I have a Cisco 5510 which has remote access VPN configured.Now I have new block of IP address, is there a way I can just change the outside interface IP so that people can remote in without doing anythng else?Or if I coulds be taught to create a new one.Or best way to approcah this issue?For example: it was 67.64.x.x now I need to change to 64.44.x.x.
View 1 RepliesRouter: ASA 5510
We have changed the ISP, so therefore new wan ip-addresses.
Internet works, and site-to-site vpn works, but I'm failing to localice why the remote access vpn won't work.
We've recently shut down an interface on one of our ASA 5510s as we no longer use that service provider. The dashboard, however, still insists on showing traffic usage on this interface. How do I change the dashboard to display a more meaningful interface?
View 7 Replies View RelatedOur ASA 5510 was configured with a public interface, a DMZ interface, and a private interface. I have a remote access VPN using AnyConnect client and LDAP authentication for Active Directory. We are changing ISP (groan!), which means all new public IP addresses. The new circuit is installed, so I have a second public interface (same security level as the first public interface, wholly different IP address range) enabled on the ASA. I hope to transition whatever I can, which means get the VPN access through either public interface. Can I just enable client access on the second public interface at the Anyconnect Connection Profiles tab in ASDM? That seems too simple. Can they share the one address pool?
View 1 Replies View RelatedI am adding a second external connection to an existing system on an ASA 5510 with ASA V8.2 and ASDM 6.4. I added the new WAN using an other interface (newwan).
The intention is to route most internet traffic over the new route/interface (newwan) but keep our existing VPNs using the former interface (outside).
I used the ASDM GUI to make the changes and most of it works.ie. The default route goes via (newwan). Outgoing VPNs of a site to site nature use the previous route via (outside) as they now have static routes to achieve this.
The only problem is that incomming Remote Access Anyconnect VPNs are not working. I set the default static route to use the new interface (newwan) and the default tunneled route to be via (outside) but this is the point is goes wrong....
I can no longer ping the outside IP address from an external location. It seems the outside interface does not send traffic back to the - outside interface (or at least that's where I think the problem lies). How do I force replies to the incomming VPN remote traffic from unknown IPs to go back out on the outside interface?
The only change I need to make to get everything working on the outside interface again is to make the Default Static route use the outside interface. Which puts all the internet traffic back on the original (outside) connection.
I have a cisco ASA 5510 that I have set up currently to access via ASDM through the Inside interface. When I VPN in using our older VPN server I can connect to it fine. I recently set up the ASA to also be a VPN server which will eventually replace the older server for our HQ. I noticed that when I'm VPN using the ASA as the VPN server, I can only ASDM to the public which I prefer not to allow. Access to the inside doesn't seem to work this way. What configurations if any would be causing this. I'm assuming it's some thing I need to adjust in the VPN configuration.
View 3 Replies View RelatedWe got the below alert when we ran the PCI scan on our VPN firewall (use it for remote access VPN).
OpenSSL SSL_OP_NETSCAPE_REUSE_CIPHER_CHANGE_BUG Ciphersuite Disabled Cipher Issue
Solution- Upgrade to OpenSSL 0.9.8j or later.
ASA 5510 running 8.2(2)
I need the ssh access on my ASA outside interface and have added
ssh ipremoved 255.255.255.255 outside access-list acl_outside extended permit tcp host ipremoved any eq 22 but this is the log i get from ASA
Oct 06 2012 16:10:04: %ASA-3-710003: TCP access denied by ACL from ipremoved/39884 to outside:ipremoved/22
Cisco Adaptive Security Appliance Software Version 8.2(5) Device Manager Version 6.4(5)
How to designate access-list for the remote access vpn users in order to let them access specific subnet or host,asa 5510 and acs is in the picture
View 9 Replies View Relatedis there any method on the asa 5510 let u see the history of the remote access vpn connection for the last week
View 6 Replies View Relatedwe have a server that has an outside IP and an inside IP. It's inside ip is 192.168.222.30/24 and it's outside IP is 199.204.50.2/29. The connection to this server from the outside is perfectly fine, but access from inside users to the NAT'd IP which is 199.204.50.2/29 is having issues, however, access to the inside IP works fine (this part makes sense)Will It be a must to set the inside DNS A record to the inside IP and not the outside IP, or can users on the inside interface access the NAT'd IP which is assigned to the server
LAN(192.168.222.0/24)<=====>InsideASAOutside<=====>(Server with NAT IP 192.168.222.30/24, it's also physicall assigned to this server).This is an ASA 5510 with 8.4.
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
I have a remote VPN with split tunnelling enabled. Currently, users connected to this VPN browses internet with his/her internet connection. Now, my requirement is that a roaming user connecting to the vpn must use our company's internet connection for his browsing purposes. How can I do this?Equipment we are using: ASA 5510
View 3 Replies View RelatedI am using two firewalls to connect two different offices. Firewall 5510 is running ASDM 6.3 and 5505 is running ASDM 6.2, Problem is that even after connecting two sites, i am unable to ping remote network from either side. I am mentioned static route as tunneled.
View 1 Replies View RelatedHow would I go about configuring RADIUS based AAA for remote access VPN users? I have an OSX RADIUS server and an ASA 5510
(I want to keep console and SSH using LOCAL, so I keep this: "aaa authentication ssh console LOCAL", right?)What does the rest of the config look like to get RADIUS based AAA for remote access VPN users?
My internal network consists of Catalyst 3750 switches segmented into different VLANs. There is a default route on the layer 3 Catalyst switch sending all unknown traffice to the inside Internet of the ASA 5510. However, I'd like to have a separate VLAN for wifi guest access and send all of that traffic through one of the DMZ interfaces on the ASA 5510. I don't think you can have separate default routes based on VLANs on the 3750 switches so my only option is to make the ip address of the DMZ port the default gateway for all hosts on the wifi guest VLAN.
The problem I have is that I have a couple servers behind the inside interface that have services available to the public Internet via a NAT address on the outside interface. I want the guests on the wifi VLAN to have the ability to access the servers on the inside interface using the public address as well, but have not been able to come up with a solution yet.
Here is my config that pertains to this setup:
interface Ethernet0/0description Outside Interfacenameif Outsidesecurity-level 0ip address 76.47.10.x 255.255.255.224 rip send version 1rip receive version 1!interface Ethernet0/1description Inside Interfacenameif Insidesecurity-level 100ip address 192.168.17.1 255.255.255.0 rip send version 1rip receive version 1!interface Ethernet0/3description Wifi Guest Accessnameif DMZ2security-level 50ip address 192.168.60.1 255.255.255.0
global (Outside) 1 interface
nat (Inside) 0 access-list nonat
nat (Inside) 1 0.0.0.0 0.0.0.0
nat (DMZ2) 1 0.0.0.0 0.0.0.0
static (Inside,Outside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
I've tried the following commands below but no dice.
same-security-traffic permit intra-interface
static (inside, inside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
how to totaly disable Admin/ASDM access on our public interface of our 5510. I don't want to change IPSec or SSL access to the outside interface. Just totaly disable access to Admin/ASDM from the outside without halting all other access.
View 3 Replies View RelatedI am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .
i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).
we have two Cisco ASA 5510 in failover configuration.We tried to change the public IP address on the Outside interface of the primary device but it didn't works. The new IP is not reachable from Internet nor pingable from device on the same LAN.The new IP address is in the same subnet of the old IP.
From the switch on which the ASA is connected and from another Cisco PIX we can see the ARP entry. In the analysis, on the old public IP address there was a VPN site-to-site and Webvpn defined.We tried also to shut/no shut the interface and reboot the device.
I needed to change the mask, not the ip address, of the outside interface of an 5510 running 8.2(3).
Immediately afterwards I could establish ASDM but could not re-establish SSH.
I tried the following:
Zeroize the rsa key and generate a new one Create a new SecureCRT session to accept the new key
That didn't work. All I have is ASDM access.
I have successfully setup the AnyConnect VPN (connecting to our ASA5510) and have split tunneling configured. My remote users can access inside LAN servers as well as the Internet from their remote location. What I would like to know is is it possible to change the split tunnel and not allow access to the Internet from the remote location but force the remote client to go through the VPN and out our internal edge firewall to the Internet? Basically I need my remote clients to access the Internet but I would like for their Internet traffic to go through the VPN and out our edge firewall. This will allow the same security as if they were sitting in the office.
View 4 Replies View RelatedI have a remove access vpn configured on my ASA 5510 which works fine, VPN pool easily allocates IP to all remote used , but they have few network drivers shared on their machines & most of them are linked using the computer name rather than the IP which normally doesnt work as VPN pool doesnt provides the DNS IP to the remote clients . Is it possible to allocate DNS IP with the VPN IP ?
View 1 Replies View Related I have a problem with a Remote Access VPN on a ASA 5510 8.6.2 .I have created a IPSEC Remote Access VPN through the wizard this is pretty much a base install on the ASA without much configuration.
I can connect to the ASA via the Remote Access client and get TX just no RX therefore i cannot access any of the LAN resources. [code]
I am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br Interface IP-Address OK? Method Status Protocol Ethernet0/0 x.x.x.x YES CONFIG up up Ethernet0/1 x.x.x.x YES CONFIG up up Ethernet0/2 unassigned YES unset administratively down down Internal-Control0/0 127.0.1.1 YES unset up up Internal-Data0/0 unassigned YES unset up up Management0/0 192.168.1.1 YES CONFIG up up
I am switching a switch connecting to the ASA5550 tomorrow. My current switch is using fiber connecting to the ASA. The new one only support copper. If I switch between fiber to copper on the ASA (change media-type command on interface) will it cause a down time? I have VPN tunnel on the ASA and don't want the session to reset.
View 2 Replies View RelatedI have two routers on my internal network.
10.10.199.106 is a Cisco ASA5510.
10.10.199.108 is a Sonicwall NSA 3500
The sonicwall handles our site to site VPN tunnels. The Cisco handles our client to site VPN connections.
I have a unit that points to 10.10.199.106 (Cisco) for internet access. All other clients on the network point to 10.10.199.108 (Sonicwall) for internet access.The device in question, a Synology NAS, is using 10.10.199.68 as it's IP address.
I'm trying to hit the web interface on the NAS from a remote site across our VPN tunnel. The IP scheme on the remote end of the VPN tunnel is 192.168.72.0/24.
Going through the VPN, I can hit every object on the network that uses .108 (Sonicwalll) as it's gateway. However, I cannot hit the unit that uses .106 (Cisco) as it's gateway.
I added a route statement (using ASDM) that routes all traffic destined to 192.168.72.0/24 to the Sonicwall so it can send it back down the VPN tunnel. If I'm understanding routing correctly, this should allow responses from NAS destined for 192.168.72.0/24 to go back down the VPN tunnel.
I want to setup remote access for my Android phones and tablets using Cisco ASA 5510 . Is there any particular Android client which perform the specified functionality.
View 1 Replies View RelatedI have not really set up ASAs nor VPNs on Cisco devices before. I'm currently attempting to configure a remote access VPN between ASA devices, a 5505 and a 5510. The 5510 is meant to be the server and the 5505 is meant to be the easyvpn client. The reason I am opting for remote access as opposed to site to site is that I have many 5505s at remote sites that I will need to configure in the future, and they will be moving around a bit (I would prefer not to have to keep up with the site-to-site configs). The 5510 will not be moving. Both ASA devices are able to ping out to 8.8.8.8 as well as ping each other's public facing IP.
Neither ASA can ping the other ASA's private IP (this part makes sense), and I am unable to SSH from a client on the 5510 side to the 5505's internal (192) interface. I have pasted sterilized configs from both ASAs below.
ASA 5510 (Server)
ASA Version 8.0(4)
!
hostname ASA5510
domain-name <domain>
enable password <password> encrypted
passwd <password> encrypted
[code].....
I have an end user who uses the Anyconnect VPN client to connect to our network through an ASA5510. He has a satellite ISP provider and is experiencing latency issues. Since latency issues are inherent with satellite services and since he has no other ISP alternative, any tweaks that may boost performance/reduce latency with his connection. Typcally, he sees slow performance and also network drives being intermittently available on his Windows 7 computer. he also has an internal wireless router at his home when he connects remotely. Performance when connected through a standard cable broadband connection is fine.
View 2 Replies View RelatedI have configured a remote access VPN on my Firewall ASA5510. Everything worked fine and I can successfully connect through the VPN. The problem is I cannot ping or connect to any of my internal network resources. I tried to add a new NAT route from outside to my internal servers using the defined pool but due to a new ASA version there are many changed I see in the NAT routes
View 37 Replies View RelatedHave an ASA 5510. Setting up a new DMZ zone for wireless and it will only have Internet access. What are the steps so that users on this new DMZ subnet can VPN into the Outside interface on the same ASA?
View 4 Replies View RelatedNot really a big problem, but not knowing the answer is killing me. This is what I have:
Host 1 <-> ASA 5505 <-> VPN connection<-> ASA5510 <-> Host 2
The problem is when one of the hosts trys to reach the inside interface of the remote ASA. E.g. Host 1 trying to ping ASA5510 inside interface. Again Host 1 and 2 have the same subnet address of 10.1.1.0/24. I have configured the ASA 5505 to do the the NAT translations.
[code]...
We will be moving to a new data center in the very near future and with them our WAN IP addresses will be changing. Any best course of action for changing the IP addresses throughout the firewall configuration? Would it be possible/suggested to export the running-config, make the neccessary changes, then import the config? I am familiar with the ASA 5510 only so far as changes are required. It is not something I work with on a regular basis.
View 5 Replies View Related