Cisco :: Can't Ping From Inside To Outside Host?

Jul 6, 2011

configure my Cisco ASA5510 (asa version 8.3.1) so that one of the host (e.g.192.168.8.20) behind management interface can ping to the other host (e.g. 192.168.2.246) behind OUTSIDEinterface. I tried modifying the ACLs, NATs and ICMP statement, but still failed[CODE]

View 19 Replies


ADVERTISEMENT

Cisco Firewall :: ASA5505 - Can't Ping Inside Host

Sep 29, 2012

I just try to ping a internal Host but it want to go.
 
Laptop<===>ASA5505
 
Connected is the Laptop at Ethernet 0/2 Inside
 
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
 
But If I try to ping to the Laptop I get the followed:
 
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
 
From the Laptop to the ASA5505 I can Ping successfully.

View 6 Replies View Related

Cisco Firewall :: ASA5505 Cannot Ping Inside Host

Aug 2, 2011

I have Cisco ASA 5505  installed  and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM  and the VPN Tunnel is not working between the sie
  
ASA# ping 10.10.10.12
???????????
100% lost 
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
 
Here is the Topology
 
INTERNET .<=========================>ASA<===============================> LAPTOP
  
I disabled window firewall on the Laptop , but no goof result.

View 3 Replies View Related

Cisco Firewall :: ASA 5520 - PING From Outside Into Inside Host

May 13, 2013

I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226".  Is it because I used dynamic PAT for inside hosts?

interface GigabitEthernet0/0nameif outsidesecurity-level 0ip address 198.24.210.230 255.255.255.248!interface GigabitEthernet0/1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0

[Code].....

View 3 Replies View Related

Cisco Firewall :: Unable To Ping Host From Inside Interface From PIX525

Feb 3, 2012

When I tried to upgrading PIX525  6.3 to  7.0 , Not able to Ping the host from the PIX 525 Inside interface  which is on the same subnet,  Also from the host to Inside Interface ,  Tried with Directly connected  laptop with Cross cable and using Straight cable via switch, But the  results end with fail.

View 2 Replies View Related

Cisco VPN :: Pix 515e - Remote Host Cannot Ping Any LAN Host

Jun 27, 2011

I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.

View 2 Replies View Related

Cisco VPN :: ASA 5510 Ping / Communication Host To Host

May 7, 2012

ASA 5510
Ver 8.2(5)
 
I have been looking all over the place for the answer of how to allow clients on an IPSEC VPN to ping from host to host.

View 4 Replies View Related

Can Pure IPv6 Host Ping A IPv4 Host?

Feb 10, 2011

I'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...

View 2 Replies View Related

Cisco WAN :: 2811 - Cannot Ping Inside Global IP From Inside Network

Dec 18, 2010

I have 2 questions.Om my cisco 2811 (IOS 12.4(15) T9 IPBASE W/O Crypto) i am using 3 interfaces.And i have a pool of Global addresses: 200.x.z.97-200.x.z.126 255.255.255.0
 
FastEthernet 0/1 description WAN interfaceip nat outsideip address 200.x.y.253 255.255.255.0
 
GigabitInterface 0/2/0description DMZ interfaceip nat insideip address 10.0.0.1 255.255.255.0
 
GigabitInterface 0/3/0description LAN interfaceip nat insideip address 192.168.0.251 255.255.255.0
[Code]....

View 8 Replies View Related

Cisco Switching/Routing :: Can Ping From R1 To R3 SVI4 Gateway But Cannot Ping Host

Dec 12, 2011

I set this up and I can ping all the gateways but never the hosts.  I was hoping I could make these links between 6500's a mix of L2 and L3.  Check it out.  They are connected in a linear fashion R1--->R2--->R3.  I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4.  I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration.  I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.

View 3 Replies View Related

Cisco Firewall :: ASA 5505 - Allow (outside) Host To (inside)

May 20, 2011

I have a ASA 5505 Sec Plus. I would like to allow outside hosts to our mail server and also our FTP server. So i would like to allow only SMTP, HTTP (for Outlook Web Access) and FTP.

View 10 Replies View Related

Cisco Firewall :: ASA (8.4) / Redirect Outside IP Request To Inside Host

Mar 27, 2012

Wondering if on the ASA (8.4) its possible to do something like what DNS rewrite does, but with IP requests.  Scenario.  Mobile phone accesses a web app inside our network fine over cellular.  Once it comes inside on to wifi it still has the public IP address cached so the ASA doesn't allow its request to loop around and the app appears broken.  We're considering lowering the TTL on the DNS host entry but I think we are battling phones/mobile OS's that don't have a strict adherence to name resolution standards.  A lot just seem  to refresh their caches every 10-15 minutes.

View 4 Replies View Related

Cisco VPN :: 3745 - Can't Reach Inside Host After Connected To ASA

May 31, 2011

I am having problems accessing our internal network via VPN. We have an ASA at the perimeter that connects to a 3745 router and all of our networks come of that router. I can establish a VPN connection to the ASA but I can’t ping any of our internal host.
 
The internal network I need to access is 172.18.0.0. When I connect to the ASA I get a dhcp address from a pool created in the ASA, the pool is 172.200.1.x. I can’t ping from the ASA to the connected vpn host and I can’t ping from the host to the ASA ip address or to 3745 connected to it.
 
ASA config: 
group-policy NAMEOFPOLICY internal
group-policy NAMEOFPOLICY attributes
dns-server value 172.18.2.2 172.18.2.23

[Code]....

route inside 172.18.0.0 255.255.0.0 172.18.255.1 1 Route on the 3745 back to the ASA ip route 0.0.0.0 0.0.0.0 172.18.255.2 I can’t see anything on the internal network, I can’t even ping the dns servers and so on.

View 3 Replies View Related

Cisco Firewall :: ASA 8.4 - Connection Fails When Host On Inside Tries To Connect To Server On Outside

Mar 9, 2011

We are using an ASA with 8.4 in transparent mode. Connection fails when a host on inside tries to connect to a server on outside. This server uses mac-address 0100.5E00.0000 to load balance but replies with real mac-address.Firewall logs "Deny TCP".ARP inspection is disabled.

View 2 Replies View Related

Cisco Firewall :: 5520 - Inside Server To See Actual Outside Host Source IP In Udp Packet

Mar 3, 2013

I have a 5520 in production at a customer's site between an outside 802.11 network and an inside server.   The server can get to outside hosts OK, and the traffic is being NATed  properly, and sockets initiated by the server on the inside can pass data both ways, but I need to allow outside hosts the ability to send  'announcement' UDP packets to the inside server.  I thought this might be an  outside-NAT-required issue to get the traffic routed, but I need the inside server to see the  actual outside host source IP in the UDP packet, so I basically set the  outside host up similar to the inside host, just without the NAT table on the firewall -- it's subnet is outside the  destination (inside server) subnet, and its gateway is the outside  interface of the ASA, the same way the inside server is able to get to  hosts outside.  The firewall should just route the packet with a destination of the inside subnet once it sees that it hits a 'permit' ACL.
 
I have the appropriate ACL's set up, and when I do 'show access-list' I  see policy hits for the 'permit' statements where the outside host is  generating the announcement and it's hitting the ACL.  I even duplicated  the ACL into list 101 and 102, and applied 101 for inbound traffic on  the outside int, and applied 102 for outbound traffic on the inside int,  and I'm seeing policy hits on both permit statements outside and  inside, so it looks like the traffic is being passed on to the inside  interface and permitted, but the server isn't seeing the packets.
 
I can ping the outside interface from the outside, but cannot ping the  inside interface or any inside hosts from the outside, even though I  have 'permit icmp any any' enabled on the ACL on both ints. When I  remove the firewall and put the outside clients on the same subnet, the server sees the packets just fine.
 
I set up the same scenario in my lab with an ASA 5505, with the same results.  Below is the running config from the 5505 in the lab.  The production firewall is running a slightly older version of ASA, so I made the configuration as basic as possible on the 5505 to match the config in the field:
 
: Saved
:
ASA Version 8.3(1)
!
hostname ciscoasa
enable password Guh9Xxhb9mcC8lV1 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan2
description Outside WAN Interface
nameif outside
security-level 0
ip address 192.168.10.1 255.255.255.0
!
interface Vlan3
description Inside LAN Interface
nameif inside(code)

View 6 Replies View Related

Cisco WAN :: 871 Can't Ping From Host

Jun 30, 2012

I'm going through the CCNA training and I'm setting up my DHCP server on my 871 router. I have my cable modem into the WAN port on my router and have 1 host plugged directly into Fastethernet 1. I can ping any IP I want from the IOS prompt but I only have local access from the host. [code]

View 4 Replies View Related

Cisco :: Can't Ping From Outside To The (online Host) PC

Aug 26, 2012

I tried to ping from the "online host" PC to the outside,it succeeded. However, I can't ping from outside to the "online host" PC.

View 2 Replies View Related

Cisco :: Can't Ping From ASA To Host In GNS3

Apr 24, 2012

I test all devices using ping command, from ASA to router was fine (on both interface) but not to Host , and host to router was fine, but only on directly interface(F1/0), and to ASA was not success. am i miss something in my configuration?

View 5 Replies View Related

Ping From Host To Guest With NAT?

Jun 27, 2012

I have installed an Oracle DB (11.2) on a guest VM (Centos 5) and my host is Windows 7 Ultimate.I need to able to connect to the DB from windows.Ping status is as follows:

guest -> host - IP : Yes
guest -> host - hostname : Yes
guest -> guest - hostname : Yes
guest -> guest - IP : Yes

[code]....

View 5 Replies View Related

Cisco WAN :: Cannot Get ASR 1002 To Ping On Interface To Host

May 12, 2013

I have a cisco ASR 1002 I have plugged a host into an addressed port and the port comes up however the host cannot ping the router and the router cannot ping the host. Neither can router ping its self. I do the same on a cisco 2800 router and it works fine. What's goin on. Is it the fact that this is a ASR router ?

View 5 Replies View Related

Cisco :: 1140 APs - No Ping To Host From Local LAN

Apr 3, 2013

I'm using 3 AP's 1140 with local authentication using local radius (flex connect mode).the radius server im using is MS 2008 R2.authentication is working great on all devices pc's&mobile.authentication method is PEAP wpa2 aes enterprise.after 3 or 4 hours devices loose connectivity to the web.the device seems to be still connected to the ap but there is no ping to host from local lan or any arp learnd on local router.only manual disconnect on device and reconnecting brings connectivity up again.in one case only reseting the AP's worked.

View 6 Replies View Related

Cisco Application :: 11503 Ping For One Virtual Host

Apr 27, 2013

I have a single  cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group  ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the  the content Erp_IAT active  it stops pinging. [code]

View 6 Replies View Related

Can't Ping / Connect Ipv6 Host On Windows 7 Vs XP

Apr 27, 2011

When I try to ping ipv6.xsnews.nl on either of my Windows 7 computers, it returns "Ping request could not find host". But when I do it on XP, it succeeds. I have tried putting the W7 PC in the DMZ, disabling the software firewall but it doesn't work.

What I think it involves is having ipv6 installed on each. I tried to duplicate the setup of both the XP and a W7 computer, installing the gogo6 tunnel. But apparently it's not setup on this computer because the ping result is the same as on the third computer which hasn't had ipv6 installed. s not setup on this computer because the ping result is the same as on the third computer which hasn

View 3 Replies View Related

Cisco :: ASA 5510 Ping Between Inside Interfaces

May 4, 2012

I have two inside interfaces (both security level 100) inside and inside110. Inside is 192.168.105.3/24 and inside110 is 192.168.110.3/24. I have a PC on the 192.168.105.0/24 network. I cannot ping the 192.168.110.3 IP of interface inside110.

View 2 Replies View Related

Cisco Firewall :: Cannot Ping To Inside Hosts From ASA-8.2

Jun 8, 2013

I am struggling to get successfull pings beween asa and inside hosts but couldn't succeed. Done packet tracer result is acl-drop
 
Here is the running config
 
Prem-ASA(config)# sh run
: Saved
:

[Code].....

View 7 Replies View Related

Cisco Firewall :: ASA5510 Cannot PING From Inside To Outside

Jul 1, 2012

I cannot seem to determine exacly why I am not able to ping from the inside to outside using the standard 100/0 security levels respectively. I am dynamic natting the inside to the outside interface, something I don't usually do but cannot see why ICMP's are not passing through.
 
The Packet trace tool says there is something in the ACL but there really isn't.
 
Is there simply an issue of Natting to the WAN interface on a 5510?

View 10 Replies View Related

Cisco VPN :: Can't Ping Inside Interface Of 5510

Sep 19, 2012

I have recently installed an ASA5510 at a site in South Africa to connect via VPN to a site in the UK (ASA5520).  The VPN comes up fine with the 5520 in the UK, however, I can not connect to the inside interface over the VPN, but can access it from the internal LAN.  All other hosts on the LAN are accessible over the VPN.
 
The 5510 also has another VPN to another site in SA and the 2nd site cannot ping the interface either.

View 10 Replies View Related

Cisco WAN :: ASA 8.4 Can't Ping External Hosts From Inside

Jun 9, 2011

DNS resolution works and I can surf the web without fail.  But if I try to ping any external hosts (I can ping inside interface of ASA fine) from the LAN I get timeouts.  I can ping anything from the ASA without fail.

ASA Version 8.4(1)
!
hostname fw1-nat-ann
domain-name inmd.infoblox.com
enable password anWLNen9CTFp7B/X encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Ping Inside To Outside Don't Go

Sep 29, 2012

I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
 
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
 
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
 
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254

View 2 Replies View Related

Cisco Firewall :: NAT ASA 9.0(2) / Cannot Access Original IP Using Another Port Or Ping From Host

Apr 10, 2013

Basically after upgrade from ASA 8.4 to 9.0 (2) I have problems when certain types of NAT.Example:SA 8.4: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http while other ports can be accessed using the original IP (10.252.253.123).

ASA 9.0:      nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http but unlike before now I cannot access to the original IP (10.252.253.123) using another port or ping from host 192.168.3.2.

View 12 Replies View Related

Cisco WAN :: 1941w AP Can't Ping 2nd Router / Host But Interface Reachable

Feb 2, 2013

From the router I can ping the 2nd router, all its host and all of the 1941w interfaces.
 
From the 1941w AP i cannot reach the 2nd router or any of its host, but I can reach the interface that is connected to the 2nd router but only one side of it.
 
Attached are both my router and ap configs. At the moment I am just trying to reach the 2nd router and its host so I can update the AP IOS image but cannot reach the tftp server.

View 5 Replies View Related

Cisco VPN :: 2611xm - Unable To Ping Remote Host Through Tunnel?

Apr 20, 2012

I am in a test environment using an ASA 55005 and a Cisoc 2611xm router. ASA is running version 8.4 and router is running is ios12.4. My VPN tunnel comes up but I am unable to ping between remote hosts. I used the ASDM and SDM for the configuration. Attached is a copy of both configs.

View 8 Replies View Related

Ping Could Not Find Host / DNS And Key-port / Server Not Found

Apr 30, 2011

recently I had some malware on my Windows XP Professional (version 2002), so I followed a guide at Bleeping Computer [URL] to get rid of it. Problem is, for some reason, after I finished, I could no longer access the internet!When I try, FIrefox gives me their "could not connect" message: "Server not found. Firefox can't find the server at [site]." Check the address for typing errors such as ww.example.com instead of [URL]"When I try to log into MSN, the troubleshoot says I have a problem with my DNS and Key Ports.I'm not good with computers so I Google'd and found some ping-ing instructions. When I tried to ping [site], I get: "Ping request could not find host [site]. check the name and try again." This happens regardless of the site I use.Lastly, I tried "ping 127.0.0.1" from a troubleshooting site. It gives me: "Pinging 127.0.0.1 with 32 bytes of data:

Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128

[code]..

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved