What I am attempting to do is setup snmpv3 on two failover 5510's .The problem I am running into, the snmp management software rejects one of the devices as it sees it as having a duplicate engine ID since the two devices share the same config. Would like to know how this would work in an active/active setup being able to poll both devices.
View 2 RepliesWe have 2 ASA 5510's setup in an active, standby failover configuration. When the primary fails over to standby, the 3rd party cert does not failover to the standby ASA. The users then receive the CERT missing, invalid message and have to select yes, no to move on. This does not occur when the primary is not in failover mode. It is my understanding that failover fails over certs but in our case it does not apper to be working correctly.
View 1 Replies View Relatedi read that you need only one L-ASA5510-SEC-PL for setting up a Active/Standby Failover. I installed the license on the 1st ASA and tried to setup the failover via the ASDM wizard. It always fails, because the 2nd device can't have a 'base' license.So does this mean, i really need another license?
View 5 Replies View RelatedI am adding a failover asa to an a firewall that is already in production. They are both 5510's, they both have the same abount of ram, have the same code versions. Will there be any downtime while adding the secondary in?
View 2 Replies View Relatedunderstanding clear about new Cisco ASA 5515-x, 5525-x.I know that this device supports IPS which is included to this appliance without any additional modules.But can this box support IPS and content-filering (Cisco ASA CX or so..) in the same time.
The problem also in next. Can two ASA 5510 with diffrent modules (in one AIP-SSM and in other CSC-SSM) be in active/active failover design?
I just added a new 5510 failover unit to an existing 5510 and when connecting my new outside interface on an Active/Standby firewall pair, i get errors messages (red x) on each port scan (monitor & syslog) although the error message indicate all ports are good...additionally the firewalls flip between active and standby non stop. I remove the new standby unit outside interface from a shared switch and everything clears up.
View 1 Replies View RelatedI need to setup an ASA 5525 in Active/Standby failover mode. I am setting up the ASA for a company that purchased only one public IP address. The public IP address is assigned to the outside interface. My question is will failover work correctly if I don't use a secondary IP address on the failover configuration on the outside interface?
View 4 Replies View RelatedI am trying to setup an active/standby failover with 5520's running 8.4(2) and am having problems with it not dropping connections during the failover. I am using a portchannel from the switch to each ASA and using sub-interfaces off that. I'm using the command Failover mac address Port-Channel1 “mac-address on primary Port-Channel1” “mac-address on standby Port-Channel1”.The command goes through but doing a show interface port-channel1 doesn't show a change in the mac address on the secondary unit after a failover when it becomes active.
View 3 Replies View RelatedI am looking at deploying a pair of 5585X's in an active/active multiple context state. I am creating Mulitple contexts that need to be able to route to each other. I was going to deploy a type of Gateway context that has a shared interface to all of the other contexts, instead of sharing interfaces directly between the contexts, i beleive this will work as basically i am just cascadng the contexts and sharing interfaces.
The main problem i have come across, is that if i deploy active/active across two appliances using 2 failover groups i can not see a way to route between them, for example.
I have Context 1, Context 2 and Context GW A including the shared interfaces of Con1 and Con2 in failover group 1 on appliance A with the respective standbys on Appliance 2. I have Context 2, Context 4 and Context GW B including the shared interfaces of Con 3 and Con 4 in failover group 2 on appliance B with the respective standbys on Appliance 1.
I need to be able to route traffic between Context GW A and GW B so that the contexts can communicate in normal operation and in failover. I do not beleive that I can share an interface between contexts in two separate failover groups and to be honest without adding a L3 device between the appliances i am not sure if this is possible.
I have an ASA5520 in location A with an ISP connection and a matching ASA5520 in location B with a separate ISP connection. We have fiber connecting the two locations and vlans passing back and forth so I will be able to configure the failover via a vlan as well as extend the ISP's to each location via vlans. The Active/Active configuration with the multiple security contexts does not seem to be an issue but how is a redundant ISP configured in this mode?We want to have context A using the ASA in location A with ISP1 as the primary and failing over to ISP 2 in locaiton B We also want to have context B using the ASA in location B with ISP 2 as the primary and failing over to ISP1 in location A Would route tracking provide the desired result? Is there a better option?
View 1 Replies View RelatedI have 2 asa 5520 firewalls including and 1 AIP-SSM-10 module in each of them. the configuration is set using active/active failover and context mode.
Both of them run individualy the IPS module. The IPS is configured using inline mode and fail-open option. However when one of the module fails and the state is changing from up to init or anything else making the IPS to fail then failover is detected and ASA consider it as failover and bounce context to the other unit.
IPS soft is 6.0(4) and ASA soft is 8.0(3)
I have checked cisco doc and it is confusing to me. it says: "The AIP-SSM does not participate in stateful failover if stateful failover is configured on the ASA failover pair." but it really does participate. Running is not really an option because of production network impact matter..
its possible to set up active/active failover using etherchannel on 5585s?
View 1 Replies View RelatedI have two ASA 5510s running in Active/Active mode. I need to make config changes on them. How do I go about it? Do I power off the secondary ASA and make the config changes on the primary and then power on the secondary ASA ? Or this another way to do this?
View 3 Replies View RelatedI have encountered a problem in one of customer that the Active ASA 5580 is unable to sync with Standby Failover ASA. When Active is connected with FO and push the configs to it will not find the ethernet/Gig interfaces due to which the all the configuration were not applied and when the primary ASA the secondary is unable to respond.
When i attached console with the Standby ASA i have seen this error.
Number of interfaces on Active and Standby are not consistent.If the problem persists, you should disable and re-enable failover on the Standby.
For detail undestanding i am attaching the configs of primary and standby ASA. The KHI-DR-ASA-BB-01 is the standyby firewall.
I am having a curious problem with two Cisco ASA 5550. They are configured in Active/Standby failover and in routed mode.The problem is: I cannot connect via SSH to the ACTIVE unit, only to the STANDBY. If a switchover is forced the problem is still the same. because it happens both with the primary and the secondary unit.It is not a L2 or a transport problem, because I can ping or access both units via ASDM.
View 8 Replies View RelatedI have a problem with failover. On My site I have 2 Firewalls 5580. And I did this configuration on my firewall.interface GigabitEthernet3/0description LAN/STATE Failover Interfacespeed nonegotiate.
View 5 Replies View RelatedI have just finished setting up two ASA5510s in Active/Standby Staeful failover, using the Management interface for both failover and state. Everything appears to be working well.Configurations were transferred and the "sh failover" on both accurately reports their status before and after a failing the active device.I monitored the inside IP with a continuous ping (using a Windows client) and noticed that there were usually two to three ping responses lost. Is this normal?
View 1 Replies View RelatedI currently have two 5540's in an Active/Standby pair. The primary unit failed on February 12th, so the secondary ASA is now the active one. My question is this - we have made a lot of changes since February 12th and I am planning on fixing this failover issue over the weekend. Will the secondary (now active) FW sync it's config to the non-active FW, or will the failed FW sync it's out-of-date config - removing any changes that we've made in the last month or so.
View 1 Replies View RelatedI am getting ready to setup avtice/standby failover on our ASA 5520's and have run in to an issue.I currently only have one External IP address available. My Idea was to use a private/placeholder IP address for the standby external IP Address, will this cause any issues with the failover? I know I won't be able to access the secondary from the outside, but that is not an issue.
View 2 Replies View RelatedI have 2 ASA 5540s ver 8.3 in Active/Standby state.I am considering a future hypothetical situation where I might need to rename interfaces or reallocate redundant interface groups. Doing so obviously has a major impact on the current primary configuration. My goal would be to minimize or eliminate network downtime during the interface changes.
I am wondering if it is possible to force the secondary ASA from the standby to active state.Then temporarily disable failover on the primary unit.Make the interface changes on the primary unit Then reactivate failover on the primary unit Force the primary unit back to active and secondary unit to standby My new interface configuration would then sync from the primary to the secondary.
I believe this would work but must ensure that the secondary ASA can function as the active unit while the failover is disabled on the primary unit. Is there a set length of time the secondary unit can remain active without a failover peer?
see issues with operating the secondary unit in this manner while making changes to the primary unit?
I am setting up a new pair of ASA 5585's in a multi-context, active/active failover design. I cannot create management SSH connection to the contexts that are assigned to failover group 2. With all the security contexts that are assigned to failover group 1 I can SSH to the inside interface IP and login without a problem. When I try to do that to the group 2 contexts there is no response from the firewall at all, PuTTY just times out.
My firewalls are running version 8.2(4). The contexts seem to be functioning normally in all other respects.
I have two ASA in failover with Active/standby configuration. When I switch from standby to active from the standby ASA I get a lot (like 100) of error messages like these below: [code] The failover works fine and nothing seems to be wrong with the firewalls function.
-Hardware is ASA5585-SSP-10.
-Software version: ASA 8.2(5),
ASA is in multiple mode with 17 active context. Why these error messages appear and what they mean?
Currently l have two ASA 5520's in a active/passive failover scenario. Currently the interfaces for the inside and outside are fixed at 100/FULL.I want to repatch them into GigE ports setup as Auto Negotiate.Is there anyway of keeping the connections through the firewall active in this type of scenrio or will l have downtime disconnecting and repatching? or could l possibly disable failover and reconfigure each ?
View 6 Replies View RelatedWe configuring ASA 8.4.2 in Active/Standby failover mode with two cables. What would be the best design configuring etherchannel on ASAs or have one active and one standby redundant cable ?
View 1 Replies View RelatedI am a single ASA-5510 with CSC module.I want to pair it for active/standby mode for failover .... can it be done if second ASA doesn't have the module? Can I assume the in case of a failover, the traffic won't be checked, and primary does in case CSC module fails?
View 2 Replies View RelatedOur customer has purchased 2 x L-ASA-AC-E-5520= Anyconnect Essentials VPN Licenses (750 Users)Ive installed both activated licenses as per the cisco guides, I didnt get any errors on the install. I did a reload on both, they are both back up and running as active/standby but when I do a sh ver the license still shows "ASA 5520 VPN Plus License"Am I being dumb and has this worked successfully or should it not now display Anyconnect when I do a sh ver?
View 8 Replies View RelatedI have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies View RelatedI'm trying to setup SNMPv3 on a Nexus 5548. We are using SNMPv3 on 3750's without any issue, but haveing issues getting it setup on the Nexus.I have been using the following link for the setup following it line by line. [URL]The part that I'm having issues with is when I try to enforce SNMP message encryption on a per user basis. When I issue snmp-server user (username) enforcePriv, I get warning: unable to update CLI users database. reason: role does not exist grounp not found.
View 1 Replies View RelatedConfigured ASA 5510 ISP failover and working fine.My ASA as configured as DHCP server also. So its serves IP addressing details including mask,default-gateway, DNS server IPs.Here my issue is whenever my ISP failover occurs my ASA sends previous ISP DNS server IPs to my inside clients.
Here i like to configure my ASA to serve IP addresses dynamically.Or is there any global DNS IP addresses which will work for all ISPs?
If the 5510's support active/active ha. There is conflicting info. on the datasheet stating otherwise.
[URL]. As business needs grow, customers can install a Security Plus license, upgrading two of the Cisco ASA 5510 Adaptive Security Appliance interfaces to Gigabit Ethernet and enabling integration into switched network environments through VLAN support. This upgrade license maximizes business continuity by enabling Active/Active and Active/Standby high-availability services.
Can I run Cisco ASA failover with dual ISP run active/standby configuration and SLA monitor to monitor the primary ISP gateway and failover to the secondary gateway but not failover to the failover firewall unless an actual event occurred that required a ASA failover?
View 3 Replies View RelatedI have two ASA 5510's that I want to setup in a Active/Standby configuration. My only question is on how to connect the inside ports to my LAN. I have 5 Catalyst 3750's stacked together that connect to the ASA's. Should I run the inside interface on ASA1 to a port on switch 1. Then run the inside interface on ASA2 to a port on switch2? And make sure both those ports are in the same VLAN? But, then when failover occured, how to I automatically make it clear the arp cache so the traffic starts flowing out of the right port?
View 1 Replies View RelatedI have a customer with two ASA 5510s. All four ports are used by the following interfaces: inside, outside, dmz, and failover. This customer is looking at getting redundant internet connections, but we don't have any ports to the redundant connection. What I'd like to know is it possible to configure sub interfaces on one of the currently occupied ports (I'm thinking inside) and use one for inside and one for failover. This way I could have the other port free for the redundant internet connection.
View 1 Replies View Related