Cisco Application :: Unable To Access Server Through VIP (ACE 4710)

Oct 3, 2012

configure Cisco Ace 4710 ?Note :- Just a testing face I need to access my one server(192.168.1.11 : 80) through VIP :- 10.13.77.10 ,    I have only one Cisco Router 2800 and One L2 Cisco Switch 2960 and Cisco Ace 4710 . So I already configured 2 Different VLANS in Switch (Vlan 10 & Vlan 100) and by router I given the ip address of that Vlans with Inter Routing Vlan. My Connectivity is like this :-- Router Ethernet 0/0 --- 10.13.77.1/24 with vlan 10) & Router Ethernet 0/1 ---- 192.168.1.1/24 with vlan 100 ) connected with switch after that I configured ACE LB and connect the ACE interface with switch Like that ---- Connect to ACE Interface 2/3 vlan10 with switch vlan10(Ethernet port  2-12) and  Connect to ACE Interface 3/3 vlan100 with switch vlan100(Ethernet port  13-24) .Testing to access server from Switch Vlan10 to Vlan 100 where my server is there.
 
Configuration :---

ACE>  client side Vlan10 (10.13.77.4/24) , VIP :- 10.13.77.10, SM-- 255.255.255.255
 ACE>  server side Vlan100 (192.168.1.5/24), Web server -- 192.168.1.11 with 80 port
 ACE> Managment Vlan 1000 (172.16.6.5/24) ,
 ip  route 0.0.0.0 0.0.0.0 10.13.77.1
 
 I already Configured in Routed mode but From Vlan10 ip subnet example like 10.13.77.12(Client or User PC) tried to access server 192.168.1.11 with VIP http://10.13.77.10 but not responding , if i access server with real IP then accessible (why boz there is inter vlan routing)?

View 22 Replies


ADVERTISEMENT

Cisco Application :: ACE 4710 Unable To Access Through Web Browser

Aug 13, 2012

We have 4710 ACE in our network and currently we are using software version A3 2.0.
  
Currently we are not able to access the ACE through web interface but Telnet is happening properly. Connection is establing while we are doing the telnet to ACE through port 80 and port 443. find the below dummy configuration.
 
resource-class SLB_STICKY
limit-resource all minimum 0.00 maximum unlimited
limit-resource sticky minimum 10.00 maximum equal-to-min

[Code].....

View 12 Replies View Related

Cisco Application :: Access Server Through VIP (ACE 4710) But Very Slow

Oct 30, 2012

Access Server through VIP (ACE 4710) but very slow
 
Accessing the server very slow.., check my real  configuration... this configuration is for application server and after  this i have to configure more serverfarm for different server like  webmail etc. in this ACE 4710. I have only one ACE 4710 .
 
ACE Version A4(2.0) = is there supports Probe with this version?  without probe server will work but very slow.
 
VIP :-- 172.16.15.8  
LB/Admin# sh run
Generating configuration....

[Code].....

View 2 Replies View Related

Cisco Application :: ACE 4710 No Access To Any Server To Do File Transfer

Jan 26, 2013

I ma having issues trying to import a .PEM file into an ACE 4710. The original file was a PCKS12 file that was converted to a set of .PEM files as I have no access to any server to do a file transfer. This has worked in the past. the error I get is "Error: File not of recognized types - PEM, DER or PKCS12, import failed". I am not sure what is exactly failing. The cert was converted to a .PEM and the ACE imported that fine.

View 4 Replies View Related

Cisco Application :: ACE 4710 - SSL Configuration / (HTTPS) Access To Server Farm

Aug 31, 2011

I have been tasked to provide SSL(HTTPS) access to a server farm that will be accessible from the internet.  Is this the correct guide to follow?
 
[URL]
 
I am assuming I will need to purchase a certificate to import into the load-balance r as well.

View 1 Replies View Related

Cisco Application :: ACE 4710 Configuration - Client / IP Address Access For Web Server

Oct 15, 2011

I want to use one arm infrastructure of ACE4710. But I remember it was problem for back end server can not get logging for which client/ip address access the web server.

View 3 Replies View Related

Cisco Application :: ACE 4710 Server In Multiple Server Farms

Jul 23, 2012

I put multiple rservers in multiple server farms?
 
So for example rserver1 and rserver2 are put in serverfarm production1 and are in use with particular sticky and load balancing settings.
 
Can I then create serverfarm test_production and put both rserver1 and rserver2 in it?  Then play around with the sticky and load balancing settings as a test without affecting the production serverfarm.  

View 1 Replies View Related

Cisco Application :: ANM 5.2 Unable To Import ACE 4710

Mar 14, 2013

I am currently experiencing a problem while trying to import multiple 4710 ACE Appliances into ANM. ANM version is 5.2 and ACE 4710 Appliances version is 5.1.2. The error message is the same for all Appliances (currently 14, more to be deployed this year, another 12 this year). The management class, policy-map and service policy are all in place.

View 1 Replies View Related

Cisco Application :: ACE 4710 Take An Action When A Server Goes Down

Jun 2, 2011

If we use an ACE4710 to load balance two real servers, obviously it will use health checks to determine if a server is down.When it detects a server is down, it will not send it any more traffic.But can we also have it take any other action?  For example maybe email an admin, or send an SNMP trap?  Or better yet, can we use a custom TCL script to do other things, like launch some custom activities?

View 2 Replies View Related

Cisco Application :: ACE 4710 SIP - Server Initiated Traffic?

Aug 7, 2012

I have a Cisco ACE 4710 A5(1.2). Scenario: Inbound call from PSTN to SIP Phone. Call comes into the VIP and then load balances to sip server, the server then routes the call out via WAN to the SIP phone as below:

PSTN SIP Providor >(router)> ACE4710 > sip_server(s) > ACE4710 > (router) >SIP Phone
 
Note: Router is Cisco 3925 with "ip nat service sip udp port 5060" and Port 5060 mapped to the VIP of the ACE.If I put the sip server directly behind the router it works fine. From behind the ACE:
 
If I turn on sip inspect on the VIP the call setup (INVITE) and termination (BYE) work fine but the audio loops on the PSTN side from the mic to the speaker.If I turn OFF sip inspect then the audio is fine and mapped correctly but the call terminaton (SIP BYE) hits the VIP from the PSTN but never reaches the sip server.For ease and dianostics, I have turned off all sip servers except one meaning the load-balancer has only one server to choose from.SIP Call_id sticky is setup and seems to work, though irrelevent with one server only on test.How do I get the ACE to accept 'server initiated traffic' with sip inspect so it knows about the pending BYE when it comes back from the IP phone via the VIP?Config below, image attached. Bridged mode (also get the same result in routed mode)
 
access-list everyone line 8 extended permit ip any anyaccess-list everyone line 16 extended permit icmp any any
probe sip udp 1  description SIP Health Monitor  interval 30  expect status 200 200
rserver host server1  description Production SIP Server  ip address 10.44.56.172  conn-limit max 980 min 980  probe 1  inservice
serverfarm host sip  failaction purge  probe 1  rserver server1    inservice

[code].....

View 7 Replies View Related

Cisco Application :: ACE 4710 - Renaming Server Farm

Feb 2, 2012

Is there a way to rename a server farm, health probe, real server or virtual service without having to completely rebuild it?  I'm running 3.0(A3).

View 2 Replies View Related

Cisco Application :: ACE 4710 Server Load Balancing?

Jul 7, 2012

We have two Cisco ACE 4710 and we want to install both of the devices in HA with load balancing mode.While i have done HA mode configuration between ACE 4710.But unable to configure load balancing configuration between them.i want to tell you connectivity between server,client & loadbalancer.Our Web servers are connected to VLAN 152 on the L3 (3750) switch.Which are alreday working in redundancy between other L3.And ACE 4710 it is also connected to vlan 150 which are connected to same L3 (3750) switches and users are also connected to vlan 6 on the same L3 itself. 

View 2 Replies View Related

Cisco Application :: SNMP Server Not Receiving Traps From ACE 4710

May 24, 2012

Had setup my ACE ,to send traps to SNMP server .but dont see any logs on the SNMP server from ACE.
 
SNMP configuration on ACE 
 
logging enable
logging buffered 6
logging host 10.12.40.12 udp/514

[code].....

View 1 Replies View Related

Cisco Application :: ACE 4710 - Monitoring Real Server Showing N / A?

Jun 25, 2012

I recently installed a Cisco ACE 4710 version A4(2.0) into our test network. Load balancing across a number of web servers appears to be working ok and serving pages to users. However, when i tried to check the real time stats via device manager (Monitor> virtual contexts> context > Real servers) a number of fields specifically "current connections", "total conns", "failed conns" etc were showing N/A. Do I need to enable this somehow i.e. polling, if so how?

View 5 Replies View Related

Cisco Application :: ACE 4710 / Sticky Serverfarm / All Connections On One Server?

Nov 2, 2011

We are using a sticky serverfarm with 2 real servers, one server was down for maintenance for an extended period of time. When it came inservice again it was not getting any connections. is it because all the connections had stuck to the other server ?  we want sessions to be sticky but we also want to LB?I got it working by bouncing the server that had been online all the time. things started to LB then.BTW  the ACE 4710 is running 4.2.1

View 1 Replies View Related

Cisco Application :: Importing SSL Certificate From MS Exchange Server To ACE 4710?

Nov 16, 2011

My customer has SSL certificate already installed on microsoft exchnage 2010 servers and now wanted to import that certificate to cisco ACE4710.
 
How to trace the exact procedure to import the SSL Cert to ACE from microsoft exchange server and how about the KEY, from where I should get the KEY to cross verify for SSL Cert?

View 2 Replies View Related

Cisco Application :: ACE 4710-K9 - VIP Not Showing Webpage From Real Server

Mar 27, 2013

my ACE 4710-K9
 
I cannot reach a web page when accessing my VIP on ACE, here is i paste my configuration
 
VIP at 10.49.30.223
RS1 at 10.49.30.221
RS2 at 10.49.30.221

[Code].....

View 8 Replies View Related

Cisco Application :: ACE 4710 - Configuring Backend Server Monitoring?

Apr 6, 2013

Currently running an ACE 4710, which is handling all of our inbound SSL connections and then forwarding requests thru to backend web servers. This all works fine.
 
My question is this..Right now we are not load balancing any of the backen web servers. But I now have a requirement that should a web server crash or become unavailable I need to redirect that backend connection to another web server.
 
Scenario is more like I have 2 web servers both serving same content, but I want one server to take all the connections unless it fails, at that point have all the connections forwarded to 2nd server.Is there a way to setup the load balancing where the 1st server gets all the connections until a failure happens ?

View 1 Replies View Related

Cisco Application :: Unable To Make Call MS Lync To CUCM If Using ACE 4710 LB

Sep 15, 2012

We have CUCM & lync server setup and its working fine if any one calling each other with DNS load balancing. But customer want ot use Cisco ACE 4710 instead of DNS LB.We have configured Cisco LB and deploy but when CUCM user calling to lync user call going to disconnect after 4 sec and also Lync users unable to make call to CUCM.And also LB deploye between share point but when users are trying to open web session that time web page going to show page cannot display.
 
[code]....

View 1 Replies View Related

Cisco Application :: Configuring Load Balancer (ACE 4710) - Unable To Ping VIP

May 13, 2013

I have trouble with new installation  LB ACE 4710 for Oracle application load balance. Problem: Unable to PING VIP - 10.11.10.55 / 24
 
Below are the simple configuration parameters:

1. ACE 4710 is connected with Cisco 3560 Switch - L2 Trunk (Channel Group)

2. Cisco 3560 Switch is connected with Cisco 6500 Switch (Core) also L2 Trunk

3. There are 3 Vlans,(255, 310, and 370), Vlan 255 is management Vlan

4. Real Servers and Virtual IP are part of Vlan 310
- VIP  - 10.11.10.55
- Real Server1 - 10.11.10.46
- Real Server2 - 10.11.10.47

5. Gateway is 10.11.10.1 (vlan 310), 10.11.70.1 (Vlan 370)

View 5 Replies View Related

Cisco Application :: ACE 4710 Load Balance Only If Primary Server Fails

Oct 14, 2012

I've done a lot of ACE work over the years but this is the first time this has ever come up. 
 
I have a request from an application group where I have 3 rserver in the server farm but they want all traffic to only go to the first server unless that server fails.  If the first server fails, only then do they want traffic to go to the 2nd server instead and if that fails, then traffic goes to the 3rd.
 
I've read through the documentation but haven't figured out a way to do this. What to do this type of failover configuration?

View 4 Replies View Related

Cisco Application :: Change Version In ACE 4710 To Support NTP Server External?

Oct 26, 2011

I´m Trying to synchronize the clock with NTP server external, these ntp server only support NTP version 3.Can I change the NTP version in the ACE4710 Appliance to support the ntp server external?If is possible, How I can change it ?
 
 This is the version:
 
Cisco Application Control Software (ACSW)
TAC support: [URL]
Copyright (c) 1985-2011 by Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.

[code]....

View 1 Replies View Related

Cisco Application :: ACE 4710 Server Farm Fail-on-all Option Missing

Feb 27, 2012

ACE 4710 software A3(2.7) [code] Why is the fail-on-all option missing from the serverfarm that is of type redirect? This option is something that I would actually need in a certain situation.

View 1 Replies View Related

Cisco Application :: ACE 4710 Prevent Failback To Primary Server When Probe Fail

Feb 26, 2011

I want to configure my ACE so that if a probe fails, it fails over to the backup rserver, BUT it won't failback to the primary rserver until manual intervention is complete. The problem is we don't want an rserver to fail and failover to secondary, then failback to primary, repeat... (flip-flopping).   I want to be able to have time to get on the server and find out what may have caused the probes to fail before it fails back.

View 4 Replies View Related

Cisco Application :: ACE 4710 GUI Access Is Not Working

Jun 1, 2011

We have Cisco ACE 4710 in our network.system image file: (hd0,1)/c4710ace-mz.A3_2_0.bin  Device Manager version 1.1 (0) 20080805:0415   
 
We are not able to connect to the device through HTTPS (GUI) , it used to work before. When we try access the GUI, it asks for user name and password.After that it shows blank screen.

View 2 Replies View Related

Cisco Application :: ACE 4710 - Cannot Access Management VLAN In Context

Jan 21, 2012

I have an HA ACE deployment and all seemed to be working well until I tried to access the ACE via the management VLAN in the one non-system context, no go.The ACE is in one-armed mode with an Admin/System context and one user context (named Messaging).  Source NAT has been set up in the user context.  All VLANs are in a port channel back to the core switches.I can access the ACE via the Management VLAN in the system context, all OK.  I can access the load-balanced servers via the VIP in the user/Messaging context, all OK.  I CANNOT acccess the managment VLAN other than ping it (resonds to ping, but telnet, ssh, https, etc. fails).The system/Admin context has a default route to the Management VLAN on the core.  The User/Messaging context has a default route to the core switches on VLAN 5, which is the VLAN where the VIP resides.If I change the default route in the User/Messaging context to the Management interface on the core switches then I can access both contexts for management, but then the load-balancing falls over and I cannot access the serverfarm (via the VIP).  Traces on the rservers show that NAT is being hit on the ACE and the requests are coming from the real IP of the clients.  Put the default route back to the User/Messaging VLAN on the core and NAT is back to what it would be expected to be, and then remote/management access to the ACE is gone.
 
ACE02/Admin# sh run

Generating configuration....
 
logging enable
logging standby
logging timestamp
logging buffered 4
logging device-id context-name

[code]....

View 1 Replies View Related

Cisco Application :: ACE 4710 Giving Mangled Http Requests In Apache Access

Oct 21, 2012

After replacing a Cisco CSS/SSL  Accelorator and PIX firewall with an ACE 4710 to do load balancing and  SSL encryption behind an ASA firewall we started seeing mangled HTTP  requests in the Apache access logs for the servers in the server farm. This is occurring for several different URLs and not just the one above and for multiple web browsers.The ACE load balances to servers running Tomcat 7 with Apache HTTP server v. 2.2.14. A recent ACE software upgrade to A5(2.1) has not fixed the problem.

View 1 Replies View Related

Cisco Application :: ACE 4710 To Setup User With Admin Context Access Permission

Jan 12, 2011

ACE 4710 TACACS issues ,How to setup user with Admin context access permission. I have enable the TACACS and it can directly put me in Context mode not in Admin Context mode .

View 8 Replies View Related

Cisco Application :: Application Slowness Through ACE 4710

Mar 27, 2013

Report run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.

View 6 Replies View Related

Linksys Wireless Router :: EA6500 Unable To Select Folder Access / FTP Server / Media Server

Dec 9, 2012

I purchased the EA6500 a few days ago, and when I'm connected to Cisco Connect Cloud I am unable to select Folder Access / FTP Server / Media Server.  I click them and nothing happens.Also, the Cisco light on the router keeps blinking.

View 5 Replies View Related

Cisco Application :: How To Install New 4710 Ace

Feb 2, 2013

i'm looking for a recommendation for a setup guide including ft i've had a quick look a wiki and i can get basics but i'm not sure about if i need to setup additional contexts etc when i'm the only one using the appliance?

View 2 Replies View Related

Cisco Application :: DNS Rewrite On ACE 4710?

Aug 26, 2012

I have an issue with a customer that wants to update a server behind the ACE. The problem is that when the application wants to update the server it does it with the name.Doing some research I found that you can rewrite the record DNS based on the static NAT you set up on the ACE. The feature is called DNS inspection. Is the same feature as the ASA (DNS doctoring).I apply it to the outside interface and it did not work.

View 1 Replies View Related

Cisco Application :: ACE 4710 / What Are These Ports Used For

May 7, 2013

What are these ports used for? What can I do with them?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved