We have an ASA 5505 running version 8.4. We are having problems allowing external traffic to access computers behind the firewall. Our current config is:
I have a Cisco 5505, 2 sites that are internal, 1 external IP (dhcp from cable modem). While on my laptop, ipad, iphone, I cannot access the server via it's external IP address. I MUST use the internal IP in order to access this site. I have heard of hairpinning, internal dns server(don't really want this).
I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
I'm usually not working with this product, but this is what I'm trying to do.I have 2 internal networks setup on our Cisco ASA 5505 firewall. (not done by me, I'm a new to this product)I'm trying to access a server on one network from a PC located on the other internal network. (preferable through the web gui)When I try "Packet Tracer" from interface "Trust4" it fails on the NAT phase.(Source ip: 10.0.4.99, Destination ip: 10.0.6.99) When I check the NAT rule, it says: Type Source Interface AddressDynamic any outside outside.
I am aware that we can allow external admins to telnet over a custom port to the internal router. Even i was allowed to connect to a remote router via the remote firewall. The way i was accessing the router is by telnet to the remote ASA address on port 8023.I am not sure how exactly we can configure this on a ASA.
I have an ASA 5505 with the base license,When I setup the DMZ interface I had to add the deny access to the inside VLAN. The DMZ works fine with WiFi on it, but user's iPhones can't get email unless they turn WiFi off.Is there a simple way to allow HTTPS traffic through the DMZ interface to our internal Exchange server which is NAT'd on the 5505's external IP?
I have configure Cisco 5505 as layer 2 firewall mode. I have vendor machine connected to Cisco ASA 5505 on port 2 as VLAN2 inside then VLAN1 outside connected to my internal network on layer 2 cisco 2960 switch. This machine needs access only to LOGMEIN then block all internal/internet traffic.
vendor machine on vlan 2 inside >> Cisco ASA 5505 vlan1 outside >> layer2 switch >> internal LAN >> Cisco 5520 main FW >>> INTERNET
I have a cable modem internet connection and my cable modem is connected to an ASA 5505. The inside interface of the ASA has an IP address of 192.168.2.2 and is connected to a Linksys router's internet port which has an IP address of 192.168.2.1. The Linksys router then has a local area network of 192.168.1.0 and all my clients are on that network. Everything is working fine except in my ASA logs all the traffic shows up as the router's external address which is 192.168.2.1. I would like to see the 192.168.1.x address of the clients in the ASA firewall. I've tried making some changes to the Linksys router but that hasn't resolved it. Is there any changes I can make on the ASA to get this to work?
I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
I am having some trouble accessing some backup Email (Outlook Web Access) and Citrix servers located behind an ASA 5505 firewall at a remote datacentre. Simply put, when I go to the specific URL (e.g. [URL]) I do not arrive at the splash page, I just get a message saying that the server took too long to respond in the web browser. I'm wondering whether I have missed something on the configuration or the firewall itself is not letting my requests through. The remote servers are located at a remote Disaster Recovery site and use the subnet 192.168.4.0/24. I am at head office which is connected to the DR site via a VPN using 192.168.1.0/24.
The first one I use to provide internet access to my office. The other two I'm going to use for the following: I'm going to deploy a server in internal network which must have 2 external ips on his network interface (& one internal ip on the second,but that's ok: I cannot put an extra network switch before asa & plug this server there: this server is virtual & is on esxi host in internal network. External ips must be assigned to servers' interfacw,bot just forwarded there (ms direct access requirement).
I tried the solution posted at [URL] however it did not work on my ASA5505 8.4(2). I thought that it may be because I only have a single public address so the web server is responding to port forwarding through the one public IP already. looking in ASDM it appears to indicate that a configured access list is blocking the server from responding to the internal hosts.
Can I fix an access list (or something) to make this work or am I wishing for too much with only one public IP? This worked by default on my Netgear firewall.
I have a 5505 between a vendor router & my company network, vendor is not able to access devices on internal network. I am also not able to access the firewall via asdm
I have a issue that i am at a loss as how to solve it. I have an ASA 5505 as my firewall. I have users from other companies who visit from time to time and are unable to use their outlook email to send messages. They can however receive messages without a problem. I also have a situation where users who use windows live to access gmail are unable to send messages.
I have narrowed it down to the fact that these uses are using ssl/tls to send the mails. I did some research and found out about the inspect esmtp setting in the ASA. I have disabled it and i still have to problem. I have also removed all outbound deny statements and still no luck.
Of note is that i can send emails without attachments. They take a long time to go out ( from minutes to hours) but eventually they do. Emails with attachments of even 10k do not go at all.
I was running image 8.2.3 and i downgraded to 8.0.5...still did not work...i upgraded to 8.4.3...still did not work. I am now back at 8.2.3.
My Firewall config is attached. I am at my wits end as to what else to try. The company has not renewed support for the device so i am on my own here!
I'm configuring a 5505 for a remote office. Until they are assigned a static ip by the provider I will have to use the providers dhcp address. How do I construct an access list for the outside interface using the external address if I don't know it yet? is there a commnd that will insert the ip address in to the access list once one is assigned?
I have a ASA 5505, which has two IPSec RA tunnels build, for each one the user is able to authenticate and get an IP address is the designated IP pool, but they are not able to ping the Firewall, or RDP to any internal servers. Here is a copy of the running config:
: Saved : ASA Version 7.2(2) ! hostname ciscoasa(code)
Our secondary site accesses the internal intranet via a link, which is basically:
[URL] where externalip is the IP address of my router.
* This used to work fine before we migrated from ADSL (6mb up / 0.5mb down) to Fibre(70mb / 20mb) *
Internally, I access the same link, but via [URL] Internally it loads in 2 seconds, externally it is taking 68seconds(ish)..
I can't work it out, the fibre shouldave made things loads quicker but is infact very slow. I'm wondering if something network wise is going on.
The intranet is a php intranet sitting on apache, and using postgresql as the database. Other pages load fine, this specific index.php page does quite a lot of DB connections and so on, but as I say before, it worked fine before the migration.
We have Cisco ASA 5505, 90.x.y.2/29 IP is assigned to outside interface. We have one internal HTTP server so that I use static (inside,outside) tcp interface [URL] to forward all incoming HTTP traffic to internal HTTP server 1. Now we need to add new physical HTTP server 2 so that I would like to forward
HTTP traffic to e.g. 90.x.y.3/29 to 172.16.0.11.
How can I do that? See scenario image (scenario.png) if needed.
I have Astaro UTM running on an old computer as my only firewall right now. The Astaro also serves as my DHCP server. My Wifi is provided by a Linksys E3000 running DD-WRT software. NAT/SPI are disabled on the E3000, and it forwards DHCP requests to the Astaro. All my network clients connect via wifi/ethernet to the E3000.
All clients --> E3000 (no firewall) --> Astaro --> www
I am considering setting up my own personal cloud server using a Synology NAS that I can access remotely. I would also like to remotely access my Surveillance DVR. I would like to access them via VPN or portforwarding. I do not want to use DMZ.
I would like to utilize the SPI firewall on the E3000 to provide an extra layer of defense. I would like the NAS and the DVR to be on an external LAN between the Astaro and the E3000...and all other clients being on an internal LAN behind the E3000. I have the necessary switches/cables to make this work.
My question is...How do I configure the E3000? Can I have both the internal and external LANs on the same subnet? Do I have to use the NAT on the E3000? I'd rather not...since that will render the Astaro's reporting functions rather worthless.
I would like the Astaro to remain the only DHCP server. I would like all internal LAN clients to be able to reach out to the external LAN/WAN...but the external LAN should not be able to reach into the Internal.
I was just wondering if it's possible with an ASA 5510 to connect to the external IP address of an internal server from inside the network. I have already set up dns doctoring for dns lookups, and everything is working fine there. We have an application inside the network that tries to connect straight to the external Ip of another internal server. where to look in the ASDM 6.4?
I recently cut over from a WRT54G to a RV120W. I am having an issue where I type [URL] (for a server running on my network) in my web browser while on the internal network and it always comes back with the router login page. Basically it is supposed to go out of the router and then come back in on the public IP address and hit that server. There was a function on the WRT54G called "Filter Internet NAT redirection" which when turned off would allow this to happen. I am not seeing a feature like this on the RV120W
I am using a 6500 with FWSM. I need to separate an internal server/HQ network from 3 or 4 different external connections. The external networks do not necessarily need to be isolated from each other.I have the option of using a 3 layer model: L2 Access layer to SVIs on the Distribution layer and then L3 to the 6500.L2 Access, connecting directly to the 6500s, with the SVIs on the FWSM.Is it better to have the FWSM outside the MSFC or Inside? Am i correct in thinking that "inside" vs "outside" is determined by whether the SVI's are configured on the FWSM or the MSFC? is there any performance impact from having the FWSM doing the routing instead of the MSFC.If the vlans are all configured on the FWSM, what is the 6500 doing, other than providing switch ports?
I am working on replacing our Checkpoint Firewalls with ASA's, and am running into the following NAT problem. On some of our Checkpoints, there are external NAT's that are mapped to multiple internal hosts based on ports.Is there any way to translate that to the ASA? I'm not sure the ASA will let you have multiple internal hosts mapped to one external IP using static NATs. The main issue, is these are alarm panels that receive data from external hosts (the traffic is initiated externally on the Internet) so I can't use dynamic PAT with this.
i have reviewed this configuration a couple of times and I am not seeing my error. I have two internal subnets, in different VLANs with the ASA being the default router. The internal zone works fine, but the zone called wireless on VLAN 13 doesn't. The firewall blocks all communications and the rules look correct to me. I want all traffic on this wireless subnet to be allowed to cross over the firewall and NAT to the outside interface, just as the inside zone does.
I have created a new sub-interface on our ASA 5520 for guest internet access.
My goal is to allow access to a few specific services hanging off some dmz interfaces on the same firewall and full unrestricted access to the internet only. Everything else should be out of bounds.
The order of the rules I plan to setup on the guest interface inbound are:
#1. <rules to allow access to specific services in the dmz>
#2. <block any ip access to the entire private network ip address space>
#3. <permit ip any any>
#1. These rules will give access to the guest user to services located in the dmz
#2. This rule will block all access to any services in the private ip address space (thus blocking access to all internal services)
#3. This rule is to allow access to any other services i.e. the internet.
Is this the best way to achieve my goal in the most secure way or is there a better way? i.e. is there a way to force the traffic by default to only go out the outside interface unless there is a specific rule allowing it go elsewhere?
(Of course Dynamic PAT will also be configured for traffic coming from the guest interface to the outside interface.)
I have a cisco ASA5505, it runs a wide site to site VPN network and has 4 servers connected to it
10.50.15.4 > fileserver 10.50.15.5 > domain controller (exchange) 10.50.15.6 > terminal server 10.50.15.7 > terminal server
Now yesterday i removed 10.50.15.6 and replaced it with a new terminal server with the same ip address, ever since the ASA is blocking traffic between it and the domain controller (example)
2Oct 27 201214:51:0510600710.50.15.655978DNSDeny inbound UDP from 10.50.15.6/55978 to 10.50.15.5/53 due to DNS Query What has me baffled is the only thing different between today and yesterday is the new server is windows server 2008 and the old one was windows server 2003. The new server has the same LAN ip address as the old one to make the changeover seamless for the users.
why all the sudden my ASA has decided to block the traffic between those machines? all the other machines can talk to it fine just not the domain controller, and seeing that this is a terminal server naturally you can see the problem i face!
this router has worked flawlessly for 2 years now without any config changes and i cant work out why its blocking traffic between those 2 machines.
We have a new Cisco ASA 5550 that I am trying to configure. We are currently using a borderware firewall.
We have multiple external IP addresses and I can NAT traffic from all except for our external interface IP address.
When watching the packets in the ADSM monitor if the IP address is our external IP then I see nothing unless it is ICMP. I can ping the IP address just cannot do anything else with it.
All the rest of our provided IP addresses can be NATed and work correctly.
Traffic for our external interface IP does show up when we use the borderware firewall so we know the traffic is getting here.
we have a Cisco 2901 as a router on a stick for several vlans. Everything on the segment routes fine and accesses the internet just as they should. The 2901 connects to an ASA5505 on port 0/1. Any host connected to the ASA5505 can access the internet, but can not ping into any of the vlans off of the 2901. The strange thing is on either segement of the network I can ping all of the gateways. What is even more strange is when I run wireshark from behind the firewall going into the 2901 I can not see the packet on another wireshark instance behind the 2901. However if I start a ping for a host host behind the asa I can see the packet in wireshark on the host, which I am trying to ping, hit the gateway.
I am new to the ASA series and I am at a complete loss as to why I cannot configure this router to forward SMTP and RDP traffic to an internal host.
The packet trace tool in ASDM shows complete end-to-end connectivity for RDP but it still fails to connect from outside. This is my config file, what I need to change in order to make it work?
I am using ASA5510 and i want to know if it is possible to redirect http traffic to an internal proxy software. I explain : PC from the LAN use a internal proxy in their IE browser but some other PC doesn't use it.They are directy connected to the Internet using the Public IP from the WAN interface ( via NAT). Can we redirected this HTTP Traffic from the WAN interface to the Proxy in the LAN ?
Http Traffic will be routed like that : PC -> WAN interface -> Proxy -> WAN interface -> Internet In fact,can we create a rule saying : All http traffic which doesn"t come from the IP Proxy must be redirected toward proxy.
