Cisco Infrastructure :: 4-port Serial HWIC-4T Is Compatible For 2801

Apr 23, 2012

Just want to ask if 4-port serial HWIC-4T is compatible for the Cisco 2801?We need additional HWIC for Fast Ethernet but the problem is we don't have already slot for it.We already have two HWIC-2T 2-port serial which is inserted at slot 1 and slot 3. We're planning to buy 4-port HWIC-4T so we can use the slot 3 for HWIC Fast Ethernet.if it's possible to have the 4-port serial HWIC-4T be inserted to Cisco 2801.

View 1 Replies


ADVERTISEMENT

Cisco Infrastructure :: Use HWIC-4ESW As No Switch Port?

Oct 4, 2012

Can We use Cisco HWIC-4ESW as no Switch Port.

View 5 Replies View Related

Cisco WAN :: 2801 - HWIC Not Showing After Upgrading IOS?

Jun 11, 2012

I have Cisco 2801 router with IP Base image, i have upgraded its image into advance Ip services for using IP SLA features but after upgradation HWIC card not showing in configuration.
 
When i recall IP base image then configuration show presence of HWIC card but with advance IP services HWIC card not showing.

View 8 Replies View Related

Cisco WAN :: HWIC-2CE1T1-PRI Not Supported On 2801 Router?

Jun 18, 2012

The HWIC-2CE1T1-PRI card isn't supported on a CISCO2801 router

View 7 Replies View Related

Cisco Switching/Routing :: Is HWIC-2T Compatible With 2800 Routers

Oct 17, 2012

Just need to verify if HWIC-2T is compatible with the Cisco2800 routers?

View 4 Replies View Related

Cisco Infrastructure :: Serial 4T Not Detected In 2621

Oct 21, 2004

I have a cisco router 2621 when i install the module cisco NM4T it is not detectetd. following are the outputs.i have tried IOS 12.2.15T15 & 12.3
 
booting up:
smart init is sizing iomem
ID            MEMORY_REQ                 TYPE
0000A2          0X00103980 C2600 Dual Fast Ethernet

[Code]......

View 4 Replies View Related

Cisco Infrastructure :: 750 - Serial Numbers And MAC Addresses

May 7, 2013

I am in the process of implementing 750 Cisco Access Points acros the business. I need to make a note of the serial numbers and Mac addresses for our inventory before I get these configured and sent out to their relavent destinations. The AP's have have arrived in boxes of 10 (75 boxes). The sticker on the box with the barcode is either covered with a postage sticker, ripped, or my scanner will not scan it becaise it is too small. There is a sticker with the serial bundle which is larger and therefore scanable. Is there a way that I can scan this and get the MAC address and serial number.

I know that this is not a technical question but I don't want too spend the next 3 weeks opening 75 boxes and removing each AP individually and recording it.

View 4 Replies View Related

Cisco Infrastructure :: 2950 - Determine The Serial Number On GBIC

Jun 27, 2004

Im trying to determine the serial number of Gbics already installed and running on a Catalyst 2950 switch. Is there a specific command to do so? There is a command on Catalyst 4506 that gives all info regarding the Gbic ("show idprom interface gi 1/1") Is there something equivalent for 2950?

View 4 Replies View Related

Cisco Infrastructure :: Connect Two Router With One HWIC-4ESW Card?

Sep 2, 2011

How Can I connect two router with one HWIC-4ESW card , I have Problem with this  because when I tried to do , I received the message I can´t  configure IP address on L2.  The idea is to connect two routers  with   /30.

View 2 Replies View Related

Cisco Infrastructure :: Is GLX Compatible With 3750G-24PS Switch

May 23, 2011

I am trying to buy a GLC-SX-MM SFP module via Fed Stock, and I keep getting a GLX-SX-MM. What is the difference between these two part numbers? I can't find it on the Cisco Web site and eve a search of Google comes up relatively fruitless! Is the GLX compatible with my 3750G-24PS switch?

View 2 Replies View Related

Cisco Infrastructure :: 1905 Compatible For Connecting USB Internet Dongle

Aug 7, 2012

I want to know if Cisco Router 1905 is compatible for connecting USB Internet dongle for VPN Tunnel configuration at USB port of same router. If Yes then how to open that port for config. Find the show tech logs of Cisco Router 1905 attached.

View 1 Replies View Related

Cisco Infrastructure :: NM-1Fe Fastethernet Module Not Compatible With 2 Series Routers600

Oct 13, 2012

I understand that the NM-1FE Fastethernet modules are not compatible with Cisco 2600 series routers, just the Ethernet 1-E module.  With that being said, are there ANY modules supported by the 2600, 2621 or 2621XM series routers that have fastethernet port(s) outside of the pricey NM-16ESW module?  I don't need a 16 port module!

View 3 Replies View Related

Cisco Infrastructure :: HWIC-2FE Fails To Pass Ping Packets Greater Than 449 In Slots 0 Or 1

Apr 9, 2013

When we install an HWIC-2FE card in slot 0 or slot 1 of a 3845, the interface fails to pass any ping packet greater in size than 449 bytes.  It works fine up until that limit is reached, but then fails completely on a larger size packet.  If we move to slot 3 or slot 4 on the 3845, the card works just fine!  I have looked through the cisco official bug tracker for HWIC-2FE, but could not find a similar symptom listed.  We're running advanced ip services 12.4(24)T7 code on the routers. Any software fix or if this is a platform problem with the 3800 series. 

View 3 Replies View Related

Cisco WAN :: 2600 Router - Way To Get Serial Port V35

Apr 11, 2006

How to know the serial0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?

View 4 Replies View Related

Cisco WAN :: How To Multicast RS-232 Serial Port Data

Sep 5, 2012

We want to multicast several serial ports over the WAN/LAN network.In few words what we need to do is transport is several serial ports, is like a RS-485 network but in this case via IP.I do some similar to transport 4E&M lines with great results but I don't know how to start to do the same but with the Serial ports.

View 1 Replies View Related

Cisco WAN :: 3845 - Configuring Serial Port In IOS 15.1(3)T?

Mar 16, 2011

I just installed a HWIC-2T in a Cis co 3845 running IOS 15.1(3) T  New build.The IOS self installed the port configuration including the command line "clock rate 2000000."  I can edit everything but that entry using the CLI.  When I enter the "no clock rate"  it will not take in the running conf.

View 2 Replies View Related

Serial Port Is Not Detecting The Fax Modem?

Apr 13, 2012

serial modem US robatics 5686G is not detected on windows server on serial port com1. i tried to restart the server . turn the modem on and off disable the com1 port reenable it again . update the firmware of modem on different workstation and connect it back to server ( couse it's working on another workstation so it's not the modem) i really don't know what to do is there a trick for this like in registry or somthing in mouse settings that mouse could actully detected on com1 and don't let the modem to show up on device manager? by the way modem cable is serial cable i tried to change the cable as well non of my ways works?

View 4 Replies View Related

Hp 8560p Elitebook - Integrated Serial Port

Apr 25, 2011

HP just released the 8560p elitebook- not a bad shake and it actually has an integrated Serial port.Any other notebooks that have integrated serial ports?- I know the T6x Thinkpads used to use a slimbay adapter thing. I just hate the Usb adapter, and bossman said I could get a new computer here pretty soon...

View 2 Replies View Related

Cisco WAN :: 2801 And Switch Trunk Port

Apr 20, 2012

1- Cisco Router
Eth0/0 : Ip address 192.168.1.1 /24   == connected my laptop of 192.168.1.2
 /1: Ip address : 192.168.2.1 /24   = connected cisco swith

2 - Cisco Switch
VLAN 2 Name : Sales : ip address 192.168.3. 1 = connected computer 192.168.3.2
VLAN 3  Name : Marketing : ip addres 192.168.4.1 = connected computer 192.168.4.2

So I want my laptop that connected the router Eth0/0 Interface should access both VLAN 2 and VLAN 3 computers

View 4 Replies View Related

Cisco WAN :: Two 9 Port HWIC-ESV In C2821 Not Working?

Feb 27, 2011

Based on the business requirement, I have installed one more 9 port FE Switch in addition to existing one, NM is discovered but when we connect PC or IP-Phone it is not working, current IOS is flash:c2800nm-advipservicesk9-mz.124-3h.bin  with 64MB Flash

View 5 Replies View Related

Cabling / Cards :: Connect To Cisco Console With / Without PC Serial Port?

Jan 5, 2012

I need to connect to the console port on a cisco firewall, an rj-45 connector. The cable is a rj-45 at one end and a serial on the other. My PC has no serial port and I am unable to use the provided cable to connect to the firewall appliance. Is there software that can allow serial over my PC's Ethernet? I really don't have time to order a serial card for my PC.

View 1 Replies View Related

Cisco :: Port 6050 Accepting Connections On 2801?

Dec 14, 2012

I have a 2801 with a very simple config that's accepting telnet connections on port 6050 from everywhere:

View 1 Replies View Related

Cisco WAN :: Configure 2801 With Multipoint Port Channel

Jan 5, 2012

Is it possible to configure a Cisco 2801 router with Multipoint Port Channeling? A service provider dropped a 4.5Mbps ( 3x T1s ) to one of our customers without any equipment. They assume the CPE responsible. If so, any links to documentation on this configuration. If not, what device will they need to buy from Cisco that can bundle these 3 T1s together then feed it into their router?

View 6 Replies View Related

Cisco WAN :: Port Adapter With Synchronous / Asynchronous Serial Ports For 7200

Jun 19, 2011

Is there a Port Adapter (PA) with Synchronous/Asynchronous Serial Ports, for Cisco 7200?

View 1 Replies View Related

Cisco WAN :: 1905 / Clarification On Txload And Rxload On Serial Port For Routers

Sep 21, 2012

I have a 1905 series cisco router, when I run "sh int" command it gives me following details -
 
MTU 1500 bytes, BW 1544 Kbit/sec, DLY 20000 usec,
     reliability 254/255, txload 7/255, rxload 151/255
  Encapsulation PPP, LCP Open
  Stopped: CDPCP
  Open: IPCP, loopback not set

[code]....
 
let me know the significance of txload and rxload.This router is used for MPLS connectivity.Link is working OK..but I'm not able to understand exactly what is the above txload and rxload signify.There is also one peculiar phenomena occuring, when my reliability goes down then rxload also goes down or might be vise versa.

View 2 Replies View Related

Cisco Switching/Routing :: 2950 Laptop Doesn't Have Serial Port

Feb 15, 2013

I have two 2950 Switches and am trying to connect via my laptop.  My laptop doesn't have a serial port so I am trying to connect through the ethernet port, with a straight through cable and on the end as it goes into the console port I have bought a cisco console rollover adapter.When I turn on terra term I get nothing...just a black screen and it disconnects.

View 6 Replies View Related

Cisco Switching/Routing :: 2801 Secondary IP / Port Forwarding?

Mar 26, 2012

I have the above firewall which is working as it should but I have came across an issue with a recent upgrade to Microsoft Exchange 2007 and Outlook 2010 Autodiscovery due to the way the port forwarding has been configured for Outlook Web Access (OWA) on the router.
 
The router is forwarding OWA requests to the exchange server on port 8080 and the default website in IIS on the Exchange Server under which OWA sits and unfortunately Autodiscovery has been set with an SSL port of 8080. I think the reason for this is that we have an RDP server and the router is forwarding all port 443 requests to this server. Due to this Outlook clients cannot connect to Exchange through autodiscovery and cannot therefore get FREE/BUSY and a few other things.
 
I have 5 public IP addresses and only use two at the moment, one on the ADSL router and one on this firewall. I have no spare interfaces on either the router or the ADSL router.
 
My question is, is it possible to have a secondary ip address set on the public facing interface and set different rules for this IP which would allow me to forward requests on that IP to a different server?
  
Cisco IOS Software, 2801 Software (C2801-ADVSECURITYK9-M), Version 12.4(16b), RELEASE SOFTWARE (fc3)
 
Building configuration...
 
Current configuration : 4778 bytes
!
version 12.4
service timestamps debug datetime msec

[Code].....

View 1 Replies View Related

Cisco WAN :: Apply MQC On 4 Port HWIC-4ESW - 3845 Router?

Mar 24, 2011

I have 3845 Router with HWIC-4ESW & I am trying to apply MQC on SVI interface but I keep getting configuration Error!-RTR(config-if)#service-policy output XYZ_WAN_QOS Configuration failed I believe that HWIC-4ESW is Layer 2 port & you can not apply Module Qos on SVI interface. I am exploring other option.
 
I have following link for 1 OR 2 Port Fast Ethernet port but not sure whether this will support what I am looking for.[URL] Aslo I have HWIC-1GE-SFP card on Same router where MQC works fine .interface GigabitEthernet0/1 description METRO-E  duplex auto speed auto media-type rj45 service-policy output Metro-E?

View 1 Replies View Related

Linksys Wireless Router :: Serial Connector Adapter / Cable For WAN RJ-45 Port?

Aug 21, 2009

On the WAN port, there are 4 pins that are traced to the internal serial traces.  Where can we get the cable that will fit into the WAN RJ-45 port and have a serial connector on the back end.  It may be called a Cisco Debug Adapter, but we haven't been able to find?

View 9 Replies View Related

Windows 7 - Connect Virtual Machine To Host Via IEEE1394 / USB Or Serial Port

May 15, 2013

I have a host machine (Laptop, Win 7 Home Premium x64) running Windows 7 Ultimate x64 on VMWare Workstation 9. I've got this system set up for UMDF driver development, because I need a target machine to debug drivers on. However, because I'm developing drivers for Win 7 (x86 and x64), I cannot connect to the virtual machine on via a simple network connection. Connection methods are outlined here.

I have tried a few different pieces of software (mostly Eltima software), and have Google'd every combination of phrases that I can think of. I can't find any information on this anywhere. I don't just need to share data between the machines, I need a more "physical" connection.

Does any know how to do this, or if there's another (preferably more simple) way of doing it?

View 1 Replies View Related

Cisco Switching/Routing :: 2801 Router Console Port Not Working?

Feb 13, 2013

I  have issue with Cisco Router 2801's Console Port. My student was doing a  lab and he said during configuration, Console Port stopped responding.  He was in middle of configuration, so now at present, only telnet is  able to login on "R2>" user mode, enable password is not set, so  getting "R2>en % No password set R2>" I have tried  different terminal software but no output from Console Port, changed the  Console Cables, replace with working console cables, change speed  (baud) settings. Also tried to connect same console with "AUX" port and  got same error mentioned above. AUX Port responds but I am not able to  change mode (R2#) because of incomplete running-config. it seems "Console Port" is physically  damaged.

View 4 Replies View Related

Dell :: Aio 924 Compatible With D-link Share Port?

Feb 20, 2012

says everything is good but when I go to print...laptop can't find printer?

View 1 Replies View Related

Cisco Infrastructure :: Two WS-X6148 With Even / Odd Port Failure?

Feb 8, 2012

I have two WS-X6148-45AF linecards here that have been out of use for quite some time. Upon inserting them in one of our 6509-E's I noticed that both had "Minor Error"s on their module diagnostics. 
 
I would have just assumed that the cards were dead and requested replacements, but both cards have the *exact* same diagnostic errors, which only seem to effect every-other port. That's too much of a coincidence for me, so I figured I'd ask on the forums and see if I'm just missing something obvious before I assume the worst. Are these cards both somehow damaged in the exact same way? Or is there some config/compatibility issue that I haven't heard of?
 
relevant diagnostic output from one of the cards (Both outputs the same, no use posting twice) is below: 
 
Router#show diagnostic result module 4
Current bootup diagnostic level: minimal
Module 4: 48-port 10/100 mb RJ45  SerialNo : SAL11391VUY

[Code].....

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved