Cisco :: Mapping File Structure From LMS3.2.1 To LMS4.2
Oct 9, 2012
in LMS3.2.1 we have NMSRoot/log/syslog.log where syslogs are being logged actively from managed devices. i couldn't find the same in LMS4.2. I am configuring LMS4.2 from scratch and in the hope of making the trasition from old LMS3.2.1 to LMS 4.2, I am planning assigning the old LMSs IP to the new one. basically changing the IP address of LMS4.2.
View 10 Replies
ADVERTISEMENT
Oct 4, 2012
i tried to restore backup from LMS3.2.1(windows) to LMS4.2 virtual appliance. once the back up is completed, the home page takes forever to load. i opened TAC case, and the only way out seems to be configuring from scratch after importing the devices. i, imported the devices and this didn't cause any problem. But, making the configuration from scratch is something i would like to avoid if possible.
View 1 Replies
View Related
Aug 23, 2011
in RME->Software Management-> Software Distribution -> By Devices [advanced], what is the file format we should have here, when we try to deploy many IOS images at once?
View 1 Replies
View Related
Jul 14, 2011
We know that every node in the network uses its routing table to forward the packets towards their destination. I have a doubt that which data structure used to implement these routing protocols.
View 6 Replies
View Related
Feb 22, 2011
Which data structure used to preparation of a routing table.
View 6 Replies
View Related
Jun 21, 2012
We are installing a set of 5508 controllers at one site in Tennessee. At another divisional site we have another controller that covers that division.
Both sites utilize the same DNS structure and would like to use the DNS entry CISCO- CAPWAP- CONTROLLER entry for bringing new AP onto the controllers at their sites, how would we go about configuring this?
View 6 Replies
View Related
Nov 3, 2011
I previously put this is the 'Video over IP' discussions group, which is not getting any response.I have a 6509 and need to configure QoS on gig line cards that have 1P3Q8T queue structure. I've already got the mls qos configured, and have the correct class maps built for Voice, Video, and Signalling.(I'm not doing autoqos). I have only four classes; voice, video, signalling, and default (best effort).I need to configure the commands on the individual gig ports for the appropriate bandwidths as shown below:
1. 300 VoIP G711 calls x 100kbs/call = 30mbs of priority queue DSCP = EF (46) CoS = 5
2. 150 Video conference calls x 1.5mbs/call = 225mbs DSCP = CS4 (32) CoS = 4
3. 450 Signalling x 13kps/call = 5.8mbs (round to 6mbs) DSCP = CS3 (24) CoS = 3
4. Default class is not marked DSCP & CoS = 0
View 1 Replies
View Related
Jan 18, 2012
Got following problem with an LMS server that is installed without DNS server in the network, because this customer doesnt own and doesnt need any.
CS,CM,CV is working and contains devices, but RME (cannot connect to db) and DFM (TIS URN found) not. pdshow and dbRestoreOrig.pl after calling, hangs for ever.
To loose no further time with troubleshooting, I want to reinstall LMS from the scratch.
But I dont want to setup an DNS server just for resolving the only IP-Adresse from LMS server for self purpose only. Do I need an entry in driversetchosts for LMS server itself?
<IP> <Name> <Name>.<Fake-and-complete-unimportend-domin>
Do I need a fake-Domain? or can Domain be empty?
OS=Win2008,R1,SP1 as Standaloneserver (WORKGROUP)
View 2 Replies
View Related
Jul 1, 2012
create a scheduled task in LMS. In this task I would like to regularly check time on all network devices in LMS and generate a rapport about this that would be sent to e-mail. All network devices have the same NTP server. How can I create this task? LMS version is 3.2 SP1.
View 4 Replies
View Related
Feb 12, 2012
I want to forward syslog messages that I receive in my Cisco Works server to another server,what is the best way to accomplish this. I'm running LMS3.2 on Solaris 10.
View 3 Replies
View Related
Jul 20, 2011
On our CiscoWorks 2000 installation, running on Solaris with LMS3.2 and RME4.3.1, we noticed a few weeks ago, that the job "Inventory Collection" needs more and more time to finish. At the moment the job execution time is as high as 8 hours, compared to 3 hours before. When we look at the network traffic during job execution, we see after the collection phase (~3h) several hours with no traffic together with a very high CPU load. I mean to remember that this job used to complete around 15 minutes after data collection phase. Restarting the application and rebooting the system didn't work.When we look in to the IC_Server.log, we find devices with a completion time of over 20'000 seconds. Increasing from day to day. [code]
Affected devices are Cisco Nexus 5548P. We tried to delete/add these devices. That works for a few days, then the runtime starts to increase again.
Are we hitting a bug? And is it possible, as a workaround, to exclude devices from only the Inventory Collection?
View 3 Replies
View Related
Mar 24, 2012
I noticed that I cannot remotely check the Topology Services in Ciscoworks LMS 3.2. I have attached a screenshot of the error for reference. When I access Topology Services on the server itself, everything works well.
View 5 Replies
View Related
Jul 18, 2012
I have added 2900 series devices in LMS3.2.1 but same are showing "unknown"device Type in a report generated from common services DC R device List.
Both are snip enabled and responding too. What is the reason behind unknown device type so those are not reflecting in any module.
36.N007010101CRRUNKNOWN37.N007010103CRRCisco 2921 Integrated Services Router38.N007010201ASRUNKNOWN
View 7 Replies
View Related
Jun 1, 2010
i've the following problem. Check device credential verification job shows "Error performing SNMP operation" for a cisco 3750 configured with snmpv3.On the switch i can see that the lms can access the switch via snmpv3. Also cisco view works fine. Bug CSCsm89609 describe the problem but it should be fixed in RME 4.3. We are running 4.3.1.
View 9 Replies
View Related
Nov 6, 2012
Cant find the speeking result/cause of 4 and 1 in the example below, that are defined as enums in the MIBs normaly. Where can I access the result of "snmptranslate -M<MIB-dirs> -m ALL -Td <ps-status/test-oid>" if this is implemented in LMS overall? What are the OIDs from Cisco's ps-status/test, if the translation of MIB-enums is not implented?
Event_Description
StateNotNormalDevice IP
x.y.z.1Device Type
Switches and HubsFault Last Updated At
06-Nov-2012 16:12:49Component
[code]....
View 2 Replies
View Related
Oct 19, 2010
With lms 3.2 during installation we can choose what to install i.e. not install DFM or IPM.
How can we do this in the new release 4.0 of the LMS bundle. I saw no options for it during installation of the new server.
View 3 Replies
View Related
Aug 29, 2011
Cisco release the Cisco Prime LMS 4.1 on Aug. 2011. I download the lms4.1 from cisco and install it, but the lms4.1's evaluation license expire date is Oct. 28 2009. So my license already expired after I install the LMS4.1.
View 1 Replies
View Related
Apr 16, 2013
I would like to upgrade LMS4.2 to PI1.2. According to Cisco this is a minor upgrade (requires the SAS code) and can be downloaded from the Cisco portal for free. My question: Can I still reuse the license and the B2B cisco support I use for my LMS4.2 ?
I will also upgrade WCS7.0.x to PI1.2. Will there finally be 1 server running 1 merged software, or will there be 2 servers one for WCS >> PI and one for LMS >> PI ?
View 1 Replies
View Related
Nov 22, 2012
We migrated to LMS4.2 and i created new credential set and set it as the default. However, the new cdredential set applies only to newly added devices no to the migrated devices. for example when i run device credential verfication for a migrated device, the username used my LMS is "cwuser" as opposed to the one i created with the new credential sets. how can i make this new credentila set be applicable to all devices?
View 3 Replies
View Related
Nov 22, 2012
In our organisation we have multiple Nexus 5000 switches, which Cisco LMS 4.2.2 cannot get the running-config and startup-config from with the Archive Management process. When it does try to get them, I get a error as follows:
*** Device Details for SF-DERA-01 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,SCP
[Code].....
View 17 Replies
View Related
Nov 10, 2011
I reinstalled CiscoWorks LMS (Windows 2008 R2) updated th LMS with all availible devicepackages and imported all devices with a xml bulk import of the former installation. Now I am frustrated.... because after the reinstallation LMS has problems collecting the inventory data.The inventory collection for one local device (Cisco WS-C3560-8PC-S) starts and nevers stops.... I have to stop the ICserver to stop the inventory collection.
I have only 4 of nearly 1800 devices where it was possible to collect the inventory information.All the rest is supposed to unreacheable...Reports> Inventory>Management Status>Unreachable Devices.But if I take one of the devices which is reported to be unreacheable and do a device diagnostic (Monitor> Troubleshooting Tools> Troubleshooting Workflows) says it is reacheable...
The inventory does not appear in the "Collector Status"?
View 4 Replies
View Related
Dec 19, 2012
My cisco works LMS3.2 is not showing recent configuration of my Cisco devices. also it dont show any change report on last 24 hours or even if i select x number of day, looks like its not saving any changes made on devices.
today i logged in and cisco ASA was showing this in status as well Configuration Last Archived Time May 03 2012 11:27:46 EDT on checking i could see it is same date when cisco ASA was added in cisco works. do i need to click some where for auto update configuration changes and latest confoguration in cisco works setting?
View 1 Replies
View Related
Nov 7, 2011
I have a very special usecase with migrating devices from LMSv2.6 to v4.1 using DCR bulk import that was maintained manualy, not by discovering.The special thing is each device has its own SNMP-community and its about 1500 devices.RME discovery works fine, but I get the devices not discovered by DCR (CSDiscovery), because I need a minimal DCR discovery configration containing Seed and SNMP-settings. So I activated DCR as seed, but cant skip SNMP settings without an entry. But in this case I would need 1500 SNMP-lines that would be very unhandy. is in CSDiscovery-Settings a possibility to can leave SNMP settings untouched so it takes the credentials from the DCR, to can start DCR discovery?
View 6 Replies
View Related
Apr 22, 2013
I am having a strange issue deploying universalk9-150-2.SE2 to our 2960S. All the switches are stand alones.LMS gives an error when asking to upgrade the image but the fact is that the new software wents through - if I manually reload the switch everything is fine.why is RME showing an error if the new image seems to have been deployed?
View 23 Replies
View Related
Apr 6, 2013
Who can give me a SNMPv3 configuration template.I tried many times has been a problem
View 5 Replies
View Related
Dec 4, 2012
I have installed Cisco Prime Infrastructure 1.2 separately from LMS4.2. LMS4.2 is in production. I just want to run PI1.2 in parallel with LMS4.2 before migrating to PI1.2. Currently I have LifeCycle permanent license. Why don't I have the assurance lfeature set license. it is running in evaluation mode.
View 1 Replies
View Related
May 9, 2012
This is a WS-C4510R+E with a Sup 7-E running 03.02.02.SG enterprise.
I increased SNMP timeout to 10 seconds to no avail.
View 5 Replies
View Related
Apr 3, 2013
I’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other.
- I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit.
- So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
View 3 Replies
View Related
Jul 26, 2011
I am working on a Drupal site which is on a virtual server (the way it's been explained to me). I've been told I need to work with it through webdev. So I can copy a file off the server and onto my local machine. I make my edits and then try to upload it to the server. I get locked out with the message: Error 0x80070021: The process cannot access the file because another process has locked a portion of the file. I have tried shutting down my code editor, opening and closing the connection, tried different methods of reaching the server (Cyberduck and through Window's map network feature) to no avail. What can I do?
View 1 Replies
View Related
Jul 25, 2012
we have ACS 5.3 and 1042 AP. So we need to authenticate client based on user certificate, and after that to put the client in specific VLAN based on membership in Active Directory group.
Is it possible to do that? We can not solve the problem of identity store, once the user is authenticated based on regular certificate, we need to authorize the same user based on the specific attribute from AD.
View 1 Replies
View Related
Jun 22, 2011
Cisco 891 does Static IP mapping and where I can get instructions how to use Static IP Mapping?Is the Static IP Mapping done throught CLI or through the CCP?
View 5 Replies
View Related
Apr 7, 2011
We have ACS 4.2 and has been integrated with AD. Now, a new user group has been added in AD but we are not able to see that new AD group in ACS to do the mapping. We have refreshed the sgent in ACS and also have restarted the ACS agent in AD. But still we rae not able to fetch the new AD group in ACS in group mapping.any way to fetch the new group in ACS from AD.
View 1 Replies
View Related
Apr 5, 2012
Is it possible to Map a Network Drive over a VPN?Users in my company connect to a remote site using VPN (PPTP) and i am wondering, can i map a drive to the PC i am on from the remote network while connected to VPN?
View 10 Replies
View Related