one of my SNMP server 10.242.103.42 sits in MZ zone,and ACE 4710 is connected to core switch,coreswitch is connected to firewall asa.
Now iam trying to ping from MZ zone SNMP server to loadbalancer ip 10.242.105.1,iam unable to ping my LB interface to discover SLB on my SNMP server.
One of my client has BSNL leased line with LAN IP POOL we configured those on ASA 5510 nad Internet working fine but from cloud we are not getting any response for ping requiest please find running configuration below:
ciscoasa(config)# sh run
: Saved
:
ASA Version 8.2(1)
[Code]....
I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1).
ASA Version 8.4(1)
!
hostname FW5520
[Code].....
When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies View RelatedI have trouble with new installation LB ACE 4710 for Oracle application load balance. Problem: Unable to PING VIP - 10.11.10.55 / 24
Below are the simple configuration parameters:
1. ACE 4710 is connected with Cisco 3560 Switch - L2 Trunk (Channel Group)
2. Cisco 3560 Switch is connected with Cisco 6500 Switch (Core) also L2 Trunk
3. There are 3 Vlans,(255, 310, and 370), Vlan 255 is management Vlan
4. Real Servers and Virtual IP are part of Vlan 310
- VIP - 10.11.10.55
- Real Server1 - 10.11.10.46
- Real Server2 - 10.11.10.47
5. Gateway is 10.11.10.1 (vlan 310), 10.11.70.1 (Vlan 370)
I have got new cisco ASA 5580 running 7.2(4) on it when i am trying to configured Virtual interface on vlan 400 in Gi0/0.400 to LBASE.now the problem is from my MZ zone 10.242.107.17 to Lbase virtual interface 10.242.103.1 iam not able to ping.
View 2 Replies View RelatedWe want to achieve a load balancing scenario using Virtual IP on DMZ interface on a Cisco ASA 5520.
The IPs we are going to use on DMZ are 10.15.1.2 and 10.15.1.3
These IPs are going to be NATted to all inside IPs.
Lets say our outside IP is X.X.X.X
This IP points to 10.15.1.2 and 10.15.1.3 with .2 being the primary and .3 being the secondary. When I hit the outside IP, it should point me to .2 and that .2 should take me to the inside IPs.
I have been working on figuring out a VPN problem on my companies ASA5510. I was accessing the device via: ASDM, SSH using Putty, and even initially with a console cable (also using Putty) using a computer in the networking closet. All 3 of these access methods worked properly for me.I believe I may have inadvertently changed something as of Friday using ASDM. I am mostly assuming this because, as of yesterday I can no longer connect to the device. I actually cannot even communicate with it (ping the interface I normally use to manage, which I could previously ping). No computer on the same subnet as me is able to ping the interface. The device is still accepting VPN connections, dishing out DHCP addresses and everything else it normally does, but I really need to be able to gain access to it again. I am thinking to reboot the device when there is some downtime, in the hopes that ASDM doesn't save to startup-config and only to running-config.
View 5 Replies View RelatedI just barely put in a Cisco 3925 on our network. I've configured gigabitethernet 0/2 to live on our management VLAN with an IP address of 10.129.0.31/16. I did a "no shut" on the interface. Everything should be ready to allow me to ping and/or SSH to that interface but I can't. It's really weird because I've done this a thousand times (at least on ASAs). I must be missing something. At any rate, the default gateway of the management VLAN is 10.129.0.1. I can ping that from the router. I can also ping that from my laptop (which lives on a completely different VLAN). But I can't ping the router from my laptop or vice versa.
Building configuration...
Current configuration : 1360 bytes
!
! Last configuration change at 19:05:13 UTC Thu Jan 10 2013
!
[Code].....
I am completely new to the Cisco ACE devices but have been asked to look at deploying them. I have read the ACE virtual partioning paper which covers the ACE module, and it mentions the following;"In an active/active high-availability design, both the primary and backup Cisco ACE modules are active simultaneously. The active virtual partitions are distributed across both modules, such that approximately half are active on the primary module and the remaining are active on the backup module."does the same resilience model work the same using the Cisco 4710 appliances? I.e. can we split virtual partions across two physical devices thereby having an active/active scenario.
