Cisco :: Reset DSP On 3600?
Jul 2, 2002How to reset DSP on the 2600 and 3600 without reset the controller or reset the routers.
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: WS-C2950-24 - What Last Reset From System-reset Means
Dec 10, 2012Does any know what " Last reset from system-reset " means? Is this becouse of a power failure or someone reloading the switch?
View 3 Replies View RelatedLinksys Access Point :: How To Reset WAP11 With No Reset Switch
Apr 16, 2013I have the WAP11 serial number G3110320414 that does not have a reset switch in the back. How do I get back to factory settings?
View 3 Replies View RelatedCisco Wireless :: WCS And WLC Versions For 3600 WAP
Mar 5, 2012I got a few Cisco Aironet 3602i. The minimum WLC version to support these is 7.1.91.0. I am planning to upgrade to 7.2.103.0. The minimum WCS version to support these WAP is 7.0.220.0 and the next available 7.0.230.0. Checking the release notes for both of these WCS versions, there is no mention of support for WLC versions listed above.
URL
Am I missing something here ? What versions would be required on WCS and WLC to make all the three entities (WLC, WCS, WAP) inter-operable ?
Cisco :: 3600 NCS / WLC 5508 And Clean Air
Apr 25, 2013we have this:1x wlc 5508 7.2.1031x cisco prime infrasture physical appliance 1.2And for test of clean air 1x ap 3600 seriesBut i have a question if i would like see bluetooth device in neighborhood. On the cisco web i founded 3355 or virtual appliance.
View 1 Replies View RelatedCisco :: 3600 Connection With Service Provider
Jul 9, 2012I have currently a Cisco 3600 router, it has three interfaces (all ethernet interfaces only).We being a client, our requirement is, we want two links one being the primary and one secondary for the fail over.My ISP has done certain configurations, but I am so puzzled what really has been done. I asked with them and they told that they have provided us one public IP 202.166.217.248 via Fibre--> Media Converter-->Ethernet 0/0.At the same time, they have given us a pool of addresses of the network 202.166.216.48/29 through the interface Ethernet 2/1.And we have used all the available public IPs in the server farm.They have told that, for the failover purpose via wireless, they have even used an IP address 202.166.213.114/25.
Now, where my confusion lies is, cant they provide the pool address via fibre? What is the significance of the ip that has been provided via fibre? What actually is its purpose? Isn't it consuming an extra interface ?Cant we have both the primary and secondary link excluding that one additional process?Or, am not understanding the real working mechanism how ISP distribute the internet?
Cisco Wireless :: Use A 3600 For An Ethernet Bridge?
Oct 18, 2012Can you use a Cisco 3600 to do a P2P bridge? Using the MAP's ethernet port to connect to a remote LAN? On that remote LAN can you have lightweight APs that connect to a controller on the RAP side?
View 13 Replies View RelatedCisco Wireless :: Concurrent Users Per 3600?
May 7, 2012This is one I am having a hard time finding an answer for. How many clients can a 3600 AP support? For 150 clients on one of these, what would the throughput be for each client?
If my calculations are correct, the device can deliver 420 Mbps, which gives each client roughly 2.8Mbps. Is this correct?
Cisco Infrastructure :: 3600 With Power Connector But Do Not Have RPS
Nov 4, 2012I have a router 3600 with a power connector kind RPS but I don't have a RPS system, Do it exist a kind of wire that I can connect directly from my router to AC?
View 1 Replies View RelatedCisco AAA/Identity/Nac :: 3600 - EAP-TLS Machine Authentication ACS 5.2?
Mar 26, 2012we have a customer with a wifi deployment aruba 3600 controller based. Corporate SSID authentication is EAP-TLS double machine and user authentication through ACS 4.2 against AD and Microsoft AC PKI infraestructure based; it was working ok. After migrating from ACS 4.2 to 5.2, both authentication (machine and user) are reported as succeed by ACS but aruba controller does not recognize machine authentication. It seems that controller sees two authentication users and not an machine followed by and user one. We have revised configuration in detail and it seems correct. We begin thinking it could be a bug .
View 2 Replies View RelatedCisco Wireless :: 3600 AP Mounting Bracket
Jun 25, 2012if the mounting bracket for 3600 AP is the same as the 3500/1140/1040 mounting bracket? I'm suspecting it's not as you can get modules that fit onto the back of the 3600 APs.
