But when I telnet to the device and run a "show env temperature status" I get:
# show env temp status
Temperature Value: 32 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 51 Degree Celsius
Red Threshold : 61 Degree Celsius
So I'm not sure why I am getting a "1" when using snmpget on the OID 1.3.6.1.4.1.9.9.13.1.3.1.3.1005 which is (ciscoEnvMonTemperatureStatusValue)??
If I run the same OID on another 3560G Router I get the correct output from snmp....
I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
how to safely remove the WiSM2 from the Catalyst 6500 series switch? According to the documentation "Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note":
To remove the WiSM2, perform these steps:
Step1 Shut down the module by one of these methods: In privileged mode from the router prompt, enter the hw-mod module mod shutdown command. NoteIf you enter this command to shut down the module, you must enter the following commands in global configuration mode to restart (power down, and then power up) the module: Router# no power enable module modRouter# power enable module mod If the module does not respond to any commands, press the SHUTDOWN button located on the front panel of the module.
Step2 Verify that the WiSM2 shuts down. Do not remove the module from the switch until the POWER LEDis off.
But, in the case of Step1 (1st methods) I do not see a option "shutdown" in the command "hw-mod module 3"...
All I prompted to enter is: c6500#hw-module module 3 ?
boot Specify boot options for the module through Power Management Bus control register
reset Reset specified component
simulate Simulate options for the module Is it hidden options?
IOS version of c6500 is 12.2(33)SXJ1
In the case of Step2 (2nd methods) there is not any button on the front panel of the module?
And yet, it is better to remove the module configuration manually or use the command module clear-config prior to removing the module?
I want to limit the bandwidth of my Catalyst 3750 series switch, I read the cisco documentation and I applied the commands but I didn't get the wanted results.
For the outbound traffic it's ok, but for the inbound traffic I used policing but I get an unstable traffic. I used, an access list and a class-map to classify the traffic and then a policy-map.(I followed the steps mentioned in this site: [URL]
Any explanation regarding these different operating temperature ranges? I would think it doesn't matter the enclosure that the switch is in, it will either work or fail at a certain temperature.,-40C to +70C (Vented Enclosure Operating),-20C to +60C (Sealed Enclosure Operating), -34C to +75C (Fan or Blower equipped Enclosure Operating).
a customer purchased a ESW-520-24p to be used in a VoIP project. Today we had difficulties connecting it to a Catalyst 3650G switch; We've tried setting the port to trunk, general, customer and access and changed all sorts of VLAN settings on the 3560G switch to no avail: the switches just wont interconnect. While sniffing we saw that ARP requests are even not answered, so something is wrong on a low level, probably with VLAN-ing.if these switches should be able to be interconnected and if yes, what needs to be done to do so?
Secondly; voice will be on seperate VLAN and the client will use SPA942 phones, which have an internal switch that allows to connect a PC to it. I've used this phoned successfully with Catalyst Express switches and I didn't have to do anything for VLAN-ing, this worked "out of the box". Can these phones work with the Small Business switches as well?
We have 2 catalyst 3560g-48-PoE protected by a 1000Va 800Watt tripp-lite and I was cheking to see if that is really sufficient. Looking at the charts from Cisco suppport I would think I should have more, but have not had any issues with a few power outages
I have three VLANS set up on my Catalyst 3560G switch. Each VLAN has its own subnet and I have enabled IP routing and set up my VLANS so that clients on VLANS 1 and 3 can get to VLAN 2 because they share a server located on VLAN 2. However, now they can also see and get to each others VLANS! How I can allow my clients on VLANS 1 and 3 access a server on VLAN 2 but not access the other VLANS? I don't want VLAN 1 to get to VLAN 3 or VLAN 3 to get to VLAN 1.
to resolve a problem with L2 etherchannel -when I add VLAN on Portchannel, this VLAN does not appear in config Members of this Po, so after reboot Portchannel does not work: "...and will be suspended (vlan mask is different)"
I try to simulate it on test switch in office, but problem does not appear! Both switch are Catalyst3560G with same IOS.
1. SW in real network segment:
Model revision number : D0 Motherboard revision number : B0 [Code]...
I am trying to implement static route tracking on a Catalyst 3560G ( WS-C3560G-48PS, IOS version 12.2(35)SE5 and SW image C3560-IPBASE-M). The configuration is as follows:
track 101 rtr 1 reachability ! rtr 1 type echo protocol ipIcmpEcho 10.199.101.2 rtr schedule 1 life forever start-time now ! IP address 10.199.101.2 is reachable via ICMP (its the next-hop router).
The static routes configured are the following:
ip route 0.0.0.0 0.0.0.0 10.199.101.2 track 101 ip route 0.0.0.0 0.0.0.0 10.200.52.1 20
But only the secondary route(ip route 0.0.0.0 0.0.0.0 10.200.52.1 20) its being installed on the routing table by the switch.
I would like to get the temperature status from this 2960 switch (and several other models. Normally this OID should be:.1.3.6.1.4.1.9.9.13.1.3.1.6 But it does not return anything.
The termperature status can be found from the command line by running:"sh env temp" This reports back ok, so I assume there is a temperate gauge in the switch.
This oid is part of the "CISCO-ENVMON-MIB" mib and accouding to the Cisco MIB selector it is supported on my switch and IOS - 12.2(25).
(Another thing I woudl like to monitor and should be supported is the fan status oid (.1.3.6.1.4.1.9.9.13.1.4.1.3). That doesn't return anything either.
What do I need to do to get the temperature environment status from SNMP query?
The Linux Router and the 1811 have formed a PIM neighbor relationship. The multicast listener sends an IGMP Join and I can see the PIM join leave the 1811 router (via "debug ip pim"). Using tcpdump on my linux router I never see the Join come in, but I can see the PIM Hellos (which is why the neighbor relationship formed).
i facing problem with my switch cisco 3560G, when it power on only System light is green and noting happen. i check with serial cable ( Console) but noting happen no booting.
We have a Catalyst 3560G 24 port POE switch. It's been running fine for 1+ years. A few weeks ago we enabled SPAN on it to capture packets. Today, we had a random spike in CPU on the switch. Seems hardware swithing continued to work fine, but software based processes choked and effectively took down EIGRP, HSRP, etc. We collect syslogs from the router and we saw 2 crashes/reboots. Both showed the exact same error both times, with the same hex values. I **believe** the CPU usage dropped when a tech disconneted the SPAN port and it's state changed to down, but I'm not 100% sure.Could this indicate an IOS bug (I'm hoping it's not a hardware failure)? And, how to track this down to see if this could be related to SPAN? I've disabled SPAN for now.
We have two 3560G-TS-E running 12.2(35)se2, configured as HSRP. Both are running ntp config "ntp peer 210.72.145.44" and it's pretty well that they get the correct time. Yesterday I upgraded the second device to IOS 12.2(58)se2 and ntp doesn't work now. I checked doc that 12.2(58)se2 runs ntp default version 4 so I change to "ntp peer 210.72.145.44 version 3" but still not work. I put here "show ntp" result for different IOS.
IOS 12.2(35) SW01>show ntp status Clock is synchronized, stratum 2, reference is 210.72.145.44 nominal freq is 119.2092 Hz, actual freq is 119.2022 Hz, precision is 2**18 reference time is D2EF12A5.2EB2DCB2 (15:07:17.182 GMT Wed Feb 22 2012) clock offset is -4.6616 msec, root delay is 57.50 msec
I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
Configuring OSPF on a catalyst 3560G Switch to connect to our building next door by way of fiber. The other two switches in the other building are running OSPF, I am trying to connect to the other building and access a server which is on a switch running OSPF. I am trying to configure the switch here to run OSPF and be able to see the neighbor, but currently can't although I've identified the networks. Maybe I'm missing something, I've followed the instructions but something is not right.
My issue: I have installed a firewall within my network. Currently all my clients default gateway defaults to GW:192.168.1.1. I would like all my internet traffic to route to the firewall ip 192.168.1.30. My Primary switch ip is 192.168.1.10, which is a 3560G running 12.2(25)SEE2 IPBASE-M.
My main problem is, I do not have access to the gateway, so I am trying to route internet traffic from within my switch to the firewall. I have already tried Route-Map, but seems this version of the OS does not support. I have already tried Policy-Map, but same as above. I have also tried IP ROUT command, but it did not work either.
And remember, I would like to perform the routing from the switch, because I do not have access to the default gateway which is a router to perform forward internet traffic to the firewall.
I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
I inadvertantly copy the wrong image on to a 35609-X switch and now it gets stuck in a particular mode.
The original image was: c3560e-universalk9-mz.122-53.SE2/c3560e-universalk9-mz.122-53.SE2.bin and I replaced it with: c3560e-universalk9npe-mz.122-55.SE1.bin ( this is what the download site identifies as the image for 3560X-24P-S)
It now sticks at: Front-end Microcode IMG MGR: Programming device 0...rrrrrrwssssssssssssssssssspssssssssssssssss
How can I get back on to delete this image? It ignores the break key.
I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
I have a strange issue with 4500 E chassis loaded with SUP 7L-E which always remains in ORANGE LED status, also the uplink ports interface is down and the line protocol is down but when i execute the command sh int gig1/5 it show me the media type sfp but there is no red laser light seen in the sfp transiever,The below command is configured for the uplink gig port on the SUP engine.hw-module uplink select gigabitethernet?
it seems that i made a mistake when typing the BAUD rate of a 2960-Switch in rommon.I can't start the switch now, because there is no image on it (because I deleted it before) and the baud-rate has wrong settings. When connecting via console cable i can't see anything (except some strange hieroglyphics) when starting. I tried all the speeds in teraterm... without success.what can i do, to recover the switch back?
