Cisco Application :: ACE10-6500-K9 Supporting C6500 IOS

Dec 7, 2011

It seem that ACE10 not support 12.2(33)SXJ1 IOS running on C6500. The box cannot detect the ACE module when power up. Currently the ACE10 running on system A2(30).
 
My challenge i have the ASA SM that compulsary to run on 12.2 (33) SXJ1 version. How to let these 2 module can running on the same C6500 box?

View 1 Replies


ADVERTISEMENT

Cisco Application :: IOS Upgrade For ACE10-6500-K9

Oct 14, 2011

I have ACE10-6500-K9 installed in 6513 core switch with below mentioned sh version.
 
Software
loader:    Version 12.2[121]
system:    Version A2(2.0) [build 3.0(0)A2(2.0)]
system image file: [LCP] disk0:c6ace-t1k9-mz.A2_2_0.bin

[Code].....
 
I want to know that can i upgrade ACE10-6500-K9 to c6ace-t1k9-mz.A5_1_0 i.e version5 ? I tried to search cisco website but could not get proper upgrade or user guide.

View 2 Replies View Related

Cisco Application :: ACE10-6500-K9 / How Static Entry Under Sticky Performs

Jul 26, 2011

how a static entry under a "sticky" performs Configuring Static IP Address Sticky Table Entries Cisco Documentation Says When you configure a static entry, the ACE enters it into the sticky table immediately. Configuring the ACE Action on Server Failure failaction purge # The purge keyword specifies that the ACE remove the  connections to a real server  if that real server in the server farm  fails after you enter the  command. The ACE sends a reset (RST) to both  the client and the server  that failed. Cisco Documentation Says If you do not configure this command, the ACE takes no action when a server fails
 
sample config
sticky ip-netmask 255.255.255.240 address source STICKY1
timeout 180   replicate sticky   serverfarm SERVERFARM1   8 static client source 192.168.12.15 rserver SERVER1
  
Question1 - What happens if SERVER1 fails?
 
a) Does the ACE let the connections to SERVER1 timeout(default behaviour) and then load-balance new connections coming in deom 192.168.12.15 to another server in SERVERFARM1

ORb)  Does the ACE reset the connections to SERVER1  immediately and starts  load-balancing new conenction coming in from  192.168.12.15 to other  servers in SERVERFARM1 ?

ORc) Does the ACE just drop the current and new connections from 192.168.12.15 till SERVER1 comes back up ?

OR d) Is it dealt differently?
 
Question2 - Now what happens if the failed server(SERVER1) comes back up after some time?
 
e) Does the ACE reset any current connections from 192.168.1.15 and starts sending them to SERVER1 ?

ORf)  Does the ACE leave the current connections from 192.168.1.15 to other  servers in SERVERFARM1 as they are and send any new connections
from 192.168.1.15 to SERVER1?

ORg) Is it dealt differently?
 
My guess is Question1 -> a) and Question2 -> e)
 
ACE model =  ACE10-6500-K9
Version =  A2(3.3) 

View 4 Replies View Related

Cisco Application :: ACE10 Dynamic Port Range

Feb 3, 2013

the dynamic port range server load balancing supported for MS Exchange 2010

View 1 Replies View Related

Cisco Application :: ACE10 Version A2(3.6a) - Activate XML API Management?

Sep 18, 2012

We are using several contexts for each customer in our ACE module.One of the customer contexts needs to activate XML API to control their services.I've tried to activate it, but cannot get any http response, what can be missing?ACE10 version A2(3.6a)
  
class-map type management match-any HTTP-ALLOW_CLASS
  2 match protocol http source-address 10.110.0.0 255.255.254.0
  3 match protocol http source-address 10.60.208.80 255.255.255.248
class-map type management match-any HTTPS-ALLOW_CLASS
  2 match protocol https source-address 10.110.0.0 255.255.254.0
  3 match protocol https source-address 10.60.208.80 255.255.255.248

[code]....

View 3 Replies View Related

Cisco Application Networking :: Catalyst 6509 - ASN Traffic Ace10 Module

Aug 26, 2012

I trying configure ASN traffic load balance, but doesn't works.I have one Cisco Catalyst 6509 and onde Cisco Ace10 module, in my context "PanWEB" i have the interfaces above: [code] If i try to establish a telnet session(telnet 10.96.202.10 80) i see the SYN packet passing through the ACE and going to the real server, but, the server do not response the SYN packet. I done a capture in the server using wireshark and could see that the IP address of the destination is the VIP and not the rserver ip address , this is a problem? Why can not I have the SYN + ACK from the server?

View 5 Replies View Related

Cisco Application :: C6500 CSM Real Server Cannot Ping Its VIP

Oct 25, 2011

I've been running into an issue with Cisco CSM for a number of years, but always found a way around it.  Im attempting to get to the bottom of this to find out once and for all, if this is infact a limitation of the device, or a config issue/work around is possible.
 
Here is my situation.  My CSM's are configured in bridging mode.  Traffic works great, traffic bridges across vlans correctly.  Everything works and have many instances of smilar configurations running in production.  Every once and a while, a client requests that a "real" server (ie LWCMW-021)
cannot ping its VIP address (10.95.88.68).  I am assuming this is related to the NAT Server, but not 100% sure.  Clients have requested this functionality for some type of application based purpose, but Im unaware if CSM in bridging mode can provide this or not. 
 
real LWCMW-021
address 10.95.88.59
inservice
!
real LWCMW-022
[Code]....

View 5 Replies View Related

Cisco Application :: 6500 - ACE Compatibility With F5 GTM?

May 9, 2012

We have cisco ace 30 modules installed in cisco 6500 switches. For application availability purpose from the internet, we need to have some global site selector/3rd party devices with similar feature set that of cisco gss.
 
whether cisco ace is compatible to ge tintegrated with other 3rd party devices like F5 GTM?

View 1 Replies View Related

Cisco Application :: 6500 Cannot Communicate To Device

Jul 9, 2012

I have installed ANM 5.2 virtual appliance.I have an issue importing a Catalyst 6500 device.When I try to import it, I get the following error: Device discovery failed: Cannot communicate to the device.Authentication failure while attempting to connect. Verify the device type and credentials. I double verified and the credentials are correct.I user SSH version 2.I use the following special carachters in the password: "!" and space.I don't use enable password to connect to the 6500 device. The 6500 device has a privilege 15 username.In ANM, the enable password is a requirement so I just fill in the regular password.I think the issue is appearing due to one of the following:
 
1.) The ANM does not support the special carachters I use in the 6500 password.

2.) Then ANM requires enable password, while I don't use enable password in the 6500 switch.
 
The 6500 runs SXI6 software version.I can't configure an enable password or configure a test username without special carachters beacause it's against the organization's policy.

View 1 Replies View Related

Cisco Application :: 6500 / How To Display CSM Uptime

Sep 12, 2012

I have done this in the past but I cannot find it anywhere......how do you display the uptime of a CSM module in a 6500? The chassis has an uptime of over 2 years, but I believe the CSM module was power cycled at some point within that 2 years and I need to find out if we may be running in to the bug that occurs after 828days of uptime. We are running 4.2(6) on the CSM and 12.2(18)SXF1 IOS on the SUP.

View 3 Replies View Related

Cisco Application :: To Create A Static Bidirectional Nat On 6500

Jul 20, 2011

First of all, I want you to know that I do understand that it's not a good design at all, but I still need to implement it.My ACE20 in 6500 works in routed mode with VLAN 101 (10.0.101.0/24) as the client-side VLAN. I therefore have Vlan101 SVI (10.0.101.1/24) on 6500.I also have VLAN 200 (10.0.200.0/24) on 6500 with SVI Vlan200 (10.0.200.1/24) and I want to create a static bidirectional NAT so that clients, connecting to IP address in VLAN 200 (10.0.200.64) would be NATed to VIP (10.0.101.10).Let's say we have clients (10.0.500.0/24) connecting through gig1/0/1.Here is my current setup on 6500.

View 14 Replies View Related

Cisco Application :: Asymmetric Routing Seen In WAE When Using 6500 Switch?

May 23, 2011

When we do self diagnostic test for WAE connected to the 6500 switch i get warning as below. Due to this alert there is no major acceleration benfits by the WAAS
 
Test WARN  [tfo] WARN  ASYMMETRIC  Asymmetric routing is seen in the device Action:  Check router's network configuration and WCCP redirection on the router.usevwa1#
 
6509 switches has only L2 capability and does not do WCCP redirection. The WCCP re-direction is done by 2821 routers.Is there any command which needs to be given in 6500 switch to solve the issue

View 1 Replies View Related

Cisco Application :: ACE SM Indexing In A Catalyst 6500 VSS Environment

Mar 7, 2013

I was asked to mount ACESMs on each of the CAT6K switches of a VSS cluster (one ACESM on each individual switch).On a non-VSS environment, the "svclc module <slot> vlan-group <group>" command is used to bind the VLAN group to the module on a certain slot. But now I am facing a VSS scenario, I will need to combine switch and slot in order to reference each of the individual modules...
 
How do I "index" each of the ACESMs in a VSS cluster? ¿Is there an extension of the aforementioned command to be able to combine switch and slot information?

View 1 Replies View Related

Cisco Application :: Configure New ACE 30 Module On Top Of 6500 Core Switch

Jan 12, 2013

i have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?

View 1 Replies View Related

Cisco Application :: Password Recovery For ACE Service Module 6500

Dec 27, 2011

I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?

View 2 Replies View Related

Cisco Application :: ACE And FWSM Design And Configuration Guideline With 6500

Apr 8, 2013

I have Cisco 6500 with FWSM and ACE module which are in one central DC. Also we have four different Datacenter (Hub & spoke) and in our FWSM we have configured four contexts in central DC FWSM for each DC. Each DC servers are different VLAN and IP subnet. Now we have to configure ACE module for load balancing among those different subnet servers. What will be the design and configuration for this solution? Like routed or one-arm mode design.
 
Scenario Example:
1.  App Server01
IP:192.168.11.5/24
GW: 192.168.11.1 in FWSM
FWSM Context: DC1
Physical Location:DC1
VLAN:11

[code].....
 
Now customer requirement is we have to load balance using ACE between these App Servers which are in different context s in FWSM and one Server is not FWSM. how to configure or design or placement of ACE and FWSM for above scenario.

View 4 Replies View Related

Cisco Application :: Failover ACE / Default Route Redundancy / 6500

Jun 20, 2011

Since the ACE supports only static routing, when pointing a default route from the ACE what is your preferred method when using multiple 6500s with an ACE in each in a failover scenario to prevent just pointing at one 6500? Static route to an HSRP address? Multiple static routes on the ACE, etc?

View 2 Replies View Related

Cisco Application :: Possible To Modify Configure With Snmp On Ace Module Like Others 6500 Catalyst

Apr 12, 2012

Is it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?

View 1 Replies View Related

Cisco Application :: Does 6500 SUP720 / 2T Support MAC Address-Table Move Update Feature

Apr 21, 2013

Does 6500 SUP720/2T support MAC Address-Table Move Update Feature?

View 1 Replies View Related

Cisco Infrastructure :: ACE10 IOS Information Required

Mar 21, 2011

I tried to find the EOL or EOS of the IOS A2(1.6a) of our ACE10-6500-K9 module.what to do ?

View 1 Replies View Related

Cisco Switching/Routing :: ACE10 HTTP Error Page Not Found

Dec 14, 2011

I want to load balance between two webservers using ACE10 working in bridging mode, but when putting the VIP in the url i'm getting page not found, tried many configurations but didn't work, here is the latest one
 
logging enable
logging buffered 7 
access-list ALL line 8 extended permit ip any any

[Code].....

View 4 Replies View Related

Cisco WAN :: QOS Is Not Supporting On 4506 E

Dec 18, 2010

I am trying to configure below commands in Cisco 4506 E with SUP 6 LE but these commands are not not supporting in the switch.Even QOS command is not taking in the siwtch....This was working fine in Cisco 4500 with SUP 2..not i upgared to 4506 E with Sup 6 LE.
  
qos dblqos map dscp 0 to tx-queue 2qos map dscp 16 18 20 22 24 26 28 30 to tx-queue 4qos map dscp 34 36 38 to tx-queue 4qos map cos 3 to dscp 26 qos map cos 5 to dscp 46 qos

View 1 Replies View Related

Cisco WAN :: C6500 Routing One IP Away From Connected Sub-net

Jan 24, 2013

I have lets say a /24 directly connected via a vlan on a C6500 in the network.I'm trying to migrate some servers/devices away from it , however I need to move parts of it away bit by bit ( For example a /32 or a /30  that make up the /24 )Ive tried a direct ip route x.x.x.x 255.255.255.255 y.y.y.y     and even a ip route x.x.x.x 255.255.255.255 y.y.y.y 1
 
Yet it still prefers the directly connected range ( as I pretty much expected. )
 
Is there any way I get it to prefer a static route over a directly connected?

View 13 Replies View Related

Cisco Wireless :: AP Supporting 4402 WLC?

Jun 25, 2012

Can 3600 series model AP work with WLC 4402 with existing license, we purchased 25 LIC pack and still using only 15. Any recommended Part no on 3600 series with external Antenna

View 5 Replies View Related

Server Not Supporting IP Address?

Aug 28, 2012

I just turned my computer IP address changed. I tried to get a uk ip address for accessing some information on internet. But my computer stopped supporting internet server to access it. I got some information from the [URL]... but unable still to find access.

View 3 Replies View Related

Cisco WAN :: Software Requirements For Supporting XFP In 7604?

Jul 15, 2012

We have a 7604 chassis with the following equipments:
 
1. RSP720-3C-10GE
 
2. 7600-SIP-400
 
3. SPA-1X10GE-L-V2
 
 We would like our SPA to support XFP transceiver having  part number XFP-10GZR-OC192LR.

View 2 Replies View Related

Cisco WAN :: 7600 Card Not Supporting Qinq

Dec 5, 2012

I want to do qinq on this card under its sub-interface, unfortanately it doesnt support the command as compared to other ES cards. [code]

View 3 Replies View Related

Cisco WAN :: ASR1002 - Licensing Not Supporting Any Device

Jun 30, 2011

I have recently purchased ASR1002-RP1-ESP5 with 2 x 4K Broadband licenses to be used as LNS. Cisco have sent me PAK files for the licenses however when I try to enter the licenses into the device I get an error message saying that Licensing is not supported on this platform.
 
Any experience with this platform and installation of the broadband licenses?
 
When I spoke to Cisco TAC they told me that for this particular model the licensing is on "trust" basis where you buy license and do not install it on the actual router - similar to what 7200 used to do.

View 1 Replies View Related

Cisco Routers :: Telnet RV016 Not Supporting Cli

Jan 14, 2013

I know this is a small business appliance I got my ccna certification with the hope of practice my CLI skills with a cisco device however I read in cisco docs the small business routers doesn´t support talnet neiter ssh I mean CLI, is thta true ?

View 1 Replies View Related

Cisco :: View (patch 6.1.9) In LMS 3.2.1 Is Not Supporting 1905?

May 2, 2013

Cisco view(patch 6.1.9) in lms 3.2.1 is not supporting router 1905.

View 11 Replies View Related

Cisco :: Using Local User Database As Login To C6500 IOS 12.2

Sep 11, 2012

We are wanting to use local database users to authenticate our SSH connections to our 6500 cores.
 
We have added the usernames and password into the 6500 using
 
username anameduser password astrongpassword or username anameduser secret astrongpassword
 
We where expecting the commands to be the same as other iOS devices example C3750 we would add.
 
Line vty 0 4  login local
 
And this would allow us to use the local user database to authenticate our ssh sessions.
 
The login local commands are not availbe on the 6500s and we have not found any documentation on how to impliment a local database for this purpose except in a CatOS 6500.

View 1 Replies View Related

Cisco VPN :: C6500 Need A Specific Line Card For Tasks

Feb 20, 2012

Im wondering if the Adaptive Security Services Module has some of the same function as a ASA 5500.Can we configure a IPSec VPN tunnel, SSL VPN tunnel or IPS on a C6500 with ASA-SM or do we need a specific line card for those tasks?

View 1 Replies View Related

Cisco Switches :: Supporting SF300 SCP Server On Switch

Sep 9, 2012

How about supporting an scp server on the switch? Makes life much easier for collecting configs and pushing OS upgrades.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved