Cisco :: LMS 4.1 Reporting For VLAN Information
Mar 6, 2012
I'm currently running Cisco LMS 4.1. I need to see if there is a way in the LMS, either through the menu or via a report, that can give me the V LAN numbers, the description, the IP address, the Interface (SVI) the v LAN is on and the route it takes.
I've searched near and far and haven't come up with anything yet.
View 3 Replies
ADVERTISEMENT
Nov 27, 2011
We have a pair of 6509 working in a VSS configuration (IOS 12.2(33)SX5). The 6509s connect to a pair of ASAs (7.2 code) running in an Active/Standby setup. These ASAs in turn connect to routers going to remote sites. I have configured Netflow on the following VLANS,
VLAN 10 - Servers Vlan
VLAN 9 - Transit/ASA VLAN (connects ASAs to 6509s). All traffic originating from any VLAN on the 6509 crosses this VLAN in order to reach remote sites and vice versa
I configured the netflow source VLAN 11 although I am not collecing any netflow from it.Although I have been getting lots of Netflow info, I noticed that netflow for traffic originating from any user VLAN on the 6509s going to any remote site via TRANSIT/ASA VLAN(9) does not get reported, I even tested with 4 GB traffic but no result. Only reverse traffic (i.e. from remote site to user VLAN) is reported as it traverses the Transit VLAN (9).
I read somewhere that egress netflow is not supported in 6500, but isnt traffic originating from a user vlan to a remote site via the transit VLAN (9) considered ingress with respect to the transit VLAN (9)? I would like to know whether bidirectional Netflow is supported on 6500 VLANS. I have mimimum control on routers beyond the ASAs, and since these ASAs run 7.2 code netflow is not supported, and Monitoring this Transit Vlan gives me extremely useful info.
I do get netflow biderectional traffic from the Server Vlan 10, but I think it is correlated by the netflow collector from vlans 9 and 10. [code]
View 9 Replies
View Related
Jan 29, 2013
I have a switch cisco c 3750 that has vlan information, how to remove vlan information.
View 1 Replies
View Related
Aug 10, 2012
I have 2 SG300 switches and all I want is to propagate VLAN info from one to other. I do not have computers with GVRP compliant NICs, so I dont want that auto registeration functionality on access ports. I want VLAN prop via trunks and switchport mode access on access ports just like VTP. I have read on cisco docs that this functionality is provided with GVRP Mode fixed, but there are only 2 modes that I can see on SG300 are Normal and Forbidden. Trunk configured correctly, gvrp is enabled globally and on port, ports are up and functional, tried different combinations of checking and unchecking boxes of dynmic vlan creation and enable registeration on both ends but no joy. When I create a vlan from one, it doesnt propogate to other.
View 1 Replies
View Related
Oct 2, 2012
I have 2 NEXUS switches in VPC. When I create/delete a VLAN gets updated in the same switch, but the VLAN information does not get propagated to the neighboring switch. Revision number remains the same even if I modify the VLAN. Had also tried changing the VTP status to transparent mode & reverting it to client mode but no luck.Have double confirmed on the VTP domain names & password. However the same setup in different location which works perfectly fine.
View 1 Replies
View Related
Jan 31, 2011
Is there any way to get reports on voice utilisation on WAN links so that CAC settings can be proactively managed for each location on our CUCM cluster? Our service provider is advising that this is not possible which means that we rely on customer/staff complaints to recognise where CAC thresholds are being reached. Our preference is to be able to run traffic reports (or the Cisco equivalent) as could be done on our previous (traditional) telephony network and provide additional capacity if and when required BEFORE congestion is reached, thus minimising customer/staff impact.
View 1 Replies
View Related
Sep 27, 2011
Runing the report, "CleanAir > Worst Interferers" and I get this error
The specified criteria did not match any data for the report. Make sure that the following background tasks are running: 1. Interferers
I know there is data that should match up because I can see it on the individual controllers. I checked the background task Interferers and it appears to be working as well but just to make sure I forced the "Execute Now" command but the report still failed.
View 4 Replies
View Related
Jul 31, 2011
WCS is reporting few AP's are not associated with it. While troubleshooting, AP conneceted switch interface shows UP/UP and show power inline output gives IEEE PD instead of AIR-LAP1131AG-E-K, after doing a shut/no shut on AP connected interface. Later after sometime AP comes up.
View 5 Replies
View Related
Sep 26, 2011
we are running WCS 7.0.164.3 and wonder whether is there any reporting option availabel that can give us daily report on Top 50 or Top 100 APs by client count.
I know that I can look at the client tab under WCS home page and see the top 5 APs by client count on real time.In our environment we have around 700 APs and would like to know by having this kind of report which APs are mostly hit ?
View 5 Replies
View Related
Jan 31, 2011
I have not managed to get the Monitoring to work on the ACS 5.1. This is an eval version. Advanced monitoring and reporting is installed on the ACS. This is my configuration on the Cisco Router
aaa accounting exec default start-stop group tacacs+aaa accounting commands 0 default start-stop group tacacs+aaa accounting commands 1 default start-stop group tacacs+aaa accounting commands 15 default start-stop group tacacs+aaa accounting connection default start-stop group tacacs+
logging origin-id iplogging facility sysloglogging source-interface GigabitEthernet1/1logging host 1.1.1.1 transport udp port 20514
logging monitor informational
epm logging
On the ACS, when I open the dashboard --> ACS health -> I get Status not available.Global Instance under Logging Categories been configured for local logging?
View 4 Replies
View Related
Jan 8, 2011
I just upgraded yesterday to the DIR-655 (ver B1, F/W Ver 2.00NA), and suddenly my sons Xbox 360 complains that the NAT is set to moderate. I'm not really sure what this means, but I've never seen it before and it wasn't an issue with my old router. It pertains to the DIR-655? I did some quick google searches and I've seen lots of different 'solutions' to this issue, but none of them seem to agree with each other and I'd rather not spend and entire afternoon trying one after another given that this router kills my internet connection for a full 20 seconds every single time I make any change.
View 4 Replies
View Related
Apr 27, 2012
We have discovered Nortel/HP C-GbE2 switches on our network are sending spanning tree Topology Change Notifications (TCN). The HP switches only have servers connected and no other switches leading to any other network segment so we are not clear why the switches are sending spanning tree TCNs every second. We do not have a support contract. Can anyone on the Cisco side speak to what's referenced on page 5-6 of the attached document? I found the attached document which talks about diabling spanning-tree (page 5-6) in Cisco environment but wanted to consult with an expert before proceding. Document (Configuring Nortel Gigabit Ethernet Switch Modules for IBM BladeCenter in a Cisco Environment Solution Brief.
View 0 Replies
View Related
Dec 23, 2011
I noticed one awkward thing with the latest 1.0.3.5 firmware for the Cisco Small Business RV220W router, with previous firmwares there has always been reported 128mb of system memory (RAM) under the router dashboard. And several "teardowns" of this router has confirmed it to have 128mb of memory on the router board.
Does that mean the latest 1.0.3.5 has an odd visual bug, or has the RV220W gotten it's memory sliced in half with this firmware release?
View 4 Replies
View Related
Jun 12, 2013
Is there any way to determine how much bandwith users on a particular WLAN (Guest) are using on the 5508 or by any other means?
View 9 Replies
View Related
May 16, 2011
I'd like to know if there is a way to exclude passed authentications for a specific username from reporting in the Authentications-TACACS and Authentications-RADIUS reports?
We have a few usernames that are used in scheduled jobs. We only need to know when they fail authentication, so we don't need to fill up the reports with every passed authentication from these accounts. Can this be done?
View 1 Replies
View Related
Apr 23, 2013
I'm using ASA 5510 and I wondered if we can configure reporting to know the traffic on each interface,the attacks,the vpn connection during a period ( 1 week or 1 month). For the moment, we can see these logs only in 'real time' .
View 1 Replies
View Related
Jan 1, 2013
We have 2 ASA 5505 located in head office (173.212.xxx.xxx) and remote site (50.34.xxx.xxx) and site-to-site VPN has been established between them.everything is fine but the ASA in head office keeps reporting below 402120 syslog message.
4 Jan 02 2013 12:30:34 402120 50.34.xxx.xxx 173.212.xxx.xxxIPSEC: Received an ESP packet (SPI= 0x384E1C57, sequence number= 0x2AE77) from 50.34.xxx.xxx(user= ) to 173.212.xxx.xxx that failed authentication.
Even though, VPN tunnel is not dropped.
View 2 Replies
View Related
Jan 10, 2013
1) How do you manage your inventory of network equipment from the time you receive a product into inventory to the time you decommission it?
2) How do you make aware the people who manage your network monitoring/reporting software that a device has been added/removed from the field?
2a) How do you notify the people who manage your network monitoring/reporting software of what is to be monitored on a new device in the field? Of a new interface that has been added/removed on an existing device?
2b) How quickly do you notify for 2/2a? i.e. minutes, hours, days, etc.
3) What types of interfaces and resources do you monitor on a network device?
View 3 Replies
View Related
Mar 20, 2011
I have just gotten a new touch phone that has wifi. and i wanna use it through my dlink dir-825 router. My phone is the nexus s with 2.3 andriod OS.The problem is that my phone can see the 2.4 ghz connection it just keeps reporting "deactivated" i did acess other wifi and used the internet over a router. So i know the phone works.
So my question is: 1. Can i make my router ONLY be in 2.4ghz mode, if so, can you link or explain it?
View 7 Replies
View Related
Mar 26, 2012
I am configuring new ACS 1121 appliance with version 5.3 and wanted to know how to configure Remote Database settings in ACS5.3 Is that necessary to configure that option ?
Also one more thing I can see that ACS 5.3 generates lots of logs is there any solution to reduce such logs. It seems many unuseful logs which are system related are getting logged into device which might no be good for memory requirements of device.
View 6 Replies
View Related
Jun 20, 2011
I get a lot of information via RME or SNMP but not the RAM Information.
View 1 Replies
View Related
Nov 21, 2012
Looking for the loading information for Cisco ACS 5.4 running on a VM. After user and device authentication figures.
View 1 Replies
View Related
Apr 2, 2013
Its more for information purposes. I am trying to compile some information together to get a better understanding of them so anything generic would do. Such as what it looks for in the traffic to block attacks, negative impacts of performance and a couple of top products I could have a browse of and so on.
View 1 Replies
View Related
Oct 1, 2012
I am having problems trying to connect to my wi-fi. I first noticed that I had problems connecting to some types of unsecured wi-fi connections when I was "borrowing" from my neighbour while I waited for telus to install my internet. My two roommates would have no problem surfing but my computer was unable to get any connection to the internet (i could see the connections but never load a page)
Once telus came and installed the internet I was able to get a "fair" connection to the router and surf with decent speeds. About a week after I first started using the internet, my computer started being unable to connect the router. It seems that everything is getting worse and worse. It started by me having to restart the adapter a couple of times to make it work, to me having to delete the network profile and then redo it, to me only being able to connect by using the WPS.
And now my computer can't even get the information from the router through WPS! I would start to point the finger at telus, but every one of my roommates has no problems connecting to the internet, and it's not a range issue (i'm typing this up with my laptop while sitting beside my desktop).
View 11 Replies
View Related
Jan 3, 2013
I am in need of some information regarding licesnes on the ASA 5505.I have a client who is connecting their main office to a DR site via a site-to-site VPN. I understand that the standard license for the ASA 5505 is for 10 clients.Does the site-to-site connection consume one of these licenses?Does each endpoint communicating over the site-to-site VPN consume one license also?For example, if I have the site-to-site VPN and 10 servers on each side, would that mean that I need 21 licenses; 1 for the VPN and 20 for each server on each side?
View 4 Replies
View Related
Jan 29, 2011
We are looking at buying an ASR1001 but I'm confused by the Licenses and I've struggled to find the information in the cisco data sheets. The router will need to run IPSEC on gre tunnels and I figure that I need the IPSEC license (FLSASR1-IPSEC) do I also require the Advanced IP Services license? or is all that is required the IPSEC license? Is there some sort of list that shows the feature set of each license, they cost the same amount so I'm not sure which license fits what we require best or if we need both.
View 1 Replies
View Related
May 22, 2011
I´m looking for a firewall for my company and am reading about both Cisco ASA 5505 with Security Plus bundle and Cisco ASA 5510 with Security Plus bundle and I have a few questions.This is the document i´m getting my information from.URL,It states the following:Cisco ASA 5505 Security Plus bundle,Includes Cisco ASA 5505, unlimited users, 8-port Fast Ethernet switch, stateful firewall, 25 IPsec VPN peers, 2 SSL VPN peers, stateless Active/Standby high availability, dual ISP support, DMZ support, 3DES/AES license, and 1 expansion slot.
View 5 Replies
View Related
Jan 12, 2011
Basically I am trying to do a bit of a clean up at work and replacing two dlink (home style) ADSL modems with a single Cisco 2901 router with 2 ADSL HWICs. On top of this I want to isolate the 2 connections from each other, that is I don't want to use them as fail-over or anything just as 2 seperate connections. To do this I am using VRF tunnels.So far I have been successful in the global config of the switch and everything works. And when I put the lan, atm and dialer interface into my VRF it connects up all fine.My issue that I am having is that DNS (which is being pulled from the ISP via ppp ipcp dns) seems to just populate the global dns view, not the view I created for the VRF. This results in DNS queries not being able to be resolved but all other traffic is fine (i.e. I can ping and access anything on the net, I just can't resolve names).
If I have 2 ADSL connections, on two VRF tunnels, how can I seperate their DNS information for each connection/VRF tunnel? especially if that information is different as they overwrite the global DNS config each time they connect.... I could (and have successfully tested) statically assigning DNS servers to each DNS view but I would rather rely on each ISP sending their DNS servers as opposed to me hard coding them.
View 2 Replies
View Related
Mar 21, 2011
I tried to find the EOL or EOS of the IOS A2(1.6a) of our ACE10-6500-K9 module.what to do ?
View 1 Replies
View Related
Aug 26, 2012
We have 4 x 4xxx WLCs setup in our Core. I just created an AP group in one of WLC and in theory I should see that AP group in the other 3 x WLCs
For some reason, I do not see that AP group appear in other 3 x WLCs. Very much appreciated if someone could point me to the right information or trouble shooting steps.
View 5 Replies
View Related
Jun 14, 2011
i would like to get information from my ASA5520 using SNMP V2c such as :
-xtable entries
-ARP cache table
does it's possible or not ..
View 2 Replies
View Related
Jan 1, 2012
I am looking into buying an ASA5505 but I would like to know if it is going to work in my setup. I have an Internet connection and 2 seperate networks. I know that the ASA5505 has 8 ports and I would like to know if I can assign each port to a different network zone? I dont want to use VLAN but physical networks. I know it is possible with ASA5510 and above but I want to make sure I can do the same with a ASA5505 (Without the security upgrade). I want to get an ASA5505 unlimited users.
So an Internet connection (with multiple IPs), 2 seperate networks, I want to filter traffic between all 3 and route between them also.
View 2 Replies
View Related
Mar 30, 2011
request for registration - wont submit - nothing happaens
View 1 Replies
View Related