Cisco Firewall :: ASA5505 Can't Ping New Firewall On Inside Interface

Jul 14, 2011

I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.

View 32 Replies


ADVERTISEMENT

Cisco Firewall :: Access And Ping Inside Interface Of ASA5505 From Remote Network?

Sep 13, 2012

I am trying to access and ping the inside interface of a ASA5505 from a remote network.  From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface.  From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP.  When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
 
Here are the subnets involved and the ASA5505 config.
 
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24

[code]....

View 1 Replies View Related

Cisco Firewall :: ASA5505 - Can't Ping Inside Host

Sep 29, 2012

I just try to ping a internal Host but it want to go.
 
Laptop<===>ASA5505
 
Connected is the Laptop at Ethernet 0/2 Inside
 
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
 
But If I try to ping to the Laptop I get the followed:
 
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
 
From the Laptop to the ASA5505 I can Ping successfully.

View 6 Replies View Related

Cisco Firewall :: ASA5505 Cannot Ping Inside Host

Aug 2, 2011

I have Cisco ASA 5505  installed  and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM  and the VPN Tunnel is not working between the sie
  
ASA# ping 10.10.10.12
???????????
100% lost 
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
 
Here is the Topology
 
INTERNET .<=========================>ASA<===============================> LAPTOP
  
I disabled window firewall on the Laptop , but no goof result.

View 3 Replies View Related

Cisco Firewall :: ASA5505 Icmp Denied For Inside Interface?

May 6, 2012

I have ASA5505 configured with internal network as 192.168.15.0  and default gateway 192.168.15.1 From the inside network, i'm able to access internet and able to ping all website (enabled ping).   and all internel  network devices can ping each other.  Except  i cannot ping my gateway (ASA5505) 192.168.15.1.  I'm continously seeing this message on the log, when i tried to ping.. How to fix this?
 
Denied ICMP type=8, code=0 from 192.168.15.xxx on interface inside
 
replace xxx with my network devices that try to ping the gateway..I dont want outsiders ping my gateway, i need ping for inside internal network only.

View 5 Replies View Related

Cisco Firewall :: ASA5505 Using Outside Interface To Connect To Multiple Machines Inside

Oct 28, 2011

I have been working on a configuration for single IP address (on outside ) of ASA5505.I am trying to utilize the outside address 192.168.0.249 to PAT/NAPT to 10 inside machines [code]
 
What I am not sure of (actually that could be considered all encompassing) is the mapped services/real services.Any constructive comments assistance?

View 5 Replies View Related

Cisco Firewall :: New ASA 5505 / Can't Ping Inside Interface

May 10, 2011

I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?

View 1 Replies View Related

Cisco Firewall :: Can't Ping ASA 5510 Inside Interface

Apr 13, 2013

I  ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]

View 5 Replies View Related

Cisco Firewall :: 5505 - Can't Ping ASA Inside Interface

Dec 12, 2011

I have an ASA 5505 that I'm trying to set up a guest network on.  I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it.  The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
 
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
 
[code]....

View 4 Replies View Related

Cisco Firewall :: Cannot Ssh Or Ping ASA 5510 From Inside Interface

Apr 4, 2012

The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config. 
 
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names

[code]....

View 4 Replies View Related

Cisco Firewall :: ASA 5505 / Cannot Access Internet Or Ping From Inside Interface?

Jul 26, 2011

I am having a problem configuring my ASA 5505 for NAT.

View 3 Replies View Related

Cisco Firewall :: Unable To Ping Inter Interface (inside To Outside) Of ASA 5520

Jul 26, 2011

I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1). 
 
ASA Version 8.4(1)
!
hostname FW5520

[Code].....

View 10 Replies View Related

Cisco Firewall :: Unable To Ping Host From Inside Interface From PIX525

Feb 3, 2012

When I tried to upgrading PIX525  6.3 to  7.0 , Not able to Ping the host from the PIX 525 Inside interface  which is on the same subnet,  Also from the host to Inside Interface ,  Tried with Directly connected  laptop with Cross cable and using Straight cable via switch, But the  results end with fail.

View 2 Replies View Related

Cisco Firewall :: ASA5510 - Unable To Ping From User Desktop To Firewall Inside IP

Jun 11, 2012

I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to  FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
 
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:

[Code].....

View 7 Replies View Related

Cisco Firewall :: Failover ASA 5505 - Setup Second Inside Interface On Firewall?

Feb 19, 2012

I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?

View 1 Replies View Related

Cisco Firewall :: Unable To Ping Internet IPs From ASA5505 Firewall

Jan 9, 2013

Internet ISP -> Juniper SRX 210 Ge-0/0/0
Juniper fe0/0/2  -> Cisco ASA 5505
Cisco ASA 5505 - >Inernal LAN switch.
 
1.  Internet  is connected to Juniper Ge0/0/0  via /30 IP.
 
2. Juniper fe0/0/2 port is configured as inet port and configured the Internal public LAN pool provided by the ISP. And this port is directly connected to  Cisco ASA 5505 E0/0. Its a /28 pool IP address. This interface is configured as outside and security level set to 0.

From Juniper SRX, am able to ping public Internet IPs (8.8.8.8).
 
Issue:

1. From ASA am unable to ping public ip configured on Juniper G0/0/0 port.(/30)
2. From ASA no other Public internet IP is pinging.
 
Troubleshooting Done so far.
 
1, Configured icmp inspection on ASA.
2. Used the packet tracer in ASA, it shows the packet is flowing outside without a drop.
3.  Allowed all services in untrust zone in bound traffic in Juniper SRX.
4. Viewed the logs when I was trying the ping 8.8.8.8 in ASA. It says "Tear down ICMP connection for faddrr **** gaddr **

View 2 Replies View Related

Cisco Firewall :: Outside To Inside Not Work ASA5505

May 8, 2013

I am very new to Cisco ASA and I am trying many days to implement the design below but still cannot get it done. The situation I am facing is

- a host (e.g. 192.168.5.10) under Inside interface can contact to outside without any problem.
- however a host outside (e.g. in VLAN1 or outside this network) cannot contact host under Inside interface. I am using PING test and always get Request Time Out. [code]

View 12 Replies View Related

Cisco Firewall :: Allowing Traffic From Inside To Outside ASA5505 7.2(3)

May 15, 2012

Let me start by saying that I'm just starting to study for CCNA, so the ASA seems to be a bit above me yet.  The ASA's we are using is for VPN to our corporate office and only allowing access to our Citrix environment, so no direct internet allowed.  We have a person who works in the remote office who has need for a caption telephone that requires direct access to the internet.  The phone only supports DHCP, and getting the ASA to do an ARP reservations is proving difficult.  For now I wrote an access list to allow it's DHCP address out but it still isn't working.  The access list I wrote is:
 
access-list 101 extended permit ip host xxx.xxx.xxx.124 any log
access-list 101 extended permit ip any any
access-group 101 out interface outside
 
When I do a show access-list I'm seeing that traffic is hitting the access list as the hit counter has increased.  When I do a show conn I'm seeing one of the IP's that the phone should have access to, however the flags are: saA, so I'm assuming they are not getting a response.  According to the manufacturer, only outbound connections are needed, no incoming ports required.  All traffic is TCP.

View 8 Replies View Related

Cisco Firewall :: ASA5505 - Inside Hosts Limit

Feb 18, 2012

The ASA5505 I am working with has this from the show version:
 
Licensed features for this platform:Maximum Physical Interfaces : 8VLANs                       : 3, DMZ Restricted Inside Hosts                : 10Failover                    : Disabled VPN -DES                     : EnabledVPN-3DES-AES                : Enabled VPN Peers                   : 10WebVPN Peers                : 2Dual ISPs                   : Disabled VLAN Trunk Ports            : 0
This platform has a Base license.
 
Does the Insides Hosts  :10 line mean that only 10 devices can be connected to the firewall at one time? I would like to connect an AP to one of the PoE ports and have possibly more than 10 connected. Is this possible with this ASA5505? 

View 9 Replies View Related

Cisco Firewall :: PIX 501 / Can Traffic Goes From Inside Interface To Outside Interface

Oct 9, 2011

I have Pix 501 firewall and I'm just configuring the device for "Email Server" to allowing POP/SMTP.
 
Inside Interface Address: 132.147.162.14/255.255.0.0
Outside Interface Address: ISP provided IP address
 
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
 
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80
Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53
Pix(config)#access-group outbound in interface inside

View 7 Replies View Related

Cisco Firewall :: ASA5505 Cannot Access Inside Network From IPSec VPN

Jan 20, 2013

I'm trying to make a very plain and simple network with the ASA 5505, I've strated from scratch over a dozen times triyng to find where I'm going wrong.  My main goal is to simply create an IPSec VPN connection to my ASA 5505 and simply ping and connect to devices with the "inside network", so far I can easily create and establish a IPSec VPN Connection, but up to this point, I cannot successfully ping or access a single device on the ASA 5505 inside network.I've taken, create the IPSec profile with the ASDM wizard, add exemption for the VPN IP Pool, add access-list from this Cisco link, url...All this and I can't make a single connection to the inside network.  [code]

View 7 Replies View Related

Cisco Firewall :: Upgrade Inside Hosts From 10 To Unlimited On ASA5505 BUN K9

Aug 17, 2011

I want to  upgrade  "inside hosts" from 10 to unlimited on a ASA5505-BUN-K9, Do I have to buy  Security Plus license ( L-ASA5505-SEC-PL =)  ) before activating ASA5505-SW-10-UL ?

View 3 Replies View Related

Cisco Firewall :: ASA5505 (8.4.2) How To Access Inside SBS-Server On SMTP / RDP

Oct 25, 2011

Using an ASA5505, have 1 static outside address, want to access an inside SBS-Server on SMTP, RDP (3389), HTTPS and port 987
 
Have configured network object nat rules using the asdm, SMTP works (I can telnet to the server on port 25 from outside), however for some reason I can not telnet inside and out on port 25, so outgoing mail does not work. RDP does not seem to work from outside, 987 I havent tested from outside. When I try to create a network object nat rule for https I get this message from the ASA:
 
[OK] object network SBS-HTTPS
 object network SBS-HTTPS
[ERROR] nat (inside,outside) static interface service tcp https https
 NAT unable to reserve ports.

View 5 Replies View Related

Cisco Firewall :: ASA5505 - Outlook Access For Inside Hosts

Apr 25, 2011

I am using ASA 5505 firewall with base-license. I connected my firewall to one cisco 3750 switch where i created 5 vlans. I done NATing for all vlans and they able to get internet and working fine. They able to  browse all internet sites like gmail and yahoo mail.
 
All internal users are configured to use Outlook for their webmail. Here the problem is with outlook they are unable to send and receive the mails.
 
If they directly connected their system using public ip( Directly from ISP) they able to send and receive mails from outlook.

View 2 Replies View Related

Cisco Firewall :: ASA5505 Port Forwarding For Inside Server

Dec 20, 2011

I have installed ASA5505 in the network. Port forwarding has been done for one of the server in our LAN. Public users are able to access the server successfully. I am trying to access from inside using the same Public server IP, but unable to access it. Can I have this feature in ASA5505(I think it is loopback configuration). If so, may I know the configuration detail?

View 4 Replies View Related

Cisco Firewall :: Cannot Ping To Inside Hosts From ASA-8.2

Jun 8, 2013

I am struggling to get successfull pings beween asa and inside hosts but couldn't succeed. Done packet tracer result is acl-drop
 
Here is the running config
 
Prem-ASA(config)# sh run
: Saved
:

[Code].....

View 7 Replies View Related

Cisco Firewall :: ASA5510 Cannot PING From Inside To Outside

Jul 1, 2012

I cannot seem to determine exacly why I am not able to ping from the inside to outside using the standard 100/0 security levels respectively. I am dynamic natting the inside to the outside interface, something I don't usually do but cannot see why ICMP's are not passing through.
 
The Packet trace tool says there is something in the ACL but there really isn't.
 
Is there simply an issue of Natting to the WAN interface on a 5510?

View 10 Replies View Related

Cisco Firewall :: ASA 5505 Ping Inside To Outside Don't Go

Sep 29, 2012

I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
 
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
 
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
 
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254

View 2 Replies View Related

Cisco Switching/Routing :: ASA 5505 Cannot Ping From Inside Interface To Outside Interface

May 1, 2012

I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside.  I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue.  When I ping 4.2.2.2 for example I get:
 
Destination host unreachable
 
Do I need to add a static route from my inside interface to my outside interfaces?   

: Saved
:
ASA Version 8.2(5)
!
hostname pxasa

[Code].....

View 2 Replies View Related

Cisco Firewall :: ASA5510 - Cannot Ping Inside Over VPN After Upgrade

Jan 16, 2012

We currently have a central hub using an ASA5510 and then a few site-to-site VPN connections to our support staff homes. The devices at the homes are Cisco routers. We were running version 8.25 on the ASA and all was working fine. We recently upgraded to version 8.42 and although all the functionality of the network is ok and it does what it should, our support staff cannot ping, ASDM or telnet to the ASA inside interface anymore whereas they could before the upgrade. The home VPNs all run on a 10.30 subnet (i.e. 10.30.1.x, 10.30.2.x etc etc). I can post our config (security edited of course), but it is quite a big config. The command management-access inside is specified and the 10.30.0.0/16 subnet is permitted to ASDM and Telnet. Are there any extra things that have to be done in version 8.42 to get this to work as the support staff do have to access the firewall for configuration purposes. At the moment, they have to telnet to one of the routers on the local LAN and then Telnet to the firewall from there.Prior to the upgrade, they were all able to ping the inside ASA interface and also telnet and HTTPS to it from their PCs at home. Now they cannot and the only change made was an upgrade to 8.42. Immediately after the upgrade none of them can ping the interface anymore and it seems it can only be accessed from the local LAN. I cannot find any access-lists that might be blocking the packets so can only assume it's something in the way 8.42 works.

View 8 Replies View Related

Cisco Firewall :: PIX 515E Unable To Ping Outside From Inside

Dec 1, 2012

I' d like to have some support for a very-basic PIX firewall configuration. I 'm dealing with  PIX 515E. Inside hosts can ping inside interface , outside hosts outside interface and so on. Simply i cannot ping outside interface from inside hosts, Inside host-192.168.1.0

Outside - any host like google.com, or to check my isp link's dns ip. I have attached the pix configuration text file to test.

View 10 Replies View Related

Cisco Firewall :: Allow Ping From Inside To Outside In 2900 Router?

Apr 7, 2013

I have a Cisco router 2900 with firewall, i need to know how can i allow the ping from self zone to outside zone, i trried to create policy from self to outside but i still didn't allow ping or tracert, i get that message when i try to ping from cisco router: "Unrecognized host or address, or protocol not running"

View 3 Replies View Related

Cisco Firewall :: ASA 5540 Want To Ping Across Inside To Outside For Testing

Sep 27, 2012

ASA 5540 8.2 (5)I have tried many combinations of command line syntax suggested in this forum but none are providing success so far.
 
I want to ping from the Inside Interface across to the Outside Interface and visa versa.I have tried various ACLs as well as "inspect icmp" in the config, etc still no go.
 
I can ping each interface from the console command line but cannot ping across each interface. [code]

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved