Cisco :: 5508 WLC Remote Access Points Are Not Registering

Apr 17, 2012

i have deployed WLC 5508 in head office with current 56 access points (mix of 1262N, 1141N and 1242) are regist ered and working fine, recently we extended to our remote office (connected over Layer 3 MPLS with OSPF Protocol) were none of the access points are not registering, i am able to reach to the controller from the specific VLAN and native VLAN without any issues. @remote site i have enabled option 43 and option 60 with the controller IP.
 
Number of APs.................................... 56
Global AP User Name.............................. ciscoGlobal AP Dot1x User Name........................ Not Configured

[Code]......

View 10 Replies


ADVERTISEMENT

Cisco Wireless :: Access Points Which Are Not Registering With WLC 2500

May 1, 2013

We have a couple of Access Points which are not registering with WLC 2500. I followed-up on the two LAPs in the dorm.  They were cycling through red, amber, green, indicating they were trying to join the controller but could not.
 
Recently, we have changed our IP Schema for the Wireless Devices and I believe there is an IP Conflict between APs and WLC. Earlier APs were cofigured with Static IP Address assignment, thus they can't change their IP Address.
 
how to reset the Access Point? I know we can hard reset them by pressing the Mode button manually.
 
Is there another way via which this can be done witout removing the Access Points from their enclosures?

View 7 Replies View Related

Cisco :: 5508 NCS 1.1 Not Showing Any Access Points

Jul 16, 2012

I have NCS 1.1 appliance and added a 5508 WLC running 6.0.199.4 code using snmpv3. Controller is added to NCS, but it doesnt show any AP's which are there on the controller. AP count is zero. I have another controller with code 7.0.230 added and showing AP's though. AP model is 1252.

View 5 Replies View Related

Cisco Wireless :: Push Access Points To Second 5508 Via HA

Aug 9, 2012

I am having an issue here.  I have 2x 5508 that each have 100 AP license and a little under 200 access points.  Basically all of the access points are using DNS to connect to the primary controller that has the DNS entry.  Basically half of my access points need to be on the second controller and in order to do this I have been using the high availability mode of each access point to push them to the second controller IP address.It was working perfectly until now.  I have pushed 28 access points to the second controller and the last two I need to push at this location just keep resetting on the primary controller.  Neither controller is configured as master controller.

View 4 Replies View Related

Cisco Wireless :: 5508 IP Scheme For Access Points

Jan 17, 2013

I have access points deployed across several buildings that each have a different IP scheme and their own T1 line. Is it possible to configure the 5508 controller to allow these access points to use the IP scheme assigned for that particular building or will dhcp always assign an IP address to the connecting client based on the IP scheme of the building that the controller resides in?

View 1 Replies View Related

Cisco Wireless :: Supported Access Points On WLC 5508

Jul 13, 2011

I need an official document from Cisco saying the APs models supported by the WLC 5508. Specially, I need to know if the AIR-AP1242AG-T-K9, converted from standalone, will be supported by the 5508.

View 1 Replies View Related

Configuring SSH - Cisco 3500 Access Points Under Wlc 5508

Jun 11, 2013

How to configure ssh in all access points ( cisco 3500 Access points ) under wlc 5508 ?

View 3 Replies View Related

Cisco Wireless :: To Implement WLC 5508 With 1262n Access Points

Mar 6, 2013

I would like to start setting up a Cisco Wireless Lan Controller 5508 with some Cisco 1262n AP's. How to start setting this to take advantage of having this wireless lan controller? I have a DHCP server, a Cisco 6509, and Cisco 3750g that connects the access points. I have Vlan 50 for wireless access points.

View 7 Replies View Related

Cisco Wireless :: 5508 / 1142 / Access Points Resetting?

Sep 2, 2010

Access points 1142 controller 5508 running code 6.0.196.0 When you set the access point port speed with "config ap duplex full speed 1000 all" the access points leave the controlle and do not rejoin. I have had to reset the the access points manually with a power down and hold the reset button.

View 13 Replies View Related

Cisco Wireless :: WLC 5508 Access Points No Load-balancing?

Mar 10, 2013

I'm having an issue in one open space area with a wifi network.I currently have 5 access points and around 100 users connected to the WiFi.There are desktops, Ipads and Mobile users connected to it.13,24,16,41,9 are the associated users to each access point. The one with 41 and 9 are only 10meters away from each other.
 
I read on some posts before having issues with APPLE and WIFI so cisco advised to disable the load balancing.I setup the client windown size to 10.On the networks the client roaming is with the default value.On the WLAN the Client Load Balancing is not checked.

View 4 Replies View Related

Cisco Wireless :: 3600 / 5508 - Access Points And Controller

Apr 11, 2013

We have an MPLS (layer 3) network 4 offices and a Data center. We are planning to install about 10 Access Points(3600 series) per office and have a controller(5508 series) in the Data center.
 
Questions:

1- Is this design possible, in other words, just one controller centralizing all Access point traffic in one controller in the Data center? 

2- We would like to accomplish this in two phases:
A- install access points without controller handling authentication thru Microsoft IAS servers (current configuration with 1200 series)
B- Deploy wireless Controller in Data center and start migrating orphan AP to Controllers one office at a time.

View 7 Replies View Related

Cisco Wireless :: 5508 - Broadcast SSID Only On Defined Access Points?

Jun 13, 2012

I'm using a Cisco Wireless LAN Controller 5508, 14x Access Points 1041 and 6x Access Points 1031 in combination with a NCS 1.0.
 
Is it possible to broadcast SSID'S only on defined Access Points, e.g. AP 1-3,7-10,18? If yes, what have I to do?

View 8 Replies View Related

Cisco Wireless :: New 5508 WLC And 3602i Access Points / Client De-authentication

Jan 25, 2013

Installed a new 5508 WLC last week, and finished bringing 68 new 3602i access points online in our College Dorms. We are seeing a lot of "Client De-authenticated" errors "Reason: Unspecified Reason: Code 1. Years ago I asked about error code 1. The reply from Cisco was: "The programers put the code in. It basically means we don't know what the problem is."Got a call from one of the dorms stating that students were getting knocked off the network while going to sites. If a student is wired, network is solid.Walked the dorm in question and was getting full bars of signals at all times, and was able to stream a movie from my Ultraviolet account without any break or slowdown as I moved from access point to access point. So.. my device, an iPad, was fully mobile and did not experience any disconnects.Did observe one student using a MacBook Pro. This student was constantly loosing connection to the access point. Checked the controller for the MAC of the student's computer. I did find deauthentication errors. BUT... this student's error was the computer was receiving an IP address from the DHCP that was already in use. At the computer the error message was a timeout issue.I am just learning the ropes on the 5508. Have used 3 4404s for the past six years.

View 2 Replies View Related

Cisco Wireless :: 5508 - Disable 802.11a On Certain Access Points Before Turning It Off On Controller

Apr 9, 2012

We are having 5508 controller with Lightweight access points 1142, IS it possible to disable 802.11a on certain access points before turning it off completely on the controllers?? Could you provide steps for doing so on WCS?

View 5 Replies View Related

Cisco Wireless :: 5508 - DHCP Option 43 For 1130 And 1300 Lightweight Access Points?

Mar 14, 2013

I have Cisco 1131 & 1300 Light Weight Acces Points and I have 5508 WLAN controller.  If i enable the wlan controller internal DHCP Server can this access points will work with this internal DHCP server or do i need to configure DHCP option 43 for these access points?  Can these access points works with LWAPP or do i need to configure CAPWAP?

View 4 Replies View Related

Cisco WAN :: 7965 Off Of Remote 881 Keeps Registering Throughout Day

Jun 7, 2012

A couple of our remote users are saying that during the day, suddenly their 7965 that hangs off their 881 will start registering for 3 to 5 seconds, then it will be fine.

View 8 Replies View Related

Cisco :: Air 3602i Not Registering With 5508 Controller

Mar 6, 2012

I can not get our 3602i AP's to register with our 5508 controller which is running 7.2.103.0 code.  We keep seeing an error in the log on the WLC   "AAA Authentication Failure for UserName:c46413c08e92  User Type: WLAN USER" and on the Access Point we are seeing [code]
 
I entered the CAPWAP ap controller ip address directly into the AP so it shouldn't be an option 43 DHCP issue

View 15 Replies View Related

Cisco Wireless :: Registering AP 3500 In Controller 5508

Apr 6, 2012

how an AP 3500 get to be registered in a controller 5508??, so, i have seen a lot of information of wireles deployment guide but i haven't understood yet how the process or flow is for getting the AP to be registered in a controller 5508, what exactly basic configuration must be done in a controller for doing it?

View 6 Replies View Related

D-Link DIR-655 :: Utilize RDP (Windows Remote Desktop) Between Two Points

Jun 10, 2013

I recently purchased (2) DIR-655 routers; one for home and one for the office. Both are connected to the 'net through CenturyLink DSL via a Zyxel 660 modem.I am switching from a Cisco/Linksys WRT54G home and a Trendnet TEW432BRP at the office. I wanted to get up to N and consolidate to a single hardware type. The 655 came highly recommended, and the price was right at $75.My goal is to utilize RDP (Windows Remote Desktop) between the two points and from other points inbound to either 655. The first hurdle was that the Xyxel modem, by default, blocks just about everything inbound with no hope of opening the ports. The only viable solution was to bridge the modem and allow the 655 to act as DHCP. Done. The modem now should not even have its own IP address, and should completely bypass all of the built-in firewalls, etc. As soon as I went into bridged and forwarded the ports in the router we were in business (though I still can't seem to log in to RDP, the ports are verified open).

View 6 Replies View Related

Linksys Access Point :: E4200 / E1500 - Cascading Routers Versus Access Points?

Nov 24, 2011

I am trying to find an effective way to extend the wireless signal across our home. I have tried various different solutions. Currently, I have an e4200 primary router that is cascaded with two additional e1500 routers that have been configured as access points. The Linksys support team hosted my computer and configured the devices. The e1500 routers are connected via ethernet wires running through the walls. And, this seems to be working well. Here's my question. The e1500 routers are configured with different SSID names, which Linksys advised was required to avoid conflicts in communications from the three router devices. Is there any way to configure this set up or something similar so that the entire wireless network has the same SSID and is seamless. In the current configuration, I have to specifically connect to the primary router or one of the two access points.

View 3 Replies View Related

Wifi Access Points With User Access Control?

Nov 27, 2012

We have a small office and already have a firewall in place that uses content filtering. I am looking for a low cost wireless access point that I can place behind my firewall that will allow me to control access by a username and password list, not just the passkey.

Does this exist without having to go to an Aruba or Ruckus type enterprise WIFI product?

View 1 Replies View Related

Guest Internet Access - Multiple Access Points?

Dec 13, 2012

Here is my setup:

Netgear WNDR3700 - Main router, DHCP turned on
4x Netgear WNR2000 - Setup as Access Points (DHCP turned off), connected to main router via LAN ports

I only want the guest network to have internet access. I have the guest network enabled on the router and access points with the option to "Allow Guest network to access main network" disabled. My problem is that since the access points aren't hooked directly to my modem via the WAN port, the guest network broadcasted from the access points does not have internet access.I have read up on setting up a separate subnet for the guest network using DD-WRT but was curious if there was a way to get the desired result with the stock Netgear firmware.

View 9 Replies View Related

1 CPU With 6 Access Points?

Mar 15, 2011

I am looking being able to control one computer at 6 stations. Each station will contain a keyboard, monitor, and mouse.They do not all need to be able to control or access the computer all at once. I would use a reverse kvm switch but I am looking at distances of 200-500ft between the stations/cpu.My last resort was to buy some cheap dells or build some low end computers and set up remote desktop but we would really like just having the keyboard, mouse and monitor.

View 10 Replies View Related

Access Points Going Default?

Feb 21, 2013

I have some network devices that are connected to a 110v power source that goes through a 110v/5v power converter.The Access points keep going back to factory default settings and losing their configuration. I have the same access points installed in the same situation but on a different site that work fine.have changed both the configuration and firmware to be be identical to the working Access Points and still the others default.They do not do this at a specific time of day and out of the 6, they do this at random and not at the same time. Sometimes they will go 24 hours + without defaulting, sometimes they'll go just 4 hours.

View 2 Replies View Related

Deleting Access Points From The Wii?

Dec 5, 2012

I would like to know how to delete a connection from my network. When I connect to the Wii it automatically chooses the right connection. What I have noticed though is that there is a third connection for a printer that is not secured and I have no idea why it is there or has an option to connect to the internet.

View 4 Replies View Related

Cisco ASA5505 And Wireless Access Points

May 31, 2011

We have a Cisco ASA5505 here that provides DHCP and routing to all our devices in our network. We also have a few other switches and wireless access points connected directly to the back of the ASA5505.For the past year all the wireless network signals has been working fine however starting last month, none of the wireless access points (we have three WRT54G) would allow proper connection (dropping connection, slow internet).I thought this maybe all THREE wireless access points are toast/bricked. So i went out and bought brand new Netgear WN604 and even with the new WAP i'm having same connectivity issues (really slow internet).When hardwired directly to the switches we get BLAZING fast internet & connectivity, no issues.

I called CISCO TAC and they automatically said "our ASA5505 is fine, it has to be your wireless access points" not working properly. I explained to them that i also purchased two brand new access points and they are doing the samething now, how can that be?

View 11 Replies View Related

Cisco :: Reboot Access Points Over WLC4404

Oct 3, 2012

We have two Cisco Wireless Controller 4404 with the IOS Version 7.0.220.0 and a lot of access points (ca. 170). Now i wan't to reboot a group of Access points where i found over a filter..Or how can i reboot all the Access Points at the same time over the Controller Interface? Is it possible? I only found the option in the WebGui where i can reboot 1 Access Point at the same time with "hardware reset".

View 5 Replies View Related

Cisco Wireless :: WAP4410N Access Points Set Up

Apr 9, 2013

I've had some long standing issues that I've tried various things to fix.  I have two WAP4410N access points set up at a smaller sister company.  Wireless clients (laptops) are not receiving DHCP assigned IP addresses.  If I type in an IP manually, it works fine.The sister company has a point to point T-1 connection to our main building.  Our main building has the DHCP server.  The router on the sister company end is configured as the DHCP relay. 
 
I've upgraded the firmware three different times in the past to hopefully resolve the issue, but no luck.  Just today, on one of the WAP4410N's, I upgraded to the 2.0.6.1 firmware (backing up config, reset to factory default, upgraded firmware, reset factory default again, restored config).  After the first reset to factory defaults, the Access Point itself picked up a DHCP address from the server, and I verified this in the DHCP console on the server, so I know that the DHCP relay is working.  However, my laptop would not get a DHCP address when connecting wirelessly through that access point.  It is a Windows 7 Enterprise laptop.  I also could not get a DHCP IP with my iPhone connecting to wireless, to rule out specific issues with just a laptop.I have the DHCP lease times for the subnet that these WAP4410Ns are on set to 2 hours.
 
To put a cherry on top, there is one laptop that stays in a lab area at all times, connecting wirelessly, and it DOES get a DHCP IP address (I can see in the DHCP console that the lease for this laptop continually renews as needed).  I do remember on initial config when I couldn't get it to work, that I did a manual set up, gained connection, then switched it to DHCP...but that doesn't work for any other laptop.Why would the access points get DHCP address, but not anything connecting to the Access Points?

View 5 Replies View Related

Cisco Routers :: 800 - Replace Access Points

May 22, 2013

We have the following connection based in the services provided by our local telephone company, the connection arrives to a router Cisco 800 series. From the router, i send it connection to a switch SRW2024 v1.2 (Business series) 24-Port 10/100/1000 Gigabit Switch with webview. That switch is useful to send connection via RJ45 for a few of PCs. Then, I send connection to a switch SRW2008P (Business series) 8-port 10/100/1000 Gigabits with vieweb and power over ethernet. The last switch, send the signal via RJ45 to seven WAP2000 (business series) Wireless-G AP with PoE.
 
That network is running fine, but I've some problems to cover some areas within the building and sometimes the signal is really poor. The cable RJ45 between the PoE switch and each AP is no longer than 50 meters and each one with antennes about 8 or 9 Db.

So, now I've the possibility to change the access point for a power devices.

View 1 Replies View Related

Cisco Wireless :: CDP On Access Points 3502 Aps

Mar 15, 2012

Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs.  But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.

Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?

View 6 Replies View Related

Wireless :: Change Between Access Points?

Aug 30, 2012

At my school we have a lot of access points, but sometimes the computer use the wrong access point. How can I solve that? Is there a program for switching access point?

View 8 Replies View Related

Home Hub - Add Wireless Access Points?

Nov 10, 2011

BTW the halls are next to each other.The house and the 3 halls are in the vicinity however not attached together(i.e. wall to wall). The distance between the house and the first hall is approx 1 road width distance.ISP is Virgin and the internet was installed this year hence has the latest Virgin Home Hub.I am aware that i probably require 3 wireless access points (1 for each hall).The first wireless access point will need to be connected with a RJ-45 cable running from Home Hub. Can i connect the Wireless access points up together or do they all need to come from the ADSL hub?I am not sure what Wireless access points would be best and how to go about connecting this all up

View 2 Replies View Related

Two Wireless Access Points With Two Routers?

Jul 5, 2012

I have New Pace 4111n Wireless Router that I got from AT&T and is setup on 1st floor, but its wireless range does not get me to 2nd floor. I also have the 2Wire wireless router from AT&T. In Addition, I have ethernet connection from level 1 to level 2 as well.

I was wondering if it is possible to have the Pace Wireless N router to work as modem and wireless access point, at the time use the 2Wire router to broadcast wireless and act as access point for 2nd floor.

IF its doable, how should the two be configured and connected.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved