Cisco :: ASA5520 / Two Firewall Are Unknown On LMS 4.0.1
Jul 5, 2011My customer had 2 asa5520 version:8.0(5)20 and LMS 4.0.1.Two Firewall are "unknow" on LMS, why ?Normally, LMS manages ASA with version 7 min.
View 1 Replies
ADVERTISEMENT
Cisco Firewall :: ASA5520 To ASA5520 Via L2L Tunnel
May 31, 2011Our firewall expert has gone off on long term illness leave and I am trying to pick up the pieces :-(
We have an ASA 5520 (local office) talking to another ASA (remote office) via a VPN Tunnel.
My 1st problem is that I cannot ping from my inside network (local) to the outside interface of my remote ASA.
My 2nd is that I have debug enabled on my rules but am not logging anything.
Cisco VPN :: Between ASA 5510 And Unknown Firewall?
Feb 14, 2013I set the asa Vpn to connect to the other firewall, the VPN is ok but when i see the logs of bytesTX and BytesRX the asa receive a lot of packages in BytesRX but dont send anything in BytesTX.
View 1 Replies View RelatedCisco Firewall :: Unknown Error On ASA 5505?
May 18, 2011This might actually go into Networking Basics because of the nature of the problem, but I tossed it in here because of the Cisco product involved. Long story short, I need to do some detective work to figure an apporpriate IP address for a NIC.I recently started working at a company with the ASA 5505 and I need to upgrade the software image on a bunch of them. There's already a computer set up with a TFTP server and Hyper-Terminal to do it. I'm trying to use the CLI update procedur[URL] but when I get to the beginning of the actual transfer from the TFTP, I get stuck at "Accessing" and then the connection times out with the message "Unknown Error".The only thing I can think of is that somehow the ASA is not making it all the way to the TFTP server, probably because the IP address settings on the NIC for the computer is set wrong. I say this because in the config file provided me, the ASA is given an address X.Y.Z.1, subnet mask /24 (where all the letters are constants) and the TFTP server has an addess in its software config of X.Y.Z.10 mask /24, but the NIC on the computer is set to A.B.C.105, which is an entirely different network.I need to figure out what I can make the NIC IP address so I stop getting the error. I tried a couple of different X.Y.Z.x addresses, but haven't gotten anything yet.
View 1 Replies View RelatedCisco Firewall :: ASA 5510 - Unknown 105008 And 105009 Logs On Non-failover Interface
Nov 26, 2012I have a pair of ASA5510s in a failover configuration where I see these 2 logs repeated every 15 seconds.
105008 1 Nov 27 2012 10:39:27 (Primary) Testing Interface management
105009 1 Nov 27 2012 10:39:28 (Primary) Testing on interface management Passed
I have read other threads where these are accompanied by "105005, Lost Failover communications with mate on interface". But I'm only getting these 2. The other thing that is confusing is that the "management" interface is not the failover interface. So why do I see 105008/9 logs about it?
Output of "sh fail":
5510a# sh fail
Failover On
Failover unit Primary
[Code].....
Cisco Firewall :: ASA5520 Bypass All Network Through Firewall
Dec 22, 2011With regarding to the firewall ASA5520, i'm using it in my network, all the confiuration are properly configured and working but with the use of proxy address in internet explorer(e.:206.53.155.129/3128) all the blocked contents as easily accessible simply it bypass all the network through firewall.so will u guide me to block the proxy servers.
View 1 Replies View RelatedCisco Firewall :: Keep ASA5520 Firewall In Sync
Aug 22, 2011I have two asa 5520 firewalls. one at my primary data center connected to our production Internet feed, and one at my fail over data center connected to a backup internet feed. I was wondering if there was an easy way to keep the firewall rules in sync between the two firewalls. We have failover with our isp that will move our public facing address block from our primary site to our dr site in the event of a disaster so the ip addresses will not change if we were to have to fail over to the DR site. currently i just have to do any changes that i make on the fail over server but would like a way to at least simi-automat this if not fully automat this so that i can eliminate the possibility of human error of a change happening at primary but never getting don at DR.
View 1 Replies View RelatedCisco Firewall :: Only One Internet IP Can Be Used In Asa5520?
Sep 25, 2011I have a asa5520 with five Internet IP.One for the internet interface and the others are static maped to dmz hosts. It runs rightly until yesterday.Now it will lose the connection to the gateway many times everyday and the dmz hosts can not connect to internet any time. configuration(simplified):
!
interface GigabitEthernet0/0
nameif internet
security-level 0
[Code]....
I called ISP to check,when ISP clear their router's ARP, the asa will lose the connection at the same time and then the ISP's router couldn't learn the ASA's MAC. After I 'clear arp' manually,The ISP's router can learn the ASA's MAC and the connection recovered,but the DMZ's cann't access internet still (of course,There is no problem between DMZ and ASA ,I ping the internet gateway from DMZ host and can not get any reply.).
Cisco Firewall :: Upgrade 8.2.2 On ASA5520?
Oct 3, 2011We have 2 x ASA5520 and I upgraded this to 8.2.2 last year, I see 8.2.5 and now 8.4 is out. If we are having no issues, is it best just to leave it as it is? I can see a couple of features I may find useful in 8.2.5, but 8.4 seems like a huge jump and a risky one too.
View 1 Replies View RelatedCisco :: Firewall ASA5520 Is Very Slow
May 8, 2011I have one firewall ASA5520, are very slow
View 3 Replies View RelatedCisco Firewall :: Cannot Ping ASA5520 From LAN
Mar 7, 2011I am trying to introduce an ASA5520 to my network based on the following diagram: ISP Internet ------> ASA5520 ------- > Cisco Router ------> LAN. The problem is I cannot ping the ASA from the LAN. I can ping it from inside the router. I already allow ICMP within ASA. If i remove the cisco router and replace it by a swich, I can ping the ASA with NO problem.
View 5 Replies View RelatedCisco Firewall :: ASA5520 With Different CPU Type?
May 16, 2011We want to use ASA5520 but both Firewall have different CPU. One has CPU Pentium 4 2400 MHz and another has Pentium 4 Celeron 2000 MHz. Can it be configured for replica / failover?
View 5 Replies View RelatedCisco Firewall :: LAN To LAN Between ASA5520 Version 8.3 And PIX?
Apr 19, 2011We have 2 firewalls on PIX facing the Internet and connected to interface e1 (behind it) an ASA version 8.3 Both the PIX (Firewall facing) and the ASA are on the same subnet.
By using Routing statements and statics I have been able to reroute specific traffic to the ASA5520 version 8.3 Now I need to inverse the 2 devices. The ASA5520 will be facing the Internet and the PIX will be behind it.Unfortunately the ASA5520 is refusing to route the traffic to the PIX. The access-lists are open accordingly and a NAT on the ASA has been created.
Cisco Firewall :: Client Uses ISP DNS Under ASA5520?
May 31, 2013i have my router connected to ISP then my router directly connected to my ASA5520....i use also ASA5520 as my DHCP Server and i was wondering with the DHCP Server function of ASA 5520 because if i use the ASA 5520 LAN ip ...all workstation will not be able to browse anything from the internet unless i use my ISP DNS IP which they gave me?
View 3 Replies View RelatedCisco Firewall :: Using CSC SSM 6.6.1125.0 With ASA5520 8.4(4)1?
Sep 4, 2012Get the following log message on secondary ASA console output when turning on the ASA failover function?
"Mate's service module (CSC SSM 6.6.1125.0) on slot 1 is different from mine (CSC SSM 6.6.1125.0)"
After that the secondary cannot join as a failover unit and shows in disabled status.We have the same model ASA & CSC module and each pair of them are in same firmware (CSC 6.6.1125.0 with ASA5520 8.4(4)1), when I shutdown both the csc modules, the ASA failover works fine.
Cisco Firewall :: ASA5520 To Act As Web Proxy
Dec 15, 2012I am using a squid proxy behind an ASA5520 firewall to collect the users to the internet. Squid is just necessary to log what is going on in order to find a quick solution when the internet slows down.
Considering that I have unlimited licenses and I would like to get rid of squid, I wonder if the ASA has some functionalities to track which websites are being used and how much traffic is generated. If there is not, I would like to know if Cisco offers a good product to replace Squid.
Cisco Firewall :: ASA5520 Upgrade 7.2 To 8.4
Jun 8, 2011Upgraded an ASA5520 from 7.x to 8.4 in one step? Release notes for 8.4 state that you can "...upgrade from any previous release directly to 8.4..." I've read the previous version release notes and see the various changes in NAT etc that 8.3 made.
View 3 Replies View RelatedCisco Firewall :: ASA5520 VPN Support Over DSL
Jan 5, 2012Any limits on the number of IPSec sessions an ASA5520 can support over a DSL connection?
Currently, as we increase the number of IPSec VPN tunnels, our LAN switches connected to the DSL/ASA start seeing CRC/input errors. Tried different LAN ports for both DSL/ASA connections - same reults (CRCs and errors). Swapped ASA for PC running 1 IPSEC w/HD video and no issues.
VPN connection bandwidth demand 50% of DSL capacity, so not exceeding DSL bandwidth. Errors get so bad that all VPN sessions drop - sometimes VPN sessions re-establish while other instances a DSL modem reboot is required.
cause of LAN switch connections seeing errors with 4+ VPN sessions established on ASA across a DSL Internet circuit?
Cisco Firewall :: Cut-Through Proxy Not Working With ASA5520
Jan 16, 2012I'm trying to configure an ASA 5520 with cut-through proxy feature. The user is required to be authenticated when trying to access an outside resource from the inside. This is a test lab before it is implemented in production. [code]
View 15 Replies View RelatedCisco Firewall :: How To Enable Not Used Interfaces On ASA5520
May 12, 2011I have a pair of brand new 5520s I am in the middle of commission. After carving out all the DMZs etc I needed I realized that I really neede another physical NIC, not just another VLAN off a configured nic. [code]I am running 8.3(2). How can I turn these "Not used" interfaces into useable ones?
View 2 Replies View RelatedCisco Firewall :: ASA5520 Cannot Ping Outside World
May 22, 2013I have Cisco ASA5520 with a 8.4 code in GNS3. I have a problem pinging to the internet. On the ASA console, I can ping to outside world, but on vpc I cannot ping the outside world. But I can ping the ASA Inside interface and other VLANs, no problem. [code]
View 3 Replies View RelatedCisco Firewall :: Access-list On ASA5520
Feb 23, 2011I have a question about access-lists on ASA: (5520 running 8.4)Often I want to permit all traffic from networks behind an interface (let's say DMZ in this example) to Internet, but NOT to internal networks. Then I first configure a Deny from DMZ to all internal network and then a Permit to ANY. If I forget the first Deny I will allow all traffic also to my internal networks. Is it possible to configure an access-list that permit all traffic from a network to all networks that are reachable via a given interface? In this example: Permit all traffic from DMZ to all networks that are reachable via the Outside-interface? This should permit traffic to Internet and deny traffic to internal networks in one statement.If I specify the outside-interface as the destination only traffic to the interface itself will be allowed.
View 1 Replies View RelatedCisco Firewall :: ASA5520 Not Allowing Traceroute
Oct 31, 2011I've got an annoying problem with my ASA 5520.I have traffic going from the inside interface (security level 100) to the outside interface (security level 0) with a global PAT applied to the outside interface address for all inside traffic - and I can't seem to traceroute through the firewall.The ruleset is simple - basically, allow any IP from inside to outside. The NAT is simple - PAT all traffic unless exempted to the IP address of the outside interface.If I do the trace from my internet edge router it works fine - so I know it's not soemthing my uplinks are filtering - but if I do it through the firewall, I get perfect responses until the hop where it hits the firewall interface - then nothing.Is there something I am missing that I need to do to allow traceroute to just work with all the rest of the traffic?
View 2 Replies View RelatedCisco Firewall :: How To Verify If CG-NMS Is Enabled On ASA5520
Apr 11, 2013how do I verify if CG-NMS is enabled on ASA5520. I just need to know if it's enable/install to be enabled and used?Cisco Adaptive Security Appliance Software Version 8.0(5)28..Device Manager Version 6.1(5)51
View 1 Replies View RelatedCisco Firewall :: Inspect Not Working In ASA5520?
Aug 15, 2012I have a cisco ASA5520 box running with IOS version8.2(5)13 where default policy map is applied globally. But I have not seen any traffic being inspected through included protocol defined under policy map.All configuration seems to be ok for me.
service-policy global_policy global
Global policy:
Service-policy: global_policy
Class-map: inspection_default
Inspect: ftp, packet 0, drop 0, reset-drop 0
[code]....
Cisco Firewall :: SSH Stopped Working On ASA5520?
Mar 27, 2012I can no longer SSH to a primary active firewall. It had all of a sudden stopped working. However I am able to SSH to the secondary standby firewall without any problems. I did try to regenerate the RSA key on the primary fw, but still unable to connect. The only way I can connect to it is by using telnet.
I ran the "show asp table socket" command and I'm seeing port 22 listening on the primary IP address (not the standby), foreign address is 0.0.0.0:*. I did a packet capture on port 22 on the inside inside, seeing my request hit the fw and then right away a reset back from the fw.
version 8.2.(5)
model ASA5520
I'm hitting a bug in the software version I'm running? Or what else can I check before rebooting the primary fw?
Cisco Firewall :: Zero Downtime IOS Upgrade On ASA5520
Jun 5, 2011We are planning to upgrade IOS on a 5520 pair, from 7.2.4 to 8.2.4, and cause minimum outage. And according to the documentation, we can do the zero downtime IOS upgrade by failing over to the standby ASA and back.
[URL]
So, can during this process, can we go from 7.2.5 to 8.0.5 (last maintenance release), or do we have to move to 8.0.2 first ?
Cisco Firewall :: ASA5520 And Public IP Zone
Apr 5, 2011I'm trying to setup a zone behind my firewall with complete publicly routeable IP addresses for 3 servers. The reason I'm doing this is I am in the network setup stage of an OCS implementation, and OCS connections don't behave well with NAT.
My device is a ASA5520. I have an internal zone, and a dmz zone. These are done via standard NAT configurations.
My question is this:
Is it possible to setup connectivity to the outside with internal servers that have Public IP's directly on their NIC's? Another little detail of interest is that this ip space is seperate than the one that's on current Outside interface facing our ISP. However we own both address space.
Cisco Firewall :: ASA5520 External Flash For 8.4
Apr 6, 2011I am in the process of setting up the ASA5520 with the latest 8.4 firmware latest Anyconnect 3.0.
Unfortunately, the internal memory is sufficient enough for the ASA ASDM only. It says not enough memory when I tried to tftp the Anyconnect pkg.There is a external flash slot at the back of the ASA, I've inserted a 256mb CF card but when I do a show disk1: it shows
Cisco Firewall :: How To Get Part Code On ASA5520
Jul 22, 2012What is the difference /how to show part number,part code and serial number on cisco ASA 5520 series.succeed to get serial number by command show activation-key detail..how to get part code /part number?
View 2 Replies View RelatedCisco Firewall :: Multiple DMZs On ASA5520
May 14, 2013Can we have multiple dmz's on asa 5520 or any other cisco firewall, if so how can we configure them and what would be the security-level for those and how to decide, i mean which one has highest and lowest. another question is what is the purpose of security levels, i mean security-level 100 for lan and 0 for wan and others between 100 to 0. whats the importance of numbers from 0 to 100, what do these numbers tell the firewall. I want to try ids in gns3 but i don't have the ios image, from where can i get it.
View 4 Replies View RelatedCisco Firewall :: ASA5520 Which Is Optimal IOS To For Upgrade
Jun 10, 2013i need upgrade two ASA5520 in failover. It´s has IOS 8.0(3) and ASDM 6.0(3).How is the correct procedure to upgrade two Firewalls?
Which is the optimal IOS to for upgrade and i not need make changes in config of ASA?
Cisco Firewall :: ASA5520 Failover Not Happening
Sep 14, 2011We have ASA 5520 configured for failover and it was working fine. When we wanted to reload the firewall and inactive( Primary) to become Active , we saw that it is in Failed state. The DMZ2 interface in the capture below is the logical sub-interface , but is in Failed State. The other sub-interface on the physical interface Gig0/2 are all fine for the Failed Firewall.
[Code] .............