Cisco :: 1140 APs - No Ping To Host From Local LAN
Apr 3, 2013
I'm using 3 AP's 1140 with local authentication using local radius (flex connect mode).the radius server im using is MS 2008 R2.authentication is working great on all devices pc's&mobile.authentication method is PEAP wpa2 aes enterprise.after 3 or 4 hours devices loose connectivity to the web.the device seems to be still connected to the ap but there is no ping to host from local lan or any arp learnd on local router.only manual disconnect on device and reconnecting brings connectivity up again.in one case only reseting the AP's worked.
View 6 Replies
ADVERTISEMENT
Jun 27, 2011
I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.
View 2 Replies
View Related
May 7, 2012
ASA 5510
Ver 8.2(5)
I have been looking all over the place for the answer of how to allow clients on an IPSEC VPN to ping from host to host.
View 4 Replies
View Related
Feb 10, 2011
I'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...
View 2 Replies
View Related
Dec 12, 2011
I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies
View Related
Sep 5, 2011
I have a Cisco controller WLAN solution where I want to bridge traffic locally on a remote site, when using Cisco 1140 LWAPP.Is the only way H-REAP ?
View 3 Replies
View Related
Jun 30, 2012
I'm going through the CCNA training and I'm setting up my DHCP server on my 871 router. I have my cable modem into the WAN port on my router and have 1 host plugged directly into Fastethernet 1. I can ping any IP I want from the IOS prompt but I only have local access from the host. [code]
View 4 Replies
View Related
Mar 28, 2012
we are observing the no. of conn thru asa 5580 is getting increased and one a fine day it will stop sending/receiving traffics.firewall# show conn count 1900000 in use, 2000008 most used As per the datasheet of this asa, the max conns permissible is 2 million (20 lacs). and the output shows that currently 1900000 connections are there and 2million+8 connections are most used.when i run " show local-host | include host|count/limit ", below are the outputs showing for max connections..
local host: <172.x.x.x>,
TCP flow count/limit = 35857/unlimited
TCP embryonic count to host = 25
UDP flow count/limit = 0/unlimited
local host: <DC01>, TCP flow count/limit = 306/unlimited TCP embryonic count to host = 8 UDP flow count/limit = 736807/unlimited
local host: <DC02>, TCP flow count/limit = 246/unlimited TCP embryonic count to host = 2 UDP flow count/limit = 582010/unlimited
local host: <172.y.y.y>, TCP flow count/limit = 1/unlimited TCP embryonic count to host = 0 UDP flow count/limit = 308412/unlimited
These are the top 4 connections, i wonder should we consider only the tcp flow count or udp as well ?
View 4 Replies
View Related
Aug 26, 2012
I tried to ping from the "online host" PC to the outside,it succeeded. However, I can't ping from outside to the "online host" PC.
View 2 Replies
View Related
Apr 24, 2012
I test all devices using ping command, from ASA to router was fine (on both interface) but not to Host , and host to router was fine, but only on directly interface(F1/0), and to ASA was not success. am i miss something in my configuration?
View 5 Replies
View Related
Jul 6, 2011
configure my Cisco ASA5510 (asa version 8.3.1) so that one of the host (e.g.192.168.8.20) behind management interface can ping to the other host (e.g. 192.168.2.246) behind OUTSIDEinterface. I tried modifying the ACLs, NATs and ICMP statement, but still failed[CODE]
View 19 Replies
View Related
Jun 27, 2012
I have installed an Oracle DB (11.2) on a guest VM (Centos 5) and my host is Windows 7 Ultimate.I need to able to connect to the DB from windows.Ping status is as follows:
guest -> host - IP : Yes
guest -> host - hostname : Yes
guest -> guest - hostname : Yes
guest -> guest - IP : Yes
[code]....
View 5 Replies
View Related
Aug 7, 2011
I just purchased an E2500. I have a small home network dominated by Mac and Linux boxes, with an occassional Windows machine. On my previous router I had been running OpenWRT.
One of the nice features of DNSMASQ is that it will do local name resolution from the /etc/hosts file on the router. Is there anyway to turn on similar features in the E2500? I have a NAS box and a networked printer that require local name resolution. I had hoped that I could just create a DHCP reservation for them, and that the router would resolve their names for other hosts on the network. This does not appear to work.
Should I just be boxing this thing up and returning it in favor of a unit I can flash better firmware on to?
View 3 Replies
View Related
May 12, 2013
I have a cisco ASR 1002 I have plugged a host into an addressed port and the port comes up however the host cannot ping the router and the router cannot ping the host. Neither can router ping its self. I do the same on a cisco 2800 router and it works fine. What's goin on. Is it the fact that this is a ASR router ?
View 5 Replies
View Related
Nov 28, 2012
Version: Cisco ASA 5510 8.4(4)1
I've installed cisco asa 5510.
When I "show local-host all detail connection "
Normal situation:
105 myfailover:10.255.255.2/0 NP Identity Ifc:10.255.255.1/0,
idle 0s, uptime 1D14h, timeout 2m0s, bytes 18196822
But I got this output ( timeout - )
[URL]
View 0 Replies
View Related
Mar 3, 2013
I ran into a very interesting problem that occurred today and I'm trying to figure out why it happened. If it was one ASA 5505 that just required the reboot, then I'd have just chalked it up to a glitch, but when we built a new AD/ DNS server on the main network at the main site and changed the 3 Remote site ASAs to point to the new DNS server in the DHCPD options, none of them could ping any local host names to the DNS server at the main site they were now pointing too, but external host names { URL} all translated and pinged fine.
From a laptop on one of the remote sites, we could ping the new AD/DNS server(192.168.0.3) and the old AD/DNS server(192.168.0.2) and everything else at the main site, and telnet to port 53 showed successful across the Easy VPN from the Remote site to the new server at the main site. When wire shark was added to the new DNS server at the main site, the DNS request and replies for {URL}, for example, came and worked fine, but any requests for local resources never made it to the server from the remote sites.
A reboot of one of the Remote Site ASA's corrected the issue. Then I rebooted the other two remote site ASAs, and now DNS was working fine for everybody. I had also tried clearing the ARP cache on the ASAs before resorting to rebooting them. I also tried rebooting the laptop thinking the local DNS cache needed cleared before resorting to rebooting the ASAs. I'm struggling to understand why external, public host names made it through and resolved from the remote sites to the new server at the main site, but anything local failed before even reaching the new server(The new DNS server could resolve requests made by computers at the main site, but the remote sites that traverse the Easy VPN from the ASAs failed). The new AD/DNS server is the only server configured for DNS for all remote site computers.
Is any of this making sense? I'm wondering if clearing the x late or local host tables would have corrected it without having to reboot. I'm just trying to grasp the understanding here and figure out what happened.
View 5 Replies
View Related
Sep 29, 2012
I just try to ping a internal Host but it want to go.
Laptop<===>ASA5505
Connected is the Laptop at Ethernet 0/2 Inside
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
But If I try to ping to the Laptop I get the followed:
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
From the Laptop to the ASA5505 I can Ping successfully.
View 6 Replies
View Related
Aug 2, 2011
I have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12
???????????
100% lost
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
View 3 Replies
View Related
Apr 27, 2013
I have a single cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the the content Erp_IAT active it stops pinging. [code]
View 6 Replies
View Related
May 13, 2013
I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226". Is it because I used dynamic PAT for inside hosts?
interface GigabitEthernet0/0nameif outsidesecurity-level 0ip address 198.24.210.230 255.255.255.248!interface GigabitEthernet0/1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0
[Code].....
View 3 Replies
View Related
Apr 27, 2011
When I try to ping ipv6.xsnews.nl on either of my Windows 7 computers, it returns "Ping request could not find host". But when I do it on XP, it succeeds. I have tried putting the W7 PC in the DMZ, disabling the software firewall but it doesn't work.
What I think it involves is having ipv6 installed on each. I tried to duplicate the setup of both the XP and a W7 computer, installing the gogo6 tunnel. But apparently it's not setup on this computer because the ping result is the same as on the third computer which hasn't had ipv6 installed. s not setup on this computer because the ping result is the same as on the third computer which hasn
View 3 Replies
View Related
Apr 10, 2013
Basically after upgrade from ASA 8.4 to 9.0 (2) I have problems when certain types of NAT.Example:SA 8.4: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http while other ports can be accessed using the original IP (10.252.253.123).
ASA 9.0: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http but unlike before now I cannot access to the original IP (10.252.253.123) using another port or ping from host 192.168.3.2.
View 12 Replies
View Related
Feb 2, 2013
From the router I can ping the 2nd router, all its host and all of the 1941w interfaces.
From the 1941w AP i cannot reach the 2nd router or any of its host, but I can reach the interface that is connected to the 2nd router but only one side of it.
Attached are both my router and ap configs. At the moment I am just trying to reach the 2nd router and its host so I can update the AP IOS image but cannot reach the tftp server.
View 5 Replies
View Related
Apr 20, 2012
I am in a test environment using an ASA 55005 and a Cisoc 2611xm router. ASA is running version 8.4 and router is running is ios12.4. My VPN tunnel comes up but I am unable to ping between remote hosts. I used the ASDM and SDM for the configuration. Attached is a copy of both configs.
View 8 Replies
View Related
Apr 30, 2011
recently I had some malware on my Windows XP Professional (version 2002), so I followed a guide at Bleeping Computer [URL] to get rid of it. Problem is, for some reason, after I finished, I could no longer access the internet!When I try, FIrefox gives me their "could not connect" message: "Server not found. Firefox can't find the server at [site]." Check the address for typing errors such as ww.example.com instead of [URL]"When I try to log into MSN, the troubleshoot says I have a problem with my DNS and Key Ports.I'm not good with computers so I Google'd and found some ping-ing instructions. When I tried to ping [site], I get: "Ping request could not find host [site]. check the name and try again." This happens regardless of the site I use.Lastly, I tried "ping 127.0.0.1" from a troubleshooting site. It gives me: "Pinging 127.0.0.1 with 32 bytes of data:
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
[code]..
View 8 Replies
View Related
Feb 3, 2012
When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies
View Related
Mar 17, 2013
ping 10.0.0.1 -t give me destination host unreachable in the same time when i wright ping 192.168.1.1 -t it give me the correct reply but the net doesnt work
View 3 Replies
View Related
Oct 17, 2011
when do we get Desteination host Unreachable and time to live exceeded while trying to ping .
From 10.1.1.1 icmp_seq=2 Destination Host Unreachable
From 10.1.1.1 icmp_seq=4 Destination Host Unreachable
From 10.1.1.1 icmp_seq=7 Destination Host Unreachable
View 1 Replies
View Related
Sep 26, 2011
I've tried everything that has been posted so far except for opening up the router itself which I will refuse to do.- Getting = Host Unreachable 192.168.1.20 (I am using 192.168.1.1 as the gateway)- No ping whatsoever even when turning on the router over and over.
View 2 Replies
View Related
Mar 4, 2011
I am using the window server 2008 and configure tcp/ip properties correct ping locally reply successful when ping localy but when ping yahoo.com then reply destination host unreachable whereas gateway and dns ip is also correct configure so tell me solution about this problem because i am useing the internet.
View 1 Replies
View Related
Apr 23, 2011
i have configured remote access vpn on my 2801 router's gio0/0 int ip x.x.x.1. i connected my laptop through vpn client from internet. i connected successfully and my vpn router gives me the assigned ip block y.y.y.1. from my laptop i can ping the other int gio/1 ip z.z.z.1 but i cant ping the ip z.z.z.2 of my core sw which is connected on router's int gi0/1.
View 14 Replies
View Related
Jan 4, 2011
I have a cisco router 2811 connected on other two routers but can't ping any of them from any of them too (frame-relay encap correct) DLCI mapping ok all ip configured only router 2 's line protocol is up the rest is down on others and seems LMI sent are not receive and do know how correct that
View 1 Replies
View Related
May 21, 2011
I just installed a new ASA 5505 for an office with three internal subnets.* The three networks can each get online fine and ping eachother, but cannot browse to shares on the two internal networks other than their own.* How do I configure the ASA to allow all traffic between these three inside networks?
192.168.152.0
192.168.152.0
192.168.154.0
[code]....
View 8 Replies
View Related
