I found this good guide how to do it, but some things remain unexplained to meI would like to get more information about step:3. Change the IP address of your current PCMaybe more questions will follow, but that's the only problem I am having right now.
View 11 RepliesI tried changing my ip address using ipconfig / release. I tried to fix what I did using ipconfig /renew but it tells me no operations can be performed on local connection 5 while it's media is connected.
View 12 Replies View RelatedI am trying to configure a router with a satellite connection. I am following a HughesNet guidline. At step four after typing in the required IP address , nothing happens.There is no place to type user name and password.
View 2 Replies View RelatedHow to change ip address in windows 7?
View 1 Replies View RelatedI am connected to a static ip network. This network sets local ips to connected computers but general ip is the same: static ip of network. When i go to "whatismyipaddress", I can see this static ip. I want to change my ip address. I have no chance to use proxy server or router connection. Is there a way to change my ip address? (Because some sites ban ip address, ex:rapidshare etc. and I need to change my ip)
View 1 Replies View RelatedI've had the same IP address for years and want to change it to a new one - I have a dynamic IP but for some reason it will never change.It looks as if it's always static-what settings I need to change on Windows 7 to get it to roll over onto a new IP address?
View 1 Replies View RelatedTrying to change my IP address in windows 7. I downloaded Desktop Central 7.Server and Desktop Management Software: Now what am I suppose to do?
View 2 Replies View RelatedI need to change the IP address of existing primary cisco ACS 4.2 (windows based). What is the required procedure to change the IP address?
View 4 Replies View RelatedHow can I change my ip address on windows 7. Someone hacked my computer before and now im afraid that he will do it again. I want to secure it by changing my ip address..
View 2 Replies View RelatedMy Network is running Windows Server 2003 and with more than 150 Users. But last week, I notice that a program is changing my DHCP server IP Address scope.
View 2 Replies View Relatedwell i had the same problem because i got bored and i was like hmm i wonder if i can change my IP and i tried it and i had the same problem but when i did system restore it still did not work, now i have to get a new operateing system...
View 10 Replies View RelatedI have a new router. this seems to be a very simple problem relating to the most basic configuration options.
Hardware Version: A1 Firmware Version : 1.01NA
go to SETUP -> "NETWORK SETTINGS"
change "Router IP Address" to 192.168.73.1
change "DHCP IP Address Range" to: 192.168.73.10 : 192.168.73.200
Save Changes Wait for reboot. change my client system's local IP address... so that I can reconnect. direct web browser to http://192.168.73.1/
seen: login page has a select-box for a userid, but no text inside. there is no prompt to ask me to login. I press enter (or whatever... I login). every form interface on all web pages looked at have no labels on text boxes.
I did a view source... and used web-dev tools to look at the page. it looks like the apparent js function, show_words(), is not defined.
change ip address and dhcp address range back to default save changes. wait for reboot. reverse changes to local system things are back to normal. login page has useful text. after logging in, there is something to read.
looking at source again. I see, now, that the js function "show_words" is defined in a file called public.js.
I added a new server and created a new static NAT assignment on the ASA 5510 to the server's IP. When I browse to the web to check what public IP it's reporting, it shows the wrong IP. I disabled the network interface on the server, ran "clear xslate", reenabled the network interface, ran "sho xlate" and while the correct translation was in the table, the server still reported the wrong IP address.I even ran a packet trace and it showed the IP address being correctly translated to the proper public IP, but when I browse to the web I get the same erroneous public IP. [code]
View 8 Replies View RelatedI have a new 881 router and am simply trying to change the ip address from the default 10.10.10.1 to 192.168.15.1
I tried doing this both in the CCP Express app loaded on the router, and also using the desktop CCP client. I can change other parameters without any problems, but when I change the ip address of the vlan the program hangs (as expected since the ip address should be changing). I then try to open it back up and reconnect but get no response from the router.
I can ping it no problem, and the http server is running according to the serial terminal.
How i can change my ip address without changing my internet connection??
View 3 Replies View RelatedMuch of the time my wireless printer is offline relative to computers on my LAN because the IP Address has been changed to some value different than what the computer thinks it should be. So I have to figure out what the IP Address is of the printer then modify the printer port on the PC to point to the correct address. If this only happened rarely or if I could easily remember the steps I have to take to remedy the situation, I guess this would not be such a big deal. But it happens a lot and I'm old and alzheimery. So my question is: how do I get the router to assign the same IP Address to the printer all of the time?
View 2 Replies View Relatedhow to change the IP Address on a Dell C3760dn Color Laser Printer?
View 4 Replies View RelatedI'm adding another router to my home network to extend my WiFi range. (Linksys e2500.) I'm trying to change its IP from the default 192.168.1.1 so that it doesn't conflict with my primary (dhcp) router.
To isolate matters I've reset the router to factory settings, turned off my mac's WiFi and then connected the Mac to a Lan port on the router. Now I can view the router's admin page at 192.168.1.1.
Now I change its local IP to 192.168.1.3 and leave the subnet as 255.255.255.0. The router reboots and after several minutes is inaccessible at any IP I try (still hardwired to the Mac with WiFi off). Ifconfig doesn't show the router and the only way I can get it back is to factory reset it again.
I have verizon fios internet and a wireless home network with verizon internet security and I want to ghange my IP adress on my laptop
View 6 Replies View RelatedI've finally gotten tired of Netzero Dialup and want to change to dsl from U Verse. That brings up some questions. Do I cancel Netzero when I start U Verse or do I need Netzero to make it work? If I have to cancel Netzero can I transfer my favorites over to dsl? How difficult is it to set up dsl? Does the box come by UPS of Fed Ex?
View 6 Replies View RelatedI tried changing the WEP to WPA because I recently found out our neighbors were stealing internet from us. However after doing all this changing around I used 192.168... And all that and was able to change the ssid and the passphrase but after doing so the Internet stopped working. We are able to connect but it says there's no service or limited connectivity so no web pages or anything loads. Now I can't get back to the router page by typing that 192.168. stuff because there's no Internet. Don't know what to do. This is my fathers ISP and it's not the greatest considering the location. I've tried unplugging the router and whatnot but that's not working either. I think we need to get back on the router page and fix something but it's not allowing us to since there's no Internet. Am I going to have to change back to a WEP.. I dont really want too. The router may need to be upgraded too because it's pretty ancient.
View 4 Replies View RelatedA router restart. I changed the wpa to wen so I could connect my ds to wifi.So far what I have done was restart the modem, it's a Cisco wag120n. This is a wireless so the moment I changed to wen, I lost connection. I then used a cable to connect to the modem and managed to change the settings in the router page 192.168.1.1 back to wpa but with no success connecting to the Internet. I then tried ressetting the modem and computer with no luck. I cut the power to the modem router and turned off computer for 5 minutes. I then turned the modem back til it was stable and then the computer, again with no luck. I then factory reset via the button manually and via the modem page but both ended up with the unable to connect to primary DNS server.
View 6 Replies View RelatedI have been trawling the interenet looking for an answer to the i but to no avail.Can you change the source port that windows uses when it makes a connection to another host.
[code]...
I had to assigne my PC a new static IP address and now other computers cannot access the shared printer attached to this PC . It still show up in the printer pane of the other computers but you cannot print to it. The local PC attached to it via USB will printer fine.
View 4 Replies View RelatedMy exchange server should have an outside interface ending in .82 which is one of public IP's assigned to it.Inside 192.168.168.250 -> Outside x.x.x.82 How can I configure this in ASA 8.4(1)?
View 3 Replies View RelatedBack in may, I built my own gaming rig and have been using wireless on it all the time. But recently my speeds has been going down, and i can't be bothered to fix it. That's why i wanted to use ethernet on it. My problem is that there is only one port on my modem for Internet, and that is being used by a routher that goes upstairs.
As you can see, i have three TV ports and one PC port. All of it is being used.One of the TV ports goes trough the wall too a exit in my wall, and goes into my TV Router as seen on the image below.
Everyday a few of the computer will error with "A duplicate name exists on the network:" A quick Google search shows the same answer EVERYWHERE on the internet. So I changed the names of a few of the computers too something I knew was unique. Still though the problem persists/ it afters the two XP bases computers the most, but my main workstations (windows 7 sp1) has had this error a few times, although it appears to have left for a while. I have a feenas server but Active directory is not turned on.My router is a e4200. I was using DHCP server on there (and would very much still like to) although I have turning it off, rebooted both the router and the computers but to no avail.
View 19 Replies View RelatedEvery so often (random amounts of time) my internet setting either on the router or pc change and then I it comes up with an error that my settings aren't the same as my router... I use a Orange Live box and windows 7. also when I want to sign into games for windows that sometime crashes the internet and on DOW2 and minecraft.
View 10 Replies View Relatedi am willing to know that how we will refresh our WAN IP's dynamically.
View 3 Replies View RelatedHow do I change my security key on my laptop?
View 1 Replies View RelatedI play this hockey.tk game. I want to change my ip to a different nearby state. For example, If I live in new jersey i'd want to change my ip to New York so I can play the game. How do I change my ip to that? For some reason I got ip blocked on a game.. So I was wondering if there was any way to do that
View 3 Replies View RelatedHow to change the security key. How does one go bout that? Did not see that within the manual for some strange reason.
View 1 Replies View Relatedhow to change the ARP timer in CISCO. I know how to change th mac-address aging timer, but can't seem to find any documents on how to change the ARP timer from 4 hours.
View 2 Replies View Related