View 4 Replies View RelatedCisco :: NCS 3600 Where To Find Software Version
Jan 28, 2013Cant find the software version on my NCS .Apparently once we start using 3600 APs then we need to upgrade.Cisco AP 3600 was introduced in the 7.1.91 or later code stream and is supported by the following: Cisco 2500, 7500, 5508 and WiSM2 Series Controllers, and WCS 7.0.220 or later and NCS 1.1 or later.
Problem is no matter where i look i cant find the current software version for it.
Cisco Wireless :: Converting 3600 To Autonomous?
Jan 13, 2013I am not having much luck getting it converted via normal ways.
It times outs on TFTP server when you hold the mode button (a 3500 is working fine doing the same thing).
I try the old school way of archive download-sw but it isn't fast enough before it re-dhcp's because it can't find a controller. "*Mar 1 01:17:51.123: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP..' Even if I set a static IP address.
Is there way to disable the join process while I upgrade the software? I guess fire up a controller for it to join. I hope I don't have to have a controller to convert these.
Cisco WAN :: 8510 - BVI On Catalyst 3600 Can't Communicate With It
Jul 27, 2011Have been struggling with a connectivity issue following a recent power surge from a storm. A BVI from Cisco Catalyst 3600 cannot communicate with our local network.
We have several satellite connections which connect to us via ADSL. From these satellite offices I can talk to the Cisco 3600 we have here at our central office (BVI 10.60.112.1). There is a connection from the ATM port on the Cisco 3600 which goes to an ATM port on a Cisco Catalyst 8510 and there is an Ethernet connection from that 8510 to the core switch on our local network (Catalyst 6509).
Since I can talk to the 3600 without issue, I believe that the issue is the 8510 config.
There are only two ports in use on the 8510.The ATM port on the 3600 is connected to the 8510's ATM0/0/1.The 8510's ATM1/0/0 (622MM) is connected to our local network's core.There is activity on both ports of the 8510, but from the local network I cannot see 10.60.112.1 and from the 3600 I cannot see the core.
The 8510 config looks pretty default, like some things were "lost" during the surge (we had backups of the 3600 and not the 8510). The config goes as follows for the 8500:
[code]....
Cisco WAN :: 3600 BGP Peer Closed Status
Nov 21, 2011i still newbie to configure eBGP, i have Router 3600 series, and i configure BGP neighbor to my ISP, but the peer still don't established,there is warning like this, Connections established 339; dropped 339 "Last reset 2w4d, due to Peer closed the session No active TCP connection"
any one can explain to me about "due to Peer closed the session"? i've read some documents for troubleshooting BGP, and do some step to troubleshoot.
Cisco Wireless :: 5508 Can't Add 3600 Series AP To Group
Jul 22, 2012I have an AP group on a Cisco 5508 WLAN controller. Currently, it is populated with 13 Cisco 1142 lightweight access points. When I try to add a Cisco 3602i access point to the group, I get the following error in NCS: Error: OfficeExtend requires primary, secondary, or tertiary controller management IP to be set.I am using DNS to allow my AP's to find the controller and they work just fine. Is there a reason I can't add the 3600 series AP's to the AP group?
View 13 Replies View RelatedCisco Wireless :: 5508 WLC Code Upgrade / WCS AP 3600?
May 8, 2012i'm going to upgrade a 5508 wlc code from 7.0.116.0 to 7.1.91.0 to add 3600 series access points having it all manageable via WCS ver 7.0.230.0 it seems to be possible, as it is explained in the compatibility matrix found on [URL]now I have to download the file to the controller...
AIR-CT5500-K9-SPECIAL-7-1-91-0.aes
(direct update possible)
before doing that I'd like to know if I will loose my configuration on the controller i'm concerned about that because the release document is not clear:
- We highly recommend that you back up your controller's configuration files prior to upgrading the controller software. Otherwise, you must manually reconfigure the controller.
- For busy networks, controllers on high utilization, or small controller platforms it is advisable to disable the 802.11a/b/g networks as a precautionary measure.
- Step 5 Disable any WLANs on the controller.
- Step 19 Re-enable the WLANs......
- Step 22 If desired, reload your latest configuration file to the controller. (reload config after reenabling wlans?another controller another question .....: a cisco wlc 2100
found 2 update files
AIR-WLC2100-K9-7-0-230-0-ER.aes
AIR-WLC2100-K9-7-0-230-0.aes
why 2 update files this time? what file to update first?
Cisco WAN :: 7609 / 3600 - How To Set VLAN Based VRF Selection
Jan 9, 2013I am using Cisco 7609 IOS15.0(1)S1 and Cisco 3600 IOS 15.1(2)EY.I am trying to provision VPNs over MPLS network.All I found in the documentation is how I attach a whole interface to a VRF.However, I need to be able to attach a VLAN (or any other matching criteria, for that matter) to a VRF.In other words, I want to be able to attach port 1/1 vlan 100 to VRF-A and port 1/1 vlan 200 to VRF-B.
View 1 Replies View RelatedCisco Wireless :: Antennas Doesn't Work On AP 3600
Mar 6, 2013I´m trying to test anntenas in a AIR-CAP3062E-A-K9 the problem is that when I´m below the AP the speed is weak, the AP es with a WLC, so I was wondering if do you know a command or a form to test the anntenas or the Radio.
View 7 Replies View RelatedCisco Wireless :: Adding 3600 Series To WLC 5508?
Mar 26, 2013I have a 5508 controller with a bunch of 3600 Series APs. I did all the basic config on the controller and added all the APs through distribution port #1. Now I was trying to config a second interface ( port #2) and use it for the Guest SSID on a separate VLAN. After I rebooted the controller, it dumped all the APs. I would like to know if this is normal, If I need to enroll the APs everytime I reboot the controller.
View 1 Replies View RelatedCisco Infrastructure :: Can 3600 Support IP Addresses And VLANs And How
May 6, 2012I am working on my CCENT after getting my A+. I have an old 3600 router and I am following CBT Nuggets to configure it. CBT Nuggets seems to have an IOS that supports VLAN and IP Addresses and it looks like mine only goes up to Token Ring so it doesn't mirror the instruction. I know it's an old router but is there a software release (like the 12.4 maybe?) that would allow me to follow the CBT Nuggets more accurately so that I can set the switch up for IP Addresses and VLAN instead of limiting me to token ring?
View 1 Replies View RelatedCisco Wireless :: Downgrade 3600 Capwap AP To Autonomous
Nov 12, 2012I have to prepare an 3600 Capwap AP for autonomous functionality!
The following image was downloaded: ap3g2-k9w7-tar.152-2.JA
The release notes say: Site-Survey Only Mode for 3600, 3500, and 1550 Access Points You can install Cisco IOS Release 15.2(2)JA on Cisco Aironet 3600 and 3500 Series access points and on 1550 series outdoor access points to perform site surveys. This release runs on these access points with limited functionality. You can manually adjust these settings on the site-survey access points:
• Channel on each radio
• Transmit power on each radio
• Enable and disable the radios
• Manually set basic and supported transmit rates
• Enable advertised cell power in beacons to client to enable DTPC for doing active surveys
• Enable and disable SSID broadcast in beacons
• Enable open authentication
My Question is: Where can i find a instruction for downgrading an AIR-CAP3602i to Autonomous 3600 AP? Is it complicate to get the AP running, or what do i need for "downgrading"?
Cisco :: Nexus 5596 / Metro 3600 Switches Do Not Come Up On LMS 3.2
Nov 19, 2012I am running LMS 3.2 and can not see the Nexus 5596 / ME-3600X-24FS-M Cisco switches on Cisco works LMS 3.2. Where I need them most is DFM the devices come up as unknown. An example below 10.125.202.1 is NExus 5596 and the rest are ME3600.
208.10.125.202.1UnknownN/AN/A209.10.115.1.4UnknownN/AN/A210.10.115.1.3UnknownN/AN/A211.10.115.1.2UnknownN/AN/A212.10.115.1.1UnknownN/AN/A
going through the article below looks like its not supported
[URL]
What are the options I have next ? Can I upgrade to LMS 3.3 or only do an upgrade for DFM ?
Want to avoid LMS 4 as that's an installation from scratch.
Cisco WAN :: 2621 / 3600 / 5505 - Work With BT Infinity
Mar 20, 2012We have an existing Cisco 2621 XM router with an ADSL interface connected to BT Broadband. Basic layout below:
Internet------ADSL on Cisco 2621 ------ Pix 506e ---- 3600 switch with inter VLAN routing to multiple VLANS
There are 5 static IP addresses. The internal FE port on the 2621 has one external assigned to it. The outside int of the PIX has another external IP assigned from the 5. The other 3 are NATd through to internal IPs via the PIX to internal servers etc.
The ADSL is being upgraded to BT Infinity. This new service comes with a separate VDSL modem and a separate BT router. Ideally I want to ignore the BT router and use the Cisco 2621 as it has 2 FE ports and I suspect I could do something using PPPOE.
So New layout would look like
Internet ----- BT VDSL modem------ Cisco 2621 ----- Pix 506e ---- 3600 switch with interVLAN routing to multiple VLANS
I think it is a bit strange the way it is setup as 2 static IPs cant be used. There is an opportunity to use a ASA 5505 which may become available.
Cisco Wireless :: 3600 - Use FlexConnect In Same Network Where WLC Located?
Feb 3, 2013I want to use the flexconnect in the same network where the wlc is located. Normally we will do it for over WAN and branch office. But I want to use in the same main office to avoid more bandwidth utilization on my distribution layer. Wlc is connected on Distribution switch.I want to do local switching in the access layer switch.
The below is the sample topology. But real topology contains nearly 200 AP's(3600 series) and 20 access switches and so on.....So there is a chance of 200 AP * 350 Mbps can flow on the distribution layer.So ,
1)If I use flexconnect any issues will be occuring?
2)Does it cause any impact on VOWLAN?
Cisco Wireless :: 3600 Access Points In Bridge Mode
Apr 3, 2013I am trying to build a bridge between two of my access points. Both the access points connected to the wireless controller. I have changed the AP mode to "Bridge" after changing the power to custom.
The access points have both rebooted - but never "joined" the controller again. I have checked on the following pdf.
[URL]
One thing I can see - if I run a ping to the last IP.. every now and again I get a single response then it drops again. Via the console on the access point I can see it's getting to the controller, getting its name then reading something that caught my eye
"
*Apr 4 11:41:24.451: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 4 11:41:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
[Code]......
Cisco Wireless :: Mixing And Connecting 1262 With 2600 And 3600
Apr 23, 2013I am don't need anything unusual and I would love to go with the 2600/3600 APs, unless mixing them up is a problem.
View 2 Replies View RelatedCisco Wireless :: Maximum Power Settings Spec For 3600 AP?
Oct 14, 2012I am looking for the Maximum Power Settings Spec for the 3600 AP. The one from 2008 is too old. Does an update exist? The AP Spec itself does not show power levels by channel and regulatory domain which is what I need. If I can't get the spec, I will have to query the AP using "show ap config 802.11x apname" for each config I need.
View 1 Replies View RelatedCisco Wireless :: 3500 / 3600 - Post 7.2.111-3 Upgrade Lost All APs?
Feb 8, 2013Lost my access points to controller. Not sure if it was related to upgrade from 7.1 to 7.2, or something else.
The console log on APs shows;
*Mar 1 00:01:09.394: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 1 10:24:23.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 142.100.64.8 peer_port: 5246
*Jan 1 10:24:23.424: %DTLS-5-ALERT: Received FATAL : Certificate unknown alert from 142.100.64.8
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Bad certificate alert received from peer.
*Jan 1 10:24:23.424: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 142.100.64.8:5246
*Jan 1 10:24:23.424: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
All 3500/3600 APs, had been in production for months.
Cisco Wireless :: Adding 3600 Series AP To 4404 WLAN?
Jun 3, 2012I've got a client who purchased numerous 3600 series AP's (3602i to be exact) and would like to add them into their WLAN 4404 controller. They're currently on 5.x system code so I plan on getting them upgraded to the latest 7 code.
They currently have a number of AP's adding and working fine. Once the WLAN controller is upgraded, does anything specific need to be done within the WLAN gui to add in these new 3600 series AP's?
Cisco Wireless :: How To Enable 100mbps Speed On WLC 2504 With 3600 AP
Sep 13, 2012i have cisco wlc 2504 connected with cisco 3600 ap,now the customer required n bandwidth speed ,but in wlc am not able to enable n bandwidth for ssid.in radio policy of ssid also n bandwidth is not showing,only this bandwidth showing a/g,g,b/g, and all?
View 8 Replies View RelatedCisco Switching/Routing :: Password Recovery On 3600 Router?
Dec 5, 2012I'm using the ctrl-break sequence in hyperterminal during the the initial boot, and it's hanging.
View 1 Replies View RelatedCisco Wireless :: Controller Software That Supports 3600 And 1231 APs?
Dec 4, 2011Customer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
View 6 Replies View Related