Cisco :: NAM2320 Does It Support Transceiver 1G
Apr 18, 2013NAM2320 has two 10 Gigabit Ethernet mornitoring interface.Does it support 1G transceiver(SFP) like GLC-SX-MMD=?Or it only can support SFP+
View 2 RepliesNAM2320 has two 10 Gigabit Ethernet mornitoring interface.Does it support 1G transceiver(SFP) like GLC-SX-MMD=?Or it only can support SFP+
View 2 RepliesI will like to know if I can replace a 1gi fiber transceiver for a 10 Gi transceiver, without any changes on the switch config.the switch is a 3750G.
View 4 Replies View RelatedI have WS-C3750X-24T-S switch with C3KX-NM-1G and now i want to put a transceiver GLC-EX-SMD= in the switch SFP port, is this GLC-EX-SMD= compatable with that switch ?. i thoroughly check the product datasheet and compatible chart but their i don't have seen ?
View 1 Replies View RelatedThere're more than twenty 6509VE running in the network. All of them has got 1GE or 10GE SFP / GBIC.However, when I tried "show int trans" in some of them, there's nothing shown:
Router_A#sh int transceiv
No transceiver present
Router_A#sh inv
Router_A#sh int status | i connected
Gi1/1 connected 304 full 1000 1000BaseSX
Gi1/2 To WLC5508 connected trunk full 1000 1000BaseSX
Gi1/3 To WLC5508 connected trunk full 1000 1000BaseSX
[code]....
I purchased a couple of used Cisco Routers and Switches and the guy gave me a bag with some cabling and one of these little guys were inside:
I have seen them plugged in before on images of peoples labs, but what are they used for? Why would I want to use this?
I am looking for optical transceivers that are compatible with the Cisco 5509 switch. Preferably 1G.
View 3 Replies View RelatedWe have C7206VXR NPE-G2 platform with transceiver which support DOM.Could we monitor DOM tx/rx level statistic through snmp for 7206 platform?In CLI result of command "sh interf GigabitEthernet0/1 transceiver" give some information.We tried search for some MIB In "MIB locator" on cisco.com.
View 2 Replies View RelatedWe are looking to purchase some addidtional 48 port swithches for our network. Currently we have the following swtiches setup
2 of 3750 POE-24 (These two are stacked and have our servers plugged into them). Currently no SFP modules.
3 of 3560 POE-24 (These each have two 1000BASE-T SFP modules in them, with UTP connecting back to the 3750 switches above)
We are looking to get 2 of 48 port C2960S-48TS-L switches with two 1000BASE-T SFP modules in each that then will also connect back to the 3750 switches.
I had a few of question about this:
Will the cisco lite version (rather than the more expensive cisco base software) support the 1000BASE-T SFP modules?
The 1000BASE-T SFP modules, are they auto-config? Have you the link for commands we can use, if required?
We don't have budget for stack modules, apart from that would you recommend we change anything with the new setup?
Does the X2-10GB-T copper transceiver is supported on the WS-X45-SUP6L supervisor?
View 1 Replies View RelatedI have the follow error in a SW3750:
%SFF8472-5-THRESHOLD_VIOLATION: Te2/0/1: Voltage low alarm; Operating value: 0.00 V, Threshold value: 3.07 V.
I used the command:
#sho interfaces transceiver
If device is externally calibrated, only calibrated values are printed.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
NA or N/A: not applicable, Tx: transmit, Rx: receive.
[Code]....
When I insert the TwinGig Converter in a Catalyst 4900M you get the following error message: Failed to read transceiver serial eeprom on port Te2/1, try reinserting.This error is probably because the device expects 10Gig transceivers to be connected to the device not 1Gig.I used the TwinGig 4 module and 8 SFP ports are connected. But when i type in the the "hw-module module <slot> port-group <group> select gigabitethernet" the command is not available. [code]
View 1 Replies View RelatedI have a catalyst 4506 switch with one sup-engine WS-X45-SUP6 L-E, which consist of two X2-10GB-SR Transceiver( CISCO).IOS on the sup-engine is cat4500e-ipbase-mz.150-2.SG1.bin. IOS detected only one X2-10GB-SR Transceiver in Ten1/2. When I insert the X2-10GB-SR Transceiver in Ten1/1
C4K_GLMMAN-3-X2PLUGGABLESEEPROMREADFAILED: Failed to read seeprom on port Te1/1. Reinsert X2 m
But the problem is i need two X2-10GB-SR Transceiver for Uplink.
I'm unable to get the N7K-M108X2-12L 10 Gbps Ethernet XL Module within our Nexus 7009 chassis to recognise the individual X2-10GB-SR transceiver modules. I have the same issue on another 7009 chassis.If I perform a 'show interface'. I get the following output saying SFP not inserted.
-Ethernet3/5 is down (SFP not inserted)
-Dedicated Interface
-Belongs to Po51
-Hardware: 10000 Ethernet, address: 7081.0599.d458 (bia 7081.0599.d458)
I also get the same result if I issue the following command. Are their any additional features I need to enable? or would this be a license issue?
Have already tried different X2-10GB-SR modules, reloading the card, re seating the card. [code]
I want to connect a Cisco small business switch (sf302-8) to a Cisco catalyst 2960S over a multi mode fiber. The transceiver I am using in the catalyst is a GLC-SX-MM. I presume in the SF302, I will have to use a MGBSX1. My question is "are these transceiver compatible with each other and if not, is there a transceiver that will suit both pieces of hardware?
View 2 Replies View RelatedI have a Cisco 5548 Nexus switch with 10Gbase-SR interface transceiver. This interface is connected to Server chasis.
The show interface transceiver details output shows High ++ alarm for Current. Additionally, i am getting output errors on this interface.
I am struggling to find an SFP transceiver, single mode, that operates at 100Mbps in a 1000Mbps port in an ME3600 or ME3800.
View 5 Replies View Relatedcan wireless router support up to 100 user including support network printer
View 1 Replies View RelatedI have confirmed this with TAC and also been told that a NCS MR2 is going to be coming soon and will have support for the 7.0.220.0 code.
View 3 Replies View RelatedI need to monitor SCE8000 alarms, but LMS does not support this product. My other Cisco products are managed by LMS. get visibility of SCE8000?
View 1 Replies View Relatedcan we install the ISO LMS 4.1 directly on a UCS platform?What platform UCS is supported?Do you have install experiences you can share?Is the ISO LMS 4.1 a Linux implementation?
View 6 Replies View RelatedCisco 2960 Optimization
The current software version is as follows:
System image file is "flash:c2960-lanbase-mz.122-35.SE5/
I WOULD LIKE TO KNOW THE UPGRADE PART TO BE ABLE TO ACCOMMPLISH THE FOLLOWING:
1. Deploy IOS Code containing Crypto ( K9 Image) features and reload the device with the new IOS
2. Generate RSA KEY on the network device + domain name.
3.set limit per MAC@to 4
4.set port to be protected instead of shutdown when limit exceeded
5.enable err disable recovery for link-flap events
6. set up required limits for port security settings preserving current NOD exception
7. i would like to know if i need to upgrade the IOS to achieve this. ?
I am not very familiar with the NM-8A/S module. There is a requrement to terminate a 2 MB link on 1 port of this module on a 2620 router. According to my limited knowladge about this interface it doesn't support more than 128 kb/s . if I can configure for 2 Mb
View 3 Replies View RelatedDoes cisco 887 support anyconnect vpn access?
View 1 Replies View RelatedI have a 2651 IOS ver 12.2(8) T5 and I installed an ATM-T1 4T1-IMA WIC, but the router will not recognize it. Do I need a newer IOS or is there a command to have the router recognize this WIC? Currently it is connecvted to our ISP via the serial connection, but they want to go to an ATM protocol for better video performance.
View 6 Replies View RelatedDoes Cisco 861 have EIGRP support?
View 1 Replies View RelatedI am trying to do Leap and Eap-TLS together. How can I write a policy in ACS that would check for identity before choosing the right profile for the request. ACS 5.2 does not support Native eap-tls. I am assuming I will be using Idenity username for Leap and Predefinied Certificate profile identity for eap-tls.
View 1 Replies View RelatedI found following spec in 8510 controller data sheet
Interfaces and Indicators
#• 2 x 10 Gigabit Ethernet interfaces
#• Small Form-Factor Pluggable (SFP) options (only Cisco SFPs supported): SFP-10G-SR
#• LED indicators: Network Link, Diagnostics
#• 1x Service Port: 10/100/1000 Mbps Ethernet (RJ-45)
However, I need Long Range SFP, i.e SFP-10G-LR
I have WLC 520 with software version 5.2.178. Currently we purchased Cisco AIR-LAP1131G access points and tried to join to WLC 520 but it is not joining. My question is WLC 520 will support 1131G access pont or not.?
View 1 Replies View RelatedI got a Cisco 870 router. running C870-ADVSECURITYK9-M), Version 12.4(15)T7, does this support two link from different ISP.
View 2 Replies View Relatedi just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
View 0 Replies View RelatedWe have 881 routers and are planning on testing out some WAN optimizing hardware, we're told that our router needs to support PBR and WCCP protocols. Will this router handle it?
View 3 Replies View RelatedI am upgrading from 7.0.116.0 to 7.2.110.0 to support the 3602 APs. Is it a different license to upgrade to 7.2.110.0 or can I directly upgrade to 7.2.110.0 without a new license?We currently have a 5508 base license.
View 1 Replies View Relatedwhat is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?