24, 2011

I am trying to find an effective way to extend the wireless signal across our home. I have tried various different solutions. Currently, I have an e4200 primary router that is cascaded with two additional e1500 routers that have been configured as access points. The Linksys support team hosted my computer and configured the devices. The e1500 routers are connected via ethernet wires running through the walls. And, this seems to be working well. Here's my question. The e1500 routers are configured with different SSID names, which Linksys advised was required to avoid conflicts in communications from the three router devices. Is there any way to configure this set up or something similar so that the entire wireless network has the same SSID and is seamless. In the current configuration, I have to specifically connect to the primary router or one of the two access points.

View 3 Replies View Related

Netgear Wndr4500 N900 Guest Wifi On Access Point Has No Internet

Jul 24, 2012

I have the Netgear wndr4500 router setup as an AP. The wndr4500 has a feature for guest wifi but will not connect to the internet. The main wifi will connect to the internet fine. I'm wondering if I use the WNDR4500 as an AP, the guest features do not work?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved