Cisco Firewall :: ASA 5505 Ping Inside To Outside Don't Go

Sep 29, 2012

I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
 
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
 
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
 
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254

View 2 Replies


ADVERTISEMENT

Cisco Firewall :: New ASA 5505 / Can't Ping Inside Interface

May 10, 2011

I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?

View 1 Replies View Related

Cisco Firewall :: 5505 - Can't Ping ASA Inside Interface

Dec 12, 2011

I have an ASA 5505 that I'm trying to set up a guest network on.  I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it.  The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
 
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
 
[code]....

View 4 Replies View Related

Cisco Firewall :: ASA 5505 / Cannot Access Internet Or Ping From Inside Interface?

Jul 26, 2011

I am having a problem configuring my ASA 5505 for NAT.

View 3 Replies View Related

Cisco Firewall :: ASA5510 - Unable To Ping From User Desktop To Firewall Inside IP

Jun 11, 2012

I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to  FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
 
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:

[Code].....

View 7 Replies View Related

Cisco Firewall :: ASA5505 Can't Ping New Firewall On Inside Interface

Jul 14, 2011

I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.

View 32 Replies View Related

Cisco Firewall :: Cannot Ping To Inside Hosts From ASA-8.2

Jun 8, 2013

I am struggling to get successfull pings beween asa and inside hosts but couldn't succeed. Done packet tracer result is acl-drop
 
Here is the running config
 
Prem-ASA(config)# sh run
: Saved
:

[Code].....

View 7 Replies View Related

Cisco Firewall :: ASA5510 Cannot PING From Inside To Outside

Jul 1, 2012

I cannot seem to determine exacly why I am not able to ping from the inside to outside using the standard 100/0 security levels respectively. I am dynamic natting the inside to the outside interface, something I don't usually do but cannot see why ICMP's are not passing through.
 
The Packet trace tool says there is something in the ACL but there really isn't.
 
Is there simply an issue of Natting to the WAN interface on a 5510?

View 10 Replies View Related

Cisco Firewall :: ASA5505 - Can't Ping Inside Host

Sep 29, 2012

I just try to ping a internal Host but it want to go.
 
Laptop<===>ASA5505
 
Connected is the Laptop at Ethernet 0/2 Inside
 
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
 
But If I try to ping to the Laptop I get the followed:
 
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
 
From the Laptop to the ASA5505 I can Ping successfully.

View 6 Replies View Related

Cisco Firewall :: ASA5510 - Cannot Ping Inside Over VPN After Upgrade

Jan 16, 2012

We currently have a central hub using an ASA5510 and then a few site-to-site VPN connections to our support staff homes. The devices at the homes are Cisco routers. We were running version 8.25 on the ASA and all was working fine. We recently upgraded to version 8.42 and although all the functionality of the network is ok and it does what it should, our support staff cannot ping, ASDM or telnet to the ASA inside interface anymore whereas they could before the upgrade. The home VPNs all run on a 10.30 subnet (i.e. 10.30.1.x, 10.30.2.x etc etc). I can post our config (security edited of course), but it is quite a big config. The command management-access inside is specified and the 10.30.0.0/16 subnet is permitted to ASDM and Telnet. Are there any extra things that have to be done in version 8.42 to get this to work as the support staff do have to access the firewall for configuration purposes. At the moment, they have to telnet to one of the routers on the local LAN and then Telnet to the firewall from there.Prior to the upgrade, they were all able to ping the inside ASA interface and also telnet and HTTPS to it from their PCs at home. Now they cannot and the only change made was an upgrade to 8.42. Immediately after the upgrade none of them can ping the interface anymore and it seems it can only be accessed from the local LAN. I cannot find any access-lists that might be blocking the packets so can only assume it's something in the way 8.42 works.

View 8 Replies View Related

Cisco Firewall :: PIX 515E Unable To Ping Outside From Inside

Dec 1, 2012

I' d like to have some support for a very-basic PIX firewall configuration. I 'm dealing with  PIX 515E. Inside hosts can ping inside interface , outside hosts outside interface and so on. Simply i cannot ping outside interface from inside hosts, Inside host-192.168.1.0

Outside - any host like google.com, or to check my isp link's dns ip. I have attached the pix configuration text file to test.

View 10 Replies View Related

Cisco Firewall :: Allow Ping From Inside To Outside In 2900 Router?

Apr 7, 2013

I have a Cisco router 2900 with firewall, i need to know how can i allow the ping from self zone to outside zone, i trried to create policy from self to outside but i still didn't allow ping or tracert, i get that message when i try to ping from cisco router: "Unrecognized host or address, or protocol not running"

View 3 Replies View Related

Cisco Firewall :: Can't Ping ASA 5510 Inside Interface

Apr 13, 2013

I  ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]

View 5 Replies View Related

Cisco Firewall :: ASA5505 Cannot Ping Inside Host

Aug 2, 2011

I have Cisco ASA 5505  installed  and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM  and the VPN Tunnel is not working between the sie
  
ASA# ping 10.10.10.12
???????????
100% lost 
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
 
Here is the Topology
 
INTERNET .<=========================>ASA<===============================> LAPTOP
  
I disabled window firewall on the Laptop , but no goof result.

View 3 Replies View Related

Cisco Firewall :: ASA 5540 Want To Ping Across Inside To Outside For Testing

Sep 27, 2012

ASA 5540 8.2 (5)I have tried many combinations of command line syntax suggested in this forum but none are providing success so far.
 
I want to ping from the Inside Interface across to the Outside Interface and visa versa.I have tried various ACLs as well as "inspect icmp" in the config, etc still no go.
 
I can ping each interface from the console command line but cannot ping across each interface. [code]

View 1 Replies View Related

Cisco Firewall :: ASA 5520 - PING From Outside Into Inside Host

May 13, 2013

I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226".  Is it because I used dynamic PAT for inside hosts?

interface GigabitEthernet0/0nameif outsidesecurity-level 0ip address 198.24.210.230 255.255.255.248!interface GigabitEthernet0/1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0

[Code].....

View 3 Replies View Related

Cisco Firewall :: Cannot Ssh Or Ping ASA 5510 From Inside Interface

Apr 4, 2012

The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config. 
 
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names

[code]....

View 4 Replies View Related

Cisco Switching/Routing :: ASA 5505 Cannot Ping From Inside Interface To Outside Interface

May 1, 2012

I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside.  I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue.  When I ping 4.2.2.2 for example I get:
 
Destination host unreachable
 
Do I need to add a static route from my inside interface to my outside interfaces?   

: Saved
:
ASA Version 8.2(5)
!
hostname pxasa

[Code].....

View 2 Replies View Related

Cisco Firewall :: Failover ASA 5505 - Setup Second Inside Interface On Firewall?

Feb 19, 2012

I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?

View 1 Replies View Related

Cisco VPN :: Cannot Ping From Outside To Inside Site To Site IPsec 5505

Oct 28, 2012

I have a very basic lab site to site vpn setup where I have a ASA 5505 running v7.2(4) on one side and a cisco 2811 on the other side.

What's my issue?

I can't seem to ping from cisco router to the 'inside' network of ASA (see config below) and can't seem to ping from ASA packets leaving the 'inside' interface to cisco router even w/ an ICMP ACL permit outside in. However I'm able to ping within ASA inside network & ping cisco 2811 side w/ packets leaving ASA 'outside' interface just fine.
 
example:
-------
ciscoasa# ping inside 10.20.20.1 (to cisco loopback1 from ASA inside)
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.20.20.1, timeout is 2 seconds:
[Code].....

View 6 Replies View Related

Cisco Firewall :: ASA 5505 - Can't Reach FTP Site While Inside Firewall?

Feb 26, 2011

I am trying to configure our ASA 5505 so that our users can access our ftp site using [URL] while inside the firewall. Our ftp site is setup so that you can reach it by either browsing to the above url or by browsing to ftp://99.23.119.78 but we are unable to access our ftp site from either route while inside the firewall. We can access our ftp site using the internal ip address of 192.168.1.3.
 
Here is our current confguration:
 
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif ATTsecurity-level 0pppoe client vpdn group ATTip address pppoe setroute !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveobject-group service DM_INLINE_TCP_1 tcpport-object eq ftpport-object eq ftp-dataport-object eq wwwaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in extended permit tcp any interface ATT eq ftp access-list ATT_access_in extended permit tcp any interface ATT eq ftp-data access-list ATT_access_in extended permit tcp any interface ATT eq www access-list 100 extended permit tcp any interface ATT eq ftp

[code]....

View 6 Replies View Related

Cisco Firewall :: 2800 Routers / ASA 5510 Cannot Ping Via Route Inside?

Mar 3, 2013

I recently added a business cable modem to relieve some of the congestion I was getting on my T1 for our MPLS network.  There was an ASA 5510 collecting dust in a closet here and I thought it would be the perfect device for firewalling the traffic coming in from the Cable modem, and handling the routing of our internal MPLS traffic as well.  Internet setup was cake.  The test laptop I have using the ASA as it's gateway has great internet service but it cannot ping across either of our MPLS networks.  I have one MPLS with AT&T and one MPLS with EarthLink.  My hope was to use the cable modem as the Default route for all unspecified internet traffic and route our internal MPLS traffic to the cisco 2800 routers that are currently in place for the MPLS.  I can ping across the MPLS when I telnet to the ASA, but I cannot ping across the MPLS from the client that is connected to the ASA.
 
Here's the topology I'm working with
 
Internet
|
Cable Modem
|
ASA 5510 10.52.120.23

[Code].....

View 8 Replies View Related

Cisco Firewall :: Unable To Ping Inter Interface (inside To Outside) Of ASA 5520

Jul 26, 2011

I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1). 
 
ASA Version 8.4(1)
!
hostname FW5520

[Code].....

View 10 Replies View Related

Cisco Firewall :: Unable To Ping Host From Inside Interface From PIX525

Feb 3, 2012

When I tried to upgrading PIX525  6.3 to  7.0 , Not able to Ping the host from the PIX 525 Inside interface  which is on the same subnet,  Also from the host to Inside Interface ,  Tried with Directly connected  laptop with Cross cable and using Straight cable via switch, But the  results end with fail.

View 2 Replies View Related

Cisco WAN :: 2811 - Cannot Ping Inside Global IP From Inside Network

Dec 18, 2010

I have 2 questions.Om my cisco 2811 (IOS 12.4(15) T9 IPBASE W/O Crypto) i am using 3 interfaces.And i have a pool of Global addresses: 200.x.z.97-200.x.z.126 255.255.255.0
 
FastEthernet 0/1 description WAN interfaceip nat outsideip address 200.x.y.253 255.255.255.0
 
GigabitInterface 0/2/0description DMZ interfaceip nat insideip address 10.0.0.1 255.255.255.0
 
GigabitInterface 0/3/0description LAN interfaceip nat insideip address 192.168.0.251 255.255.255.0
[Code]....

View 8 Replies View Related

Cisco Firewall :: Access And Ping Inside Interface Of ASA5505 From Remote Network?

Sep 13, 2012

I am trying to access and ping the inside interface of a ASA5505 from a remote network.  From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface.  From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP.  When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
 
Here are the subnets involved and the ASA5505 config.
 
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24

[code]....

View 1 Replies View Related

Cisco Firewall :: Pix 515E Cannot Ping Or Assign DHCP Addresses To Inside Clients

May 6, 2011

I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG.  I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP  table  from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address. 
 
FW1 - CONFIGURATION
 
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0

[Code].....

View 3 Replies View Related

Cisco Firewall :: 5505 DNS Does Not Resolve Inside DMZ

May 14, 2012

I have a 5505 that currently has inside/outside interfaces and everything is working just fine. I am trying to create a DMZ that will essentially be just for vendors/guests. the DMZ will have full access to the outside (Internet) but no access to the inside. I am using the FW for DHCP, and 8.8.8.8 and 4.2.2.2 for DNS. I currently have 1 laptop in the DMZ vlan, and it is getting a correct IP, and it is showing 8.8.8.8 and 4.2.2.2 in ipconfig. I can ping/tracert 8.8.8.8/ 4.2. 2.2/74.125.137.147(what url... resolved to on a laptop connected to the inside vlan), but I cannot ping nor browse to url.... [code]

View 1 Replies View Related

Cisco Firewall :: Enable SIP From Outside To Inside (ASA 5505)

May 14, 2012

We recently purchases the Cisco ASA 5505 to get familiar with it, possibly buying more appliances for our branch offices. However, since the appliance is installed, our SIP telephones no longer register with our SIP service provider.
 
The SIP phones are all on 10.0.1.0/24 while the SIP provider is external via the outside network. I copied our configuration below. how to enable SIP for all 10.0.1.0/24 hosts and ports 5060, 5160, 5260, 5360?
 
gcxfw# show running-config
: Saved
:
ASA Version 8.4(3)

[Code].....

View 2 Replies View Related

Cisco Firewall :: 5505 DMZ To Inside ASA 8.4 / ASDM 6.4

May 21, 2012

I have a standard ASA 5505 with inside, dmz and outside with the default security levels, 100/50/0. we have an email server inside which has been NATed and is working fine. However users accessing the wireless on the dmz are unable to access their emails on https (443). How do I allow SSL access ONLY to users on the dmz using ASA 8.4 commands or ADSM 6.4?

View 10 Replies View Related

Cisco Firewall :: ASA 5505 - Allow (outside) Host To (inside)

May 20, 2011

I have a ASA 5505 Sec Plus. I would like to allow outside hosts to our mail server and also our FTP server. So i would like to allow only SMTP, HTTP (for Outlook Web Access) and FTP.

View 10 Replies View Related

Cisco Firewall :: NAT With Inside / DMZ VLANs On ASA 5505 V8.4(2)?

Sep 16, 2012

I have a 5505 with Base license running ASA software v8.4(2) that has been working happily for a while with an inside and an outside VLAN.
 
The outside has a single statically configured public IP, and I have a number of static NAT rules to expose a few internal servers as well as Dynamic-NAT for all devices on inside to gain access to the Internet... the main bits of the config are below:
 
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2

[code]....

I now have a requirement to add a "dmz" VLAN for guests to have access to the Internet using a dedicated wireless AP, but not to any of the inside resources. As the ASA has a base license I have configured "no forward interface" to the inside vlan, which suits the purpose fine
 
interface Vlan12
description Used only for guests access to the Internet - no access to the corporate resources
no forward interface Vlan1
nameif guests
security-level 20
ip address 192.168.2.1 255.255.255.0
 
My problem is that when I try to add NATing from the dmz to the outside I get a:
 
     ERROR: Address a.b.c.d overlaps with outside interface address.
     ERROR: NAT Policy is not downloaded
 
with either:
 
object network guests_subnet
subnet 192.168.2.0 255.255.255.0
nat (guests,outside) dynamic interface

[code]....
 
Having had a look at the ASA Configuration guides, all the examples I can see with several "internal" VLAN's being NAT'ed use one external IP per VLAN - is this a feature/restriction of the ASA software? Are there any workarounds? Or is the overlap in the error message really about the current NATing to the inside VLAN which is done on the "any" 0.0.0.0 subnet - would the following then work:
 
object network obj_any
subnet 192.168.1.0 255.255.255.0
nat (inside,outside) dynamic a.b.c.d
object network guests_subnet
subnet 192.168.2.0 255.255.255.0
nat (guests,outside) dynamic a.b.c.d

View 5 Replies View Related

Cisco Firewall :: Connect Inside To Outside In ASA 5505?

Apr 2, 2013

I have a test ASA 5505 with the setting below:

How can I connect to the internet (Vlan 1 to VLan 11)
 
[code]....

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved