Cisco :: AIR-LAP1131AG - Limited Access When Authenticated
Oct 8, 2011
At one of our locations we are experiencing some problems getting connected to our wireless networks.
It is possible to sit right next to an AP (AIR-LAP1131AG) and only have limited access to the network.
I have attached a snapshot from inSSID from the wireless networks in the area. All of them are broadcasted by our controller and I can´t figure out how it is possible to see SSIDs in other channels than the ones in the 2.4GHz band (11-14)?
View 1 Replies
ADVERTISEMENT
Oct 31, 2012
We've just replaced our Fortinet Firewalls with 5525's but are struggling to get a feature working that worked great on the Fortinet firewall.All our users use a proxy for internet access that's configured in IE but from time to time some users need to remove this proxy and go directly out to the internet, with the Fortinet devices we created a rule right at the bottom of the inside access out rule that had it authenticate users via TACACS which worked a treat and could be used from PC or laptop. We want to do a similar thing on the 5525 and I thought the Authenticated user would give me this access but I don't seem to be able to get it to work. I've got the AD side of it working fine the ASA can pull user and groups from AD but I'm struggling to get this working for a user.
View 3 Replies
View Related
Apr 26, 2011
On my wireless network, I am running guest access that I want to have as authenticated. If I enable WLAN, security, layer 3 web policy, when an iPAD / iPhone connects, they get directed to the Web Auth splash page, on where they must enter username & password. My users do not want to be directed to this page everytime they login - just select the SSID and connect - is there a way of authenticating guests via a WLC4400 without going through the splash page everytime?
View 6 Replies
View Related
Apr 1, 2012
I brought a LAP1131AG, only later found out that it can only be used with a controller.Is there any way I could change the firmware to make it a normall Access Point?
View 5 Replies
View Related
May 20, 2013
We have about 70 AIR-1131AG-A-K9 APs that were installed about 5 years ago. The controller we use is a 4404 WLC, with software 4.1.171.0. This provides us our wireless network. We use Cisco switches as access, distribution, and core switches.
We have two guest networks, one for visiting physicians and another for patients and their guests. Each of these guest networks use a 4402 WLC as an anchor controller, with software 4.1.171.0. They use the same APs as our business network.
According to my understanding of the guest networks is that a tunnel (I don't know if it is encrypted or or encapsulated) is created between the APs/Guest WLAN to the anchor controllers, so this guest traffic is isolated from our business traffic. Futhermore, these guest controllers connect directly to our firewall, which only allows them access to the Internet, and not our Internal LAN.
Our Problem
=========================
Well, we've been having problems with our wireless system, specifcally with patient guest access. It has gotten bad enough that they are looking to replace the Cisco APs on the south side of the hospital. We've been told that "you can get better guest access at McDonalds" : ( . I think part of our problem is that our controller code is so very old and we are have a our patient guest network open and "restrict" the number of clients attached to it by limiting our DHCP scope. The biggest complaint we get regarding the patient/guest wireless is people saying "I can't connect to the wireless", which we almost always identify as an issue caused by us running our of DHCP leases (we have about 200). These DHCP lease are used quickly, by an devices that comes into range that is set to automatically connect to any network that is in range. A lot of our staff is connected to our patient guest network and don't even realize it.
We are interested in Meraki APs because they are magaged using a cloud controller (we won't have the added expense of another controller) and they seem really easy to manage. Our biggest concern regarding Mearki is security. They make use of NAT, a Layer 3 firewall, and LAN isolation (a firewall rule that only allows clients Internet access) in each AP as a means of isolating the guest traffic from the business traffic. Does this seem like a secure way to accomplish this or are the Layer 2 tunnels that Cisco and from what I've been told recently Aruba and Juniper make use of a more secure approach?
We've been working with a Meraki vendor, who also happens to sell Aruba and Juniper wireless networks. It seems like don't suggest Meraki if we are concerned with security. They said they are good for situations where you have many geographically seperated sites. They suggested we use Juniper and Aruba, specifically because they use Layer 2 tunnels and that they used technologies like clear air (APs self adjust channels and power, which Meraki claims to do too). I thought that, hey does Cisco that too, why wouldn't we just go with Cisco if those are your selling points for Juniper and Aruba?
View 2 Replies
View Related
Mar 12, 2012
I have a modem connected to a router wirelessly and an access point few computers have access to the internet and some has limited access even those close to the access point.
View 2 Replies
View Related
Jul 10, 2012
I am trying to set up a Wireless network a WLC hosted on an SRE module in a 2911 router. I think i have most of my bases covered but there is still one problem.
My LAP1131AG AP's won't join the controller, on the AP im am seeing this:
Translating "CISCO-LWAPP-CONTROLLER.test.local"...domain server (192.168.250.10) [OK]
[Code].....
But to my knowledge an LWAP AP schould be able to join a CAPWAP WLC
View 2 Replies
View Related
Jul 31, 2011
WCS is reporting few AP's are not associated with it. While troubleshooting, AP conneceted switch interface shows UP/UP and show power inline output gives IEEE PD instead of AIR-LAP1131AG-E-K, after doing a shut/no shut on AP connected interface. Later after sometime AP comes up.
View 5 Replies
View Related
Dec 16, 2012
is it possible to shut down the LED on the AP LAP1131AG?
View 12 Replies
View Related
Jan 26, 2013
I have a WLC 4402 with many APs connected. Most of the APs are LAP1121 and LAP1131 and are working using 802.11b/g. I tried activating 802.11a but for some reason its not working. I see under the Monitor tab that the AP's "802.11a" interface is "down". I have enabled the radio under the "Wireless" tab. Under all the "WLAN" I have enabled all the radios but still not working. 802.11a" interface is still "down".
The AP Model is AIR-LAP1131AG-E-K9 meaning "ESTI" regulation. Under "Country" I "checked" IL.
View 2 Replies
View Related
Apr 2, 2012
I have 10 AIR-LAP1131AG-A-K9 connected to a 4402 controller. I have a couple of questions:
- When I go into CONFIGURE/ACCESS POINT, one of the AP's has the message "**Configuration is different on the Device**". How do I connect directly to the device to check the settings? I tried to telnet but that didn't work.
- Are these access points capable of acting as a DHCP server? If so, where can I check this setting? I have workstations that are unable to pull an IP address from my DHCP server running on a Windows server. I want to make sure the AP's and/or the controller are not the issue. The clients see the SSID and the signal is strong, but when they connect they get limited network connectivity message and the IP addr is 169.254.97.123 (which is wrong).
View 3 Replies
View Related
Feb 15, 2012
I've a 2106 WLC and the software is upgrade to 7.0.220.0. There are 3 APs with external power adapter work normally on it. Here is the problem: There is another AP with external power adapter has join the the WLC successfully. But it can not enable the radio 802.11b. Following is the error message on CLI
(Cisco Controller) config>802.11b enable AP001d.a1ef.b5f4 Cisco AP has not enough in-line power to enable radio
View 5 Replies
View Related
Oct 10, 2010
Since few days the WLC 2100 series controller and 3x LAP1131AG are getting disconnected and the controller gets offline via the local ip address. At that point I have to reboot. To get anywhere and after I connect wirelessly to the AP before I know it it disconnects. It worked for 3 years straight no fuss. And now nothing. I reconfigured the WLC 10times and no diffference.
[code]....
View 6 Replies
View Related
Feb 6, 2013
i have an AIR-LAP1131AG-A-K9 fresh from the box an was trying to register it to vWLC.I have them both on the same VLAN and these logs are showing on my WLC: [code]
The funny thing i have noticed is that both the WLC and the AP cannot PING each other.
View 14 Replies
View Related
Dec 9, 2012
The past two days have been frustrating with my wifi. When I first got on it, I checked the internet access because I couldn't get onto the internet. The connections had "limited access". I restarted my router and modem, and it did nothing. I unplugged everything and plugged it back it and the wifi would show, but I couldn't get on it. I restarted the router and modem, and it worked. I got on Cisco Connect and the signal wouldn't show. I got off the computer and later, I couldn't get on the internet again. Later on, I could get on the internet again. I got on Cisco Connect, and it still says that there is no connection. I haven't a clue what's going on. My modem is CenturyLink, and obviously, my router is Cisco.
View 19 Replies
View Related
Feb 6, 2012
Does any body know what is the maximum of simultaneous connections that the AIR-LAP1131AG-E-K9 access point supports?
View 2 Replies
View Related
Jan 23, 2010
I would like to return the cisco AIR-LAP1131AG-E-K9 to autonomous AP for it to function without WCS.
Sometimes it returns checksums error although the ios is valid.
View 6 Replies
View Related
Mar 10, 2012
we have WLC 4400, we have 40 APs with model no. AIR-LAP1131AG-N-K9 but we recenlty got an AP with model no. AIR-LAP1131AG-E-K9 which is unable to join WLC.
View 3 Replies
View Related
Nov 26, 2012
I am sharing a network with someone upstairs. They have a wired connection since they are close to the router - I'm using wireless.Routinely get 'No Network Access' or 'Limited Access' or 'No Internet' in the Wireless Network Connections box on my laptop and desktop.The person from who I am renting said it was a range issue. I purchased a range extender that plugs into the wall. This problem still persists, even for my laptop that I can take closer to the source.If I release the IP and renew it I can get a connection back but it usually craps out unexpectedly. This makes me think it's not a range issue, especially with the extender.When I look at an IP config report I notice "DHCP Enabled: No" and "Autoconfig. Enabled: Yes". I am not sure if I am sticking my nose in the right area with this last bit of information.
View 1 Replies
View Related
Apr 6, 2012
a new wireless adapter and modem installed, while everything can access the internet fine through this (including my laptop, which as far as I am aware does not support 802.11n) however her laptop can not access the internet. I can access wireless adapters but it say's that I am not connected and that connections are available.I thought that maybe it was a driver issue so I've updated to the latest (9.2.0.470) and still no luck. I got the driver from the Samsung page for the laptop, I tried it on my home network (which is not using 11n) and it still has the same problem. I've looked around but can't seem to fix it.
View 14 Replies
View Related
Nov 26, 2011
I attempt to log onto my parent's (golferguy) wireless network. It says under view your active networks: unidentified network (public network). Access type: No network access Connections: has the correct network name. When I click on hidden icons, it says that I have full reception but it says limited access.
View 11 Replies
View Related
May 12, 2011
I have limited access to internet
View 2 Replies
View Related
Nov 21, 2010
I'm using a wireless controller 5508 and 1141 Ap.Ultimately all the AP is working as LWAP.Everything is working fine.But offen end user getting "Limited Access " .At that time network is connected but i cant ping even my gateway.
View 7 Replies
View Related
Jan 23, 2012
I´m currently looking for a document that specify how many MAC addresses can be stored and authenticated via an ACS (1120)? I prefer to use the internal identity store over AD or LDAP for MAB authentication for 802.1X project. I would like to know what is the impact on the ACS? CPU/MEM? What is the impact on the user authentication? delay, timeout, etc.
View 7 Replies
View Related
Nov 8, 2011
I have a cisco ACS 4.0 build 27 on windows 2003 server . My site was working fine when i was having a AD on 2003 server . Recently i have migrated my AD servers is 2008 .
After the migration the ACS is not authenticating the users . Now i have made a server with 2003 and made the site working . I need a solution to make it work using 2008 server is there any compatiblity issue between ACS 4.0 and 2008 server .
View 1 Replies
View Related
Apr 4, 2013
I am using web authentication with my Wlc 5508 and I would like to check all users currently connected (ip, login used, MAC address, ...) with SNMP.
I am using an external web server and my client are authenticated with ldap.
I know I can receive these information with traps, but I would like to create a short program which will check all users when I click on a button.
View 2 Replies
View Related
Feb 28, 2013
I have a AIR-LAP1131AG-A-K9 this Ap is registered but, i cant enabling admin status on interface B/g, when select option throws a error. "Error in Enabling Admin Status"
View 4 Replies
View Related
Jan 13, 2011
I justgot a new computer and I connected it to my wireless network but I don't have any access to the Internet
View 1 Replies
View Related
Jan 25, 2012
i got my laptop back from it being repaired. Even though they haven't actually fixed the problem But anyway i cant connect to the internet, it comes up with 'limited access'
View 14 Replies
View Related
May 23, 2011
I have such limited access to some site that I usually browse. For sometimes, I was blocked from those sites. Those are the sites where I can get a lot of data/information I needed. Mostly, I am about to finish my work and have browsed those particular site for many times, then, the page give me an WinNT error of something like �You don�t have permission to blah blah� or �limited access� which is frustrating sometimes.What will I do so that I can access those sites? How will I set up the proxy setting? Do I need to download proxy software to switches the proxy server automatically?
View 3 Replies
View Related
Dec 23, 2012
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersAcer>ipconfig
Windows IP Configuration
Wireless LAN adapter Wireless Network Connection 3:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
[code]....
View 4 Replies
View Related
May 12, 2012
My laptop running Windows 7 has been fine until this holiday, connected to a hotel wifi that "trapped" the broswer and requested a login and password. That worked fine, but now I cannot access any other wifi networks.It sits for a while after entering the code and then has limited access, running the troubleshooter it says that I have no valid IP address?Tried IPCONFIG /RELEASE and it is saying "No operation can be performed on Local Connection 2 while it has its media disconnected"
View 8 Replies
View Related
Sep 14, 2011
Using Outlook to send & recieve mails from a webmail hoster, I regularly get booted off the internet and am left with the Limited Access message. Usually unplugging the router clears it but it is a nuisance to say the least.I have even tried reverting to a cable but the problem continues.The problem even happens to my wife's Samsung laptop, although the info below is from mine. [code]
View 8 Replies
View Related