I would like to use an ASA5505 as a simple LAN-to-LAN ethernet router. My plan is to configure two interfaces with the same security level and then use the command that allows interfaces with the same security level to communicate with each other. I can get this to work without having to setup and ACLs or NAT stuff.
View 5 Replies
I have two router Cisco 887 with vpn site-to-site:
Site A:
crypto isakmp policy 1
encr 3des
authentication pre-share
crypto isakmp key ********* address 85.34.AAA.AAA
!
crypto ipsec transform-set strong esp-3des esp-md5-hmac
[code]....
I want to remove VPN configuration from the router and put VPN Configuration on Cisco ASA 5505.The scheme would be: ASA5505(vpn site-to-site) -> 887 -> INTERNET this for both sites.My problem is that I do not know what ip put on interface Outside of firewall. For example on Site A delete all VPN configuration from 887 and leave only ATM0.1 point-to-point, on intereface Outside of ASA put ip of loopback(of router 887) and as default route 85.34.2.XXX. Right?
I am a beginner to ASA. I am trying to connect the ASA 5505 behind the netgear ADSL router which is getting dynamic IP address from the ISP. How to configure the ASA5505 outside interface for SSL VPN connectivity?
View 8 Replies View RelatedI have a normal setup of ASA5505 (without security license) connected behind an internet router. From the ASA5505 console I can ping the Internet. However, users behind the Firewall on the internal LAN, cannot ping the Internet even though NATing is configured. The users can ping the Inside interface of the Firewall so there is no internal reachability problem. In addition, I noticed that the NAT inside access list is not having any hit counts at all when users are trying to reach the internet.
When i replace the ASA5505 with a router with NAT overload configuration on it, the setup works normally and users are able to browse the internet.
The ASA5505 configuration is shown below.
hostname Firewall
interface Ethernet0/0
description Connected To Internet Router
switchport access vlan 10
[Code].....
i have asa 5505 with the asdm v5.2 (4), and the asa v7.2(4). This platform has a base license. if i upgrade adsm and asa on v6.2(1) and v8.2(2) if I lose my license and that you need to activate them? i configured site to site vpn (this firewall and the another) that i lose my configuration if i upgrade my firewall.
View 2 Replies View RelatedI've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
View 32 Replies View RelatedInternet ISP -> Juniper SRX 210 Ge-0/0/0
Juniper fe0/0/2 -> Cisco ASA 5505
Cisco ASA 5505 - >Inernal LAN switch.
1. Internet is connected to Juniper Ge0/0/0 via /30 IP.
2. Juniper fe0/0/2 port is configured as inet port and configured the Internal public LAN pool provided by the ISP. And this port is directly connected to Cisco ASA 5505 E0/0. Its a /28 pool IP address. This interface is configured as outside and security level set to 0.
From Juniper SRX, am able to ping public Internet IPs (8.8.8.8).
Issue:
1. From ASA am unable to ping public ip configured on Juniper G0/0/0 port.(/30)
2. From ASA no other Public internet IP is pinging.
Troubleshooting Done so far.
1, Configured icmp inspection on ASA.
2. Used the packet tracer in ASA, it shows the packet is flowing outside without a drop.
3. Allowed all services in untrust zone in bound traffic in Juniper SRX.
4. Viewed the logs when I was trying the ping 8.8.8.8 in ASA. It says "Tear down ICMP connection for faddrr **** gaddr **
I'm trying to troubleshoot an ASA5505.
The original goal was to block "Mumble/Murmur" (a voip app) traffic, which runs on TCP/UDP 64738, both inbound and outbound, except to a certain host (63.223.117.170).
However, when nothing I tried seemed to make a difference, just to troubleshoot, I decided to try blocking all inbound traffic. I first disconnected ethernet port 0/0 to ensure that it was cabled correctly and the outside interface went down when I did. That worked as expected, so I confirmed I had the right interface and it was cabled correctly.
I then applied a "any any deny ip" rule as the first element in the outside interface access_list, as you can see below. However, it appears to have had no real effect and the hit count is very low (it should be astronomical).
show ver
Cisco Adaptive Security Appliance Software Version 9.0(2)
Device Manager Version 7.1(2)
Compiled on Thu 21-Feb-13 13:10 by builders
System image file is "disk0:/asa902-k8.bin"
[Code].....
Is it possible to use IP "aliases" on an ASA5505 to use as static NAT public IPs to private IPs? For example, I have int e0/0 connected to my ISP using a /30 subnet and I have my private LAN connected to e0/1 with a /24 subnet. At the moment I can use the one usable IP from the /30 to NAT to the private LAN. The ISP is also routing a /28 subnet to the one public IP of the ASA. I would like to use some of the /28 IPs for NAT also. Can it be as easy as just adding the NAT commands? I figure I would have to add that subnet to the ASA somehow, no? In other devices (including the SA520) they use a concept called IP aliases whereby you define what additional IPs the device can use in its NAT config. Does the ASA support aliases? Maybe I have to do something with VLANs?
View 2 Replies View Relatedit is possible use 1 or 2 Gb memory with ASA 5505 or only 512 Mb ?
View 3 Replies View RelatedI have 1 network that I'm trying to make secure, and it needs to access 2 seperate networks. I tried using an ASA5505 that I had on the shelf to accomplish this but discovered that I had the basic license and that was prohibiting me from getting my connection to my 3rd network. I scrapped that idea and grabbed an old pix 501 off the shelf to bring my connectivity to my 3rd network online since the 3rd network is only passing ip traffic to a small group of servers on the outside I figure the 501 should be just fine.
So, here's the problem I am running into:My internal network is 10.10.16.0/16, I have a new domain controller with DHCP on it handing out addresses in the 10.10.16.0/24 range.External Network 1 is 192.168.16.0/24. The services I need from that network are primarily in 192.168.0.0 range, however there is a comcast router 75.123.123.123 (Changed of course) that provides high speed internet I need for my www traffic.External Network 2 is 10.1.1.0/16 I have about 4 servers I need to access on this network and that's it. This network has it's own domain and DHCP controller and I've been given a range of ip's to use on this network of 10.1.3.180-10.1.3.189 My switch is just a plane jane 3com switch with minimal management so I am attempting to use my ASA5505 to handle my layer 3 routing.
So here's my issue:ASA5505 (IN:10.10.16.1, OUT: 192.168.16.6): Passes traffic to External Network 1 and to the comcast router, no problem. All my computers on my 10.10.16.0/16 network have access to everything on 192.168.0.0/24 as well as getting full name resolution and www traffic across the comcast router. Can NOT access 10.1.1.0/16 no matter what. From inside the ASA or from on the inside LAN ports. It CAN ping the PIX 501 PIX 501 (IN:10.10.16.3, OUT: 10.1.3.180) Can ping EVERYTHING. Can ping 192.168.0.0/24, can ping 10.10.16.0/16 and can ping 10.1.1.0/16. Set to globally assign the other IP's in my range as addresses for outgoing traffic.Workstations (IN: 10.10.16.XXX DHCP, using 10.10.16.1 as gateway) Can only access everything on External Network 1. ZERO access to External Network 2. ATM I have both INSIDE and OUTSIDE ACL's wide open for both firewalls just to get connectivity going. I will be tightening it up after it is operational.Attached find a log file (Sensetive data removed of course) that contains the sh run and sh ver for both the ASA5505 and the PIX 501.
I just got an ASA 5505 with Cisco Adaptive Security Appliance Software Version 8.0(4) alredy loaded on it. Should I update/upgrade it to the newest IOS release, or is the 8.0(4) good and stable?
View 3 Replies View RelatedI'd like to setup a DMZ network with the ASA5505. Do I need the "Security Plus Bundle"?
View 1 Replies View RelatedI've been trying to get my WRVS4400N connected to my ASA5505 on the internet through a Cox connection, but it isn't working. I cannot get the ASA to be the DHCP server for the wireless router. I've configured the wireless router as a gateway and pointed the DHCP server to the ASA but no addresses are being passed through to the wireless router. I've included a copy of my config.
ciscoasa# sh run
: Saved
:
ASA Version 8.4(2)
[Code].....
We are trying to utilize a 5 ip block of addresses provided by our ISP. What we have assigned from them is like this: 10.10.10.46 - 10.10.10.50 is our ip range. 10.10.10.45 is the gateway. Subnet is 255.255.255.248. If we assign 10.10.10.46 to the outside interface how do we accept inbound traffic from the other addresses?
View 6 Replies View RelatedI have Vlan 100 (inside) and Vlan 65 (Outside)I'm trying to configure RDP and ping traffic from Vlan 100 to Vlan 65 One way.If I connect 2 PCs on E0/0 and E0/1 they can happily ping the their own VLAN ip add 192.168.100.3 and 172.16.65.1I've copied my config,
ASA Version 8.4(4)1
!
names
!
object-group network A_Network
network-object 172.16.65.0 255.255.255.0
[code]....
I have a asa 5505 Sec plus with 3vlan, inside, outside and dmz.
On the outside i have 5 ip's for my use, and in the dmz i have a webserver that need to communicate with one sql server on the inside.
The "sql" also needs to be accessible from outside and thus has a static nat with a dynamic nat so it replies from same ip as on nat ie 72.72.72.5 webserver is natted with 72.72.72.6
sql inside ip is 192.168.1.2, gw 192.168.1.1
webserver ip is 192.168.2.100 gw 192.168.2.1
sec lvl on inside is 100 and on dmz 50
with a dynamic policy running inside-net/24 to dmz-network/24 translagt to dmz 192.168.2.2 i can get it to ping 1 way from inside to dmz, but not the other way around...
All i need is to open 1 port ie 6677 both ways for this communication to work.
I'm not very familiar with the CLI and do most stuf in GUI (know i should learn CLI, but time doesnt let me)...
on access rules i have just added everything from any to any using , ip, icmp, tcp and udp just to be sure... :-)
I want to make it so if a user tries to use a different DNS server the request will be redirected to the one they should be using.I thought this might work but the ASA doesn't do PB routing
ip access-list extended transparent_dns
permit udp any any eq 53
route-map redirect_dns permit 10
match ip address transparent_dns
set ip next-hop ip.of.your.server
route-map redirect_dns permit 20
[code]....
The DNS server is windows 2003?Would policy based NAT or WCCP work for this? If so how would I go about it?
for the purpose of a redundency, incase the primary ISP goes down the backup kicks in.Can this be done with the basic license (max 3 vlans) or you need to have the security plus license. (20 vlans) Currently not using the 3rd vlan (dmz)
View 5 Replies View Relatedsetting up ASA to allow passive FTP connection! I can get the FTP client to connect but it does not pull the directories. I have opened 21 and range of 55536-55566. I had some trouble gettting the range opened and saved. Normally with other small business routers (GUI) I make sure those ports are forwarded and ftp works.
Is the ftp inspection killing connection or is it my config?
ASA Version 8.4(2)
!
hostname ciscoasa
enable password vRLm0eRL2O14iLM6 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[Code].....
Do some have some realistic performance numbers for a ASA 5505 on a mixed setup with local internet breakout and site to site vpn ( and don't tell me 150 mbps 3des throughput on a 100 mbps ethernet) - what can be expected in a live environment where we f.ex feed it with a 100 mbps internet connection - with a site to site vpn with f.ex 20 office workers running office on a remote terminalserver and mixed local internet breakout.
View 2 Replies View Relatedcustomer's WAN solution, instead of buying routers, purchasing department bought ASA's (don't even get me started!). So I have 5 ASA 5505's for the branch offices and one 5510 for the Head Office. I am trying to get them to behave like routers and pass the traffic across. I set up a lab with a 5505 and the 5510 using an ethernet cable for both Outside interfaces since the WAN links are going to be MetroEthernet Layer 2 anyway.
I tried static routes, dynamic routing, I followed examples from other persons who did it and it doesn't work. I attached the configs here to show I have the default routes, specific static routes pointing the traffic out, any any rules configured as well. I cannot ping from the internal lan of the 5505 to the internal lan of the 5510.
I used the GUI configuration tool for this ASA 5505. When I install it no traffic passes. I am wondering to verify my config. I have masked the usernames for VPN with xxxxxx and yyyyyy. [code]
View 6 Replies View RelatedI have ASA 5505 running 7.2.4, I want to prevent users accessing some web sites such as facebook , youtube and hotmail etc.
Which ASA 5505 IOS version should I use to block web access?
I don't want to isntall a dedicated filtering server ( websense etc) , I just want to block web sites statically on ASA 5505 via ASDM as I only have few sites to block.
know if ASA 5505 can do URL filtering, and what IOS is required ?
I have 10 user license for Cisco ASA, i have to use this ASA for client connectivity. Can i do NAT of more than 10 users with this license? What i understand is NO.
But as per Below explaination looks like, i can if i am not doing default routing? Actually i just need to add a specific Route towards client DMZ interface on my ASA, no default route, so can i use more than 10 concurrent sessions with this license?
I have a cisco asa 5505 firewall, and I have a normal home ADSL broadband router, the router currently connects via wireless to my pc.What I would like to do is basically connect the asa to my pc, then my router to my firewall.what the best thing to do here, run the aa in transparent mode, OR routed mode and do NAT on the firewall to the private ip address range of my router.
OR, would it be possible to get the outside interface of my asa to get DHCP from my broadband router so it will use a 192.168.1.x address on the outside, and then turn NAT off?
Users cannot download some files from a FTP in a software over VPN Explanation users work with a program and inside the program they download claim (the software goes to the FTP and download the file)
But the program returns an error 3018 in FTPGET. If the user goes to the old PPTP VPN it works like a charm so the problem is the Cisco VPN.
I cannot post my complete config but we use the filter vpn value to associate a special access-list to a user.
The user that has this problem has this as an access-list.
access-list 201 extended ip permit 10.250.128.0 255.255.255.0 192.168.202.0 255.255.255.0
I've made some research and i've added this info
policy-map global_policy
class inspection_default
Inspection ftp
Still doesn't work.
I have to add that normally the internal network is 2.0 and not 202.0 but since we have user with 2.0 at home we had to do this.
So when a user sends a request to 202. the cisco fowards it to the Juniper inside the network and it translate it back to 2.0 Also that is the ONLY thing that doesn't work. The client can work all day on that program and it will work #1 exept when she does the claims
I am also been working on this VPN for 2-3 months without any problems.
We just took on a new client and they do not have the username or password for their ASA 5505. we need to reset to factory defaults. I have read some instructions online how to do this, but they require the password. How do we do it without the password?
View 4 Replies View RelatedI have interited an ASA5505 problem. We're trying to manage the ASA remotely - we can connect to the device remotely via IPSec, we can ping other devices on the LAN network, but cannot ping the inside interface of the ASA - nor can we telnet/ssh/http to it. We can, however, connect to another router that's on the LAN and then SSH into the ASA's inside interface.
My IP via VPN: 10.133.20.8
The ASA interface we're trying to connect to via SSH or ASDM: 10.4.209.254
A router on the LAN we can connect to 10.4.209.250
We can ping other LAN devices such as 10.4.209.75, .90, .150 - so it's not a NAT/Route/Split Tunnel issue.I've attached the ASA config.
hostname ASA5505
enable password XXXXXXXXXXX encrypted
passwd XXXXXXXXXX encrypted
names
name 10.4.209.248 rpm_router
[code]....
I am in the process of adding a lot of servers to sit behind our new ASA 5505 (8.4) firewall. At the moment I have added 2 servers and they are both NAT'ed to 2 different public IPs.
Server 1 192.168.10.1 -> 80.*.*.1
Server 2 192.168.10.111 -> 80.*.*.6
The first server can only be RDP'ed in to using its public IP which is what I want it to do. The second one has most of the service ports open like 443, 80, 110, 25 and etc. However when I try and browse externally to [URL]. I get an " Error 107(net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error." in Google Chrome or any other browser. and the ASA reports:11:27:30192.168.10.111262680.*.*.6443Inbound TCP connection denied from 192.168.10.111/2626 to 80.*.*.6/443 flags SYN on interface inside and I also get a Land to Land attack detected from 80.*.*.6 to 80.*.*.6
Is it worth setting up a DMZ or can I get away with the setup I have?
Ive migrated from my lab pix to a lab asa and am trying to open certain ports to my internal network.
in my confg on my pix i had acls to open port 51413 to an inside host along with the static nat rule.
what i am trying to accomplish is same on my asa, however the nat rules seem to be slightly different, and i'm not completely sure how to do it.
My ACL and nat rule is below. I'm pretty certain my acl is correct,but i am not sure as to what to do with my NAT rules to allow a translation for the tcp service.
access-list outside-in extended permit object tcp51413 any object outside nat (inside,outside) source dynamic all-inside-nat interface
I am very new to Cisco ASA and I am trying many days to implement the design below but still cannot get it done. The situation I am facing is
- a host (e.g. 192.168.5.10) under Inside interface can contact to outside without any problem.
- however a host outside (e.g. in VLAN1 or outside this network) cannot contact host under Inside interface. I am using PING test and always get Request Time Out. [code]
I would like to find out if security plus license ASA-5505-sec-pl be applied to ASA5505-K8. I think the strength of encryption should not be determining whether additional feature can be applied or not, but I need to confirm with you people..
View 1 Replies View Related
