Can it limit streaming websites? example "youtube" and torrent downloads? and dont affect other websites/ gaming speeds currently has 50 units connected with 2 ADSL connections both with maximum down of upto 4.5mbps.
View 2 Replies
how to limit the bandwidth in digicom router?
View 2 Replies View RelatedI have a problem with 2 users in the home network who overuse the internet. They constantly watch YouTube with Pandora turned on or other streaming content.We have RW110. How can I limit their bandwidth, so when they use the internet they do not block other users ?
View 1 Replies View RelatedBuy a router RV120W, and one of the reasons is limit of bandwidth (QoS). I set up a profile of 1-256 kbps limit, and apply it to the only VLAN that is configured, but does not work and can navigate using the full bandwidth of the internet connection. My firmware version is 1.0.2.6
View 8 Replies View RelatedSince I've bought my RV042 CISCO (v3 hardware, firmware v4.1.1.01-sp Dec 6 2011 20:03:18) i wasn't able to let it work properly with my two DSL network lines. I explain. I got 2 DSL network:
1- PPPoE with authentication (MTU setted as auto) with upstream speed 4Mbit/S and downstream speed 5Mbit/s
2- Direct line with static IP with upstream speed 7Mbit/S and downstream speed 1Mbit/s
I was never able to SUM the two WAN using the LOAD BALANCE set. I tried all combinations:
DSL 1 in WAN 1 or in WAN 2
DSL 2 in WAN 2 or in WAN 1
I've tested all type of speeds in WAN SPEED in Web Management
it seems that for some kind of reason it takes the upstream speed i can set in web management as the default value on which it decides to use the other WAN. When i set low upstream bandwidth for DSL 2 it's able to sum the down streams of both WANs but not the up streams.
I wasn't ever able to sum the up streams? How does it work?
I am trying to set up my router to grant http traffic a minimum bandwidth of - for example - 5,000 kBit (if there is any http traffic).
So I set http min. rate to 5,000 while I set nntp min. rate to 1 However, when I run nntp downloads on several connections (e.g. 10) my single http download never goes above 1,000 kBit. Without any other connections I reach 8,000 kBit.
I am using a single 12 MBit line.
I am planning to buy a router for my hotel and I would like to know is it possible to limit the bandwidth limit to the guests? And the admin computer can utilize the maximum speed? it it possible to create a login page paper when some one enters my wifi connection?
View 7 Replies View RelatedMy children are enrolled in an online school. Is there a way to restrict access to allow access to the school site only with the option to toggle this on and off?
View 2 Replies View RelatedI am a Network admin of 200 Computers.Most of our users used to download movies through torrents.I just want to now how can i limit the bandwidth for specific user for both domain and work group user
View 4 Replies View RelatedIs there a way to limit a whole PC windows XP, or a certain program to use only a certain about of your total internet connection bandwidth?For example, I have 5 PCs in home all one the same ISP connection. I have one PC that I am trying to backup files online but I can only run it at certain times due to the backup program using ALL upload/download speed. And that makes every other PC super slow.
View 3 Replies View RelatedIf a person downloads via ADSL2 5 GB how much bandwith would this require?
View 1 Replies View RelatedI am using ASA 5505 cisco firewall as a transparent firewall. I have assigned ethernet 0/0 as outside interface and ethernet0/1-7 as inside interface. There are 3 departments in office. So, i connected ethernet 0/1 to Dept A, ethernet 0/2 to Dept B and ethernet 0/3 to Dept C. Now, I want to limit bandwidth to each department, e.g, 1 Mbps download/upload to Dept A, 512 kbps download/upload to Dept B and 512 kbps download/upload to Dept C. So, how can i do this in ASA 5505.?
View 1 Replies View RelatedIf two (one 6509A 9/26 with server A located in A end, 6509B with serverB located in B End) which is connected via a 1G link. If there is serverA send 700M file to server B via a 1G link. If I configured below command to 6509A 9/26, can I limit the bandwidth of server on bothincoming and outgoing to 500M?
class-map match-all FROM-SERVERmatch access-group name FROM-SERVER!policy-map FROM-SERVERclass FROM-SERVERpolice 500000000 conform-action transmit exceed-action drop!interface GigabitEthernet9/26service-policy in FROM-SERVER
I have a 3845 Router with three connected interfaces, one to my WAN, one to my LAN and another to my wifi zone. I want to limit the amount of WAN bandwidth the WIFI zone can take to say a max of one third and not restrict WAN bandwidth from the LAN at all.
View 7 Replies View RelatedI have cisco 7600 core router in ISP , i want to put the bandwidth limit on it for outgoing traffic (for internet) on a subnet because i am using Bluecoat and i want to test my bluecoat.On this subnet i have no limit for bluecoat but after the bluecoat i want to limit it. On 7600 cisco router i have not rate limit command so how it can be possible for a perticular subnet ?
View 1 Replies View RelatedI have two vlan interfaces, how to limit bandwidth on them ?I need than speed on each will be direrent.
View 1 Replies View RelatedVLAN ===> FE 0/1 {With subinterfaces - ALL INSIDE LAN INTERFACES} ==> ROUTER ===> BVI 0/1 {WAN Interface - OUTSIDE}
i am doing NAT for my clients in LAN to WAN - Static NAT i want one of my client who is excessing some service with his Public IP to get a specific amount of bandwidth ... as right now he is hogging all the bandwidth .i have 1841 router.
I want to switch to a slower ISP because of financial constraints (specifically downgrade from cable to DSL), so I'd like to set up my Windows XP computer so that it downloads and uploads at the same speed that the slower ISP does. That way I can kind of "try before I buy" for a week or so, to get an idea if I can live with the slower speed before disconnecting from cable and incurring a disconnect charge. I was told that some software that limits your bandwidth also may cause distortion in video or audio streams, so I'd like to avoid that.
View 2 Replies View RelatedMy router is a GT704-WG running on the default firmware. I need to limit a certain computer's bandwidth. Am I able to set the maximum download/upload speed for a certain computer via the router control panel (192.168.1.1)?
View 11 Replies View RelatedOn my home network I have 11 devices connected.Is there a way I can give each device a certain bandwidth limit so my Internet doesn't keep getting sucked up?
View 5 Replies View Relatedi have a internet cafe. i need to limit the bandwidth of our 30 computers for our customers satisfaction.
View 7 Replies View RelatedThe Nordic World Ski Championships 2011 is upon us, and NRK, the national broadcaster of Norway, is offering HD streaming via the Akamai network.I run a network with 5000 users. Our internet bandwidth is usually 300mbps, but we've increased it to 500mbps for the duration of the Ski Championship. that did not work, because of the HD streaming.The internet link is delivered on a fiber trunk with many other VLANs, and my first piece of equipment in the chain is a Cisco 3560G (C3560-IPBASEK9-M), Version 12.2(46)SE). A port on the 3560G is then set to switchport access vlan "internet-vlan", and that port is connected to a routed port on my Cisco 6509-Sup720-10G ( (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH3a). The 6500 then routes the traffic to a Cisco ASA 5520 (running 8.2(4)).What I'd like to do, is to limit the total bandwidth of all conversations between our IPs and the nearest Akamai IP-range, which is 195.18.221.128/25.How can I achieve that? I've tried to read the QoS chapter from the manual of the 3560G 12.2(46), but QoS is very complex stuff?
View 8 Replies View RelatedWe have a Cisco 3845 router and on the G0/0 interface we have our public switch with multiple public IP addresses (servers, routers, etc..) and on the S0/0 interface we have a DS3 Internet connection. I need to limit the bandwidth from the Internet (download) to one of the IP addresses on the G0/0 interface. I'm thinking of limiting to 256K and really need info with either a policy map or something equivalent.
View 6 Replies View RelatedI am using ASA Version 8.2(1) , I want to limit the vpn users to use less bandwidth of my Interlink to access something on inside network
example : source vpn pool
Destn : inside network
how can achive this with QOS config.
we have a bandwidth pipe terminating on 1841 BVI interface... now we want to limit all the traffic going from inside to WAN circuit to half... for example 10 Mb pipe we want to reduce to 5 mb on bvi interface.. how this can be done .. as of not there is not need to police any specific type of traffic .. this needs to be done for any traffic from inside to outside...
View 1 Replies View RelatedI currently have a 20mb connection with sky. I have 4 computers in my household and using the wireless modem router to distribute the connection.can I limit each computer to a certain amount of bandwidth. (eg PC1 =5mb, PC2=5mb, PC3=5mb, PC4=5mb) Two of my computers are running Win Vista HP and two computers are running Win 7 Pro & Ultimate.
View 1 Replies View RelatedI have a roommate who takes up a lot of bandwidth from the internet. I am allowing him to use my router which is a Linksys E2500. Is there anyway to limit how much bandwidth he can actually use.
View 1 Replies View RelatedHow can I limit the bandwidth of a router (DIR 600).
View 1 Replies View RelatedI have a 20MB internet connection, with a 100GB cap. My mother works at home, with some employees. Adding home and work, 8 people use the internet all the time. Lots of Youtube videos, streaming netflix, iTunes downloading, and so on.I wanted something to:
1) Manage this cap. It's over too soon, and we're left with a poor internet connection until the end of the month - like 500kb.
2) Something to manage two internet connections.
I was thinking about a dedicated router - I currently use a WRT54G V8, which is nice, but it has some issues handling the traffic when the internet is in its full glory. I heard about pfSense, and some searches on Google tell me it's possible to do both options using it.
Any example to limit the bandwidth using the MAC address on 2960 ? I want to limit the bandwidth (IN / OUT) of a server only for Internet flows.
View 2 Replies View RelatedIs there any possibility to limit the bandwidth per SSID on Cisco Aironet 1100 that is connected to Cisco router 876? So the main goal is to have two SSID one for the guests and one for the colleagues and to limit for example half the bandwidth of internet link per SSID so we dont get into situation that colleagues overload whole internet link so that guests can always surf without problem.
View 3 Replies View RelatedI'm having a bit trouble to limit the bandwidth on outgoing traffic with a Cisco ASA 5505.
In my case I want to limit the bandwidth to 31mbit/s up and down on the outside interface. but with my current configuration, just the download rate gets limited to 31mbit/s when I do a tptest. and the upload is around 40/50mbit.
Here is the policy configuration,
access-list outside_bw extended permit ip any any
class-map outside_bw
match access-list outside_bw
[Code].....
I apologize in advance if this is a novice inquiry, but our company just switched from Point-to-Point T1's to Metro Ethernet.
On one point-to-point, from our main office to one of our high profile locations, we had two bonded T1's. Now this site has a 3 Mbps Metro-E link, but it's being over-saturated. I don't know what type of QOS implementation our T1 provider had, but it prevented flooding. Now, I'm getting horrendous latency as the office peak hours approach since there is no QOS on the mesh by our Metro-E providers.
Ultimately, my question is: what's the best way to set a Fast Ethernet port on a Cisco 1800 series router to limit all bandwidth to 3 Mbps? At the moment, I don't have a preference in which traffic takes priority. I tried the rate-limit command, along with a speed calculator I found online, but that slowed the network down immensely.
