Cisco Firewall :: ASA 5505 Creating Interface Vlan In Firewall
May 3, 2011
I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
View 4 Replies
ADVERTISEMENT
Oct 26, 2012
I have ASA 5505 with base license. I created 3rd vlan on it.it was created. but i am unable to assign IP to it. i assign ip address it takes it. But when i do sh int ip brief it does not show any ip.
Code...
View 7 Replies
View Related
Jun 8, 2011
I've got an ASA 5505 running 6.3 I've connected the management interface to our management vlan (which contains switch IPs, ilo's etc)Is there a way to allow access to this vlan from another?
View 1 Replies
View Related
Mar 7, 2012
Our external security department needs to scan, every three months, a computer behind the firewall. I need to create a simple NAT rule that will allow an ip address or subnet to the computers behind the ASA 5505. At the moment, we have a simple NAT rule which allow all network traffic to exit from inside to outside.
View 19 Replies
View Related
Mar 22, 2012
I have created a simple static ip address by using this command:
interface Vlan1
nameif inside
security-level 100
[Code].....
But, no matter what, the I can't ping the static address or access the computer 10.2.1.2 from outside of the asa 5505. I have attempted to ping from inside of the asa 5505 or from another computer. I just does not work.
I also have created several rules that allows icmp traffic.
icmp unreachable rate-limit 1 burst-size 1
icmp permit any echo-reply inside
icmp permit 10.2.1.0 255.255.255.0 inside
icmp permit any echo-reply outside
icmp permit any outside
View 1 Replies
View Related
Feb 19, 2012
I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies
View Related
Mar 23, 2013
May I know the reason why we cannot create interface vlan on Cisco ASA 5510?
View 2 Replies
View Related
Jan 13, 2013
Whether it is possible to have same vlan on multiple interface on ASA 5510 and higher models ?
View 2 Replies
View Related
Jan 29, 2012
Is it possible for me to create 2 vlan interfaces on the 6500 and have them both in the same subnet?
For a specific customer requirement I would like to have a vlan interface on the 6500 as default gateway, sat in it's own vrf, and then route all traffic inbound and outbound to this vlan through the FWSM interface, preferably in the same subnet. I don't think this will be possible so just looking for confirmation either way.
As I will be running EIGRP between a pair of central 6500's and 2 remote offices it will make things much easier for me advertise the connected FWSM interfaces in to EIGRP for access in/out of all my VRF'd subnets. If I need another subnet for each VRF FWSM next hop then I'll have to reditribute a list of statics which I don't really want to do.
The reason I am not just using the FWSM as gateway is because I need to run HSRP across 3 different devices (another 6500 in a second suite), and failover FWSM will only give me 1 level of redundancy for those gateways.
View 3 Replies
View Related
Dec 10, 2012
I want to creat sub int on ASA 5505 but when I am trying below command it show error.
------------------------------------
config t
int f0/0.3400
------------------------------------
My ASA software version is 8.2(5).
View 5 Replies
View Related
May 13, 2009
Can we make sub interface on Cisco ASA 5505 model and if its possible then do that interface need to be upgraded into Trunk Port.
View 8 Replies
View Related
Jan 30, 2012
On our ASA 5505 We have a DMZ configured to use 2 ports, which are used by the mail and Web servers. So far everything works perfectly and this router has been very stable. Now I need to add more ports in order to accomodate prototype Web servers in the DMZ, but no more ports available on the Cisco. Looking through the ASDM though I noticed the DMZ seems to be configured as "VLAN 5", sure enough with VLAN ID 5. So I tried creating a VLAN with ID 5 in my ProCurve switch, isolated from other VLANs. My theory being that plugging on of the the router's DMZ interfaced onto this VLAN would allow me to add my test servers. Well, this seems to work, but for only a very short time. I can get the landing page from my test server to display, and then everything slows down to a crawl and communication seems to be blocked. Out of curiosity, I tried to put my prod server and email server on the VLAN, together and separately, but the same thing happens. At first, I can ping the machines, then after a few request, everything stops responding.
View 1 Replies
View Related
Aug 15, 2011
I have a Cisco ASA 5505 that I have configured. The outside interface is vlan 2 and the inside interface is vlan 1. Port 0 of the ASA is configured to be in vlan 2 and is connected to the ISP provided subnet. Port 1 is connected to my private LAN subnet. I have an additional router connected to Port 2 for guest connectivity. Port 2 is configured to be a member of VLAN 2 so that it can access the ISP provided subnet. From the device connected to port 2 I can ping the vlan 2 interface address of the ASA and from the ASA I can ping the Default gateway of the ISP provided subnet. For some reason the router on port 2 cannot ping the default gateway of the ISP provided subnet. If the vlan were working the same as a vlan in a switch, I would expect to be able to do this. why it is not working or what I can do to get it working?
View 4 Replies
View Related
Mar 14, 2013
I have IOS 8.0(4) and the base 50 User License...will this config work? I have two networks; my home network, and my lab. I want to split my Internet connection between them, but keep the networks separate for the most part. Will my license allow this config since I can't do DMZ?
interface Ethernet0/0
switchport access vlan 3
!
interface Ethernet0/1
switchport access vlan 1
!
interface Ethernet0/2
switchport access vlan 2
[code]....
View 1 Replies
View Related
Sep 9, 2011
I setup a site-to-site VPN tunnel at the remote ASA5505. I am able to asdm to the outside interface but not ssh. I switch to telnet and still not allow me to access. I added an ACL to allow telnet any to the outside interface but still not working. In ASDM I see the log Here is the second issue. When I want to change the telnet back to ssh using ASDM I got the following error.
View 2 Replies
View Related
Aug 13, 2011
I have a problem where my outside interface stops passing traffic and the only way to resolve the issue is to reload the ASA, the interface never is down it just stops passing traffic. The inside interface never stops allowing traffic to pass as I can get to all my internal servers and shared drives.
The firmware is:
asa821-k8.bin
Running Config
: Saved:ASA Version 8.2(1) !hostname f1domain-name somedomain.co.ukenable password w1Y.GBKFyC5NqO3M encryptedpasswd 2KFQnbNIdI.2KYOU
[Code].....
View 4 Replies
View Related
Nov 6, 2011
I'm using asa 5505 with 8.4(2) and have the following problem.I have 2 Networks. each Network has it's own externel Internet-Ip and also Mail-Server.
[code]
Now I want a communication between the two Mailservers with their external Ip-Address.I did a static NAT from ipnt any to int any or also from int routed to int routed, but nothing worked.Packet tracer showed at NAT-Lookup where the externel adress of the second Mailserver is passed: Info Static translate Network1 to Network1
But it should show a translation from network1 to network1-external.Due to Security reasons, I cannot paste the whole config.Under 8.0 I did the same configuration with Policy-Nat and it worked.
View 1 Replies
View Related
Nov 21, 2011
I have setup ASA 5505 with 2 ISP, named outside (primary) and backup, the scenario is if outside down, then backup will take over, it works now. But it is not working when the primary connection cannot reach the gateway with the interface still up.
Is it possible when the primary connection cannot reach the gateway then backup automatically take over?
My configuration is:
ASA Version 8.2(1)
!
hostname cisco
[Code].....
View 4 Replies
View Related
Nov 14, 2011
I have a Cisco ASA 5505, the problem is I am not able to ping to outside natted interface (ip: 172.88.188.123 and 124 and 125) from inside network I have looked for ASA documentation through the internet and still got nothing.
the config are:
: Saved
:
ASA Version 8.2(1)
!
[Code].....
View 2 Replies
View Related
Jul 17, 2012
I am working on ASA 5505 with Base License that uses 3 VLAN's.
-My VLAN 1 is for used for my home network.
-VLAN 2 is connected to the public Internet and my IP gets assigned by ISP dynamically.
-VLAN 3 is DMZ where I will have few VM's that would need access to and from the Internet.
I am looking to work with following:
1) 172.16.0.2 that sits on DMZ will need to access public Internet over port 80
2) Permit access from the Internet over port 3389 to 172.16.0.2
3) Permit any host on private VLAN (192.168.0.0 network) to access 172.16.0.2 over the port 3389
4) Permit second VM on the DMZ VLAN let say 172.16.0.3 to access public Internet on all ports. Access in to this host is not permitted.
5) For some reason DHCP hosts are NOT getting DNS (8.8.8.8) entry when IP hets assigned or renew. I have a statements below but it is not working.
Also, if ACL rules for VoIP are written correctly. The goal is to permit these ports (SIP related) to access VoIP router. [code]
View 1 Replies
View Related
May 26, 2013
Site A:
ASA5520
VLAN data subnet 172.16.10.x/24
VLAN Voice subnet 10.0.0.x/24
Site B:
ASA5505 Base license
VLAN data subnet 192.168.10.x/24
VLAN Voice (restr) subnet 10.0.1.0/24
The callmanager is located on site A and needs to sent out DHCP-offers to site B through the VPN so the IP-phones can register to the callmanager. I got the VPN up and running for the data-subnet but i can't get traffic through the voice-subnet/VLAN.
Can the ASA's do the job or do I need to route traffic before the ASA's on both sides and sent it through the tunnel, configured both subnets as interesting traffic? Ofcourse the last situation I need to upgrade the license for the 5505 to gain more VLAN's.
View 4 Replies
View Related
Jul 8, 2012
Ive been readin all over the internet (including this site) trying to figure out if the asa can handle intervlan routing. Im not sure what I am missing on my config to get this to work. Ive read that it can work and Ive read that it cant work. How to get this to work on my asa 5505.
Here is my setup
Cable Modem ---> ASA (eth0/0)
(eth0/2) -->unmanaged switch for LAN connectivity
(eth0/3) --> Access point for wireless LAN connectivty
My config is attached
What I would like to do is be able to communicate between vlan3(LAN) and vlan4(Wireless LAN)
Whats strange is I can RDP between the two vlans but I cant ping or anything else.
View 20 Replies
View Related
Sep 2, 2012
ASA 5505, I got a security plus license which allows multiple VLANs.I want to be able to configure the ASA to allow only RDP session (One way) to another Switch where all the VLANs are. I've attached a pic of what I want but I'm struggling.
I looked at documentation saying you should have inside and outside interface but I'm not sure on this scenario.I've configured inside interface on ASA e0/1 and interface VLANs but not sure what to do between ASA and Switch?
View 2 Replies
View Related
Feb 12, 2013
This is for an ASA 5505 with the base license...I have a situation where I will not have one interface in my outside VLAN, but instead I want to have interfaces 1-7 in my outside VLAN and interface0/0 in my inside VLAN.
Is this supported with the Base license, and if so how would I do this? Do I still just need to assign one IP address to the outside VLAN?
Or will I need to upgrade to the Security Plus license and put each interface in a separate outside VLAN, so in essence I would have 7 outside VLANs each with the same security level (0)?
My situation is that I have several partner networks that i want to "aggregate" thru my one ASA 5505. So each outside interface represents a separate partner (outside) network, each of which I want to get to from my inside network. Hence the many outside to one inside.
View 5 Replies
View Related
May 10, 2011
I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies
View Related
Apr 23, 2012
I am connecting the inside interface to an upstream switch and therefore will need to assign a static IP address to the inside address as I did below:
#sho int ip brief
Vlan1 123.123.123.123 YES manual up up
I will also use this to manage the ASA. I am having a problem with the network configuration of the inside interface as I can't ping the gateway and/or the in IP of the inside interface.Do I need to add any routes?
View 3 Replies
View Related
May 2, 2013
I was asked to block pings from the internet to the outside interface of our ASA-5505 firewall. I found a post that said to enter "icmp deny any outside", however that does not do it.
I created an ACL to try and do the trick, also to no avail:
access-list outside_in extended permit icmp any any echo-reply
access-list outside_in in interface outside
access-group outside_in in interface outside
View 8 Replies
View Related
Dec 14, 2011
I am trying to configure two ASA-5505 as a failover pair. Software 8.2.5 and ASDM 6.4.5.206 Using the wizard i get to step3 .. then nothing happens. Trying direct in asdm but the only interface i can choose is "--None Unnamed-"
View 1 Replies
View Related
Dec 12, 2011
I have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
View 4 Replies
View Related
May 30, 2011
I enabled snmp config ASA 5505 with Version 7.2(4), the NMS/reporting system can give graphs for CPU & Memory usages. But I can't see any elements about physical interfaces.
View 1 Replies
View Related
May 25, 2011
I would like to allow users from network 10.132.23.0/24, 10.132.33.0/24, 10.132.24.0/24 access to our SQL server(192.168.1.7) located on the inside interface(192.168.1.0/24 network) Those networks (10.132.0.0/16) come from the DMZ interface.
View 12 Replies
View Related
May 17, 2013
How can i enable Netflow for each Vlan Or interface indvidually in Cisco ASA? currently i have setup Netflow and only 2 interfaces are shwoing traffic for Netflow which are not even as my physical or Vlan interfaces . (see screen shot )
EscapeASA# sh interface ip brief
Interface IP-Address OK? Method Status Protocol
Internal-Data0/0 unassigned YES unset up up
[Code].....
View 9 Replies
View Related
Aug 7, 2012
We need to have one connection with less internet bandwidth assigned to it than all other other connections. Basically it is a separate conection from all others, incoming just from one switch port and separate VLAN.I know this can be done on the switch by limiting the bandwidth allocated to a port,
however, is it possible to have the speed limited down, just before it goes to the internet, ie, on the ASA, rather than doing it on the switch?The firewall is an ASA 5505.
View 2 Replies
View Related