Cisco :: 7.0.172 / Manual Backup The Location Appliance?

Jun 19, 2011

I upgraded wcs to version 7.0.172 and migrated it to new server and ip address. The upgrade was done by install wcs 7.0.172 on new server and restoring a backup. I also upgraded the location appliance from 6.0.101.0 to 6.0.202.0. The wcs can see the location appliance without a problem. The problem occurs when i try to backup the location appliance. The wcs appears to run the backup and completes with a success but i cannot find the backup file in the ftp directory. wcs backup to ftp folder is fine.is a there a way of doing a manual backup the location appliance what logs can i check to see whether the backup is taking place or not?

View 2 Replies


ADVERTISEMENT

Cisco Wireless :: Location Appliance 2700 Compatible With WCS 7.0.164.3?

Jan 15, 2012

I have two Cisco Location Appliances 2700 devices that has version 6.0.101.0 on. I'm having problems getting it to work. Any that can assist with this?

View 1 Replies View Related

Cisco Wireless :: Location Appliance 2700 - Is It Supported With V7 WCS And WLC

Aug 9, 2011

The compatibility matrix shows no support for a Location Appliance 2700 for any version 7.0.x.x for WCS and WLC. However, I did see a thread here where a v6.0.x.0 had compatibility. v6.0.202.0 is MD. Is it compatible with v7 WCS and WLC?

View 3 Replies View Related

Cisco :: LMS Prime 4.1 Soft Appliance Backup

Jan 17, 2012

We have an installation of Cisco Prime LMS 4.1 soft appliance on VMware and i would like to ask if it is possible to backup the database on an external drive other than the 'local' LMS hard disk.

View 3 Replies View Related

Cisco :: Backup Space In LMS 4.2 Soft Appliance?

Oct 15, 2012

LMS 4.2 Soft Apliance has default:
 
Filesystem            Size  Used Avail Use% Mounted on
/dev/mapper/smosvg-optvol
105G  4.8G   95G   5% /opt
/dev/mapper/smosvg-varvol
53G  268M   50G   1% /var
 
Where to create Backup folder? Under /opt or /var ?

View 3 Replies View Related

AAA/Identity/Nac :: Windows ACS 4.2.0 Backup Database On 1120 Appliance 4.2.1.15?

Apr 26, 2011

I am running windows based acs 3.3 in my lan environment going to be replaced with acs 1120 appliance running acs 4.2.1.15 , ACS 3.3 database has been built upto  4.2.0.124 ,step by step by upgrade process
 
1) acs 3.3.3.14---> 4.1.1.24
2) acs 4.1.1.24 ----> 4.2.0.124 .
 
now my database is with 4.2.0.124 dmp file , I cannot upgrade my database to 4.2.1.15 because 4.2.1.15 patch is not applicable & executable  on 90 days evalution package of 4.2.0.124 of windows platform .
 
can i import my windows based 4.2.0.124 datbase directly to my acs appliance running 4.2.1.15.3 ??? , else its requires any step to be done to modify the windows based databse matching to appliance windows verison once .
 
I could see on appliance under restore settings the following options (restore from 4.2.0 backup file to acs 4.2.1)

View 8 Replies View Related

Cisco :: Prime LMS 4.2 Soft Appliance Vmware Server Backup

Jun 13, 2012

I have to install Prime LMS 4.2 on ESX customer infrastructure (ova image as soft appliance). The customer  would like to know if LMS 4.2 is compatible with his backup agents  :

* Symantec Veritas Netbackup (v7.1.0.2)
* Control-m (v6.4.01.300)

If not, what would be the best solution to backup the server ? Are the VMware tools supported now ?

View 1 Replies View Related

Cisco Wireless :: 2700 Wireless Location Appliance Compatible With 2500

Feb 12, 2013

We plan on buying a Cisco 2700 wireless location appliance but I need to know if it will be compatible with our 2500 WLC.I've tried to look but cant find any document for this. Also can you deploy the location appliance without a WCS?

View 7 Replies View Related

Cisco Application :: ACE4710 Appliance To ANM Virtual Appliance NATed

Oct 12, 2011

We have an ACE Appliance in a DMZ and the ACE Appliance's Admin Context IP is translated between ACE and ANM. The ANM Server does not get translated. It is just the opposite then in another Community discussion.
 
Our Problem: When adding the ACE4710 Appliance to the ANM imported Device List, we use the ACE's NATed Admin Context IP. Import works well, but ANM reflects the Admin Context IP with it's real configured IP. Polling the ACE Appliance does not work therefore.
 
Is there a possibility of telling the ANM, that the ACE has to be polled through a NATed IP? I could not find a field to set a NATed Mgmt IP.
 
Configured IP on ACE Admin Context: 192.168.0.10
NATed ACE Admin  Context IP:           172.16.0.10
 
Imported ACE with IP 172.16.0.10 into ANM, but ANM polls for Rserver, Vserver, Probes, etc. via 192.168.0.10 - which is not reachable from the ANM.

View 2 Replies View Related

Cisco Wireless :: SG-300-52 User Manual?

Jun 25, 2011

Where can I download the user manaul for this switch, not the quick start guide?

View 1 Replies View Related

Cisco WAN :: PAT Configuration With Manual IP In 2921

Sep 27, 2012

I am having a public IP address and it is not configured on any of the router interface on my Cisco router. I am having 3 internal networks. Is there any way to PAT all these 3 internal networks to this public IP?

View 3 Replies View Related

Cannot Use Manual IP Setting Through Switch

Oct 23, 2012

We have modem router 4-port with IP range 10.0.0.1 - 30 setting.one port goes to a library where we have a 8-port switch STLAB SWHUB-8p serving 2 pc with auto IP setting (internet works fine)and one port goes to another corner of the library to a switch TP-LINK TL-SF1008D V4.1 .4 pc are connected and a printer all are set with manual IP in an active rang of the router 10.0.0.10 - 14 they have to be on manual IP becuse of the ptinter.they cannot connect to the internet but I get the message connected.If I change them to auto IP - they can connect to the internet, the router gives them an IP.

View 3 Replies View Related

Cisco Switching/Routing :: 881 - Manual Binding Mac To IP?

Feb 8, 2013

I am trying to bind Mac address manually to IP in Cisco 881 router so that if user wants to change the IP address also they should get the same IP.
 
I have configured as below but it is not working.
 
ip dhcp pool Test
host 192.168.0.10 255.255.255.0
hardware-address xxxx.xxxx.xxxx.xxxx
 
this IP was excluded from dhcp range
 
ip dhcp excluded-address 192.168.0.10

View 11 Replies View Related

Cisco Routers :: WRVS4400N VPN Needs Manual Connection?

May 8, 2013

WRVS4400N needs to be manually connected when the power is recycled after power failure. Is there a setting to connect an IPSEC VPN automatically, instead of manually going in to connect the VPN

View 3 Replies View Related

Wireless :: Prolink H5305g Manual PDF?

Mar 22, 2011

I am looking for Prolink H5305g manual in PDF.

View 1 Replies View Related

Computer IP Changing To Manual When Set On Automatic?

May 2, 2011

what I did do was manually set my IP address for my laptop for my wireless. But I no longer needed to do that so I set it back to Automatic. But every minute or so my IP is changing back to 192.168.0.12 which I did change it to, although it is on Automatic. This is my guess to as what it is doing as I have no connection to the internet after about a minute. ipconfig also displays my IP Address as being 192.168.0.12 as well.What I have to do is disable and then reenable my wireless to get it working again.

View 14 Replies View Related

Find Out Who Have Manual Ip When Addresses Reserved?

Jun 11, 2011

We have reserved ip addresses for all computers in our DHCP server. But sometimes we notice that some of our staffs put manual ip in their computer and so far I have no idea how to trace it from server itself without visiting each computer to check it out.

View 3 Replies View Related

Get A Manual In English For Experia Box Zte H220n?

May 3, 2012

I would like to get a manual in English for the experia box zte h220n.

View 1 Replies View Related

Cisco Switches :: Manual Multicast ARP Entry For SG300

Jan 22, 2012

We're replacing our older catalyst switches with new SG300 family switches and have a Microsoft NLB cluster for some services that run in multicast balancer mode.
 
We currently do L3 routing to the network with the cluster and have the following IOS configuration line in the specific switch to let users on other subnets to access the services.
 
arp 10.20.1.226 03bf.0a14.01e2 ARPA
 
How do we replicate this using the SG300 series in L3 mode? Whenever I try to add a manual ARP entry I get an error message that says that the MAC address is not a valid unicast address?

View 4 Replies View Related

Cisco Wireless :: AIR-ACCRMK1300 Mounting Manual Required

Jul 30, 2012

I need some manual about how to use AIR-ACCRMK1300=.Is there any offical manual?

View 4 Replies View Related

Cisco :: 1500 LMS4 Manual Device Discovery

Nov 7, 2011

I have a very special usecase with migrating devices from LMSv2.6 to v4.1 using DCR bulk import that was maintained manualy, not by discovering.The special thing is each device has its own SNMP-community and its about 1500 devices.RME discovery works fine, but I get the devices not discovered by DCR (CSDiscovery), because I need a minimal DCR discovery configration containing Seed and SNMP-settings. So I activated DCR as seed, but cant skip SNMP settings without an entry. But in this case I would need 1500 SNMP-lines that would be very unhandy. is in CSDiscovery-Settings a possibility to can leave SNMP settings untouched so it takes the credentials from the DCR, to can start DCR discovery?

View 6 Replies View Related

Cisco Firewall :: How To Configure 6 To 4 Manual Tunnel On ASA5585

Jul 6, 2012

I have ASA5585 Firewall between my WAN Cloud and LAN Network. I plan to configure Layer 3 Vlan Interfaces inside FW and it would be Layer 3 gateway for some of Subnets. Layer 3 VLAN Interfaces are planned to be dual stack containing both IPv4 and IPv6 Address stack.
 
I plan to configure 6 to 4 Tunnel with my Hub Site where we have native Ipv6 awareness. One tunnel end point would be ASA and the other endpoint would be Hub site WAN Router/L3 Switch. So IPv6 traffic hitting to vlan interfaces on ASA  would be policy checked and routed over tunnel interface to Hub Site.
 
6to4 Tunnel manual tunnel configuration on ASA. I have configured such tunnel on L3 Switch or Router with following config.
 
Int tunnel xyz
  ipv6 address  <ipv6 address>
  ipv6 enable
  tunnel source <loopback address of my L3 Switch>
  tunnel destination <loopback address of my hus site L3 Switch/Router>
  tunnel mode ipv6ip
end
 
I need to implement something similar in ASA. How can I do that?

View 2 Replies View Related

Can't Connect To Network Without Manual Ipv4 Settings

Jun 13, 2012

A few months back, my computer stopped connecting to networks. Through some process or another, I ended up "fixing" it by manually inserting the ipv4 settings. Apparently that only allows it to connect to my router though, as public wi fi won't work for it. If I leave the ipv4 settings set to automatically obtain information, the computer won't connect to the network. It will stay on the "identifying network" part indefinitely. In addition, I can't connect through the modem directly either, manual settings or not.

Here is the ipconfig while ipv4 is in auto-obtain

Windows IP Configuration
Host Name . . . . . . . . . . . . : Home
Primary Dns Suffix . . . . . . . :

[Code].....

View 14 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3220 Manual APN Settings

Mar 14, 2013

Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
Region : Others

I have MR3220 version 2 and HUAWEI E398 stick.It connects to 3G/4G network, but with wrong APN.It seems to me that manualy changed APN can not be applied. [code]

View 4 Replies View Related

Cisco Routers :: RV082 Fails To Respond Until Manual Restart

Nov 3, 2012

I've been noticing that occasionally our 2nd Gen RV082 fails to allow internal admin management until a manual restart.  After the restart, all seems to be fine and traffic/router is very responsive. The following describes typically how the issue occurs: Internet traffic is rather slow and unresponsiveContent is failing to load for end usersWebsite are loading but with images or css failing to loadWebsites fail to load and appear offline (not all, but some such as ebay for example)We recognize there is a problem, let's try to access the local router adminFails to load the log-in prompt, so we manually reboot the deviceAll is operational for now We are running Firmware Version: 2.0.0.19-tm.  [URL]

View 2 Replies View Related

Cisco :: LMS 3.2 - Reboot Requires Manual Start Of TomcatMon And Apache

Feb 24, 2012

I have taken over a couple of LMS 3.2.0 standalone servers (two different networks). When I reboot them they tend to be slow coming back up (20-30 min). I"m thinking this may be due to the fact that LMS was reinstalled on both of them as I see an old CSCOpx folder (CSCOpx_old) as well as the current one. I assume that someone reinstalled and the registry may be dirty and service dependencies may be jacked up but honestly I don't know how this works for LMS and I haven't found much good info in the user guide for common services for service dependencies or registry keys in general.
 
Also, one of the servers never comes up fully on reboot or restart of the daemon manager. I troubleshot this and found that Tomcatmonitor and Apache are always down after reboot/restart. Tomcatmonitor says that it was shutdown by the administor in a pdshow and Apache says that it was never started.  I have to go into the server and manually start these processes with a pdexec to get the application up.

View 1 Replies View Related

Cisco Switching/Routing :: 2960 - Manual Ip Binding In DHCP

Nov 27, 2011

WE HAVE cISCO 2960 SWITCHES. this switch acts as a dhcp server for the hosts connected to it. Provided mac based binding to the hosts, with enabled dhcp snooping and IP source guard per interface.' I have a problem with single host couldnt get an ip from dhcp as he binded based on mac: manualip. Here is my config: We have a VLAN99, 70 hosts connected should get an ip based on mac
 
switch(2960<config>interface vlan99
# ip address 10.10.14.2 255.255.255.0(code)

The above host amit (10.10.14.31 swhould get this ip bindded with mac) but hez not getting manual ip i.e 10.10.14.31, but if an ip excluded from the dhcp free, he can get that ip i.e automatic ip . every other host are getting the ips as binded in the pool manual ip. Checked with

**sh mac-address table dynamic vlan 99   ()
**clear ip dhcp binding *   or  10.10.14.31
** clear ip dhcp snooping binding
*** clear ip dhcp conflict *

Tried to change pool names. All these troubleshoot couldn't make me success in providing amit an manual ip.

View 10 Replies View Related

Buffalo WHR-G300N Router - Automatic DHCP To Manual

Oct 12, 2012

I have a Buffalo WHR-G300N router & I am having probs with assigning a static address to a nas device.I have set up the static ip address i want to use in the nas When I look at the dhcp leases in the router, the device shows up as having an automatic assignment with a different ip address to the one set in the nas.If I manually assign the ip address which I want to use, or, if I edit the automatically assigned entry, the old one stays as an automatic assignment. This means that I then have 2 ip addresses for 1 mac address.When I try to access the nas, with only the automatically assigned address present in the router settings, I can still access it using the ip address I have manually assigned to the nas, even though the manual ip does not show in the router.How can I delete the automatically assigned dhcp lease & just keep my static one??

View 2 Replies View Related

Belkin Hi Speed Wifi G Router - Always Needs Manual Dns Change

Oct 12, 2011

I've been having this problem with my Belkin router since day 1 when i got it.( not new, got from buddy's place) It's Belkin HI Speed Wifi G router, and what's really frustrating is, everytime i connect to it, I need to manually change the DNS address and switch between 4.2.2.2 & 4.2.2.4 in order to get internet access! Sometimes it even cuts off the internet during a session, without me even disconnecting from the wifi network, where I would again need to switch back and forth to the 2 or 4 ending!

View 3 Replies View Related

Acer Laptop 5733Z Aspire User Manual?

Oct 18, 2011

I don't think I ever set up my laptop for home WIFI. There is only one choice, (being Belkin) in Home Group and would like to take my puter to another room in my house using my WIFI modem occasionally. It did work fantastic at a friends house hooking up to their WIFI. I have been looking for a manual to download, but can't seem to find one on line or at the Acer home page.

View 1 Replies View Related

Western Digital Wd Livewire Powerline Av Network Kit Manual

Feb 8, 2013

Western digital wd livewire powerline av network kit manual?

View 1 Replies View Related

Home Network :: Create A Manual Route Into Laptop

Jun 6, 2012

My laptop have 2 NIC attach it, the cable NIC and Wireless NIC, the cable one connect to my lab network environment and the Wireless connect to office network environment (connect to internet) which both have differen segments [code] when my Wireless was turn off my pc can ping to all segment on my lab network environment, but if the wireless was turn on, i cant ping to others segment but only my laptop segment and i still could surfing to the internet without any problem.then i tried to add a new route from my laptop using "route add x.x.x.x mask x.x.x.x (gateway)" in command line and after that i can ping back to all segment in my lab network environment eventhough my wireless was onwhy i have to create a manual route into my laptop so that i can have connection between my laptop and my lab environment in the condition my wireless turn on ??

View 8 Replies View Related

D-Link DCS-942L :: IR Lights Stay On In Manual Mode

Mar 29, 2013

I was trying to set this up pointed out a back window, but obviously ran into the IR lights reflecting back on the glass.  I don't have an external IR light yet, but just tried the manual IR mode and the IR lights stay on.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved