Cisco Firewall :: Provide Access To The Management Interface / Vlan On ASA 5505

Jun 8, 2011

I've got an ASA 5505 running 6.3 I've connected the management interface to our management vlan (which contains switch IPs, ilo's etc)Is there a way to allow access to this vlan from another?

View 1 Replies


ADVERTISEMENT

Cisco Firewall :: ASA 5505 Creating Interface Vlan In Firewall

May 3, 2011

I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???

View 4 Replies View Related

Cisco Firewall :: ASA 5505 - Unable To Assign IP To DMZ Vlan Interface

Oct 26, 2012

I have ASA  5505 with base license. I created 3rd  vlan on it.it was created. but i am unable to assign IP to it. i assign ip address it takes it. But when i do sh int ip brief it does not show any ip.
 
Code...

View 7 Replies View Related

Cisco Firewall :: Remote Management Access Through VPN On ASA 5505

May 21, 2012

I have a remote ASA5505 running 8.4(3) with a working site 2 site VPN tunnel to my main office. (The main office is running an ASA 5510 with OS 8.4.3 as well). The encryption domain is all private IP on main site vs. 172.16.10.0/23 on remote site.
 
Relevant config of the remote ASA:
 
interface Vlan1
nameif inside
security-level 100

[Code].....
 
I can manage the ASA on the outside interface (outside of the site 2 site VPN) using the TACACS credentials I can also ping my management station from the ASA using the inside interface, but as stated, the other way around does not work. I have not yet tested if management from the local 172.16.10.0/23 subnet works, but I will try this next.

View 5 Replies View Related

Cisco Firewall :: ASA 5505 Transparent Mode And Management Access

Apr 26, 2012

I have a need to manage the 5505 outside of the 2 interfaces however I see it documented that Management access is only via the data path interface. This won't work for me because there will be NO management access on the data network being bridged through the firewall. Is there any option outside of going to routed mode or moving to the 5510?

View 1 Replies View Related

Cisco Firewall :: SQL Server Access From DMZ Interface ASA 5505

May 25, 2011

I would like to allow users from network 10.132.23.0/24, 10.132.33.0/24, 10.132.24.0/24 access to our SQL server(192.168.1.7) located on the inside interface(192.168.1.0/24 network) Those networks (10.132.0.0/16) come from the DMZ interface.

View 12 Replies View Related

Cisco Firewall :: ASA 5505 VLAN Assigned To Outside For Internet Access

Aug 7, 2011

ASA 5505 and DMZ and Base License,"For example, you have one VLAN assigned to the outside for Internet access, one VLAN assigned to an inside business network, and a third VLAN assigned to your home network. The home network does not need to access the business network, so you can use the no forward interface command on the home VLAN; the business network can access the home network, but the home network cannot access the business network." Page 6-17.
 
This is exactly what I need. Mail server in DMZ, full access from internet to DMZ, and from inside network to DMZ, no access from DZM to inside network. If I good understand, this is possible with base license.
 
I successfully configure, internet Access for DZM and inside network, Mail server can be accessed from internet, as well as RDP on inside network. But I have problem to configure communication from inside network to DMZ. [code]

View 13 Replies View Related

Cisco Firewall :: ASA 5505 / Cannot Access Internet Or Ping From Inside Interface?

Jul 26, 2011

I am having a problem configuring my ASA 5505 for NAT.

View 3 Replies View Related

Cisco Firewall :: 5505 - Construct An Access List For Outside Interface Using External Address?

Sep 10, 2012

I'm configuring a 5505 for a remote office.  Until they are assigned a static ip by the provider I will have to use the providers dhcp address. How do I construct an access list for the outside interface using the external address if I don't know it yet? is there a commnd that will insert the ip address in to the access list once one is assigned?

View 5 Replies View Related

Cisco Firewall :: ASA 5520 - Routed Management Interface On Transparent Firewall?

May 5, 2013

I have an asa 5520.  How would I configure my dedicated management interface to be able to route off subnet while the firewall is in transparent mode?

View 1 Replies View Related

ASA 5505 - Can't Ping Any VLAN Interface

Aug 9, 2012

I'm trying to set up a Guest VLAN for wireless at a client site, and I feel like I'm missing something small in the configuration, since I can't ping any of the VLAN interfaces from my laptop when the address is statically set to something in the 172.20.100.x range.

I've pasted the configs for the ASA 5505 and the 6 switches below for convenience. Near as I can tell, all should be well. The ports are in trunking mode, the "show cdp neighbors" command returns the proper information, VLAN 100 exists on all the switches, etc.

Code:
ASA Version 7.2(4)
!
hostname ASA
domain-name xxxx.local
enable password Cj3LF.ehxXN3xVkxWcxd encrypted
passwd Cj3LF.ehxXN3xVkWcxd encrypted
[Code] ......

View 17 Replies View Related

Cisco Firewall :: ASA 5510 - Management Interface

Feb 13, 2012

I am having issues with the ASA 5510 management interface. I can't communicate with this interface. It is showing DOWN/DWON even if I type NO SHUT several times.
 
My existing config is as follows 
our-asa-01# sh run
Saved
ASA Version 7.2(5)
hostname our-asa-01
names
dns-guard
interface Ethernet0/0
[code]....

View 5 Replies View Related

Cisco Wireless :: WLC 5508 7.3 Management Interface Access To GUI?

Jan 16, 2013

After I've upgraded software to the v7.3 and applied AP-SSO it made imposible to access the controller's gui via Service-port. So we tried to access it by management-port, but there is some problem too. It is not working from another subnets. But default gateway on management vlan is set correctly and I even tried to turn of all acl's on switch. WLC is only accessible from the same network. But at the same time wlc is replying on ping fine.All other protocols cannot connect to the controller.

View 3 Replies View Related

Cisco Firewall :: ASA5512-X Setup Using Management Interface

Jun 28, 2012

I have a brand new ASA5512-X running 8.6.1, and am trying to do an initial setup using the Quick Start Guide that came with it.  However, the Management Interface is not working.  I have a PC connected and set to use DHCP, but the port is not active. I connected a console cable and can see in the config that the interface is shutdown.  So I set it to active, and the port is now active, but is not giving out a DHCP address as the guide says it should.I would like to use the ASDM Startup Wizard to configure this device, so how do I get it to work the way the instructions say it should?

View 2 Replies View Related

Cisco Firewall :: ASA5540 Management Interface IP Addressing?

May 9, 2011

How does one allow /31 mask for an management interface on an ASA5540 using version 8.3(1)?
 
I need to configure a 192.168.x.y /31 on the management 0/0 interface of a ASA5540 and it is providing me with the following error:ERROR: /31 mask is not allowed

View 1 Replies View Related

Cisco Firewall :: 5520 - Configuring ASA Management On Sub-interface

Jul 27, 2010

I have two ASA 5520 with 4 Giga interfaces and 1 management interface.
 
I need to use 4 interfaces four data traffic
 
1- Inside
2- Outside
3- dmz-1
4- dmz-2
 
The remaining will be the management interface only.How can I configure the Statefull failover and Management?
 
1- I used the management0/0 for The stateful failover.
 
2- I used gig 0 for outside
 
3- I used gig 1 for inside
 
4- I used gig 2 for dmz-1
 
5- I divided the gig 3 to two sub interfaces
a- gig0/3.1 for dmz-2
b- gig0/3.2 for Management and I defined it as a management-only

View 6 Replies View Related

Cisco Firewall :: Management Interface In Cluster ASA 5515x?

Jan 6, 2013

I have a misanderstand about management interface configuration in cluster. So I have a cluster asa 5515X with management interface. i Would like to be able to connect to any of the member of my cluster on management interface, so i would like to fix a different ip on management interface on each of my node ip 92 and 91. I think it is the only way to make asa firmware update to access local flash on each node.
 
my config
 
interface GigabitEthernet0/1
channel-group 1 mode active
no nameif

[Code].....

View 9 Replies View Related

Cisco Firewall :: ASA5510 - Cannot SSH Or ASDM To Management Interface

Jan 21, 2013

I try to SSH and get access denied.
 
I try to ASDM and get "Unable to launch device manager from 172.16.252.100"
 
I think I am missing something. Software is 8.4(5) and running in Transparent Mode.
 
Inside/Outside are in bridge-group 1. No BVI is configured as we will be using Management0/0 for access.
 
login as: test
test@172.16.252.100's password:
Access denied

[Code].....

View 7 Replies View Related

Cisco Firewall :: ASA5520 Use Management Interface As Regular

Oct 16, 2011

i have a Cisco ASA 5520 8.4(1) with a ASA 5520 VPN Plus license
 
i want to use the management interface as a regular interface (using the no management-only command)is this interface a Gig interface as well ?

View 1 Replies View Related

Cisco Application :: ACE 4710 - Cannot Access Management VLAN In Context

Jan 21, 2012

I have an HA ACE deployment and all seemed to be working well until I tried to access the ACE via the management VLAN in the one non-system context, no go.The ACE is in one-armed mode with an Admin/System context and one user context (named Messaging).  Source NAT has been set up in the user context.  All VLANs are in a port channel back to the core switches.I can access the ACE via the Management VLAN in the system context, all OK.  I can access the load-balanced servers via the VIP in the user/Messaging context, all OK.  I CANNOT acccess the managment VLAN other than ping it (resonds to ping, but telnet, ssh, https, etc. fails).The system/Admin context has a default route to the Management VLAN on the core.  The User/Messaging context has a default route to the core switches on VLAN 5, which is the VLAN where the VIP resides.If I change the default route in the User/Messaging context to the Management interface on the core switches then I can access both contexts for management, but then the load-balancing falls over and I cannot access the serverfarm (via the VIP).  Traces on the rservers show that NAT is being hit on the ACE and the requests are coming from the real IP of the clients.  Put the default route back to the User/Messaging VLAN on the core and NAT is back to what it would be expected to be, and then remote/management access to the ACE is gone.
 
ACE02/Admin# sh run

Generating configuration....
 
logging enable
logging standby
logging timestamp
logging buffered 4
logging device-id context-name

[code]....

View 1 Replies View Related

Cisco Switches :: SG 200-18 - Change Management-VLAN And Telnet / SSH Access?

Apr 29, 2012

We've got a SG200-18 switch that is to be used as a workgroup switch in our environment (SW Version 1.1.1.8). Working with CLI on big and mid-range Cisco-gear over the past two decades I'm having a hard time figuring out the following on the SG200:
 
o) I want to change the Management-VLAN from the default "1" to the management-VLAN used in our environment. Sure enough I created that vlan in the SG200-config, however when it comes to assigning the management-IP and VLAN for the management interface in the corresponding pulldown under "IPv4 interface -> Management VLAN" the only thing selectable is the default "1". (see screenshots enclosed)So how do I set a management VLAN different from 1?
 
o) How do I enable telnet/ssh-access to the SG200-18 - I'd be far more comfortable with a CLI-environment?

View 2 Replies View Related

Cisco Routers :: Cannot Access The Web Management Interface Of SRP521W-U From A Different Subnet

Oct 30, 2012

i cannot access the web managemnet interface of this router from a different subnet.THe WAN interface is a 4G LTE connection,I have disabled both the SPI firewall and NAT and enabled remote management from any ip address but i cannot access the admin web page from a remote subnet.Doing a port scan of the routers WAN or LAN address i cannot see any ports open at all...its as if firewall or NAT is still enabled somehow.

View 0 Replies View Related

Cisco :: 5508 - Unable To Access Controller Using Management Interface

Apr 3, 2013

I configure IP address on the management interface port 1 of 5508 controller when i connect it direct to my laptop i can't ping or access controller from my laptop even i connect through layer 2 switch still i can't not.
 
IP Address of management interface : 10.21.0.50
Laptop IP Address : 10.21.0,51

View 13 Replies View Related

Cisco Firewall :: ASA 5550 - Configuring Sub-interfaces On Management Interface

Nov 29, 2011

I am currently doing some research (for my employer) into creating multi-context sub-interfaces on a Transparent ASA 5550.
 
I have not been able to find any details on this subject which state it is or it is not possible. This will be used for Syslog logging.

View 1 Replies View Related

Cisco Firewall :: Verification Of Management Interface Usage On 5510

May 24, 2012

I seem to get conflicting information on using the Management port as a regular routed interface on the ASA5510..The management interface can be used for the traffic that passes through the firewall as well. The Security Plus License for the ASA 5510 is required in order to use the management0/0 port as a regular interface. With a base license on the 5510, the management0/0 port cannot be used as a regular interface.
 
I believe that I saw another post that mentioned it was part of the standard IOS if you had a later version.

View 2 Replies View Related

Cisco Firewall :: Bandwidth Management On ASA 5505?

Sep 30, 2012

I have 20 mbps internet link and I have ASA 5505 . I have to divide this bandwidth 10-10 mbps each for Voice and Data . So that both can work properly. because when I am using it for both on same interface, I am getting Voice disturbance..

View 1 Replies View Related

Cisco Firewall :: Bandwidth Management ASA 5505

Jul 24, 2012

i have 16MB internet speed, i want to give inside interface in my ASA only 2MB to use how can i assign it ?
 
ASA Version 8.2(5) !hostname ConcordeASAenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface

[Code].....

View 2 Replies View Related

Cisco Firewall :: Pass Management VLAN Traffic Through ASA 5510 In Transparent

Mar 10, 2013

We have a small cisco 1800 series workgroup router that seperates our network from the outside world.  The data coming into our network goes into the router on interface fa0/1 and comes out on interface fa0/0.  fa0/0 is split into 2 sub-interfaces (fa0/0.2 and 0/0.3).  These sub-interfaces correspond to a desktop and server vlan on our network.  The workgroup router is connected to a 3560G trunk port (we'll call it switch 1) and switch 1 connects to another 3560G (we'll call it switch 2). Recently I was asked to add another layer of security to our network by installing an ASA 5510 firewall and forcing certain types of traffic to authenticate using their domain credentials for our network.  The firewall was set up between the router and switch 1 in transparent, multi-context mode.  There are 2 security contexts, 1 for the desktop vlan and 1 for the server.  Both have the same security settings applied to them since we want the same behavior regardless of whether they are trying to access the servers or the workstations.

View 2 Replies View Related

Cisco WAN :: Switch L3 3750 - Bypassing Firewall With Network Management VLAN 20

Aug 22, 2011

I would like to push route for admin services (Vlan20) to bypass the firewall via an other connection (CSI to CSE). So my first choice was to create a route-map in (CSI) but I don't know how to do it. On my Firewall ASA, I don't have any Context License, that is why I would like to do it like this.
 
I have included some part of my initial configuration CSI and CSE and diagram.

CSI configuration (Switch L3 3750) {
interface GigabitEthernet1/0/1
description To ASA
no switchport
[Code]....

View 1 Replies View Related

Cisco Switches :: SRW224G4 - Cannot Access Web View Management Interface Through IP Address

Jul 12, 2012

I am the Systems Admin at LDM Media and am trying to get some support for one of the SRW224G4 managed switches we have in our rack. The issue is as follows:

Any endpoint connected to the switch is assigned an IP address in the range of 169.254.154.XXX regardless of the switches set IP range, the second issue is that I cannot access the web view management interface through the default IP address 192.168.1.254 (and I have tried to use the last IP in the range set by the router 169.254.154.254, to no avail)
 
How to regaining control of this supposedly smart switch?

View 3 Replies View Related

Cisco Firewall :: ASA 5510 High Drop Count On Management Interface

Sep 4, 2012

I have a 5510 FW in multi-context mode that is showing a high drop count on the Management interface in the Admin context.

View 1 Replies View Related

Cisco Firewall :: ASA5510 Static Routes For Management Interface Not Working

Mar 30, 2011

We have several pairs of ASA5510s in failover A/P mode, some running 8.3(2) and others running 8.4(1).
 
e0/0 = outside
e0/1 = inside
m0/0 = management
 
The problem we're having is we can't get anything to route out of the management interface unless we put in a static route at least to the subnet level. For example, we want syslog traffic to exit out m0/0 to our syslog server 10.71.211.79. Our 'gateway of last resort' points to the next hop out e0/0, and a second static route with a higher metric and a more distinct network space is for m0/0 as in:
 
route outside 0.0.0.0 0.0.0.0 192.168.49.129 1route management 10.72.0.0 255.255.0.0 10.72.232.94 10
 
This doesn't work, and ASDM loggin gives this error: ".....Routing failed to locate next hop for udp from NP Identity Ifc:10.72.232.89/514 to management:10.72.211.79/514"
 
If I put in a more granular subnet route, or a host route of the syslog server it works, such as:
 
route management 10.72.211.0 255.255.255.0 10.72.232.94 10   <------------- this works
 
route management 10.72.211.79 255.255.255.255 10.72.232.94 10   <------------- this works too
 
Why won't a static route for 10.71.0.0 255.255.0.0 work in this case?
 
We are going to have numerous hosts access and be sent messages though the management interface of these ASAs, and it would be very burdonsome to have to add a host, or even a subnet, route for every one. I've removed all static routes and tried to rely on EIGRP, but that doesn't work. I also had to put 'passive-interface management' under the EIGRP for this to work.
 
Here is the pertinant ASA config concerning syslog, routing, and interfaces:
 
interface Ethernet0/0 nameif outside security-level 0 ip address 192.168.49.140 255.255.255.128 standby 192.168.49.141 !interface Ethernet0/1 nameif inside security-level 100 ip address xxx.xxx.xxx.xxx 255.255.255.128 standby

[Code].....

View 3 Replies View Related

Cisco Firewall :: ASA 5510 / Management Interface Stopped Working After Upgrade?

Jun 24, 2012

After I have upgraded our ASA 5510 to 8.4.2 I have problem with the management interface.Our former firmware 8.2.3 had no problem using the management interface as a DMZ zone, but after we upgraded to 8.4.2 we can't make it work.The interface and the protocol is up, when I type: show interface.But when I ping the interface from a computer connectet to the interface, nothing happens.
Even the logging shows nothing.

View 7 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved