I am trying to forward both TCP and UDP ports 3074 but it looks like I can only have either TCP/3074 or UDP/3074 open one at a time. When I try to enter the UDP/3074 NAT statement, I get "ERROR: NAT unable to reserve ports". [code]
View 4 RepliesWe're trying to get a remote access setup for someone who needs to have access from offsite. To make things easy we set it up with a virtual machine running Windows 7 and RDP. Because the "other end" isn't our computer and we've had some difficulties with people using the Cisco VPN client successfully, we were just going to set up a machine as a RDP Gateway and forward the port through the firewall (WebVPN might be nice, but the plugins only do RDP through v5.x). I've tried this on 8.4-1 and after reinstalling the latest 8.2, and supposedly the NAT works and there is a firewall rule allowing access from the outside to the RD-GW server on HTTPS, but the ASA is still blocking those packets. I've looked at 4 howtos and followed them, trying from the console and from ADSM (and one trashed the whole setup, probably related to the reinstall of 8.2) - [code]
View 4 Replies View RelatedI need to forward some ports for remote desktop and remote outlook which I host on an internal server. I have looked all over the web and got close, but no hints on how to do it in the asa 8.2. there is an 8.3 guide, but it is just different enough to not work. I am new to this device and cli.
View 3 Replies View RelatedI have an ASA 5505 running 8.4(1), and I'm configuring it with ASDM 6.4(1). The outside interface is configured with a single static address. I have a few services port forwarded sucessfully to three different servers on the inside network.
I need to make a media proxy on a SIP server available to the outside. It requires a large range of forwarded UDP ports for the media channels.
I tried adding a network object NAT rule like the others I'm already using to forward HTTP and RDP. I entered a range of ports for the real port and the mapped port using the syntax 60000-60999. ASDM accepted it, but the NAT rule list displays "Any" in the service column. When I apply the change, I get the following error:
nat (inside,outside) static interface service tcp 60000-60999 60000-60999
^
ERROR: % Invalid input detected at '^' marker.
How do I forward a large range of UDP ports from the outside interface to a single server on my inside network? I'd like to use ASDM, but I can switch to the CLI if that works better.
i've a cisco asa5505 on adam 6.4 and a dvr i would like to forward the ports 9000 and 85 in order to monitor the dvr from outside?
View 1 Replies View RelatedI need the following ports forwarded for a single ip address Port 88 (UDP)Port 3074 (UDP and TCP)Port 53 (UDP and TCP)Port 80 (TCP) .Is there an easy way to to it with service objects/groups?
View 7 Replies View RelatedI've just bought a Cisco 887m-k9 and I am trying to forward the ports. I have a Polycom HDX H.323 device connected to it with a static IP of 10.10.10.5 (ethernet port 0).Previously I had a consumer grade Linksys router which worked fine (I simply entered ports into the GUI), but I couldn't hardcode LAN port speed so I bought this. I have the list of TCP and UDP ports which are forwarded using the following commands:
ip nat pool Polycom 10.10.10.5 10.10.10.5 netmask 255.255.255.0 type rotary
ip nat inside source static tcp 10.10.10.5 80 88.xxx.xxx.49 80 extendable
ip nat inside source static tcp 10.10.10.5 443 88.xxx.xxx.49 443 extendable
ip nat inside source static tcp 10.10.10.5 1300 88.xxx.xxx.49 1300 extendable
[code]....
Where 88.xx.xx.49 is my static IP, while 77.xx.xx.170 is my default gateway.
I had a DI 604 router and I couldn't forward ports, someone told me to buy a new router because my modem (TM602G) doesn't have a built-in router and can't be blocking it so I bought a DIR 601 with wireless and I still have the problem.I don't have any firewalls.
View 19 Replies View RelatedIve been having trouble opening any ports on my windows 7 desktop. I connect wirelessly to my D-link Dir 655. I've tried port forwarding single ports to a static ip, but that didnt work either. I currently have the dmz server enabled and still no ports are open according to this port checker Open Port Check Tool - Test Port Forwarding on Your Router I have the windows firewall service disabled, upnp is enabled on my computer and router, i have spi firewall disabled, qos is disabled, and endpoint tcp/udp filtering on endpoint independent.
View 3 Replies View RelatedI'm trying to open ports 2934 and 2935 UDP on my Linksys E1000 router in order to play Falcon 4: Allied Force multiplayer but it's not working.I've correctly created a static IP, and logged in to the E1000's page. Under "Applications & Gaming", and then under "Port Range Forwarding" I entered values thus:
[code]....
I cannot successfully forward ports on this router, I've tried a few things but I can only assume the firmware is bad. I've already looked around for a solution but everyone says they solved it by just getting a different router (which at the moment isn't an option).
View 3 Replies View RelatedI can't get port forwarding to work, even when I turn off the Windows 7 firewall and AVG anti-virus software I'm running. I entered the IP address of my laptop (with a DHCP reservation) and UDP and TCP port numbers, with Schedule set to Always and Inbound Filter set to Allow All. That should be it, right? However, when I check the ports using PFPortChecker, both the UDP and TCP ports are blocked. I do have a Linksys wireless router daisy-chained to the D-Link router, but I'm not communicating on this computer through the Linksys router and the problem still occurs even when the other router is disconnected, so that doesn't appear to have anything to do with the problem. I just updated to the latest firmware (3.13NA).
View 11 Replies View RelatedI have a router 1802 with a several vlans with IP 192.168.x.0/24 for each vlan (x, it meaning 1, 2, 3, 4, etc.).Now I need that an IP address outside from my network (this IP it is always the same) to be access to on particular machine that is in a private network (192.168.3.0/24) through a several ports:
25 (TCP,UDP), 80 (TCP,UDP), 554 (TCP,UDP), 2000 (TCP,UDP), 10002 (TCP,UDP), 10000 (TCP,UDP), 3000 (TCP,UDP), 3041 (TCP,UDP)
How can I do it?
Outside PC ---------Internet ----MyRouter -----MyParticularPC
83.240.194.99 193.136.80.1 192.168.3.1
how to forward ports using routers
View 2 Replies View RelatedI went out and upgraded to the E3200 a week or so ago and since then i've been unable to forward any ports. I've tried pretty much everything I can think of: disabling Windows firewall, setting a static IP for my computer, setting a static IP for the router, enabling forwarding in both single and range menus, DMZ etc.Here is a screenshot of the port forwarding page just to confirm that i'm doing nothing wrong:In the above photo you will see that I set the computers static ip to x.1.2 and I later changed it to a value that was within DHCP range as listed on the status page of the router admin gui and it still didn't work.So, what I ask of you guys is if you can think of anything that I must be fundamentally doing wrong in order for this not to work. Could it be that i'm missing some possible drivers or network utilities on the computer i'm trying to forward ports too
View 1 Replies View RelatedI am new to the RV180W. I am running the most recent firmware--version 1.0.1.9.
I am having trouble getting FTP to work with my QNAP NAS.
QNAP indicates that I should forward ports 55536-56559 to my NAS. I created a custom service to accomplish this, and then, under port forwarding, I selected the service and forwarded it to the private IP that corresponds with the NAS.
However, the port forwarding configuration only allows me to specify *ONE* internal port. With other routers I have always specified the same private port *RANGE* that corresponds with the public ports that I have opened up.
I'm trying to forward ports for SQL and VNC using these commands in the CLI:
ip nat inside source static tcp 192.168.1.150 5900 interface GigabitEthernet0 5900
ip nat inside source static tcp 192.168.1.150 5800 interface GigabitEthernet0 5800
ip nat inside source static tcp 192.168.1.150 1433 interface GigabitEthernet0 1433
where 192.168.1.150 is my server (that hosts SQL server and that I want to be able to connect to remotely using VNC) and GigabitEthernet0 is my configured WAN interface.
When I try to connect from an external client I get the error: "Failed to connect to server..." Is this a firewall issue? How do I get round it? The 819 is the only router/firewall in my network.
Need to port forward certain ports for one computer but need UPnP for 2 different ps3's.These are the parts I have. I have read that the GT704WGB does not have a true bridge mode. I don't want to bias anyone however. How to best use this equipment so that I can port forward ports on my laptop. There are also several laptops, desktop and phones on my network but the 2 ps3's and my laptop are what primarily concern me.
-Actiontec GT704WGB for Verizon DSL (Modem / Router Combo)
-Actiontec Support GT704WGB Wireless DSL Gateway for Verizon High Speed Internet access
Cisco Linksys wrt54gs v4 (Router) currently running Tomato firmware but I can flash dd-wrt back to it in a second.
I am attempting to forward port 25565 on my router, and having some trouble. I've set a static IP address as both 192.168.2.10 and 192.168.2.111, and attempted a dynamic IP address. The port forwarding page via 192.168.2.1 in the browser looks like this, with the Private IP Adress changed to whatever corresponding IP address I have set (checked with cmd /ipconfig).
After testing with multiple online port checking tools, the ports remain closed.
A client is thinking of putting in a srp527w. they get assigned a static ip on the adsl interface (165.228.204.x), and then have been assigned another block(203.39.183.x/29).how can i have it so that i am able to forward individual ports from the external ip's, to selected internal ip's.
View 1 Replies View RelatedHow do I forward ports on the N600 DB F9K1102v3? I have looked through everything. When I go to port forward, I enter the info and have it all down correctly, I click save and once it reloads it isn't there and the port isn't forward.
View 1 Replies View RelatedI need to forward several ports. however it has been complicated by a missing or corrupt default access gateway. [code] I am leaving for quite a while tonight, hoping to come back to a reply I am using a belkin router ( will get model number and stuff later - not sure if its needed ) * and wow cable and internet url...
View 8 Replies View RelatedI have a DSL modem, model AG10W. I can't seem to figure out how to forward ports to xbox. No one seems to have this router/modem. I got it from a company here in town. I don't know much about this type of stuff.
View 1 Replies View RelatedI'll try to keep it short. On this Games For Windows Live game (Dawn Of War II) I can connect to and play on the internet just fine. Enabled port 3074 and 88 so that GFWL wouldn't have any problems connecting to my computer. Port 3074 has an issue however.With the PortForward testing program (Open Port Check - PortForward.com), whenever I check port 3074 outside the game, both UDP and TCP show green and are forwarded correctly. However when I'm in the game, alt-tab, and run the test again, it shows UDP red after testing, indicating it's not forwarded correctly.I think I know precisely what the problem is; either something in GFWL or the game itself is blocking port 3074. But why it's doing this, and how to find out what it is, I really have no idea.
View 4 Replies View RelatedWe have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies View RelatedIs there a way to associate spare firewall ports with another port that is being used..For example...int gi 0/2 is being used currently for my web dmz. Its ip is 192.168.10.1..Is there a way for me to associate gi 0/3 with the same layer 2 as gi 0/2 ?
In my webdmz I use 2 ACE 4710 proxys in FT mode. I used a layer 2 switch to connect firewall and proxys together.
I would like to eliminate this switch if possible..and connect both 4710's (layer 2) direct to firewall.If I could make gi0/2 - 4 part of the same vlan, then I would be good to go.
Router 1
Cisco EPC2420
192.168.1.1Connects to ISP via F-connectorConnects to Router 2
Router 2
Asus DSL_N55U
192.168.1.2Connects to 192.168.1.12(Linux Server)
So I bought router 2 but since it doesn't have an F-connector input I need to keep router 1 in the infrastructure so I can connect to the internet.The port forwarding on router 1 is a limited list so I can only add so many rules and would rather have my router 2 do this as it alot better but i cannot seem to get it to work.So I set a rule in router 1 to forward all ports to router 2 and then setup the port forwarding in router 2 to send port 22 to my linux box but it didnt work.
I always seem to have problems when trying to configure port forwarding on cisco routers. I've even tried the instructions I have for a cisco 1811, but no luck. I have a cisco 871 and a computer that has VNC installed on it. I want to be able to access that computer from out side the network using the external ip address and port 5950. People outside the network will be able to open vnc viewer and type in *external ip address*:5950 and it will be directed to the computer with a static internal ip address of 10.12.0.10. What commands do I use to do this?
View 4 Replies View RelatedMy internet works. However port forwarding does not work. I want to port forward from the outside to inside obviously. I get an error in my log file which Ill show you and then I will share the running-config I have tried using this method found elsewhere.
========================================================================================================
ATTEMPTED CONFIG
object network inside-host
host 192.168.100.4
nat (inside,outside) static interface service tcp 3389 3389
access-list Outside-2-Inside line 1 extended permit tcp any host 192.168.100.4 eq 3389 log informational interval 300
access-group Outside-2-Inside in interface outside
[code]....
I'm trying to do a normal port forward on a ASA 5505 with 9.1(1) and it is not working as it should.There are two ports that I want to forward, TCP 32000 and TCP 32001, from the outside interface.I tried a Auto NAT that gave rpf-check drop. [code]
I have tried diffrent configurations on this for several hours now and I cant get it to work.Could this be asymetric NAT with the dynamic rule? How can I troubleshoot this in a smart way?
i´m trying to make a traditional port forward (http to http) on our new asa5510. Previous releases off 5505 and software prior 8.3 was no problem. Could someone tell me how do it in new 8.4 version? I ám a rookie on the new ASA series!
If nothing makes sense in this configuration please give example on how to do it correct. The object on the inside is SRV02 wich is running a webserver on port 80. So i want to open upp for http on outside interface and forward that traffic to srv02 (inside webserver)
I consider the NAT mechanism to be quite straight forward, but although the firewall ACLs allow the traffic, it is being denied. The ASDM log and packet-tracer indicate the problem being an ACL.
# the internal resource
object network mabe-mbp
host 10.0.0.36
!
# these are ALL of the rules on the outside/inside interfaces
access-list outside_access_in extended permit tcp host 1.2.3.90 any eq 12380 log disabled
access-list outside_access_out extended permit ip any any log
access-list inside_access_in extended permit ip any any log
access-list inside_access_out extended permit ip any any log (code)
Successfully creating a port-forward in ASA5510, ASA version 8.3(1) ASDM6.3(1)?I have spend hours now trying, but I'm still unsuccessful.What I want is a simple: "if this particular ip-adress hits the wan interface on this tcp-port redirect to this inside ip-address on this tcp-port.I have never had any trouble on any other firewall creating something like this, but the ASA is killing me.
View 10 Replies View Related