Cisco Firewall :: ASA-3-106001 - Inbound TCP Connection Denied From Flags SYN
Jun 24, 2012
I have 2 cisco routers that resired on the same interface on Cisco ASA. For security reasons, on both of the routers I have configured default gateway to be ASA interface, then static route between them on the ASA, I get the following error when on station comming from first router trying to connect to another station behind secound router (again, on the same interface, maybe this is the issue?).
ASA-3-106001: Inbound TCP connection denied from flags SYN
There is access list allowing traffic between but hit count is 0
View 4 Replies
ADVERTISEMENT
Oct 6, 2011
I configured an ASA 5505 a couple of weeks ago. Every thing is working properly except it sends irritating messages to the syslog server. Her is an example of the message:
%ASA-2-106001: Inbound TCP connection denied from 195.215.221.56/80 to 10.70.13.90/252 flags PSH ACK on interface outside
%ASA-2-106001: Inbound TCP connection denied from 195.215.221.56/80 to 10.70.13.90/2252 flags ACK on interface outside.
View 1 Replies
View Related
May 2, 2012
I have an issue were thousands of connections on the ASA are marked with flags E, below is a visual of the connection. Any ideas what could cause this marking? Also, I can't grasp what the meaing of an outside back connection (ie flags E).
TCP DMZ:X.X.X.X/139 Inside:X.X.X.X/1828, flags E, idle 9h37m, uptime 9h37m, timeout 15s, bytes 0
View 0 Replies
View Related
May 14, 2012
I have ASA 5510 with 8.2.4 and 8.0.x OS and all seem to have common problem of idle TCP connections not timing out. The host to host connections are coming over VPN tunnels. I have default timeouts on all the firewalls. I have tried changing global timeouts and as well as host specific timeouts using MPF but doesn't work at all ! The problem is when TCP connections are sitting idle in conn table for days and when connection limit of 50,000 conns reach the firewall starts behaving unpredictably dropping packets or unresponsive! I need the unused idle connections to timeout which is NOT happening either by changing global values or MPF.
View 1 Replies
View Related
Sep 16, 2012
I have a slew of 106001 messages coming into ASA log, from the outside interface. it appears like most of them are for standard traffic, such as TCP 80/443. i suspect these messages are from clients on the inside who have initiated connections to the internet, but then the client abruptly terminates application of something similar. Server side finally issues a close connection, reset or something else. Here is an example, with the ASA address being 1.1.1.195 (changed to protect the innocent ).
Another theory is that the NAT ip for clients is different than the actual interface IP, so that is behaving differently. For example, once the xlate times out, the IP used for the xlate is no longer active and any return packets to the interface would also error out - be refused. If the xlate was using the interface IP, that it would always respond in some way?
I can bump 106001 down to notification (5) or informational (6) level.
View 5 Replies
View Related
Apr 25, 2012
Trying a simple Easy VPN connection and getting the following in the error logs:
Built inbound UDP connection 684 for outside:xx.xx.xx.xx/1106 (xx.xx.xx.xx/1106) to identity:xx.xx.xx.xx/500 (xx.xx.xx.xx/500)
View 1 Replies
View Related
Jul 26, 2011
I've just taken over a new network with a Cisco ASA5520. Everything is working fine, except I am being bombarded with 106001 alerts from a few internal hosts to one specific internal host. The description in general is "Inbound TCP connection denied from 10.1.0.1 to 10.1.0.5 - both of those are valid internal hosts and the TCP ports are also valid. I tried looking at the log and getting it me to tell me which rule was causing these alerts, but it just came back with 'It's not possible for these type of alerts'
- How is it possible for the ASA to even pick up on this when, in theory, the source host wouldn't be going near the ASA since it's on the same subnet?
- What might be causing this?
- How can I turn it off!! (I guess that'd be fixed by point 2)
View 4 Replies
View Related
Oct 18, 2012
I would like to understand someting about the behaviour of ASA with our traffic scenario and the management of tcp sessions.
1) In particular we noticed that we have connections with the flags Fin without any acknowledgement. The session is silent (the bytes counters aren't incremented) but it remains in the session table as an established connection with the idle timeout of an established conn.
We have about 20% (60K on 300K total) of conns in this state: at our eyes it seems to be an incorrect behaviour...
TCP OUTSIDE 62.149.128.151:110 INSIDE 10.254.158.12:61527, idle 0:11:36, bytes 433, flags UFIO
TCP OUTSIDE 17.151.0.200:443 INSIDE 10.254.229.94:52367, idle 0:01:25, bytes 4597, flags UfIO
TCP OUTSIDE 184.169.79.33:443 INSIDE 10.255.249.146:60143, idle 0:10:39, bytes 5590, flags UFIO
TCP OUTSIDE 157.55.235.158:80 INSIDE 10.170.37.102:62421, idle 0:00:53, bytes 1770, flags UfIO
2) On the connections considered as half -closed we have received an ack to the fin (r or R flag is present), we would like to set the idle timeout to a value lower than 5 minutes but we were not able to reach that result
timeout pat-xlate 0:00:30
timeout conn 0:10:00 half-closed 0:05:00 udp 0:02:00 icmp 0:00:02
!
access-list timeoutClass extended permit tcp any any eq www
access-list timeoutClass extended permit tcp any any eq 8080
class-map timeoutClass
match access-list timeoutClass
class timeoutClass
3) And this type of conns with a Fin on both side that I'm not able to understand... with an ack on one of the side how can I have the other fin??
TCP OUTSIDE 69.171.247.38:443 INSIDE 10.168.139.244:51236, idle 0:11:28, bytes 10536, flags UfFIO
TCP OUTSIDE 69.171.247.38:443 INSIDE 10.168.139.244:51234, idle 0:12:22, bytes 9070, flags UfFIO
TCP OUTSIDE 88.40.119.73:36962 INSIDE 10.255.93.162:36875, idle 0:13:27, bytes 3562, flags UfFIO
View 3 Replies
View Related
Nov 3, 2011
I have a client that has an ASA 5520 that has two internet connections, FIOS and Comcast. The ASA is configured to failover from the FIOS to the Comcast if the FIOS fails. This works perfectly fine. However, I was wondering if VPN and other inbound traffic will come into the secondary connection when it is active. I think VPN will work inbound when the FIOS connection fails, but I am not sure about the other inbound connections.
View 1 Replies
View Related
Jul 12, 2012
I know this issue probably has been beat to death, but I have yet to find the answer to my situation. We recently upgraded from a PIX515e to ASA5520. Shortly after the install I noticed a problem with the servers on our DMZ. This problem was NOT present with our old 515e. The problem is that there seems to be a communication problem between servers on the DMZ, specifically when I try to open the web server homepage from my mail server, I get time-outs. When I ping between the two in either direction, I get time-outs. This might seem trivial, but I have other data servers on the DMZ that need to communicate between themselves.
When we question the tech that performed the install, his answer was that there might be a problem with the switch the servers are connected to, or the servers might have a virus. He stated the process of ping should never involve the DMZ interface. And yes, our DMZ interface IP is the gateway for the servers. Now, if the DMZ (ASA) should never come into play with a ping, why when I turned on logging did I receive the error below? It sounds to me that the ping is going through the interface. Here are a few of the errors on the DMZ with the specific server IPs.
july 13 2012 12:50:04 106014 10.10.0.10 10.10.0.5 Deny inbound icmp src dmz1 10.10.0.10 dst dmz1 10.10.0.5 type 8, code 0
The ping problem was only used as an example the demonstrate that there is a comm problem on the DMZ. ASA is running in router mode.
View 5 Replies
View Related
Jul 29, 2012
I am currently configuring a Cisco 881 router and am having some vpn connection issues:I can connect with one user (me) and all other connection attempts form other users are denied. When I disconnect, other users can connect - the scenario is that only one user can connect at any given time.
Here is my config:
Building configuration...
Current configuration : 11423 bytes
!
! Last configuration change at 13:11:23 PCTime Fri Jul 27 2012 by zephyr1
! NVRAM config last updated at 13:25:30 PCTime Fri Jul 27 2012 by zephyr1
!
version 15.0
[code]....
View 1 Replies
View Related
Jan 1, 2012
I consider the NAT mechanism to be quite straight forward, but although the firewall ACLs allow the traffic, it is being denied. The ASDM log and packet-tracer indicate the problem being an ACL.
# the internal resource
object network mabe-mbp
host 10.0.0.36
!
# these are ALL of the rules on the outside/inside interfaces
access-list outside_access_in extended permit tcp host 1.2.3.90 any eq 12380 log disabled
access-list outside_access_out extended permit ip any any log
access-list inside_access_in extended permit ip any any log
access-list inside_access_out extended permit ip any any log (code)
View 2 Replies
View Related
Jan 14, 2013
I'm having problem getting ICMP echo monitoring on outside interface to work. I've set: icmp permit host monitoring_station_adress outside but I still get:
%ASA-3-313001: Denied ICMP type=8, code=0 from monitoring_station_adress on interface outside. I'm trying to directly monitor ip on ASAs interface outside.
I have access-group tied to "in" direction on interface outside. Do I still have to put "permit icmp" rules despite the fact that icmp permit outside command is set?
View 4 Replies
View Related
Feb 19, 2012
I have a website that is hosted by our company, but when the staff goes to the outside address of th website it gets denied by ACL thus page not found.
3Feb 20 201211:25:23192.168.3.5752928our Extrenal IP80TCP access denied by ACL from 192.168.3.57/52928 to inside: our External IP/80,OUr external ip is also the ip of the 5505.
View 1 Replies
View Related
May 6, 2012
I have ASA5505 configured with internal network as 192.168.15.0 and default gateway 192.168.15.1 From the inside network, i'm able to access internet and able to ping all website (enabled ping). and all internel network devices can ping each other. Except i cannot ping my gateway (ASA5505) 192.168.15.1. I'm continously seeing this message on the log, when i tried to ping.. How to fix this?
Denied ICMP type=8, code=0 from 192.168.15.xxx on interface inside
replace xxx with my network devices that try to ping the gateway..I dont want outsiders ping my gateway, i need ping for inside internal network only.
View 5 Replies
View Related
May 28, 2013
I am attempting to allow traffic from one vlan to another.Vlan 1 is on Interface 0/2.vlan1Vlan 2 is on int 0/3.vlan2Each vlan can communicate inside it's own vlan, and the gateway on each responds to vlan specific clients My problem is that I am unable to communicate between the two vlans. Using the ASDM packet tracer tool, I find that packets are denied by the default rule (on the second Access List lookup). It appears as if the packet never reaches the other interface. The access rules are set up to allow traffic from one vlan to another (inbound), on both interfaces. Testing from either vlan to connect to the other fails. Below are the accee-rules for each vlans. Once I get basic connectivity working.
access-list aVlan1; 3 elements; name hash: 0xadecbc34
access-list aVlan1 line 1 extended permit ip any 192.168.151.64 255.255.255.192 (hitcnt=0) 0xeb0a6bb8
access-list aVlan1 line 2 extended permit ip any 192.168.151.128 255.255.255.128 (hitcnt=0) 0x3a7dfade
access-list aVlan1 line 3 extended permit ip any 192.168.151.0 255.255.255.0 (hitcnt=0) 0x93302455
access-list aVlan2_access_in; 3 elements; name hash: 0x6dc9adc7
access-list aVlan2_access_in line 1 extended permit ip 192.168.151.64 255.255.255.192 192.168.150.0 255.255.255.240 (hitcnt=0) 0x054508b7
access-list aVlan2_access_in line 2 extended permit ip 192.168.151.128 255.255.255.128 192.168.150.0 255.255.255.240 (hitcnt=0) 0xc125c41e
access-list aVlan2_access_in line 3 extended permit ip host 192.168.151.3 192.168.150.0 255.255.255.240 (hitcnt=0) 0x4adc114c
View 19 Replies
View Related
Apr 28, 2011
Connection denied due to NAT reverse path failure
View 2 Replies
View Related
Mar 16, 2013
I am trying to troubleshoot a problem where in one of my remote site is not able to access some networks at HQ over Site to SIte VPN ( asa 5505 at Remote and 5520 at HQ). I ran packet tracer and HQ ASA looks clean as everything came out as ALLOW. Remote site ASA packet tracer give me DROP out at Phase 9 (VPN). I am not very sure what to look in ASA for resolution now. Is it an access list that is blocking the traffice or VPN setup.
View 5 Replies
View Related
Apr 9, 2012
I have a customer with a Cisco ASA 5510 firewall, an inside network containing a Genetec video recording server, and cameras installed on broadband modems throughout the area (each with a public IP). They've recently purchased Axis Q6034-E cameras that use H.264 to stream back to the video recording server. The camera has a view mode where you can watch it through H.264 or Motion JPEG. The view with M-JPEG works, but when I switch to H.264 the video stream is denied. We have allowed RTSP, RTP, and HTTP (it's setup with only http, not 443)traffic from the camera address on the cable company public network but are still being denied the video stream. The recording software requires that the feed come from the H.264 feed, so the motion jpeg does not fix the underlying issue of being able to record.
We know it's the firewall because if we install the camera on the inside network, the video feed in H.264 works to the recorder.
How to enable something special on the firewall to allow traffic through from the device?
View 1 Replies
View Related
Jul 4, 2012
I am trying to lock down the VPN access on my Cisco 5520 ASA's whereby I wish not to allow users to SSH access etc on servers running on the same interface that they are VPNing into.
I did not originally configure the ASA and so I am slightly confused by some config on it. Currently when I attempt to PING a server within the same interface as the VPN network I get the following error in the logs below.
5 Jul 05 2012 09:45:15 305013 monitoringsystem Asymmetric NAT rules matched for forward and reverse flows; Connection for icmp src dmzAHdata:VPN IP dst AHdata:monitoringsystem (type 8, code 0) denied due to NAT reverse path failure
As a workaround I created a NAT exempt rule which then allowed traffic to the server in question however I wish to limit the traffic to only ICMP and when I do this in the firewall it does not take affect. Is this because of the NAT exempt rule?
View 1 Replies
View Related
Aug 6, 2012
I am trying to setup an inbound NAT on an ASA5510 running 8.4 code.
object network obj-192.168.1.2
host 192.168.1.2 (internal web server)
object network NAT-external IP
host ** external IP **
object network NAT-external IP
nat (outside,inside) static 192.168.1.2 service tcp https https
access-list outside_access_in extended permit tcp any host 10.2.0.10 eq https
This seems to be setup now?
sh nat
2 (outside) to (inside) source static NAT-*.*.*.* 192.168.1.2 service tcp https https
translate_hits = 0, untranslate_hits = 0
sh access-l
access-list outside_access_in line 2 extended permit tcp any host 192.168.1.2 eq https (hitcnt=27) 0x59383a04
When I try to connect to the external IP using https I get hits on the access list, however the nat translate hits do not go up?Do I need to allow the 192.168.1.2 server back out again?
View 1 Replies
View Related
Dec 29, 2011
I am trying to configure my ASA5505 to allow SMTP relay and the ACLStatic I created is not working.
View 1 Replies
View Related
Oct 30, 2012
I have setup an ASA5505 running 8.2 with dual ISP's
Primary link is the current live static route out and the backup picks up if the primary fails. That all works great However I have an issue with inbound NAT rules
I have configured an inbound static on the primary which works great
static (inside,primary) *.*.*.* 10.1.1.1 netmask 255.255.255.255 access-list outside_access_in line 2 extended permit tcp any host *.*.*.* eq 3389 (hitcnt=4)
Question? With the primary link active and the default route pointing out through the primary, am I able to configure an inbound NAT to the same inside host 10.1.1.1
on the backup link?
If the primary fails users will need to be able to connect inbound to this service
When I try to set it up I got this error ERROR: Static PAT using the interface requires the use of the 'interface' keyword instead of the interface IP address
So I tried that and got this error WARNING: All traffic destined to the IP address of the backup interface is being redirected. WARNING: Users will not be able to access any service enabled on the backup interface.
So what is the best practice for configuring inbound NAT for a dual ISP configured ASA
View 1 Replies
View Related
Apr 20, 2013
I have a 2621 router - old. but works well.Need to put in an ACL to limit the inbound SMTP traffic to be FROM a specific set of IP's, and deny all others.
I have tried various combinations with no luck. Something obvious, I am sure.
When I do a show access lists 160 it shows all SMTP traffic being snagged by the SMTP deny statement. All other traffic works correctly.
Here is my config so far...
Current configuration : 3093 bytes!version 12.2no service single-slot-reload-enableservice timestamps debug uptimeservice timestamps log uptimeno service password-encryption!hostname xxxxxxxxxx!logging rate-limit console 10 except errorsenable secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx!ip subnet-
[Code] ....
View 6 Replies
View Related
Jan 30, 2012
I know I can use the RTR statement to determine when the primary ISP circuit goes down via this technote: url...My question can I assign static Nats on the backup ISP connection to the same inside servers in the dmz.?Example 10.1.1.11 is mapped to ISP1 ExternaIP of 65.217.77.11. Can it 10.1.1.11 also be mapped to ISP2's 208.217.77.11?This way I can get my DNS changed and my inbound traffic to servers in my DMZ on the asa 5510 running 8.0.3 code can continue to receive Inbound traffic.
View 1 Replies
View Related
Jun 1, 2011
I have ASA 5510 and public FTP server from my local network to external IP address, with static nat translation. All works, but I need request to ftp come from internal ASA interface (need use gateway different ASA). How configured ASA for forwarding request?
View 4 Replies
View Related
Feb 26, 2012
I have been asked to create an inbound connection on the ASA from the internet to a part of the network that is accessible over the Wide area network eg
-Internet address 94.175.x.100 goes to 151.5.3.100,
-The internal network is 10.42.15.0/22, and connects to the 151.5.3.0/24 network over a private MPLS.
Is this possible with the ASA5510 and if so can you give me a clue how to pass the traffic
View 6 Replies
View Related
Nov 7, 2012
I have an ASA5510 with 8.3 and a Cisco PIX525 (retiring). The ASA was for VPN traffic only while the PIX was for all other Internet traffic. I'm trying to move all the traffic to the ASA5510 so I used the PIX to ASA migration tool. I migrated the PIX rules over to the ASA5510, however we can't receive email and there is no external access to our internal websites. But the VPN connections remain intact and internal users can get out to the internet.
When I run Packet Tracer on my outside (incoming rules) the packets are dropped at the inside interface. What am I missing?
View 1 Replies
View Related
Dec 18, 2011
I have successfully been able to allow outbound access from inbound hosts on the appliance; however, I have only one outbound IP address and had to configure outbound access using static PAT. What I need to do is to configure access to certain inbound hosts from outside. What's wrong with my running config? Below are the commands that I believe need to be changed from the configuration. [code]
View 14 Replies
View Related
May 31, 2011
Last night I switched out our old Cisco pix 515 with a asa 5505. The config is the same and internet and outgoing mail is working but no mail is coming in. Below is a copy of my config. Why my inbound mail is not coming in.
smtp 192.168.51.248 (Barracuda email filter)pop3 192.168.50.11 (exchange server). Tried to telnet into the firewall but connection timed out. Went to mxtool box and that also timed out while trying to connect to smtp. Port scan from mxtool box timed out too on all ports.
[Code] ........
View 5 Replies
View Related
May 12, 2011
how to set up port forwarding for inbound SSH?
The outside interface on the ASA is on DHCP. I have a single dynamic public IP from my ISP. The inside interface provides Internet access for the network using NAT.
I have a server on the internal network with an IP of 192.168.0.6 and I would like to access this via SSH (TCP port 22) from outside.
I've been able to do this in the past on a PIX with a static public IP block, but I'm new to ASA and I don't know how to do it with PAT.
Current running config attached for what it's worth, but it's pretty basic at the moment.
View 3 Replies
View Related
Nov 20, 2011
I'm running a Cisco ASA 5510 with version 7.2(3) and I've been tasked with permitting some inbound & outbound TCP & UDP ports to/from a specified address space on the internet.
In looking at my current ASA config I see other access lists already configured so I'm assuming I can just set up a new access list in similar fashion, but I wanted to verify here first.
View 6 Replies
View Related
Oct 9, 2011
So I recently purchased an E4200 to replace my aging and slightly ailing DLink DIR-655 which as served me well for going on 5 years. The part of the DLink that was giving me the issues was the wireless, the routing and switching worked fine however.
I do quite a lot of streaming of media from my home machine outside my network through the internet. Most recently I've been using Kalemsoft Media Streamer on my HP Touchpad, however I've used Zumocast, Windows Live, Splashtop, and a few others. I havent yet tried my PPTP VPN through the router for an extended period of time to see if it reflects this issue as well though.
Since replacing my 655 with the E4200 I've started experiencing a timeout issue. It seems to be semi-consistant and only happens after time of unuse or extended use (I havent timed it yet to see if it always happens after the same amount of time though).
Basically what occurs is this:
I'll be watching some video or listening to audio streaming from my machine and after a period of time (usually a long period of time) it'll suddenly lose connection, requiring me to re-connect through the software, like the NAT translation is timing out or something.
How it USED to work is this: It'd basically work until I stopped streaming.
My setup:
AT&T Uverse set to DMZPlus aiming towards my E4200 WAN port (sitting directly in place of the 655 I used to have)
All machines on the network are gigabit. I have ports 7000 and 7001 open for Kalemsoft Media Streamer on the E4200 per the specifications of the software.
The software understands UPnP so I have nothing specific forwarded on my machine, but I didnt previously either.
View 4 Replies
View Related
