Currently we have a T1 for data connected to a 1721 Router that is connected to an ASA 5510. We would like to add a FIOS line for dedicated online backup. Is it possible to connect the FIOS router to the ASA and route the IP from our backup server to use the FIOS line and everyone else continue to use the T1?
View 3 RepliesWe have an issue with some NAT on an ASA 5510. Here is a simplified drawing of the ASA setup:So the issue is when we try to send traffic from 172.16.3.251 to 1.1.1.1 we got this message in the log:
Oct 18 2011 12:32:12: %ASA-3-305006: portmap translation creation failed for udp src inside
172.16.3.251 /37166 dst outside:1.1.1.1/23
It looks like there is an issue with NAT but maybe is cause of the DUAL ISP setup as packets are routed through the outside interface and not IPtelefoni_outisde?
I have ASA5510 with PLUSE License.I have 2 Inside interfaces as STAFF and MAIL and two Outside interface OUT_STAFF and OUT_MAIL which is in separate ISP's.now i want to nat STAFF to OUT_STAFF and MAIL to OUT_MAILbecause I'm having two default routes it gets impossible to do.
View 1 Replies View RelatedWhat we are trying to accomplish here use two ISP's (one cable and one T1), use the Cable line for site-to-site VPN and use T1 line for all internet traffic. We currently use the following configuration: Cisco 2820 routers terminating the T1 -> HP switch -> Cisco AS 5510 port 0 -> port 1 to LAN switch (Nortel 5510)We want to force all VPN traffic (using 10.0.0.0/24 subnets - 10.0.1.0, 10.0.2.0, etc) through a cable connection, perhaps on port 2 of the ASA, then all non VPN traffic goes to the T1.
View 1 Replies View RelatedI am in the process of configuring a ASA 5510 to replace an older PIX. This change is part of migrating to a new ISP, so the process is complicated by the existence of two outside interfaces. I have virtually everything working, but there is a requirement to be able to access hosts from the internal networks using both their private IPs and their public IPs. The older PIX took care of this silently with little configuration, but the ASA has me twisted on the details. Some of the hosts with public IPs are on the internal network and some are on a DMZ (not my design, inherited). For the internal ones I implemented hairpinning to take care of the requirement, but I am having trouble with the DMZ based hosts.. Since there are two external interfaces each internal host has two IPs and two static NAT rules to handle incoming traffic from each external interface.
The routins and dynamic NAT entries we have in place take care of accessing the hosts using their private IPs on the DMZ, but I cannot figure out how to get the public IPs to work from the internal network. It seems like a simple Static D-Nat shoudl do it, but when I add a Static D-Nat on the DMZ the public IP works, but the private IP breaks.. Is there a way to get them both to operate ?
Network layout looks like this (IP ranges altered):
DMZ 172.10.0.0.0 Class C
INTERNAL 10.0.0.0 Class C
Outside 1.2.3.0 Class C
Outside2 2.3.4.0 Class C
[code]....
After applying it I could access the public IP (1.2.3.50) from the internal network, but I could no longer access the DMZ IP (172.10.0.2) from the internal network. Is there any way to get this configuration to allow access to both IPs from the internal network ?
The problem here is that there are website links based on the public IP and the DNS is split so DNS returns the internal IP to users. As a result both need to be accessible from the internal network.. Not my favorite design, but the client (or in this case the boss) is always right so I need to get it working somehow.
I am having a strange requirement. actually I am not sure it is strange or not. I am having ASA5510 with 8.4 sw version. Currently one ISP is connected to it. It is working fine. We have some servers that are directly connected to internet using another ISP connection. These servers having public IP addresses configured on their LAN settings. I need to move these servers in to the DMZ zone.
When i connect it to the ASA's DMZ zone,servers will get internet through the first ISP that is already configured on ASA. But i need to NAT the DMZ servers with the IP address provided by the other ISP, which even not configured on ASA.
So what should i do? In short my requirement is
1) need to NAT the server with the IP address provided by another ISP
2) Also note that the default route is configured for the first ISP only in ASA
so Do i need to configure another default route? Do i need to make it with larger AD? So i do it will act as the secondary route only.
I need to make the ASA up and running for two ISP, and servers in the LAN should be able to NAT with the IPs of first ISP and ,the servers in the DMZ zone should be able to NAT with the public IP of the new ISP.
We have plans for multiple ISPs and need to pick the correct device/architecture for that. single site: 3 ethernet hand offs (1 From ATT Fiber/10Mb pipe via their managed router, another one from ATT via Copper T1 via a separate circuit & managed router and the 3rd/last from Cable Modem/Comcast)
1.WAN hand off from another ISP from I will use ASA 5510 (already have) to use all the above 4 as inputs and then use the internal interface of the ASA 5510 as the default gateway for all the employees to browse the internet etc. so that1. If one one or more of the ISP lines die, we continue to operate (albeit lower bandwidth)
2. Also, we take advantage of the added bandwidth (even though it may not be the arithmetic sum of all the above).
I need to know how to setup my ASA with dual wan links. 1 is 10/10 fiber, other will be a 50/5 Cable Wideband link. The 10/10 fiber is currnetly being used for VPN's and Internet, (about 20 point to point IPSEC vpn's currently).
I want to add the Wideband link and use the "Tunneled (Default gateway for VPN traffic)", feature for the current fiber link and the new Wideband link for any other internet traffice. I tried this however as soon as I set my fiber link to "Tunneled (Default gateway for VPN traffic), I lost all connectivity.
I also setup my "VPN" link with the "tunneled" option and my "INTERNET" link with a default route to the internet. This would only let me ping internet sites from the ASA device but not from client computers, also the VPN's would not come backup.
I have tried the sla setting with a DSL line for failover and that works good, i've since got rid of the DSL and want to utilize 2 wan links for different purposes/traffic.
ASA 5510, SSM-10 1GB RAM
ASA version 8.4(1)
ASDM Version 6.4(3)
Context Mode Single
FW Mode Routed
License Security Plus
Looking to replace an "all-in-one" type firewall (UTM/Firewall, SSL VPN) with a cisco product - the issue i'm running into is that we have multiple ISPs plus WAN and DMZ - overall more than 5 ports on mid-range ASA devices - and from what i read, adding 4-port module precludes me from adding CSC module.
Is there an solution to that other than going for 5585-x model? (kind of over our budget, granted we need 2 for failover)
We have a cisco ASA 5505 with sec bundle plus
We have two ISP's:
ISP1 (Our IP = 30.100.150.50, gateway 30.100.150.8)
ISP2 (Our IP = dynamic, gateway 20.100.150.9) - ADSL
Our internal LAN IP range is 10.9.8.0/24
We want to configure the ASA 5505 to allow users via ISP2 for http traffic We then want to use ISP1 for strictly VPN and access to internal web resources (eg OWA) as we have public IP's there.
Our idea was to configure two gateways on the ASA (e.g. 10.9.8.5 via ISP2 and 10.9.8.6 via ISP1)
Then give the users gateway 10.9.8.5 for web browsing etc Is this configuration possible on the ASA 5505?
Site A has an ASA 5510 and a single internet connection.Site B has two internet connections (primary and backup). If Site B also has an ASA, I can configure Site A's ASA to deal with a failover at Site B (set peer 1.1.1.1 2.2.2.2). Does this work if Site B has an IOS router instead of an ASA? In other words will "set peer 1.1.1.1 2.2.2.2" on the ASA work when it's talking to IOS on the other end?
View 15 Replies View RelatedI have a Cisco ASA 5510 and I am trying to set it up to be able to have it failover to the 2nd ISP connection if the 1st one ever went down. I think I need a nat statement that the "backup" connection will use when the 1st connection goes down, but I am unsure what the nat statement is supposed to be. I have added the commands that I am pretty sure that I need to add for the "backup" ISP connection. Attached are those commands, the interfaces that are set up, and the objects that are set up in the ASA.
View 2 Replies View RelatedI inherited a network redesign project mid implementation and ran across an issue that I was not 100% sure able to be resolved. Implementation is occurring in which the organization is changing over to a different ISP and we have some customers that will not be able to change their settings over to our new addresses from some time. I have seen a lot of posts about fail over and dual ISP configurations, but I could not relate them to this particular scenario.
View 3 Replies View Relatedhave a PIC 515e connected to two ISPs via 2 interfaces. ISP1 is a 3.5Mbps aDSL line, and ISP2 is a 30Mbps business cable. I've confirmed the speeds by connecting the cabled directly into a laptop and using wget to download very large files from known-fast sites.
For admin reasons, I need to access two specific subnets using the slower ISP1. The rest of internet traffic should go to the much faster ISP2.
So I configure ISP2 as the default gateway, static routes for the two subnets to ISP1, set up NAT (PAT) and it all works like a charm. I've confirmed that ISP1 is used for only the two subnets, and ISP2 for everything else. CAPTUREs on the pix also confirm this. So far, it all works great.
But for reasons I don't understand, my max. download speed is 3.5 Mbps (the slow DSL). Using various speed tests and wget, I simply cannot get a download speed faster than my 3.5 Mbps DSL line.
Here is my config:
interface ethernet0 100full
interface ethernet1 100full
interface ethernet2 100full
[Code]....
I have an ASA 5505 current f/w & the security plus license (to get the 3 nameif interfaces). Can I split traffic between two ISPs, (VPN traffic to one destination on a T-1 on one VLAN, and all other traffic using DSL to another VLAN) and using a different nat policy on both? I know load balacing isn't supported, only failover. I was just wondering if there was a way to make this work.
View 3 Replies View RelatedLooking to have an ASA5510 with two internet feeds. Moreover, I would like to have my static nat translations continue to work on the backup feed. I have outbound nat working, however I cannot get the inbound nat to work. I had this all figured out in 7.x but now with 8.x I cannot seem to get it working. If anyone has a 8.x example config.
View 4 Replies View RelatedI am setting up an ASA550 ver 7.2(3) - does this need upgrading?I have my ISP interfaces setup as primary and backup I have a static route pointing out:route primary 0.0.0.0 0.0.0.0 1.2.3.4 1 Question:Do I put the next static route to be route secondary 0.0.0.0 0.0.0.0 3.4.5.6 254 Will this set a high metric on the secondary route that will only take effect if the primary route is down? I assume I will need to have 2 sets of NAT rules to accommodate the dual ISP's
View 1 Replies View RelatedI need to know if the cisco ASA next generation specially ASA 5515X support PBR or no ?how to implement it? Also if i have many internet connections and i need to dedicate 2 ISP’s ADSL internet lines to certain service (such as mail) if the 1st fail, so the 2nd line come up to make redundancy with it ----------- Is this available on cisco ASA next generation.
View 1 Replies View RelatedLately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
View 4 Replies View RelatedI have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 4.2.2.2 i dont get any reply.The runing config is below for ur ref :
HQ-ASA-01# show running-config
: Saved
:
[Code]......
I need to create a firewalled segment that not only separates hosts from general population, but also from each other. The solitary confinement of firewalled segments.I know that I could create a bunch of sub-interfaces, one for each host or group that needs to be isolated, but I'd really rather not have to do that if possible. 1) It could become a management nightmare between ACLs and sub-interfaces and 2) it's a waste of IP addresses.s there any way that I can create a bunch of separate VLANs behind the firewall and have them all terminate at the firewall, using a single firewall IP address for the gateway?
VLAN 1 - hosts 1.1.1.5 and 1.1.1.6VLAN 2 - hosts 1.1.1.7
Firewall DMZ Interface - 1.1.1.1VLAN 3 - hosts 1.1.1.8 and 1.1.1.9
This way, the hosts are isolated and can't talk to each other unless they're on the same VLAN.I'm working with an ASA 5510 running 8.2.4(4).
I have a ASA 5510 firewall with CSC module and Security Plus license for CSC module.Will you tell me how to configure my firewall to send emails to particular mail ID when someone login into the firewall or any virus attacks from outside.
View 6 Replies View RelatedWe were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies View RelatedI would just like to to open UDP port 123 in the ASA 5510 Firewall so that our Primary Domain Controller could use this port to sync time with an external time source. We have already added an access rule for this port under the firewall configuration in ASDM 6.4 and this port was also allowed in the inbound and outbound rule of the PDC's Firewall but it seems that it was still blocked.
View 23 Replies View RelatedI am quite new to firewall, in my company one asa 5510 firewall is there.I configured inside, outside, dns, dhcp and nating.I need to config bandwidth limit (1Mbps) for inside port and I restruct like facebook, youtube and pornsites..And I heard that some subscription is required, really is it required?
View 1 Replies View RelatedI have an ASA 5510 in a live environment. Up til a short while ago I could access this via the ASDM and ssh. However I can no longer connect to it via eithier. When I access It via SSH I get a disclaimer saying the following
*** You have entered a restricted zone! Authorized access only!!! Disconnect immediately if you are not authorized user! ***
It then cuts me off.
When I try to access the ASDM I get the following
The firewall is running all its services without a problem and I can ping the device without any issues. Also none of the config (to my knpowledge has been changed). I set up a console session and http server enable is still there with
http 192.168.200.0 255.255.255.0 inside
I have just configured identity firewall on our ASA 5510.I have 3 nodes that authenticates against Active Directory, using the Windows Server 2008 R2 builtin Network Policy Server: A laptop, a stationary PC, and a Android Phone. All 3 nodes are authenticated using the same user/password.
Now, in ASDM -> Monitoring -> Properties -> Identity -> Users, I can see two of the nodes with my user name attached to it, namely the laptop and the stationary PC.But not the Android phone.
Then it dawned on me. To set up the ADAgent properly, you have to apply 2 group policy entries. Unfortunately, those 2 entries are applied to the Computer Configuraton part of the Group Policy.This means that your COMPUTER has to be a member of your domain for USER IDENTITY to work.So my Android phone and other nodes not a member of the AD Machine Store will never be detected by identity rules, and can roam the network free.
I'm trying to install an ASA 5510 transparent firewall using ASA version 8.4(3)9 but I don't understand how traffic will ever pass through my firewall if both interfaces are on the same sub net(V lan) as the host and it's default gateway? The reason I'm doing this is were installing UAG (or Direct Access) and the UAG appliance need to have public IP's but still be behind a firewall (see attached diagram).
Looking at the documentation (which all seems to be for 5505's running 8.2) it almost seems like i need to have the transparent firewall 'in-line' to the ISP router?, but this router services another IP address range on another v lan for other (routed) firewalls (not shown on diagram) so putting it 'in-line' is not possible. Surely this can't be the case can it? If not how is it supposed to be cabled up and configured so packets go through the firewall?
I currenty have 2 cisco 5510 firewalls one of the firewals is completly dead but contains a Cisco ASA SSM-10 can i remove this card and just place it into a working unit, will i have any problems doing so.
View 1 Replies View RelatedI am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br Interface IP-Address OK? Method Status Protocol Ethernet0/0 x.x.x.x YES CONFIG up up Ethernet0/1 x.x.x.x YES CONFIG up up Ethernet0/2 unassigned YES unset administratively down down Internal-Control0/0 127.0.1.1 YES unset up up Internal-Data0/0 unassigned YES unset up up Management0/0 192.168.1.1 YES CONFIG up up
This is my first time to use the Cisco ASA 5500 family. I have a request from a user to create an access rule, to allow all LAN traffic to Destination IP address 165.241.29.17, 165.241.31.254 with Destination TCP port 5060,5061,5070 and UDP port 50000-52399.
View 9 Replies View RelatedWe have setup new ip camera system and as per our vendor to access the camera from outside we need to open,TCP ports and in firewall and forward to our camera server.
Let say our public ip address is 207.114.111.22 and our local ip address for the camera is 11.11.1.30. We have cisco asa 5510.
We've in our company a Cisco Asa 5510 v8.4(3), Asdm 6.4(7) and a SSM-CSC-10-K9. The firewall is in transparent mode. I get an exchange 2003 SP2 server behind. When users trying to send mailing lists with many recipients (above 300), the Exchange server didn't send these mails. I'm pretty sure that this problem come from the ASA Firewall, because when I plug my server directly on my Internet Connection, the mailing list is sent. I've search on the web, and disable "ESMTP Inspection", but it didn't work. [code]
View 4 Replies View Related