Cisco AAA/Identity/Nac :: ACS 5.3 Additional LDAP Attribute Retrieval
Aug 28, 2012
I'm authenticating users against Active Directory and want to also check additionals attributes from LDAP. In ACS 5.3. it was possible to set this up via External Identity Sequence, but in ISE I don't see this possibility. I can set sequence only for authentication, but not for additional attribute retrieval.
When I set a condition in a policy that an LDAP attribute must match with some value, the attribute is not retrieved and autorization ends on default Deny Access.
View 17 Replies
ADVERTISEMENT
Dec 21, 2012
I have a working ASA 5505 that is used for remote access. It authenticates users via RADIUS (Microsoft AD using two IAS servers), it also authorises users via LDAP and it does some LDAP attribute mapping to get group membership for DAP. This is all working fine however recently I enabled IPv6 to do some testing. I have a /126 subnet on the Inside interface (maps to its equivalent /30 IPv4 subnet) and OSPFv3 running so the ASA has visibility of the internal IPv6 networks. DNS client is enabled in the ASA and all the authentication servers are entered as hostnames. The two RADIUS servers only have A records and the two LDAP servers (Windows DC's) have both A and AAAA records. My plan was to begin test IPv6 on the AnyConnect VPN clients (once I was happy the ASA was working fine with IPv6).
When I initially enabled IPv6 everything continued to work as before, however I had to reboot the ASA today and after it all came back up authorisation stopped working. I did a bit of troubleshooting and the ASA is complaining of not being able to resolve the addresses of the two LDAP servers. From the CLI I can ping the hostnames and the LDAP servers resolve to IPv6 addresses and the RADIUS servers resolve to IPv4 addresses. When I issue the command 'show aaa-server LDAP' (LDAP is the name of the group) I see the servers listed but the address displays 0.0.0.0:
Prior to the reboot both the LDAP servers were showing thier addresses (IPv4) correctly. I can workaround it by disabling IPv6 on the ASA, letting it lookup the (IPv4) addresses of the LDAP servers (so they appear in the 'Server Address:' field above) and then re-enabling IPv6. Strangely deleting and re-adding the servers just with their IPv4 addresses also fails but I haven't fully tested this. I don't know but I think I would have the same behaviour if the RADIUS servers also had AAAA records.
I assume when IPv6 is enabled on the ASA it will perform AAAA lookups as well as A lookups but the LDAP client cannot use IPv6? Just guessing at the moment as I haven't managed to get a LAN capture. [code]
View 1 Replies
View Related
Sep 20, 2011
After trying for several hours to configure ldap attribute to cisco attribute mapping, I found that special characters are not supported by ldap attribute-map at least on 8.4
Here is the problematic configuration:
ldap attribute-map ldap_memberof_map
map-name memberOf Group-Policy
map-value memberOf
[Code].....
View 1 Replies
View Related
May 30, 2011
I want to configure RBAC for ANM 4,2 using tacacs+ and ACS 5.1 [code]
When the admin user logs in, this policy element is triggerd, but the Role is not sent back.How to configure the Custom Attribute?
View 1 Replies
View Related
Jun 28, 2011
We have just set up a Secure ACS 5.2 VM to provide authentication for Anyconnect VPN clients. The clients connect to an ASA 5520, which queries the ACS, which in turn queries Active Directory directly. All seemed to work OK, but I noticed it was using PAP. Following some docs, MS-CHAPv2 was enabled via the "Password-management" command. This broke the configuration and the error on the ACS was:
11309 Incorrect RADIUS MS-CHAP v2 attribute Some references suggest that the ASA and ACS should talk MSCHAPv2 without additional config, so I guess it must be the ASA config for the tunnel-group. There are additional secondary authentication and authorisation pages on ASDM, that I suspect might be necessary to use mschap.
View 1 Replies
View Related
Feb 21, 2005
I'm using Cisco ACS 3.3 for RADIUS. How to do I make Vendor-Specific attribute available? (Attribute number 26, format: OctetString) The online help makes reference to it, but does not tell you how to make it available.
View 9 Replies
View Related
May 13, 2013
ACS 5.3 always sends the class=cacs:xyz attribute in an authentication response. How can I suppress that behaviour? The Cisco Email Security Appliance doesn't support multiple class attributes (defect 49096) and even treats guest users as administrators.
View 2 Replies
View Related
Jul 18, 2011
how to add tacacs custom attribute to ACS 4.2 for Nexus 1000V:shell:roles="network-admin admin-vdc"In the interface configuration I've added new service, service - shell, protocol - tacacs+.In the group settings I've enabled this attribute configuration. And it is not works. Default privilege level is assigned to any user with access allowed.
View 8 Replies
View Related
Mar 19, 2012
how I can determine what attribute is coming up as 'invalid' ?Tried full debug and looked at all the logs - nothing.
View 1 Replies
View Related
May 18, 2011
I have a new Cisco Secure ACS 5.2 on a VM. We want to use it to for administrative access to our Cisco equipment with TACACS+. I am trying to map user permissions to different groups of devices based on active directory group membership, however it is not working.
I am using an LDAP (configured for secure authentication) external identity store. On the directory organization tab, I have confirmed the accuracy of the subject and group search base and the test configuration button shows that it's finding > 100 users and >100 groups.
On the directory groups page I have entered the groups according to the required format. cn=groupname1,ou=groups,dc=abc,dc=com
I have a rule based result selection under group mapping. I have two rules in the format below.
Conditon
LDAP:Externalgroups groupname1
Result
Identitygroup1
I have the default group set to a identity group named other. My problem is, no matter what user attempts to authenticate, the Default rule is applied, and the user is put into the other identity group.This occurs when I log on as a groupname1 user, groupname2 user, or as user that is not a member of either of those groups. LDAP authentication works and the user is able to logon to the device.
View 3 Replies
View Related
Feb 28, 2012
I am doing 802.1X for a user on Cisco 3650 and wanted the Radius Server to return an attribute to set the Duplex setting of the port. with the correct Radius Return Attribute.
View 4 Replies
View Related
Jun 22, 2011
provide me Step by Step procedure for integrating LDAP with ACS 5.2 .
View 1 Replies
View Related
May 16, 2011
I am having a problem getting an ASA running 8.3 to authenticate an SSL VPN directly against an LDAP on Windows Server 2003. I have changed the read access on the Active Directory to allow Annonymous to read it. I think I am missing something on the ASA config. I have the Server Group specified with the address of the correct server but nothing else really configured.
View 1 Replies
View Related
Oct 23, 2012
know about Domino LDAP ? I would like to integrate this LDAP with Cisco ISE.I try to bind this LDAP but it does not show me anything in "Naming Context". So I cannot choose group to map into ISE.I test this on WLC. It is success to do but cannot make the same thing with Cisco ISE.Is this LDAP supports with Cisco ISE 1.1.1 ?
View 3 Replies
View Related
Jul 31, 2012
I have 2 SSIDs on WLCs.I would like to have 1 SSID point to the acs radius using LDAP store and the 2nd SSID point to the acs radius using the host identity store for mac filtering.both scenarios are working, but not together.if I adjust the rule order I can get one SSID, but then the other fails. [code] It seems to me that there should be a simple process to make this happens. I thought if the rule is not matched it would move on to the next rule etc.I might be able to live with first checking ldap and if that fails move on to the local host db, but that seems ineficient. url...
View 3 Replies
View Related
May 8, 2011
I have an CS-ACS appliance with 5.2.0.0.26.3 version. There is not any direct solution for connect ldap client to server. I have 3 servers that have only ldap and for authentication I can not use radius or Tacacs+. I need a solution for this problem. How can LDAP Client connect to ACS when it has only ldap protocol?
View 1 Replies
View Related
Sep 13, 2011
is it possible to validate the ACS Application Accounts against an external repository like LDAP? I have found that LDAP can be used only as Identity store to authenticate users on AAA clients and Network devices.
View 0 Replies
View Related
Mar 2, 2011
I have a problem with LDAP authentication. i have an Cisco Asa5510 and windows 2008 R2 server. i create LDAP authentication.
aaa-server LDAPGROUP protocol ldapaaa-server LDAPGROUP (inside) host 10.0.1.30 server-port 389 ldap-base-dn dc=reseaux,dc=local ldap-naming-attribute sAMAccountName ldap-login-password ***** ldap-login-dn CN=user,OU=Utilisateurs,DC=reseau,DC=local server-type microsoft
but when i test, i have an error (user account work directly in server)
test aaa-server authentication LDAPGROUP host 10.0.1.30 username user password *****
INFO: Attempting Authentication test to IP address <10.0.1.30> (timeout: 12 seconds)ERROR: Authentication Rejected: Unspecified
View 11 Replies
View Related
Feb 9, 2012
i have a wireless deplyoment with WLC 5508, ACS 5.2 and several AD connected by LDAP. It is required that users are authenticated by certificates additional the user should only get access to the wireless environment when the user is found in a certain security group in the Microsoft AD forrest. The certificate based authentication is working without any problems, except the lookup into the AD isn't working. Here are the Details of the "Evaluting Identity Policy"
Evaluating Identity Policy
15004 Matched rule
22037 Authentication Passed
22023 Proceed to attribute retrieval
24031 Sending request to primary LDAP server
24016 Looking up user in LDAP Server - Alex Dersch
24008 User not found in LDAP Server
22015 Identity sequence continues to the next IDStore
24209 Looking up Host in Internal Hosts IDStore - Alex Dersch
24217 The host is not found in the internal hosts identity store.
22016 Identity sequence completed iterating the IDStores
but the user can access the WLAN just without verifying the user in the AD.
i tried the to enable Binary Comparisation but then the Authentication is not working any more. I get the same Identity Policy result as above.
i configured the Binary Comparisation as below:
I though with the binary comparisation i'll be able to verify the existance and the status of an user in the Active Directory.
View 1 Replies
View Related
Jan 24, 2012
Does Cisco Secure ACS 5.3 support LDAP authentication with Apple Mac OS X server? One of our clients require an access control system. The major portion of the network consists of Apple Mac OS X 10.7 (Lion) Server and clients. They were using MAC-address based authentication along with LDAP through Cisco Wireless LAN Controller. But now the number of users has exceeded the maximum number of MAC addresses supported by WLC (2048). Hence we suggested ACS appliance to overcome the limit. My doubt is whether ACS 5.3 appliance can communicate with the Mac server and perform LDAP authentication.
View 2 Replies
View Related
Jan 14, 2010
I've set up a ACS 5.1 Server an want to use it with our LDAP System. Therefor, I'm trying to login to a Cisco 1841 by using my LDAP Account, but it dosent work. The ACS seems not to know that it should use LDAP, because I get,"22056 Subject not found in applicable identity stores"LDAP is configured as Identitiy Store, the bind test works successfully and I created a sequence, where LDAP is at first position. What goes wron?? (TATACS for loal ACS Users works)
View 3 Replies
View Related
Mar 15, 2012
I am setting up an LDAP identity store over ldaps in ACS 5.1. I specify that the connection uses secure authentication and provide the Root CA certificate. When I hit "Test Bind to Server", I get this error message in a popup window: "Connection test bind Failed :server certificate not found"Is this saying that ACS can't find the CA certificate uploaded, or does it mean the actual certificate presented by my LDAPS server during the bind test?
View 2 Replies
View Related
Mar 13, 2011
I am configuring an ASA 5520 for VPN access. Authorization & Authentication use an LDAP server. I have the tunneling configured successfully, and I can access internal resources. What I want to do now is to restrict access to a specific AD Group membership. In the absence of that group membership, a user should not be allowed access to the VPN.
My test VPN client software is Cisco Systems VPN Client Version 5.0.05.0290. The group authentication is configured into a Connection Entry that identifies the Tunnel Group. I think I worded that correctly.
The Software Version on the ASA is 8.3(1).
My current challenge is getting the VPN to stop letting every access request through regardless of group membership.
[URL]
The configuration (AAA LDAP, group policy, and tunnel group) is below.
aaa-server LDAP protocol ldapaaa-server LDAP (inside) host x.x.y.12 server-port 636 ldap-base-dn dc=domain,dc=com ldap-scope subtree ldap-naming-attribute sAMAccountName ldap-login-password ******** ldap-login-dn
[Code].....
View 2 Replies
View Related
Mar 22, 2011
i'm trying to configure acs 5.2 to LDAP external idenity store, when LDAP failes ACS 5.2 should use internal indenity store. I configured A sequence to use LDAP 1st then Internal and i shut off the link to the LDAP but ACS will not use internal, AAA Diagnostics keeps telling me that Cannot establish connection with LDAP server and will not use the internal store.
View 7 Replies
View Related
Sep 27, 2012
I am working on project with Secure ACS 5.2. I am trying to determine the proper External Database to use. LDAP or direct to AD?
Additionally, the Domain that I am connecting to has Multiple sub domains. All of the users are currently in the Sub domains, but will be moving to root domain later. How should I configure the connection, do I need to connec to each sub domain or can I just connect to the root?
View 2 Replies
View Related
May 9, 2012
I have a problem where occasionally a user will attempt to login and the LDAP search will find the user but then fail when it does the group search. The error I get is below
22037 Authentication Passed
22023 Proceed to attribute retrieval
24032 Sending request to secondary LDAP server
24016 Looking up user in LDAP Server - testuser
24004 User search finished successfully
24027 Groups search ended with an error
24034 Secondary server failover. Switching to primary server
24031 Sending request to primary LDAP server
24016 Looking up user in LDAP Server - testuser
24004 User search finished successfully
24027 Groups search ended with an error
22059 The advanced option that is configured for process failure is used.
22062 The 'Drop' advanced option is configured in case of a failed authentication request.
Some users never get this error, others will get it once in a while and I have one user that gets it every time they try and login.
View 3 Replies
View Related
Aug 19, 2012
Cisco 5508 wireless controllerCisco ACS 5.1LDAP connection I have setup the wireless controller to do RADUIS authentication with the ACS 5.1 using LDAP. The setup is currently working, Brief info below on setup.
I setup the PC client to use WPA2-Enterprise AES and authentication method CISCO PEAP. When I connect to the SSID this will prompt for a username and password. I will enter in my AD details and the ACS with the LDAP connection will authenicate and on the network I go.
Now I want to add machine authentication with CERTIFICATES, each laptop and pc in our network has CA certificates installed.
way that I can add these certificates into the ACS 5.1 so I pretty much want to import them into the ACS. Once they are imported inside I want the ACS to check that the certificates are on the PC and then prompt for the AD username and password, and only once it meets these two conditions it allows the workstation onto the network.So it will be a two form authentication one with certificates and the other ldap.
View 18 Replies
View Related
Aug 2, 2011
I'd like to configure wireless access from winXP to authenticate with our corporate Novell LDAP through ACS
Setup:
WinXP SP3 --> WLC 4402 --> ACS 5.2 --> Novell LDAP
1. Our Novell LDAP server uses secure LDAP (port 636) to authentication user.On ACS 5.2, when we configure this option we need to select Root CA. Should the Root CA in ACS must be the same as the LDAP server's? (the LDAP's certificate issuer)
2. What kind of authentication that this setup supports? Does it support PEAP/MSCHAPv2 as in Windows Zero Configuration or it only supports PEAP-GTC, EAP-FAST, EAP-TLS (which means I have to use Intel Proset/Wireless software to configure).
View 2 Replies
View Related
Dec 17, 2011
While configuring LDAP , I got struck in “Step 3 - Directory Organization”. How to make this work? My aim is to make users authenticated from their windows domain usernames and passwords while they log in to AAA clients.
View 1 Replies
View Related
Sep 1, 2011
I have 2 ASA 5520 (v. 8.21) in a active/standby fail over configuration.
VPN users are autenticated against the MS-AD through LDAP. For the most part this works well. Occasionally I'm having problems with new users in the AD. If I run a test I keep getting "User was not found". This can happen days after the account was created still. In some cases it never seems to work. The accounts I create exists on the same OU level as all the other accounts that are working.
View 2 Replies
View Related
May 25, 2011
How can I find what my network key is
View 1 Replies
View Related
Feb 28, 2013
I've configure Ldap authentication on ASA 5545 to allow only a certain user group. I mapped the the memberOf group but this seems not to be working as it allows all AD users. [code]
View 1 Replies
View Related
Sep 1, 2011
I have a ACS 4.2 under windows, I setuped it to authenticate routers by RADIUS and TACACS+ protocols. now I have some devices whitch know only LDAP protocol. How can setup ACS as a ldap server to authenticate those devices?>
View 1 Replies
View Related