View 4 Replies View RelatedI've got a 2621 configured as my main gateway to the internet - right now it's obtaining a DHCP ip from a the ISP's proprietary router set to bridged mode.
As of now, I'm unable to ping the internal interface of the router. I can ping external IP's only, even though I have DNS servers listed, i am unable to resolve host names. I'm running a few servers to which people are able to connect to my web server, among other services. I even have a crypto map setup to another 2621 across the country and can ping all internal ips on the other end... I JUST CANNOT PING THE INTERNAL INTERFACE of the router!!
I've noticed that when I ping the router during it's boot process (using linux un-interupted) I get a response in a very short window, then dies again. I'll post my config below:
[code]....
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies View RelatedI have five 877 routers connected to ADSL circuits provided by Vodafone. Each has a VPN tunnel back to a PIX.
Occasionally one of the sites will lose it's connection to the PIX.
When we check the log, we find entries like these:-
Apr 5 01:31:54.085 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to downApr 5 01:33:19.344 UTC: %CRYPTO-
[Code].....
As you can see, the physical interface (ATM0) is not being reported as changing state to down, neither is the Dialer interface.
When the router is in this state we have to SSL to the public IP address of it and manually restart the ISAKMP SA.
When the router sees the ATM interface go down and subsequently come back up, the VPN connection to the PIX also recovers.
So - in a long winded way I think I'm asking....why does the Virtual interface go down and is there anything I can do to stop it happening?
I cannot seem to ping from the outside of my 5520 firewall to an inside network. I have a single physical outside interface connected to a Layer 2 switch, with a laptop connected to it. This is on network 10.11.131.0/28. From there, I cannot ping to the inside interface (which is a sub interface on G0/0) with network 10.11.130.0/24/ For some reason, it doesnt work.
Now. I had access-lists in place, but have removed them for testing and it still doesnt work. I have set the security level of inside and outside to 100, and entered the same-security-traffic permit inter-interface command - still no joy. Below is the relevant configuration.
Inside Interface
interface GigabitEthernet0/0.96
description L3 Interface - Informational Zone
vlan 96
[Code].....
I have a Cisco ASA 5505, the problem is I am not able to ping to outside natted interface (ip: 172.88.188.123 and 124 and 125) from inside network I have looked for ASA documentation through the internet and still got nothing.
the config are:
: Saved
:
ASA Version 8.2(1)
!
[Code].....
I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies View RelatedI'm currently configuring an ASA5510.I connected a laptop (IP 192.168.96.18/255.255.255.0) to port 0/2 and tried to ping 192.168.100.2 ... impossible to ping outside interface.I resetted the config of the ASA to retest more simple. [code]
View 1 Replies View RelatedI ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies View RelatedI have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
So I have a client with an ASA 5520 running version 9.0 (was on 8.4) that I am trying to get either IPSec or SSL VPN configured on. I got everything setup and tried to connect. However, I couldn't connect to either. I fired up the real time monitoring and didn't see any syslog messages referring to a VPN build up. I also enabled SSH/Telnet on the outside interface and cannot connect to the ASA outside interface. I can ping the outside interface and can ping the internet from the ASA. I did set up a test ACL on the ASA and ran packet tracer on it and the results came back fine.
There is an IPS in the ASA as well, but I disabled the ACL for that and still am having these issues. Part of me wonders if the ISP has something set up to block inbound traffic. This should be a business class connection.
Internet ISP -> Juniper SRX 210 Ge-0/0/0
Juniper fe0/0/2 -> Cisco ASA 5505
Cisco ASA 5505 - >Inernal LAN switch.
1. Internet is connected to Juniper Ge0/0/0 via /30 IP.
2. Juniper fe0/0/2 port is configured as inet port and configured the Internal public LAN pool provided by the ISP. And this port is directly connected to Cisco ASA 5505 E0/0. Its a /28 pool IP address. This interface is configured as outside and security level set to 0.
From Juniper SRX, am able to ping public Internet IPs (8.8.8.8).
Issue:
1. From ASA am unable to ping public ip configured on Juniper G0/0/0 port.(/30)
2. From ASA no other Public internet IP is pinging.
Troubleshooting Done so far.
1, Configured icmp inspection on ASA.
2. Used the packet tracer in ASA, it shows the packet is flowing outside without a drop.
3. Allowed all services in untrust zone in bound traffic in Juniper SRX.
4. Viewed the logs when I was trying the ping 8.8.8.8 in ASA. It says "Tear down ICMP connection for faddrr **** gaddr **
We are going to impliment Spectrum (CA) in my network,i have ASA-5580-20 firewall now my spectrum server want to communicate with firewall,then only it will discover the firewall logs.Now the problem is my spectrum server is in MZ zone(10.10.10.45) security leval is 70 and my inside interface(10.20.20.101) security leval is 100.
I am unable to ping from spectrum server to firewall because of high security leval.How can i solve this problem,can i change my inside security leval to 69 then i think it will ping.
I am having a problem configuring my ASA 5505 for NAT.
View 3 Replies View RelatedI am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
I have Vista as my Host OS and using Microsoft Virtual PC, I have Installed 3 machines (XP, Win2003 and Linux)I am connected to Internet via USB data card.My guest OS are not able to see each other(ping each other).
View 14 Replies View RelatedI just tried to configure my ASA but unable to ping. My setup is as follows:
Cable Modem (DHCP from IPS)---> ASA (192.168.1.1)--->Belking Router (192.168.5.1)--->Switch (192.168.5.14)--->
ASA Version 8.2(3)
!
hostname WoodHomeASA-1
[Code].....
I have the following setup.
host PC (192.168.9.3) -----> gateway (192.168.9.2) ----- Pix E1 (192.168.9.1)/Pix E0 (81.x.x.250) ------ Internet
The 192.168.9.2 gateway is a 3560 switch connected to the PIX. I can ping out to the Internet via IP from the PIX, but not via the host PC (192.168.9.3) on the LAN. PIX and gateway configs below. Am I missing something that's preventing me pinging out to the Internet from the internal LAN?
PIX config
test-cal-pix01# sh run
: Saved
:
PIX Version 8.0(3)
!
hostname test-cal-pix01
enable password btf1YD.Vq7mE6vEA encrypted
[code]....
I am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br Interface IP-Address OK? Method Status Protocol Ethernet0/0 x.x.x.x YES CONFIG up up Ethernet0/1 x.x.x.x YES CONFIG up up Ethernet0/2 unassigned YES unset administratively down down Internal-Control0/0 127.0.1.1 YES unset up up Internal-Data0/0 unassigned YES unset up up Management0/0 192.168.1.1 YES CONFIG up up
I have setup 5505 ASA for Testing purposes. It has static route to layer 3 switch on outside interface that goes to the internet.
ciscoasa# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
[Code].....
I' d like to have some support for a very-basic PIX firewall configuration. I 'm dealing with PIX 515E. Inside hosts can ping inside interface , outside hosts outside interface and so on. Simply i cannot ping outside interface from inside hosts, Inside host-192.168.1.0
Outside - any host like google.com, or to check my isp link's dns ip. I have attached the pix configuration text file to test.
I configured a new Asa 5505 with Ios 8.44-1-k8.bin and when I installed the Asa the client's after about 1 hour were unable to ping or map drives to the Asa. I got the following error,%ASA-2-106007: Deny inbound UDP from XXXX to XXXX due to DNS Query. I added the command same-security-traffic permit intra-interface they were then able to ping the server and connect to the Internet, but still unable to map drives i could see the connections from the Pc's to the server in a show conn with was tcp port 445 with Saa? I reverted back to Ios 8.25 and everything works.
View 2 Replies View Related