I have a cisco ASA 5520 that i'm configuring.From the actual Firewall (with is a linux server), we have the outside interface eth0 with has a public IP and other sub-interfaces (eth0.1; eth0.2,...) with others publics IPs.I'd like to know how I can configure it in an ASA
View 7 Repliesi have an ASA 5520 running ver 8.4(1). have attached my interface config below and need to do the following, NAT traffic coming on GigabitEthernet0/2.101 to GigabitEthernet0/1, i.e. packets with destination 10.21.110.25 will be forwarded to 10.11.21.25, will a nat (Production,Advocate_MPLS) static ... statement work ?
------------------------------------------------------------------------
interface GigabitEthernet0/1
description Production
nameif Production
security-level 100(code)
We have an ASA 5520 which is in multiple context mode. We are trying to pass traffic from the outside interface to the dmz interface. We have a /27 public ip range. We need a small amount of those addresses to be in the DMZ for SIP servers specifically. The rest of the addresses are NAT'd to the inside interface.So i created the outside interface GigabitEthernet0/0 with 1.2.3.192/28 Inside Interface GigabitEthernet0/2 with 192.168.20.0/24 DMZ interface on GigabitEthernet0/2.1 with 1.2.3.208/29 So all i want to do is route traffic that comes in the outside interface and out to the DMZ interface for the 1.2.3.208/29 subnet. I set the gateway address as 1.2.3.214 which is the DMZ interface address on the ASA.
View 20 Replies View RelatedOur ASA 5520 firewall is running 8.0(4) IOS.I have an internal L2L VPN terminating on my firewall (from an internal remote site) on ENG interface.With the default "sysopt connection permit-vpn" command enabled, VPN traffic is allowed to bypass the ENG interface acl.The security level on the ENG interface is set at 50.The security level on the destination interface PRODUCTION is set at 40.Inbound VPN traffic bypasses ENG interface acl and since higher-to-lower security level allows VPN traffic to flow freely from ENG to PRODUCTION, it seems the only place to check/filter VPN traffic is an ACL placed on the PRODCTTION interface and set at INBOUND (outbound VPN traffic).
View 4 Replies View RelatedI have a Cisco ASA 5520 running 8.2.2 with the VPN Plus license. I am wondering what is the max number of sub-interfaces you can have on a physical interface. I know on the 5505 it was 20 sub-interfaces if you were running the Security Plus license. What is the magic number for the 5520. I have hit 20 sub-interfaces on gi0/1 interface and now I am starting to run into problems with sub-interface #21.
View 1 Replies View RelatedI have two virtual interfaces on my ASA 5520:
GigabitEthernet0/1.338 172.30.0.81/28
GigabitEthernet0/1.345 172.30.0.129/28
I have the security levels for both set to 50 and in the ASDM I have checked off "Enable traffic between two or more interfaces which are configured with same security levels"
But now the need has arisen that we allow each subnet to be routable to each other for SMTP traffic, how can I accomplish this?
We have been testing out IPv6 configurations on a 5520 running 8.2(4). We have assigned EUI-64 prefix addresses to sub-interfaces to allow clients to auto-configure there IPv6 IPs and it works correctly. I used ASDM to do the original configuration and noticed that there were two different ways to do it, both of which seem to work. I can add a prefix under the Interface IPv6 Addresses dialog box and check EUI64 or I can add it under the Interface IPv6 Prefixes. But using the two methods yields two different interface configurations:
1.
interface GigabitEthernet0/1.40
vlan 40
nameif test
[Code].....
We have a Cisco ASA 5520 and in order to conserve public IP addresses and configuration (possibly) can we use the same public IP address for a static NAT with two different interfaces? Here is an example of what I'm refering too where 10.10.10.10 would be the same public IP address.
-static (inside,Outside) 10.10.10.10 access-list inside_nat_static_1
-static (production,Outside) 10.10.10.10 access-list production_nat_static_1
I have issue with traffic passing between same security level interfaces. I want to control traffic between same security level interfaces with ACL. Even no restriction, traffic does not go through. [code]
I tried to access server from THREE network to web server at FOUR network I have no response. In sh xlate output it shows "PAT Global 10.124.104.254 (28889) Local 10.124.103.1(2922) " I am not sure what else should I do. I add both same-security-level commands and it is the same.
One line of an ACL was changed on an ASA 5520 (primary) and a wr mem was issued to save the change. It appears that when the wr mem was executed, the interfaced on the standby ASA bounced. Configurations have been saved in the past without the result of what's in the log entry..
ADC-5520-MGMT-FW01/stby# show logSyslog logging: enabled Facility: 22 Timestamp logging: enabled Standby logging: enabled Debug-trace logging: disabled Console logging: level errors, 1203060 messages logged Monitor logging: level errors, 1203060 messages logged Buffer logging: level errors, 17590658 messages logged Trap logging: level informational, facility 22, 450126258 messages logged Logging to management 10.5.3.214 Logging to management 10.142.20.214 Logging to management 10.218.3.31 History logging: disabled Device ID: disabled Mail logging: disabled ASDM logging: level informational, 464351755 messages loggedSep 21 2011 17:35:29: %ASA-1-709006: (Primary) End Configuration Replication (STB)Sep 21 2011 17:35:44: %ASA-1-105006: (Primary) Link status 'Up' on interface managementSep 21 2011 17:35:44: %ASA-1-105006: (Primary) Link status 'Up' on interface outsideSep 21
[code]....
Got new ASA5550, code 8.2.2 in flash, can't configure "nameif" or "ip address" on the interfaces: [code] These are all the options that I get! Another weird thing I noticed is "<system>" string in "show ver" top line: [code]
View 2 Replies View RelatedWe have to enable FIPS 140-2 on our ASA5520's for all our IPSEC VPN connections. We currently have failover on our 5520's. I found a lot of information out there but some seems to conflict one another.What are the things I need to look out for - caveats? Does the clients that connect to the VPN had to use different clients once the FIPS was enabled.Do we need to recreate logical interfaces for each physical interface we have?
View 1 Replies View RelatedI am trying to figure out how to create an etherchannel with sub-interfaces on an asa 5520 running 8.4.1 code. It doesn't seem to allow me to configure any type of sub interface on the port-channel or anywhere else once I create it.
View 4 Replies View RelatedI have a pix515 v6.3.3. Is it possible to configure dual ISP on two interfaces and have redundancy between them?
View 1 Replies View RelatedI have a an ASA 5520 connected to a Layer 3 (3750) switch (Inside) and a connection to a 2960 switch (Outside) to get to the internet. . I have created vlan interfaces on the 3750 switch and enabled ip routing on the switch to enable the vlans to communicate with each other.
Vlan Interfaces on the switch:
Vlan 100 172.17.1
Vlan 200 172.18.1
Vlan 300 192.168.3.1
I want the devices connected to the 3 vlans to be able to pass through the firewall and get out to the internet.I have connected the ASA to the 3750 by routed interfaces (10.10.10.1) --------- (10.10.10.2) and they are able to ping each other.I have also put a default route on the 3750 sending all traffic from the switch to the ASA inside interface (10.10.10.1)The issue that i am having is that the ASA also connects to a 2960 which has a connection to the Internet, and they are handing off an ethernet connection from the 2960 that sits in VLAN 55 (Vlan 55 is the Internet accessible vlan).How do I configure my ASA to send all traffic from my (3) vlans to the interfaces that connects to the 2960 switch?
We have Cisco ASA 5520 firewall. ASA Version - 8.0(4). ASDM Version - 6.1(3). Firewall Mode - Routed.
We want to configure QoS for some subnets and enable policing such that they cannot use more than 1mb of bandwidth. I think we cannot create more than 1 policy for it. In that case i created a policy with QoS enabled and configured the Input and Output policing with Commited Rate of 1024000 bits/second. But it does not seem to work.
how can i create such policy in the ASA to limit certain subnets to 1mb bandwidth ?
i'm trying to configure an ASA with two ISP to be reached from internet for vpn access, the objective is that the user can use any of the Public address attached to ASA to connect to the company. Is this possible? i'm facing some problems because i can not use two different default routes (same AD) pointing to two different interfaces, this is the message that i receive "ERROR: Cannot add route entry, possible conflict with existing routes" and when i change the AD of one of the default routes i just can reach one ISP.
View 1 Replies View Relatedi have an ASA 5520 with ios 8.4 and asdm 6.4.
my configureation is below
my asa interfaces
inside ip
172.16.0.0/22
[Code].....
so now i want to configure my asa to give access to user based. what configurations should i use to do so.
i have attached the Edit Active Directory Server dialuge box so what should i put there in the box's
How to configure ASA 5520 to resolve names in ASA's. We are currently using ASDM to configure network objects with the hostnames in the internet and then specifying the IP address . But this is done manually. Is there a different way of setting it up on ASA. Also when getting reports from ASA, we see the IP's but is there a way that we could add an identity to the IP's (reverse lookup)
View 1 Replies View RelatedI have two ASA 5520 version 8.2 in active Standay Mode. What is a good practice to setup IPS AIM ssm-20 for this setup.
Is IPS should be in Fail-Open or Fail-Close mode ?
Is Mangement ip for both IPS module should be same or diffrent. ?
I am new to cisco ASA. I need to configure ASA 5520 in transparent bridge mode. [code] I need to place the new asa firewall in transparent mode. How to configure the firewall in transparent bridgmode.
View 5 Replies View RelatedWe already have a subnet defined to inside interface and is in produciton. the default gateway is this interface ip. In that setup now I have to add one more subnet and as the first subnet is been defined in ASA indside interface, I have to assign secondary Ip to the inside interface so that new subnet users can easily reach here and go outside.
View 1 Replies View RelatedBelow is my config for IP SLA. I would like a SNMP trap to be sent when my primary fails over to my secondary and so on.
sla monitor 20
type echo protocol ipIcmpEcho 100.X.X.1 interface INET-FIOS150
num-packets 2
[Code].....
Is it possible to import the config of a 5510 to a 5520. Trying to replace two 5510's with 5520's and wondering is there a way import the existing config files for the 5510's into the 5520's?
View 3 Replies View Relatedi have cisco ASA5520 and i have a remote access vpn .I want to configure logging for this remote access vpn.
i want the time user connected .how log it is connected .If any error while connecting ?
To show up the ASA as a hop in a traceroute, one can use the 'set connection decrement-ttl' feature in a policy map.During my tests I recognized, that this behaviour only affects IPv4 traffic.
An IPv6 traceroute still does not show the ASA as a hop.How can I configure the ASA to show up as a hop in an IPv6 traceroute?The ASA is a 5520 with v8.4(1) installed.
I have a asa 5520 with an outside and backup interface. I am trying to configure two static nat statements from the inside to the outside and backup interface. Here is what I have configured so far.
object network obj-10.1.1.254
host 10.1.1.254
object network obj-10.1.1.254
nat (inside,outside) static 172.25.10.3
I want to also use nat (inside,backup) static 172.25.10.3
We have two multilayer switches and only one ASA 5520. I'd like to connect ASA in the way described on the picture: each redundant interface includes two physical ones, which are connected to different switches
My question is what kind of link it is necessary to have between switches to make this idea work? I'd have subinterfaces like Re1.100, Re2.200 and so on for my traffic.
I understand that correct design approach is to have two redundant firewalls with failover but we cannot purchase the second one yet.
I have a question, it is possible to have two WAN interfaces to configure a cisco 892 router with an ip 255.255.240.0 84.197.167.111 adderess of the first interface and a different ip address 84.197.174.182 255.255.240.0 on the second interface
View 5 Replies View RelatedI've just started a CCNA course and my lack of knowledge has me a bit stuck. My network is comprised of Cisco components and I'm semi familiar with them just from reading and looking through options. I currently am using a Cisco ASA 5520 on my network and I am trying to join another network via one of the interfaces. My network is 192.168.0.0 255.255.0.0 and my inside interface is 192.168.1.1 255.255.0.0. I enabled a second interface using a static ip of 10.0.0.1 with a subnet of 255.255.255.128. Connected to that interface, I have a Fortigate firewall at 10.0.0.2 255.255.255.128. I can ping just fine from the Fortigate network to the 10.0.0.1 interface on the Cisco ASA 5520 network, but I can not ping the 10.0.0.1 interface (or anything past it) on the ASA 5520 from any computer on the Cisco network. I've read that ACL's and NAT have to be done as well as enabling traffic between interfaces with the same security levels. (both interfaces have security levels of 100 and the option is checked to allow traffic).
Note: each network has it's own internet connection. The connection is to share information on servers on both networks with each other.
I have an ASA 5505 with 3 host license.I want to configure 2 outside interfaces and have inside interface. The outside interface going to a separate ISP.Will this work or do I need more licences?
View 3 Replies View RelatedI have WLC 2504 controller and six access points AIR-LAP1042N. I reading Cisco 2500 Series Wireless Controller Deployment Guide url...trying to set up along the lines.
It is also possible to have multiple AP-managers in a different subnet than the management interface. However, in this case, it is recommended that you disable the AP-manager from the management interface and create another AP-manager interface on different physical ports in a different subnet than the management interface. All multiple AP-managers in this scenario should be in the same subnet.
I maping management interface on physical port 1 and disabled ap-manager on it. Set up 192.168.7.0 subnet with non tagged vlan. This iface/port I want to use only for access to WLC web-interface. Then I create dynamic interface ‘dynamic1’, map him on port 2, enable ap-manager on him, and set up 192.168.110.0 subnet with vlan 10. Then I tryed map wlan1 to this iface, but I can’t because in the choice was only management iface to map wlan1.
There is three dynamic interfaces on same subnet and vlan, in example above. But when I try to add dynamic iface with the same vlan/subnet as an existing dynamic interface, I get an error, and can’t adding.
On a 3750 switch, is it possible to configure jumbo frames only on certain interfaces and leave the other ones as they are?
View 9 Replies View Related