Cisco :: 7606-s / Snmpwalk Gives Timeout Error - Ciscoworks
Sep 17, 2012
I used the below syntax to check the snmpwalk to an interface of a cisco 7606-s router from an LMS 4.0 version cli.
NMSROOT/Objects/jt/bin>snmpwalk -v 2c -c <snmp-string> <ip-addr> 1.3.6.1.2.1.31.1.1.1.6
Timeout no response from <ip_address>
This is the error im getting in cli prompt. But i could see that reports are generating.If i try with the loopback ip address, i get proper snmpwalk outputs.. I have increased the timeout and retry options..
View 3 Replies
ADVERTISEMENT
Nov 24, 2012
I upgraded CiscoWorks LMS from 3.0 to 3.2 today. Everything worked prior to the upgrade.The upgrade was successful, with no errors, and all services started. check everything and I see no problem. The system creates the file MDCSupportInformation.zip me clean without any content.I add the installation log file;And tell them that after upgrading to 3.2, you carge the following patches:
LMS321-win-CSCtr77570-0.zip,
cm5.2.1-nt-CSCtw88763-1.0.zip,
lms3.2.1-win-CSCts95764-0.zip,
lms3.2.1-win-CSCts82530-0.zip
in that order.He added the logs generated by the LMS services Tomcat and Apache
View 4 Replies
View Related
May 29, 2010
I have a Cisco 3945 Router and when we try to add the same into the Cisco Works it gives me an error saying " CM0056 Config fetch failed for 192.168.xx.xx Cause: CM0204 Could not create DeviceContext for 1238 Cause: CM0206 Could not get the config transport implementation for 192.168.xx.xx Cause: UNKNOWN Action: Check if required device packages are available in RME. Action: Check if protocol is supported by device and required device package is installed.
We are using LMS version 2.6. Any info on the latest router 3945 with support or not.
View 6 Replies
View Related
Jan 15, 2012
I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.
================ Snipped from crashinfo file =================
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0
05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
==================== Show Version ======================
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 10-Feb-11 19:27 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
[Code]...
View 3 Replies
View Related
Aug 14, 2011
Whenever I tried to do backup of CiscoWorks from GUI, I am receiving a error message"Backup failed. ERROR(292): C:PROGRA~1CSCOpx/backup.LOCK file exists, look into the log file C:/PROGRA~1/XCSCOpx/log/dbbackup.log for more details". backup.LOCK file size is 0KB.I am using LMS 3.2; RME 4.3.0;CM 5.2.0
View 1 Replies
View Related
Jul 3, 2012
When I try to access Gizmo's Freeware | Find the best freeware fast, I'm getting timeout errors. I tried using different browsers but got the same result. All other websites loads fine in my browsers.I checked Down For Everyone Or Just Me -> Check if your website is down or up? and found that it's just me who's facing this problem.I also did a "tracert" from command prompt and got request timed out in the 19th hop at 209.59.157.128[CODE]
View 2 Replies
View Related
May 8, 2013
i have this message "DHCP Timeout"on few cisco IP Phones . try to assign IP manually and it's working fine.. seems DHCP not giving IP's to those.. 6500 have configured as DHCP pool.
View 3 Replies
View Related
Apr 27, 2013
There is a cisco ws-c6509,recently it appear error log “%FABRIC-SP-6-TIMEOUT_ERR: Fabric in slot 5 reported timeout error for channel 11 (Module 3, fabric connection 1)”. When I reload the device,the error log disappear.But a few days later,it appears again.I try to replace the slot 3 (WS-X6704-10GE),the error log continues.The IOS version is 's72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF8"
View 1 Replies
View Related
Nov 1, 2012
I got this error this operation returned because the timeout period expired error code 0x000005b4
View 1 Replies
View Related
Nov 26, 2012
ASA 8.2(5), uauth absolute timeout is disabled and inactivity timeout is set to 48 hours:
timeout xlate 48:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:00:00 absolute uauth 48:00:00 inactivity
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
Users still get kicked out every 8 hours and they have to reauth. This is a logging message:
%ASA-5-109012: Authen Session End: user 'john', sid 839, elapsed 28801 seconds
View 1 Replies
View Related
Dec 6, 2011
I need to create a policy to provide only 4 Mbps bandwidth for mail out of 16 mbps pipe terminated on 7606 router (at Datacenter) having WS-SUP32-GE-3B.But I can't create policy with bandwidth percent,even exact value with priority command does not work. When I am going to enter service policy output command at interface it is showing as"priority command is not supported in output direction for this interface Configuration failed!" All I want to restrict bandwidth at backbone link for mail traffic. From all remote locations use to access mail server over the same link.
View 1 Replies
View Related
Apr 18, 2011
high CPU on newly installed 7606.
CPU utilization for five seconds: 61%/59%; one minute: 62%; five minutes: 63% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 578 5856 9392486 0 0.55% 0.50% 0.50% 0 IP SLAs XOS Even 231 90364 576908
[Code]......
View 1 Replies
View Related
Jan 18, 2013
I tried to reboot manually and I changed the slot but the same behavior:
%SYS-SP-3-LOGGER_FLUSHING: Systema pausing to ensure console debugging output
%OIR-SP-6-CONSOLE: Changin console ownership to route processor
*** System received a Software forced crash ***
signal= 0x17, code= 0x24, context= 0x430213e4
PC = 0x4038c124, Cause = 0x1020, Status Reg = 0x34008102
View 1 Replies
View Related
Mar 5, 2012
who to configure the interface of cisco 7606 router. As it is not getting up by doing normal configuration like "no shut"? iterface and line protocol both are down.
View 1 Replies
View Related
Sep 28, 2012
Our Router 7606 is in a problem with high CPU Utilization. We are using one EBGP and one IBGP session. We are also running OSPF with area 0 between two IBGP router to exchange few local networks. When bandwidth cross 100 MB than only CPU use become 100%. when bandwidth consumption is 80MB CPU use become 80% end so on.
Out put is when bandwidth consumption is 34MB
CPU utilization for five seconds: 44%/43%; one minute: 42%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
78 44 9625 4 0.39% 0.03% 0.00% 2 Virtual Exec
13 40 375 106 0.07% 0.00% 0.00% 0 ARP Input
30 116 1098 105 0.07% 0.01% 0.00% 0 IPC Seat Manager
[code]....
View 27 Replies
View Related
Sep 18, 2012
I have a fresh piece of 7606-S router, i am planning to install a new IOS ( 15.2.4S or 12.2.33-SRD8 ) SIP-200 / RSP720 moduls ... would ypu plese provides me a configuration guide for installing IOS for 7600 serise router.I have the image on TFTP server.
View 3 Replies
View Related
May 1, 2012
I have an Internet Gateway with dual homed to 2 ISP's terminated in 2 different routers in my end. My end routers are 7606 routers.
I have a WAN link from Router 1 to ISP1 and from Router 2 to ISP2.
Router 1:
-------------
int Gi1/1
description " Link to ISP1"
ip address x.x.x.142 255.255.255.252
x.x.x.141 is configured in ISP end router.
The problem I m facing is that I m not able to ping x.x.x.142 from this router. But x.x.x.141 is pingable.
Also when I check from any internet route server, I m able to ping both x.x.x.142 and x.x.x.141.
View 1 Replies
View Related
Mar 18, 2011
I was trying to install a SPA-IPSEC-2G on 7606-S chassis. I installed the SPI/SPA cards in slot 3, after that I checked with "sh module" and we could see the module "OK". After this we tried to configure a VPN tunnel but we received messages in the other router about "no ipsec package".
I was checking and I tried "sh crypto engine accelerator statistic" and we got the message: " There is no crypto device".
I don't know about installation commands in references and I don't know about restrictions or configuration modes.
View 3 Replies
View Related
Jul 19, 2011
I have a 7606 router with sup 720-3bxl. IOS has been crashed recently and i can use only Roman mode now. Ive tried to upload ios image using tftp server but the command tftpdnld id not available in this router. I don't know why. Then i tried to boot from flash disk but finally it also shows an error like
System received a Software forced crash signal= 0x17, code= 0x24, context= 0x42359674 PC = 0x402d248c, Cause = 0x1020, Status Reg = 0x34008002
How to make the router in running condition.
View 3 Replies
View Related
Apr 16, 2011
We have 7606 router without any ipsec module on it,so i check the ios and it has all commands in interface tunnel for configuring the dmvpn multipoint tunnel and also protection profile for ipsec! so i have this question: do we can run dmvpn between this router and our wan routers wich are 3845.
View 2 Replies
View Related
Mar 5, 2012
I've setup and configured the following local monitor session on a 7606 but it doesnt seem to be outputing anything. Any guess as to why, or what I might be doing wrong? Gi1/1 is doing ~40Mb/s egress & 15Mb/s ingress. Both source and destination ports are routed ports.
monitor session 10 source interface Gi1/1
monitor session 10 destination interface Gi1/10 ingress
interface GigabitEthernet1/1
description WAN Link to ********************* ** CORE BACKBONE **
mtu 9000
ip address ************** 255.255.255.252
[code].....
View 1 Replies
View Related
Nov 10, 2011
I need to put a FWSM and a line card WS-X6148A-GE-TX to a router 7606. The FWSM version is 3.2(13). The router is running IOS 12.1(18)SXD3. The Cisco document here says the required IOS for router 7606 is 12.2(18)SXF or higher. I have downloaded the IOS 12.2(33)SRD4 and loaded it to the flash card. When I turn the router on, it doesn't load the new IOS and goes to rommon. Which IOS I should use to make the router 7606 work and accept the FWSM.
View 2 Replies
View Related
Jun 5, 2012
We are planning to configure the ipv6 PBR on our 7606 routers. We have configured the route-maps successfully .but when we tried to apply those on interfaces we are facing an problem .
when we trying to give command # ipv6 policy route-map <route map name> . we are unable to find policy command option in the command list.
IOS Version : c7600rsp72043-advipservicesk9-mz.122-33.SRE3.bin.
View 1 Replies
View Related
Nov 5, 2012
We have an environment where we terminate our DSL customers over PPPoE on a 7606-S MPLS PE router with RSP720. The PPPoE sessions are terminated on a GIG V2 interface of a SIP-400. Currently the IOS running on the device is c7600rsp72043_rp-ADVIPSERVICESK9-M, Version 12.2(33)SRD. The following is the current configuration used.
bba-group pppoe 7virtual-template 7
interface GigabitEthernet2/1/3.142647 accessencapsulation dot1Q 14 second-dot1q 2647pppoe enable group 7
interface Virtual-Template7 ip vrf forwarding TESTip address 10.10.10.1 255.255.255.252
In the above scenario everything works well.
However we had to upgrade the router IOS to 15.2(4)S Advance IPServicesk9 to support 4-byte ASN. After the upgrading we observed certain commands used to terminate PPPoE on the sub-interfaces not available on 15.2(4)S , although PPPoE on Gig and Ethernet with QinQ support is listed under 15.2S feature set.
View 1 Replies
View Related
Jul 13, 2011
At present we are using the Ciscoworks LMS bunde 3.0. I would like to upgrade to LMS 3.1.
My Question: Is it possible to upgrade to LMS 3.1 with using the existing LMS 3.0 license.
View 2 Replies
View Related
Jan 17, 2013
I have two Cisco 7606 routers using BGP to connect our customers to the internet. Recently we added a new 1G circuit in addition to an existing 1G circuit and all traffic inbound is now on this new 1G circuit. We would like to shift some of the inbound traffic over to the other 7606. Our Tier provider has the same AS number for both paths. One path goes directly to New York and the other goes to Boston then New York.
View 1 Replies
View Related
Sep 15, 2012
I have a 7606 Router with single Route Switch Processor 720 at the chassis works as active RP ( Route Processor ). Can I add another RP to the chassis as standby in case of failure of the first RP ?
View 28 Replies
View Related
Sep 29, 2012
I have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking about the procedure?
-shall i switch off the router ? or just removeSUP32 and insert RSP720 ?
-are there any steps should i do before the upgrade ?
-i am planning to take the router out of service during the operation, how much down time it will be ?
View 4 Replies
View Related
Aug 31, 2011
There was a interface down in one of critical devices in the network.that particular log is not captured by the ciscoworks(DFM-alerts).
View 1 Replies
View Related
Oct 24, 2012
I am trying to get CiscoWorks LMS 4.0 to connect to my routers in order to back up configurations, but I am getting SSH authentication failures reported in the router logs (and archiving fails).
The credentials LMS is using is a username and password with priviledge 15: the account is established in TACACS+. I can log into the devices directly with this user account.However, I cannot TFTP from the routers to the LMS either (I get a permission denied message in the router).
LMS did manage to fetch some configs, but 90% of my devices are having this issue.
View 4 Replies
View Related
Sep 11, 2011
I need download LMS 4.0 eval trial. But i can't see any link down on url...
View 1 Replies
View Related
Oct 23, 2011
I upgraded the LMS 4.0 with LMS 4.0.1 but now the events are removed of Fault View. The equipments than I am monitoring are: ME-3600, ME-3800 and ASR 9000. This is a configuration problem or I have to update something else?
View 1 Replies
View Related
Jul 10, 2011
I have upgraded our LMS 3.x to the new LMS 4.x Version. have installed the new 4.x on an new server and importet the backup.
I have importet a Certificate and have enabled the Browser-Server Security Mode, Enabled I added some new Netshow Jobs which run every day.
I get the email from the jobs and the URL in the email but, URL
When i click on the link i only get:
Forbidden: You don't have permission to access /rme/NSViewJobResults.do on this server.
Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request.
i must change the link to Urls there anywhere an option to edit the text which is send with the jobs, to fix the url?
View 4 Replies
View Related
