Cisco AAA/Identity/Nac :: ACS 5.3 - Application Failed To Start

Apr 28, 2012

Although, ACS states its installed, after going through the startup. However when I do show application nothing comes up. When I do a application start acs, %Application failed to start.

View 7 Replies


ADVERTISEMENT

Cisco AAA/Identity/Nac :: 3395 - Getting Error - Failed To Start DB

Oct 14, 2012

While installing ISE 3395 i am getting error failed to start DB!
 
Database is not available withintimeout of 240 seconds.this could be reason of incorrect network configuration or lack of resources on the appliance or VM, run the folloing CLI to re-prime database 'application reset-config ise'

View 3 Replies View Related

Windows 8 Pro - The Dependency Service Or Group Failed To Start

Feb 23, 2013

I've been working on my laptop recently, once finished i turned my computer off like most people do. After turning it back on hours later, i noticed that my laptop was connected to the internet router but had limited access which ment i could'nt get onto the internet ! So when I went onto Network and sharing center and nothing came up apart from ''the dependency service or group failed to start'' ...I don't want to use system restore or reset tools of windows

Current OS: Windows 8 PRO
Model: ASUS K43SV

View 1 Replies View Related

Dependency Service Or Group Failed To Start - Error 5

Jul 20, 2011

DHCP Client and Network Location Awareness aren't working. When I tried to start DHCP Client, I got Windows could not start the DHCP Client service on the Local Computer.Error 5: Access is denied. I checked the dependencies and all of them were on. For Network Location Awareness, I got the error Windows could not start the Network Location Awareness on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service cendor, and refer to service-specific error code -1073741288. One of its dependencies is fine, but I don't know how to check the other two, Ancillary Function Driver for Winsock and NetIO Legacy TDI Support Driver. Also, how do I check the event log?Everything on the list that was said to check is running expect these two the lisie was having problems with. I have not had anything with memory recently and have not been able to successfully go through a system restore. I have tried many of the suggestions and just am not sure what to do anymore. The computer works perfectly fine, minus it cannot get on the internet.

View 1 Replies View Related

Cisco Wireless :: 3355 Mobility Service Engine Failed To Start

Nov 14, 2012

After I initial MSE with the wizard. MSE take so long to start the service (more than 1 hour) with "Starting MSE Platform, waiting to check the status"Then I decide to reboot the appliance, after that MSE shows the message "Traceback (most recent call last) File "/usr/sbin/yum-updatesd", line 40, in ?import gaminImportError: No module named gaming.

View 7 Replies View Related

Cisco :: Catalyst 3750 - Failed To Start Acquisition / Device Unreachable

Jan 26, 2012

We are using Catalyst 3750 switch stacks with software 12.2(44)SE. We have two stacks, only one with IP routing enabled.When we try to run an Acquisition Action on this, from Admin> Collection Settings> User Tracking, the system replies with an error "Failed to start acquisition: Device unreachable. Please enter a valid device"device Center reports "success" on all collector status.Acquisition starts successfully when we try with the other stack.With LMS 4.1 demo, users acquisition runs successfully.

View 18 Replies View Related

Computer Won't Detect Ethernet Cable - Dependency Service Or Group Failed To Start

Mar 7, 2012

My roommate and I are trying to set up the internet, but my computer won't detect the Ethernet Cable. Whenever I go to Network and Sharing Center and try connecting to the internet, the computer simply says "Windows did not detect any networking hardware", even though the light is clearly on and should be working. The cable is also new so it should be fine. I've also been looking around on the internet a bit, and in trying to fix the problem it looks like some of my Services are turned off, which seems to be causing the problem. However, whenever I try and turn them on, I get an error message saying "The dependency service or group failed to start".

View 5 Replies View Related

Cisco Application :: 474 / 594 - Remotely Start WAAS Appliance?

Mar 10, 2013

We have several 474 and 594 class WAAS appliances in the field. When power is lost to a given location, almost all of the other devices we have at these sites will start themsleves back up upon the restoration of power. Since the 474 and 594 WAAS appliances are basically PC based devices they do not seem to have the ability to start themselves back up when power is restored. What we would like is to have a solution wherein the WAAS device powers up on its own once power is restored much like the routers, switches, servers and PBX devices at the same location.

View 1 Replies View Related

Cisco :: LMS 3.2 Failed To Start Acquisition / Device Unreachable / Enter A Valid Device

Jan 3, 2013

We are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.

View 3 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.2 - No Start Records In Radius Accounting Reports

May 26, 2011

I do not see any start records in Radius Accounting reports but do see only Stop records ?
 
btw I am running ACS 5.2

View 2 Replies View Related

Cisco Application :: Nexus1000V-VSM-PDC / N1k Installation Failed

Apr 18, 2013

i try to install n1k VSM on Cisco UCS server(4Gb memory free).Due installation i got messgae-An error was received from the ESX host while powering on VM Nexus1000V-VSM-PDC.Failed to power on VM.Could not power on VM : Admission check failed for memory resource See the VMware ESX Resource Management Guide for information on resource management settings.

Group vm.1014695: Invalid memory allocation parameters for VM vmm0:Nexus1000V-VSM-PDC. (min: 524288, max: -1, minLimit: -1, shares: -3, units: pages)
Group vm.1014695: Cannot admit VM: Memory admission check failed. Requested reservation: 534234 pages

View 1 Replies View Related

Cisco Application :: Failed Installing Performance License On ACE 4710

Sep 5, 2012

I'm trying to install performance license on ACE 4710 appliance and it was failed. [code]

View 11 Replies View Related

Cisco Application :: ACE 4710 Failed Probe And Established Connections

Jan 23, 2013

I have four ACE 4710. Each pair of ACE is in one geographical location. Probes are configured so that it is checking regular regex (HTTP GET).When there is need rserver update we change text in our testpage.html (for ie. from "OK" to "SUSPEND" ) so that probe detect fail. In fact rservers are still operational, but should not accept new connections. This works fine. BUT I observed that established connection/sessions did not end up after probe fails. ACE probably wait for openned/established connections to end up and it is what I am askign for.What happens if probe fails but in fact rserver is operational? I thought that if probe fails it also end up/cut all established connections to rserver. But seems it is not true.

View 2 Replies View Related

Cisco Application :: Failed To Register WAE Because Primary Interface With WAVE-574

Nov 25, 2012

I'm receiving this error on a WAVE-574 appliance. The primary interface is configured and I can ping between the wave and the central manager.

View 1 Replies View Related

Cisco Application :: ACE 4710 License Installation Failed With No Space Left On Device

Jan 15, 2012

The installation of an ACE-4710 throughput upgrade license licence (ACE-AP-02-UP1) failed with an error message :CH01AC03/Admin#  license install disk0:ACE20111213081741975.lic.Installing license... failed: No space left on device. [code]

View 4 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.3 Secondary Registration Failed

Jun 5, 2013

I've just had to rebuild my ACS appliance with new hardrives but I am unable to register the devices to each I get a system error. I thought it may have had something to do with the rebuilt device not being joined tothe domain but it has now been joined albeit using a different ad account, but still cannot register to primary.

View 11 Replies View Related

Cisco AAA/Identity/Nac :: 802.1x Failed Authentication With WS-C3750G-24T

Mar 12, 2013

I have already set up a lab  comprising of  1x2950-24 switch, 2x3750-24T in stack mode and 2x MS Domain Controller with AD 2008 Servers and NPS enabled (Domain level 2008). I use NPS as a Radius Server. I am trying to test the 802.1x framework in two scenarios.
 
1.     I use as client a domain laptop with Windows XP SP3 with the embedded 802.1x MS supplicant. As authenticator use the 2950 switch and as authentication servers I use the two NPS integrated in MS DCs. Everything is working fine as I expected with basic configuration guidelines from Cisco & Microsoft.
 
2.      I use as client a domain laptop with Windows XP SP3 with the embedded 802.1x MS supplicant (the same as before). As authenticator I use the 3750 Stack switch and as authentication servers I use the two NPS integrated in MS DCs (the same as before). I have configured the supplicant for both machine or user authentication in both scenarios. However the client never pass the authentication in the second one. I disconnect and connect the same supplicant in the 2950 switch and the authentication is completed successfully. Getting back to the 3750 stack the authentication failed and the laptop gains network access in the configured Auth-Failed Vlan. I have tried several configuration changes without success. I cannot understand why does this happen. I have made some debugs and I am sending them a long with a partial basic configuration of 3750 stack switch.

View 7 Replies View Related

Cisco AAA/Identity/Nac :: ISE V1.1 NAD 6500 Failed To Decrypt Key

Sep 11, 2012

I´ve implemented 2 Cisco ISE v1.1 in HA to run MAB and 802.x Authentication / Authorization. Using Local ISE DB and Active Directory as an External Identity Source for wireless and wired users and devices. This was working fine 2 weeks ago after finishing installation.
 
My NAD devices are a Core SW 6500 for wired users (there are no access SW, just the Core for the whole network, its a small office) and a WLC 2405 for Wireless Users.[code].....

View 3 Replies View Related

Cisco AAA/Identity/Nac :: W2003 / ACS Tacacs Authentication Failed

Jun 27, 2012

we have a ACS server V4 installed on W2003 server ,when we make a telnet to an equipement on the wan the authentication pass on the first connexion ,but when we telent to a switch on the lan the first connxion fails and we need to retry to login .when i check the  field attempt log on the ACS i dont find the field attempt.i find this issue in ALL switch on the LAN ,from the switch i can ping the the ACS server .this problem appear frequently?

View 1 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.3.0.40 On-demand Full Backup Failed

Dec 27, 2012

I have ACS 5.3.0.40 Primary Secondary Authenticators , of which the Scheduled backup has stopped.When checked the : Monitoring Configuration > System Operations > Data Management > Removal and Backup > Incremental Backup , it had changed to OFF mode. without any reason.Later i did the acs stop/start  "view-jobmanager" and  initiated the On-demand Full Backup , but no luck, same error reported this time too.

View 2 Replies View Related

Cisco AAA/Identity/Nac :: Wireless ISE - 12508 EAP-TLS Handshake Failed

Mar 21, 2013

I'm in the middle of my very first wireless ISE deployment and I'm hitting issues with EAP-TLS based authentication.  In short, all EAP-TLS authentication is failing with the following error.  Below that is the relevant excerpt from the logs:
 
Authentication failed : 12508 EAP-TLS handshake failed
 
OpenSSLErrorMessage=SSL alert: code=0x233=563 ; source=local ; type=fatal ; message="X509 decrypt error -  certificate signature failure", OpenSSLErrorStack=   597863312:error:0D0C50A1:asn1 encoding routines:ASN1_item_verify:unknown

[Code].....

View 5 Replies View Related

Cisco AAA/Identity/Nac :: 002SWC003 - ISE Dynamic Authorization Failed

Dec 5, 2012

I am gettning warning messages in ISE saying

Cause:Dynamic Authorization Failed for Device: 0002SWC003 (switch)Details:Dynamic Authorization Failed 
 
It is not only on that switch but on all switches I have configured. I am using 3560 IPBase 12.2(55)SE6. I have configured them according to Trustsec 2.1. My end devices are none-802.1x. I can't figure out what is causing this error.
 
The thing is that I have not experienced any problem. In Live Authentications there are some 'Unknown' and 'Profiled' devices hitting the DenyAccess rule, but other then that everying is beeing Authorized fine.

View 8 Replies View Related

Cisco AAA/Identity/Nac :: ACS Version 5.2.0.26 / Failed MAB Authentication Logs

Jan 8, 2013

Having an issue where a user will plug a PC into a switch.  The switch does a MAB authenticaiton and the MAC is not located in the ACS server.  It logs the failed attempt, but when the PC is removed from the switch, the failed attempts keep getting logged until the port is bounced.  Any way to keep the attemps from happening after the PC is removed?  If not, any way to make it stop without bouncing the port?
 
running ACS version 5.2.0.26
 
switch port config: 
interface GigabitEthernet1/0/2
sw access vlan 2 sw mode access
authentication control-direction in
authenticaion host-mode multi-auth
authentication port-control auto
mab
spanning-tree portfast

View 2 Replies View Related

Cisco AAA/Identity/Nac :: Radius Authentication Failed On 6509

Jan 29, 2012

I have configured Radius authentication on Windows 2008 server (NPS)  The following configuration is working perfectly on Cisco Switch 3560. [code]But, the same configuration is not working on Cisco Catlyst Switch 6509 (C3560-IPBASEK9-M), Version 12.2(46)SE, RELEASE SOFTWARE (fc2)/

View 2 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.2 License File Installation Failed

Sep 19, 2011

have a  ACS 5.2 version installed on Vmware . I  purchased below  liscense
 
Product Name                  : L-CSACS-5-LRG-LIC=
Product Description         : L-CSACS-5-LRG-LIC= : ACS 5 Large Deployment License (Electronic Delivery)
 
When i am trying to upgrade the liscense i am getting an Error " Liscense file installation failed : The liscense file must contain single base liscense "

View 2 Replies View Related

Cisco AAA/Identity/Nac :: Cannot Upgrade ACS 5.2 Transfer Failed (code 1)

Nov 29, 2011

I am facing an issue with several ACS appliances (some other work well) when upgrading to version 5.2.0.26.8.
 
When I launch the command acs patch install, I receive the following error message (we use FTP):
 
Failed to copy file '5-2-0-26-8.tar.gpg' from repository PatchRepository
(Error -302)
% Error: patch install 5-2-0-26-8.tar.gpg from repository PatchRepository - transfer failed (code 1)
 
This happens on three appliances but I could successfully upgrade 4 other appliances.
 
What is the reason behind this error code ? What could I do solve it ? I have already tried to create another repository on another server, without success.

View 5 Replies View Related

AAA/Identity/Nac :: Command Authorization Failed In TACACS With ACS 4.2

Feb 2, 2012

We have a group in TACACS ACS4.2.  I configure it can do show command. When logged, it can do show command some parameters, like show ip interface, but it cannot do show running-config. it says "command authorization failed".

View 2 Replies View Related

AAA/Identity/Nac :: ACS 4.2 Authenticating 4710 ACE Appliance Failed

May 5, 2011

I've got a problem with Cisco ACS 4.2 authenticating Cisco 4710 ACE appliance.
 
ACS4.2 has been configured to use both internal and external database. It's been working fine for a couple or years.
 
Recently we bought a Cisco 4710 ACE appliance. When I use ACS4.2 internal username and password to login the Cisco 4710 ACE appliance, I have no problem. I can also see the passed authentication log on ACS4.2. However, if I use AD username and password, I couldn't login in. The message is "Login incorrect". I checked the failed attempts log on the ACS4.2, there was no log regarding the failed attempt. My AD username and password works fine on all other cisco routers and switches.
 
I've posted my AAA configuration of the 4710 ACE below. ACE is running on the latest version A4(1.1).
 
tacacs-server key 7 "xxxxxxxxxxxxx"aaa group server tacacs+ tac_admin  server xx.xx.xx.xx
 
aaa authentication login default group tac_admin local aaa authentication login console group tac_admin local aaa accounting default group tac_admin

View 2 Replies View Related

Cisco AAA/Identity/Nac :: ASA 5520 Failover Exec Authorization Failed

Mar 14, 2013

I have a pair of ASA 5520 firewalls running in active/standby mode on 8.3.2.34 code. My configuration performs authentication/authorization into ACS 5.1, however command authorization is failing when I try to execute a command on the standby from the active unit...
 
failover exec standby dir disk0:/
 
Fallback authorization. Username 'adminuser' not in LOCAL database Command authorization failed
 
I don't even see the authentication attempt going into ACS.

View 2 Replies View Related

Cisco VPN :: 7200 Getting IPSEC Decrypted Packet Failed SA Identity

Jan 23, 2013

I´ve try to configure a VPN IPSEC between a Cisco 7200 and Juniper ISG2000.The tunnel looks like good but when a ping is sending, I´ve packets lost and getting the next error:IPSEC(epa_des_crypt): decrypted packet failed SA identity check.My configuration en both sites is the follow: [code] What is the possible problem here. mea be in the Cisco 7200 configuration or in ISG Configuraton??

View 4 Replies View Related

Cisco AAA/Identity/Nac :: WLC To ACS 4400 V5 To AD - 12309 PEAP Handshake Failed

Feb 25, 2010

I have a Cisco WLC talking to a ACS 4400 version 5.1 which in turn talks to Active Directory.Ive been trying to get 802.1x for wireless clients going, I have a cert on the ACS from verisign on the box but when users try to sign in they get 12309 PEAP handshake failed in the ACS RADIUS log.The cert was exported and placed directly on the testing laptop and at one point it all worked.  I stepped away from it for 2 weeks to get a new internal CA built on a windows box, now coming back to it with the intent of issuing new certs to the ACS from the internal CA and thought I would check it to make sure all was good, but its not.Google doesn’t return happy results for “12309 PEAP handshake failed”, I opened a TAC case on it and they took my cert to their lab.  Haven’t heard back.

View 6 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.2 Failed Authenticate With Same Voice And Data Vlan

Apr 14, 2011

I have a question its posible to authenticate an cisco phone and PC with the same vlan(voice and data)when i do this configuratión , the phone and pc dont work. The phone display registering and never finished.interface FastEthernet0/5 switchport mode access switchport voice vlan 1 authentication event fail action authorize vlan 11 authentication event no-response action authorize vlan 11 authentication host-mode multi-domain authentication port-control auto authentication periodic authentication violation protect mab dot1x pae authenticator dot1x timeout tx-period 10 dot1x max-reauth-req 3 spanning-tree portfastend.

View 1 Replies View Related

Cisco AAA/Identity/Nac :: 3560 / TACACS (Command Authorization Failed)

Jan 3, 2012

While working in a 3560 all of a sudden I received the message "command authorization failed" while trying to issue certain commands.

It appears I lost my priv 15 authorization.  We have seen this before, we do not have access to the ACS to trouble shoot the issue.I tried logging in a 2nd and 3rd time using tacacs and received the same error whenever I issued a command such as dir flash: , copy tftp flash or show run. At the time I was trying to copy IOS to the switch, I had a co-worker log in and it was fine for him and he completed the copy.

Once completed I logged back in and all was fine again.   We suspect an issue with ACS? possibly a timeout of our TACACS authorization ?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved