Broadband :: Connect 2 ADSL Routers On 1 BT Line?

Feb 19, 2011

Our church has 1 phone line, we run BTBusiness Broadband at one of the building where we have a couple of charities based. We have the phone line connected to an extension at the other end (where the Church is) >80m away. Any way of running a second concurrent router on the extension so I can set up an office with a VOIP number, pC's printers etc there too? We use Devolo ethernet over mains and wireless for the main building, but the church itself is on a completely seperate mains power supply so I can't use that. I could run 100m Cat 5 and locate a switch on that, but any way of achieving something similar over the phone cable which is already in place.

View 2 Replies


ADVERTISEMENT

E1000 - Use ADSL Line With Broadband Router?

Aug 16, 2012

I have a broadband router (Linksys E1000) which I've flashed with a DD-WRT firmware. After doing so I realized that this router doesn't have an interface for ADSL port(RJ-11). How can I use the Linksys E1000 for my home network?

I've heard that I can use ADSL modem(not a router) & plug the RJ-11 to it & take from it the Ethernet & plug it back to the E1000(in the WAN port) would that mean that I can get just a modem and not a hybrid?

Note: Also, I have to mention that my ISP is using PPPoA & DD-WRT is not supporting it, but i googled & they said that the ADSL modem cab be the rescue. Can I pick any ADSL modem for this specific scenario or am I looking at a specific model?

Secondly, can I use my old router to do the job instead of buying a new ADSL modem ? & is it a good approach ? or should i buy a new ADSL modem ?

Update i turned my DD-WRT router(E1000) to act as access point, since this is the only way that i can use it with the DD-WRT feature. & i think this is better than have nothing :) I can now have the DD-WRT functions ;)

View 1 Replies View Related

Installing 2 Adsl Routers On One Telephone Line

Mar 28, 2011

Can I install 2 ADSL routers on one telephone line with SKY. If I can does this mean that if sky give me 20mb connection, I can get two lots of 20mb using the two routers.

View 2 Replies View Related

Cisco WAN :: Connecting ADSL Line On HWIC-ADSL On Router 2901?

Aug 24, 2012

i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday   the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?

View 2 Replies View Related

Broadband :: LAN Software For Two Broadband Line

Mar 26, 2011

i have two broadband line in a lan. it is physically connected to same switch then same switch to connected other computers.now, i want to when one broadband line down or disconnected in the mean time another broadband line automatically backup internet line. so i want to free software for this reason to get these solution.

View 1 Replies View Related

Routers / Switches :: Possible To Connect 2 Routers To One Phone Line

Apr 30, 2011

Can I connect 2 routers to one phone line so that I can receive a wireless internet connection throughout my house?

View 1 Replies View Related

Best Modem For 24Mbps ADSL Line?

Jan 27, 2011

I have D-link 2640U ADSL2+ modem. Now I have 12Mbps / 1Mbps internet connection. I am planning to move to 24Mbps /1Mbps intenet connection and I want to know if this modem is enough. What is the best modem so I get the full 24Mbps[CODE]

View 7 Replies View Related

Cisco WAN :: 877 - ADSL Line Drops

Nov 8, 2010

We have a fairly major problem with some of our Cisco 877 units (5 in all). All are running 15.2(2)T2 in order to make use of zone-based firewalls and virtual reassembly, and all are exhibiting the same problem. When our ADSL line drops this si shown in syslog 
 
2010-11-09 01:03:06    Local7.Info    192.168.7.1    4733: Nov  9 01:03:05.707: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41799 on zone-pair OutsideToInside class cm-MainServerServices due to  RST inside current window with ip ident 02010-11-09 01:04:06    Local7.Info    192.168.7.1    4734: Nov  9 01:04:05.946: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41809 on zone-pair OutsideToInside class cm-MainServerServices due to  RST inside current window with ip ident
[code]...
 
The "no retrain. sleep 20 seconds" messages continue forever more until somebody power-cycles the router - which is a bit inconvenient as two are 300 miles away. Surprisingly, our event manager applet isn't triggering the reload either, which defeats the object.

View 15 Replies View Related

Cisco WAN :: ADSL Line Do Not Activate With 1801

Oct 9, 2012

ADSL line do not activate. Telco Confirmed Like is Okay . They have tested no issue observed. Router replaced but did not work. Supspecting Firmware not compatible with telco . Not sure how to confirm on this.

sh ver
Cisco IOS Software, C180X Software (C180X-ADVIPSERVICESK9-M), Version 12.4(4)XC7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Tue 31-Jul-07 20:24 by alnguyen
ROM: System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2)
XXXXXXXXXXXXXXXXXXXXXXX uptime is 30 minutes
System returned to ROM by reload at 18:48:26 UTC Wed Oct 10 2012
System image file is "flash:c180x-advipservicesk9-mz.124-4.XC7.bin"(code)

View 1 Replies View Related

Cisco WAN :: 1800 - Use ADSL As Backup Line?

Jun 27, 2012

Site A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 5510.My question is, can i use the existing ADSL line to be use as a backup line if the leased line is down on any of the site??
 
And i want it to trigger itself, once the leased line is down, the firewall UP the backup line? something like that..

View 4 Replies View Related

Linksys Cable / DSL :: X3000 ADSL Line Down

Nov 21, 2012

I have ADSL  router Linksys X3000, but I have an issue with it. I have configured it properly (based on internet provider's manual), repeatedly checked it, but router still says that ADSL line is down. I have also another router from Zyxel and it works perfect with same wire and configuration, so I guess the line is fine.
  
PPP generic driver version 2.4.2 79 PPP Deflate Compression module registered 88 PPP BSD Compression module registered 84 PPPoL2TP kernel driver, V1.0 75 ccp_autowan_sm_thread=> Starts in Unconfigured mode, detecting state! 125 ->

[Code]....

View 4 Replies View Related

Process To Connect Two ADSL Routers?

Feb 23, 2012

Tell me the process to connect TWO ADSL Router

View 1 Replies View Related

Cisco WAN :: How To Find Adsl Line Number From 886VA

Mar 28, 2012

Is there a way to find in a remote branch the adsl line number in a cisco router 886VA.
 
When giving show controllers vdsl 0
 
we can see the upload/download speed but there is no information about the line number. We need this information in order to troubleshoot adsl line problems with our ISP's in remote branch offices.

View 3 Replies View Related

Cisco Infrastructure :: Will WIC SHDSL-V3 Able To Support ADSL Line

Apr 10, 2013

I do have a question, is WIC-1SHDSL-V3 able to support ADSL line?
 
We have WIC-1SHDSL-V3 module used for SDSL line, due to few site need to bring up with ADSL line with 1841 model, but HWIC-1ADSL module already EOS. The replacement model EHWIC-VA-DSL-A is not compatible to 1841. My architect suggest Symmetric Module like WIC-1SHDSL-V3 could be able to tweak the config to support Asymmetric purpose. I did google but do not found such related topic. Can any expert on this area to advice me?

View 1 Replies View Related

Routers / Switches :: Connect 2 Adsl Devices Together?

Mar 1, 2011

A Telindus 1421 SHDSL Router and a Sagem F@st 1500WG wireless adsl router.The question is: Can i connect this two devices directly over the adsl port and share networks on each side of each of the devices?

View 3 Replies View Related

Linksys Cable / DSL :: How To Access ADSL Line Stats On X2000

Mar 5, 2012

On my old router I could access the line stats on the home page giving me Attenuation  and SNR margin, this allowed me to keep an eye on line quality, there seems to be no equivalent info on the X2000. Is this on a hidden page like the advanced wireless page.

View 1 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR702N - Networking Without Available Adsl Line?

Feb 14, 2013

Region : Argentina
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :

Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : ?
ISP : Manx net

Within a property without an available adsl line I'm simply trying to network a wireless laptop with a wireless printer. Both devices recognise the router, etc, but problem sending file for printing to the printer. (laptop does not detect printer). Is the lack of an internet connection the issue or simply a configuration issue?

View 9 Replies View Related

Cisco WAN :: 1800 / 2800 / 2900 - Using ADSL As Backup Line

Aug 1, 2011

Site A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 5510.My question is, can i use the existing ADSL line to be use as a backup line if the leased line is down on any of the site??And i want it to trigger itself, once the leased line is down, the firewall UP the backup line? something like that..

View 1 Replies View Related

Routers / Switches :: To Connect ADSL Direct To Computer

Dec 2, 2012

I have CentOS and the application I am running does not listen on 192.168.1.5 (Private IP address). Right now I have connected using bridge mode and I can see in my network configuration-> ppp and eth0. PPP has public IP and eth0 has private IP. Is there any way that I can get public ip assigned to eth0? I do not have Static IP, I want to use the public dynamic IP assigned by my ISP to use in eth0 interface.

View 2 Replies View Related

Routers / Switches :: How To Connect ADSL And 3G Router On Network

Aug 7, 2012

I have one ADSL router that I have configured Port Forwarding on it, but the internet is very slow. I also have another 3G router and I want to use it for internet because it is much faster, but it cannot do Port Forwarding. How can I connect this two routers in one network such that ADSL router is for Port Forwarding only and 3G router is for internet only?

View 1 Replies View Related

Linksys Cable / DSL :: WAG120 - Connect Two ADSL Routers?

Feb 14, 2012

I was using Linksys ADSL router ( WAG120) as modem router. Recently I bought new Linksys x3000 and installed a modem router in place of WAG120. Now i would like to connect the both routers to get the signals in first floor of my house.

View 9 Replies View Related

6867R - Network Cable Is Unplugged When Plug ADSL Line To Router?

Nov 20, 2011

I can connect to my router but not to Internet, it seams that ADSL line "disconnects" my LAN/WLAN this issue is with Inalambrico 6867R router an other router, TP-Link is working great

View 1 Replies View Related

Linksys Cable / DSL :: WAG320 Constantly Dropping ADSL Line Every Few Hours?

Jan 11, 2010

I have bought a WAG320 & ever since I've had it the ADSL line keeps dropping every few hours. The LAN network is fine & I have 7 computers connected to the router wirelessly. When I press the re-set button on the back of the router everything is fine for a few hours then it starts doing it again?

View 9 Replies View Related

Cisco Switching/Routing :: 877W ADSL Line Interface Not Initializing?

Jan 19, 2012

Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
 
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?

View 3 Replies View Related

Cisco Routers :: Total Failure To Get SR520-ADSL-K9 To Connect To ISP

Dec 15, 2011

We've (an independent school) just bought an SR520 with a view to replacing one of our Draytek 2820s. We need to set up some site-to-site VPN with NAT and the Drayteks won't do it.
 
I've been trying to configure the SR520 in just the most basic fashion using CCA (3.1) and the CLI but with no success. I can't get a PPP connection with our ISP.
 
I've tried following the instructions in the software config pdf and also tried replicating the various 'running configs' reported in other posts in this forum to allow connection to a UK ISP, with no success. I don't know how many times I've reset the poor thing to factory defaults.
 
I have to say that I'm dismayed at how flaky the CCA appears to be. Many of the things I've tried with it simply don't work and often end up in it hanging. Close to useless in my view.
 
So instead I've tried to use the CLI which seems a lot more solid but is somewhat impenetrable and there's precious little by way of supporting explanation.

View 12 Replies View Related

Cisco WAN :: Poor Performance / Packet Loss With 887VA Router On ADSL Line

Dec 6, 2012

We have a remote site connected to ADSL line with a Cisco 887VA router attached. This has been working fine for the last couple of months. However, recently, the site have started to complain of performance issues (network slow, applications disconnecting, etc)Looking on the router, we can see evidence of packet loss/timeouts from a simple ping to the internet e.g. [code]
 
However, we have logged the fault with our service provider and they return all line tests as clear but what is particularly strange is that they also report “and the SNR Margins are well within threshold levels (Upstream 11.5 and Downstream 15.0)” which, unless I’m misunderstanding something, seems to be completely different from what the router itself is reporting.Is there a reason why the service provider’s stats for Noise Margin would appear to be so different from what the router is reporting?

View 2 Replies View Related

Cisco Switching/Routing :: 887 Router / 1841 - Dial Up On ADSL Line To New Site

Nov 9, 2012

I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
 
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
 
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.

View 7 Replies View Related

Broadband :: Two DSL Modems On One Phone Line

Apr 11, 2011

In a house that is too large for a small wireless modem to send a signal far enough, is it possible to use a second modem in the same phone line (not at the same time). Filters are used in the spare phone jacks.My main question is: when modem A is being used and modem B is switched off, is it necessary for the splitter for modem B to be removed and the filter put in its place? Or is the fact that modem B is switched off sufficient? I suspect that it's necessary and that's why my friend gets very slow download speeds even when the other modem is off.She insists that it used to work but I think she was just lucky if it used to work.

View 2 Replies View Related

Routers / Switches :: Connect Win98 To ADSl Modem Over The Network Switch?

Apr 19, 2012

Have one switch and network.PC number one have win98 and network adapter and connected to the switch.PC number two have winXP and network adapter and connected to the switch same as win98.Network works on win98 and winxp they see each other.internet working on winxp but dont work on win98

View 2 Replies View Related

Split TS And Main Server - Separate Broadband Line?

Aug 29, 2011

1.I want to have a seperate Broadband line for a Server running TS for certain users to log into to.

2. I want another broadband line that is split via switch for other users and servers.

Reason: Speed up connection for TS users so that are on a dedicated line.

How will I get TS Server to speak with my Main File server to access the files they need and there is 1 folder both networks should have access to?

TS server and Main server in Same building. Don't want to use a WAN routers to connect the 2 routers together. My Broadband (According to speedtest.net = 12Mbps DL/ 0.80Mbps UL)

View 2 Replies View Related

Broadband :: Adsl Modem / Router Mac Changing In Dos Prompt?

Jan 26, 2012

Modem/router mac address changer .. i have globe wimax bm622i model, that needs to be change its mac address, hardly to find a right software, so i decide to manually config and do it by ms-dos commands, any related command for dos to change mac address of globe-wimax-bm622i-model.

View 1 Replies View Related

Home Network :: Connect Two Routers With One Broadband Connection?

Jul 29, 2012

i have triple storey house. in all three floors a broadband connection point (rj45 jack) is there. i have connected one wireless router in 3rd floor. but the signals are not coming on second floor. can i connect netgear wireless access point with one ethernet point in the 2nd floor broadband connection jack (Rj 45), to access wirelessly my internet?

View 1 Replies View Related

Broadband :: Telephone Line Jack Not Receiving Dial Tone On Laptop

Dec 26, 2011

I can not get onto the internet via dial up. The message says that I have no dial tone. Using the same line, I get a dial tone on the phone. I can get onto the internet via a DSL connection, but it will not make a connection when I have a telehone line inserted in the phone line jack. This problem started after the power went off and on quickly two times. I have followed all the instructions that I have found to reset the modem, but to no avail. Is it possible that the phone line jack needs to be replaced.I have a gateway laptop with Vista program.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved