I just replaced a PIX 501 with a new ASA5505. I had a very weird problem and would like to know what caused it incase I run into it again. The setup is a DSL connection, with an old-ish speedstream DSL modem. Static IP, no PPPoE. I had a PIX 501, then two servers with static NAT entries on secondary WAN IPs. Everything was working fine on the PIX, I just duplicated the config over to the ASA. I swapped out the PIX for the ASA, and rebooted the DSL modem to clear out it's cache. After installation, NAT was working fine for the the global pool, but the systems with static NAT could not get online. I tried lots of different things to fix them, and they never worked. Finally I rememberd running into an issue like this a long time ago, in that the static NAT IP's wouldn't work without giving them a bump-start on the network. So I assigned the ASA each of my WAN IPs, one at a time, and tested them all. After that I went back to the original WAN IP, configured the static NATs, and they fired right up. why did my static NAT entries not work until I first assigned them to the ASA, then swapped back? I did reset the DSL modem when I swapped the firewalls, so I don't believe it was an ARP issue (unless it was an ARP issue at the far end?) I would like to know if there is something I can do differently with the devices or with the config to not have this issue again in the future.
Currently a customer has all theLAN devices using a router as the Default Gateway. The router also do the Dynamic NAT to the internet access and has NAT/PAT rules to publish some services like HTTP and FTP. As I know the router will permit all the incoming traffic in all its interfaces without restrictions at less there is an ACLs that restrict the incoming traffic on an specific interface.Now the customer has bought a brand new ASA and wants to use it as the default gateway for the entiery LAN. This means, the ASA will have the internet connection and will be the responsible for the NAT/PAT process.
I have configured the NAT/PAT rules already following the current router configuration, but I need to know if I have to configure ACLs allowing the incoming traffic on th Outside interface for the services I NATed.
I have a Cisco ASA5505 running 8.2(1) and I am using ASDM to manage the firewall. I have a Linux VPN server on the inside with and IP address of YYY.YYY.YYY.39 with a static NAT to the outside with an address of XXX.XXX.XXX.171 . I have a site to site VPN tunnel which terminates on the outside of the ASA on the outside interface XXX.XXX.XXX.190 .Traffic from the YYY.YYY.YYY.0/24 network can't transverse the site to site VPN as there is a conflict of IP address's on the far side so it is natted via a dynamic policy to host address ZZZ.ZZZ.ZZZ.100, Users remote into the inside(YYY.YYY.YYY.0/24) for support via the Linux VPN server (.39) and then need to communicate down the site to site VPN. The problem is that the static NAT for the incomming connections takes preference and bypasses the site to site VPN tunnel for outbound traffic. I tried to create a policy Static nat but it tries to modify the static nat that handels the incomming traffic to the Linux server.
i have 2 internal server sitting in inside interface
inside network vlan 1 ip address 192.168.0.20, and 192.168.0.22
i going to map 192.168.0.20 to public ip routable address 203.117.124.180 and 192.168.0.22 to public ip routable address 203.117.124.181
the purpose is to make those 2 server 192.168.0.20, and .22 to be able to access remotely using public routable ip address,
however, after done the configuration i still not able to ping or access the public IP Address mention above. my both server are turn on and can access internally.both server are also able to access internet. See below partial configuration retrieve from Show Run.
I have a 5505 for a small business that has one web server. The web server has a static NAT entry to an IP address and not an interface. There is an access rule allowing any HTTP traffic to the outside IP of the web server. From the web server I can't access the Internet.
All other computers on the network can access the Internet using a dynamic nat rule that uses the outside interface. The web server is accessible from a computer behind the firewall.
If I delete the static NAT entry for the web server I can get on the Internet.
I have turned debugging on and see that an outbound connection is built and then 30 seconds later the connection is torn down with the bytes 0 SYN Timeout message.
I have an ASA 5505 behind my internet router. i have got only one public ip configured on the router outside interface.192.168.20.0/24 subnet is configured between ASA and router and inside network is 192.168.10.0/24 (Refer the attached diagram).
I have exposed my mail server and ftp server to public through static PAT in router and ASA with the same public on router outside interface. Iam facing issue some of the machines inside my network internet is not working(actually DNS is not resolving) some of the PC's internet is working fine some of the PC's randomly working. i have attached the diagram and ASA config , after this issue is sorted out i need to configure a L2L VPN to my head office.
I have configured the ASA in a very similar manner to how the PIX was set up but I'm having trouble with some hosts on the inside accessing the Internet. Any inside hosts which use DHCP work fine. Any inside hosts with a static IP (and configured on the ASA with a "static" rule) cannot access the Internet. For example, in the config below the server daviker-dialler cannot access the Internet. I've spent a few days working on this now and have started from scratch several times but I'm not getting anywhere. Apologies for all the X's everywhere, didn't like to post anything sensitive on the Internet.
I am mapping static ip address to the local ip address.We have a bsnl broadband connection, and bsnl has provided us with one static ip address.We are using broadband modem.Now I would liket to map this static ip address to one of the private ip address which is 192.168.1.2(database server).i want to do nat above ips if i do so then i dont have no ip to assign to my outside interface.I would like to access this device over internet, by typing my public (Static ip ) given by the BSNL.security device i have is cisco ASA 5505.
I am setting up a Cisco ASA 5505 first time for My organisation, I usually setup Cisco Router, I have 10 Static IP, & Have 6 Server (S-1, S-2, S-3, S-4, S-5, S-6), Traffic Should be pass through the ASA and is distributed to the destination server that is specified in the packet. LAN servers can be separated into discrete networks for security. For example, a private LAN for internal traffic accessed only via remote dial-in VPN sessions and Want to Configure DMZ for Server (S-4, S-5, S-6) that allows public web traffic.
I have Attached My Network Diagram I have some question,
1:- Can we Configure Multiple Static IP On ASA 5505 ?
2:- If Diagram is wrong what change need to be done ?
I have ASA 5505 with basic licence, v9.1, ASDM 7.1. I want to create the DMZ for a web server.
The interface 0 is for the outside network The interface 6 is for the DMZ All other interfaces are for the inside network
My ISP provided me with one public static IP address, one gateway address and a subnet mask 255.255.255.252
1/ I would like to ask which interface I should assign the public static IP address to. Should it be assigned to the outside interface 0, or should it be assigned to the DMZ interface 6, while outside interface would be configured to use DHCP?
I tried to assign the static IP address to the outside interface first, but then when I used ASDM the “Public Servers” feature to configure NAT, I get error message that the outside interface and the public address cannot have the same IP address.
2/ For the sake of peace of mind, I am thinking about using the second firewall, which would be used only for the inside network. Can I connect this second firewall to one of the inside interfaces of the 1st firewall,
I have created a simple static ip address by using this command:
interface Vlan1 nameif inside security-level 100
[Code].....
But, no matter what, the I can't ping the static address or access the computer 10.2.1.2 from outside of the asa 5505. I have attempted to ping from inside of the asa 5505 or from another computer. I just does not work.
I also have created several rules that allows icmp traffic.
icmp unreachable rate-limit 1 burst-size 1 icmp permit any echo-reply inside icmp permit 10.2.1.0 255.255.255.0 inside icmp permit any echo-reply outside icmp permit any outside
I just upgraded my firewall to ASA 5505. Now, my original static ip address cofiguration is gone. Apperantly, Cisco went away from static ip address to something like nat (inside,outside) dynamic interface. how to create a static ip address under version 8.4? By the way, I am sharing what my configuration used to look before upgrading.
I was checking out the config on my ASA and noticed a bunch of static routes configured when I did a show route. With the exception of two that I expect to be there, the remainder point traffic destined for specific internal hosts to the outside interface, i.e.
S private_ip 255.255.255.255 [1/0] via public_ip, outside
I verified that I cannot ping those hosts from the firewall. I logged in to the ASDM. When I check the Configuration>Device Setup>Routing>Static Routes it only shows two static routes, the ones I expect to see. If I look under Monitoring>Routing>Routes, I see the same output as I did on the CLI. I looked around to see if I was missing a key location for this information, and I was able to see the same static routes output in Monitoring>Routing>Routes. Since this is under monitoring though there's no way to delete these routes, and I still don't know where they were configured originally. Then I happened to check under Monitoring>VPN>VPN Statistics>Sessions, and I see several of the private IPs used in the static routes being used by VPN users, including my own! I know I didn't assign myself a static IP for VPN use or anything like that. So, what are these static IP routes? Why do I see them in the CLI and not under the Configuration tab? I mean, I know I can delete them from the CLI but I'm trying to figure out why the info is not synced. Am I seeing dynamically created content based on the VPN connections?
Now I would like to start using the clientless VPN feature of the ASA, so I of course don't want that particular port forwarded to the server. Is there a way to define such an exclusion? I've tried several things, including setting up a separate NAT rule to direct that port back to the ASA's interface, without luck.
If that is not possible, what configuration would I need to move to in order to get the behavior that I want? It is important that all (non-VPN) traffic is passed exactly as it arrives at the firewall (whether it is coming from internal or external), with the exception of changing the IP address (i.e., I need static port mappings for some of my services).
I am having difficulty following the logic of the port-translation. Here is the configuration on a 5505 with 8.3,So I would have thought the outside access-list should reference the 'mapped' port but even with 3398 open I cannot remote desktop to the host. If I open 3389 then I can connect successfully.
I've having a problem with our company ASA5505 router.
We recently moved to a new adress, so everything had to be set up again. I have a static IP, submask and gateway from our new ISP. The router have been factory reset before moving. We have betweeen 10-20 employees on our LAN in the office. In an attempt to make things easier I have changed the internal IP (and IP range) to 10.0.200.1 with a range from 10.0.200.5 - 10.0.200.100 as our NAS/printer/plotter have IPs within this range.
I can ping machines on the internal IPs and in ASDM the Outside interface is show as "up" with a green arrow. But there still isn't any internet connection. The only thing I haven't tried (because people need the current network to be online) is changing "route inside 0.0.0.0 0.0.0.0 62.242.X.X 1" to "route outside 0.0.0.0 0.0.0.0 62.242.X.X 1"
I have recieved a primary and secondary DNS adress as well, but I'm in doubt as to were I'm supposed to enter these (Using ASDM Version 6.3). I would like everything "Behind" the router to be run by DHCP.
Here is the running config: ASA Version 8.2(2) ! hostname ciscoasa
Trying to connect a 5505 with a dynamic address on 8.3(2) to a static IP'd asa (5510 on 8.2(1) with a DefaultL2LGroup and dynamic maps already created.
Inside networks: Local (5505) 192.168.100.0 /24 Remote (5510) 10.100.1.0 /24
Each FW have a LAN behind it. The D-Link and the unknown device are both working perfectly and clients on each subnet can connect to the internet?However when I connect the ASA 5505 to the 2960 SW with a configued static route: Route Outside 0.0.0.0 0.0.0.0 x.x.202.1 1 is says it has no route to host?
If I connect the ASA5505 to the LAN of D-Link DSR-1000N and give it a static address and a static route match the D-Link LAN network, it works perfectly, however not when I connect it the the Cisco 2960 Switch
I'm having some issues configuring NAT statements on my ASA5505 which has recently been upgraded to 8.41.
I have a single dynamic IP on the outside interface of the ASA and would like all internal hosts to NAT/PAT to it. In addition, I would like to have several ports 'forwarded' to internal hosts, one of which is TCP/4343. With the current configuration all hosts are NATing to the external interface properly but the service running on TCP/4343 is not accessible from the outside. See command output below:
"sh run object" output: object network DrJones host 10.81.220.90object network LAN-10.81.220.0 subnet 10.81.220.0 255.255.255.0 "sh run nat" output: object network DrJones nat (inside,outside) static interface service tcp 4343 4343object network LAN-10.81.220.0 nat (inside,outside) dynamic interface "sh run access-list" output: access-list inside_access_in extended permit ip 10.81.220.0 255.255.255.0 anyaccess-list outside_access_in extended permit icmp any any echo-replyaccess-list outside_access_in extended permit tcp any interface outside eq 4343
We have two sites: 192.168.100.x and 192.168.101.x currently connected via IPsec VPN. On each end we have a Cisco ASA 5505. However, each site also has an MPLS VPN with intentions to move all traffic to this link. Will this work on the ASA? We need to make sure traffic can hit the ASA @ site A on the inside interface and trafiic will forward to the MPLS VPN router which then handles the traffic. Too, will it cause any problems in bi-directional flow between the two sites?
I wanted to move to the cisco arena, and having a bugger of a time figuring out simple nat/pat rules combined with access lists. I've been reading Richard Deal's Cisco ASA configuration book, googling the heck out of this simple problem and can't see what I'm missing.
I have an ASA 5505 unlimited security plus license running 8.2(3) and a simple network, 192.168.0.x internal, 192.168.3.x dmz (not even touching that yet!) and outside I have a /29 subnet of addresses, 25 is the gateway, and 26-30 are my addresses.
I have simple dynamic nat set up on the .26 address to nat to 192.168.0.x. All I'm trying to do is port forward a simple tcp port I set for my linux server (192.168.0.2) on the inside, for arguement's sake, it's 2222 (it's not really). My outside vlan 50 is X.X.X.226 255.255.255.248 , can I make a static nat (inside,outside) x.x.x.226 192.168.0.2 netmask 255.255.255.255 ?
I tried using (inside,outside) x.x.x.230 192.168.0.2 netmask 255.255.255.255 and that didn't work either. Is it not possible to use two external addresses to hit the entire /24 range AND a single server?
My access rule for this nat is permit tcp any 192.168.0.2 eq 2222 (where I'm using 2222 for my ssh port). then I apply that access list to the access group interface "outside".
I thought the outside interface would do a proxy arp (since I do not have the sysopt noproxyarp command) for my 227,228,229, and 230 addresses where .226 is my internal nat for all my internal machines i.e. 192.168.0.1 -> x.x.x.226 . I had this working like a charm before with my fortinet, so I know I have systems listening.
I'm working on setting up a template configuration for the Cisco ASA 5505 device that we'll use to configure more routers for various client needs. One of the requirements requested of me is the following: Internal hosts assigned a DHCP address are blocked from the internet Internal hosts with a static IP are permitted access to internet All internal hosts can communicate regardless of state
Now, I'm fairly new to this and I'm certain my terminology isn't correct so googling the problem has been fruitless. I have followed basic configuration guides and have configured the device to hand out DHCP addresses to hosts plugged in ports 1-7. If I'm plugged in and specify my address manually in the OS I am blocked from any access so I can only assume there is an access policy or some rule preventing me from authenticating against the router despite having set up VLAN1 to be the entire class C subnet. What sort of steps would I need to do to configure this? New access lists. For the record, the dhcp addresses are in the range of 10.100.31.64-10.100.31.95. VPN users are assigned an address from 10.100.31.220-10.100.31.240 and there seems to be no issues with that configuraiton. I don't wish to constrain what addresses a user can use should they specify a static IP (10.100.31.5 should be just as valid as 10.100.31.100).
There is a PIX firewall and it has this configured on it.static (inside,outside) tcp interface 3389 192.168.1.250 3389 netmask 255.255.255.255 0 0.This line of code works ok for port 3389 but I want all tcp ports to be translated. Not just 3389.
I have an ASA5505 running which is on a static IP. I have just got an SRP527W for a remote worker and want to create a site-to-site VPN into the ASA. I have a number of other router of non-cisco brand which just all dial-in and connect no problem.
On other routers I have been abloe to specify the DDNS hostname in the VPN setup so that the ASA can identify it. I'm not sure how I setup the SRP527 to connect to the ASA.
I am using a Cisco ASA 5505 Here is a description of my topology.
Headquarters = 192.168.201.0 Client X = 172.16.0.0 Datacenter = 10.12.0.0 Site to Site Tunnels: Headquarters ---> Datacenter Datacenter ---> Client X
I want to ability for computers in the Headquarters subnet to access the Client X subnet.I have tried setting up a static route to push all traffic destin for 172.16.0.0 to the datacenter, but was unsuccessful. how I can route all 172.16.0.0 through the tunnel.I have tried ading a static route on my ASA but without success.
Based on the network object below, I am looking for confirmation that It is good practice to use this natted object in my ACL applied incoming to the inside interface rather than have another object specifically for the object My_PC. I have tested and it does work, however this is my preffered option rather than having to create 2 objects, for the host and also the natted host.ASA(config)# object network My_PCASA(config-network-object)# host 192.168.33.2ASA(config-network-object)# nat (inside,outside) static 209.165.201.2
The order in the older ios was nat 0 then static. With the new ios how is the static nat treated if i have a nat (inside,outside) source static Now I need to do some static one to one nats for some servers in the same subnet as the no nat
its basic configuration where i have my server on the inside network (172.16.0.7) which i want it to be natted to public ip to (195.44.148.53) .
i tried to add an access-list ingress direction on the outside interface to permit traffic from any to the public ip 195.44.148.53 but still its not working.
I have some sites already connected with ASA 5505 site to site VPN with both end static IP. Normally, all traffic can come across without any problem. Even I used "management-access inside" for both ASA.Now I have a new office with only ADSL pppoe connection. I used easy VPN to connect from Site B:remote dynamic IP site to SiteA:static IP with similar example of this: [URL]
All my 5505 ASA are running 8.4(4)1 Site A - Static IP Site B - dynamic IP with pppoe connection.
After EasyVPN connected, i do not know how do I remote manangment from site A lan to site B 5505 ASA?
