Cisco Routers :: ISA570W / DHCP Reservation For Multiple Clients At Once?
Jun 4, 2013
All the SOHO routers I have used had a table which shows IP, MAC, Name, etc. In this table, I could easily put a check mark to a check box in a row that I would like to bind/reserve and IP would be reserved for that specific MAC.
In ISA570W, when I need to reserve/bind an IP to a MAC it asks me to fill out a table in which I have to manually type in the name, IP, and MAC.
Is there an easier way?Is there a way to do the reservation for multiple clients at once?If this is the only way, do I need to copy the mac address of each client somewhere and then reserve IPs for each one manually? This method looks very far from user friendly and efficient, unless there is a very logical reason that I cannot think of.
View 2 Replies
ADVERTISEMENT
Jun 6, 2013
I have some issue with a newly purchased ISA 570W; we are moving from a Cisco RV220W to this new ISA570W but the WAN interface will not auto negotiate on 1000 Mbit. It is only possible to forced it for 100 Mbit, but then the Internet connection is really slow (properly collision) 5 to 6 mbit up and download on a 200 Mbit ISP connect, our "old" RV220W run auto negotiate 1000 mbit FULL on the WAN interfaces and we have no issues with the bandwidth on this box.
View 4 Replies
View Related
Feb 7, 2012
I have a Blackberry Playbook and have come into a problem with it.I can't set a Static IP on it so would setting a DHCP Reservation in my Linksys E2500 router act as a static IP?
View 2 Replies
View Related
Apr 2, 2011
I'm using TP Link router. I went to DHCP reservation list and provided mac address of a computer and ip address to reserve the ip address for the computer. But it still not changing my current ip address. I rebooted router, rebotted computer, but it still not changing to the reserved ip.
View 3 Replies
View Related
Jun 27, 2012
why my switch is not picking up a reserved address from the second pool below?console output with dhcp debugging on.ps. I have also tried 'hardware-address 0024.f769.bf40 1' which is hardware type 'other'
Config
ip dhcp excluded-address 172.23.23.1 172.23.23.49
!
ip dhcp pool main
import all
network 172.23.23.0 255.255.255.0
[code].....
View 3 Replies
View Related
Jul 11, 2012
I have a few sites using the RV042 with wireless access points and some of them have over 50 devices.In reviewing the documentation (specifically,[URL]), I came across this:Enable DHCP server: Check the box to allow the router to dynamically assign IP addresses to up to 50 connected devices. Uncheck the box if you have another DHCP server on the network or you want to configure static IP addresses for your network devices.Is this accurate? Or will the RV042 allow more than 50 devices?
View 3 Replies
View Related
Oct 9, 2012
I have a Cisco RV220W running the latest firmware (currently 1.0.4.17), and I have noticed that after about a week of use, wireless clients can no longer acquire IP addresses via DHCP.
I have used Network Monitor on both the DHCP server, and the WiFi client, and can see that the server is receiving the requests and sending a reply, but the client never sees the response from the server. So far the only way to resolve this is to reboot the router.
View 10 Replies
View Related
Nov 26, 2012
Is there a way on the security appliance SA520 to remove someone from the DHCP lease client manually rather than setting the DHCP lease time to expire in less time like 4 hours or 2 hours. I was able to do this on other routers by highlighting the connected device and click remove. If not any recommendations on how to handle the device that are attached via DHCP and the person is no longer here, but the lease time is not up. I have set DHCP lease time to 4 hours.
View 1 Replies
View Related
Oct 6, 2012
I have simple set-up in my network with 2 routers connected to each other, 2nd router is just kind of wireless access point and switch to extend cable sockets upstairs.I have DHCP reservation on the first router and it works perfectly. Second router has DHCP server disabled, and I have configured DHCP reservation same as the first router, but it gives random IP addressess instead of reserved. how can I configure second router to obtain MAC DHCP RESERVATION TABLE from the 1st router?
View 7 Replies
View Related
Apr 19, 2012
Is it possible to set up DHCP server with reservations for specific IPs?
View 1 Replies
View Related
Mar 5, 2012
Ever since I updated my firmware to 1.01 my web interface for the network settings screen has been random. Somtimes it shows a DHCP reservation list, sometimes it doesn't. Sometimes there are reservations, sometimes there are selectable radio buttons. I guess I'm just trying to figure out if this is a firmware issue or not. Ever since I updated the firmware it has been flakey.... But I was having issues with other stuff before that. When there are no reservations, sometimes i can't even select any computers because there aren't any in the drop down, when all of my hardware is online?
View 6 Replies
View Related
Jul 24, 2008
How can I use the dhcp reservation with this router? I've network printer and i can't use it.
View 6 Replies
View Related
Jun 9, 2011
When I'm in Setup -> Basic Setup -> click on DHCP Reservation, I don't see all entries I've created earlier but computers that connect still have the correct IP address on the network; I don't know if I can create additional entries if nothing appears
When I go to Status -> Local Network -> DHCP Client Table the list is blank but some computers are connected to the networkI'm using firmware 1.0.01 build 10 Feb 21, 2011, language = English, Firefox 4.0.1.Rebooting the router doesn't change anything, I can't see connected LAN equipment and DHCP Reservation is empty despite the fact I've created entries.Together with the "Access Restriction" which doesn't allow to block a computer from 10pm => 8am unless you create 2 rules + various issues with attached USB + 2.4Ghz signal that is far from optimal (never able to achieve more than 144-N-Mbps) and I ask myself if I will not contact the store where I purchased this unit and ask a refund (and buy something else from another brand...)
View 9 Replies
View Related
May 12, 2013
I tried to enter a name that included an illegal character (in this case, a single quote), and it gave me the popup box that said I had done so. When the popup closed, my DHCP reservation table was emptied out (I had maybe 5-6 reserved clients). In fact, I can't add new reservations anymore at all from this screen as it lists nothing in the DHCP clients table at the top. (Note, there are plenty of things in the DHCP Clients table over on the Status->Local Network tab). At this point, I think that my pre-existing reservations are still being held, but I'm not sure as it's only been about an hour so nothing has renewed.
I had firmware 1.0.05 when I encountered this problem. I upgraded to 1.0.07 as a means of trying to kick it into action, but the problem still exists.
View 1 Replies
View Related
Jul 9, 2010
I've just got a WAG120N router and can't see anyway to see what devices are attached to the router or be able to assign static IP's
View 3 Replies
View Related
Sep 24, 2011
my researvation table is incomplete. Below I show ipconfig that shows wired & wireless NICs assigned ip addresses by the E3200 router but the DHCP table only shows one.
I need to reserve the ip address of the wired address but can't get at it.
View 2 Replies
View Related
Jan 19, 2013
I have Linksys E3000 Router and it is connected to 7 Devices at this moment via DHCP. I have got New NAS Enclousre (8th Device) which has got Lan port . I have connected Box to One free Port on E3000 Router. I see DHCP Reservation from 192.168.0.1 assging one IP to My NAS Enclosure Box i.e 192.168.0.13 But when i ping that box . It's not pingable. When i try to browse that NAS Enclosure's setup web page - it's not opening. I can access that box setup page if i connect direct 1:1 Lan cable over private network (169.254.XXX). It means web server is runing on box. I am clueless. E3000 is assigning IP to NAS Enclosure but can't Browse or Ping. I tried to Assign Manual IP address to NAS enclusure and reconnect to router. Still I can't ping or browse.
#arp -a show that box has IP. (Output from MAC os) .
? (192.168.0.13) at (incomplete) on en0 ifscope [ethernet]
Ping test from Router Page.
PING 192.162.0.13 (192.162.0.13): 32 data bytes
40 bytes from 192.162.0.13: icmp_seq=0 ttl=46 time=286.6 ms
40 bytes from 192.162.0.13: icmp_seq=1 ttl=46 time=290.2 ms
[code]....
View 9 Replies
View Related
Jul 3, 2012
Before upgrading my firmware on my EA2700, I can easily reserve IP address for my wired device. With the new cloud interface, I click to select the device from the top pane to bring it down in the reserved IP pane below. When I try to save the IP change I get two errors: 1) Invalid characters in the device name 2) Invalid IP address. I get the same errors even if I do not edid not edit the name or IP address.
As for the device name, I did not change anything or rename the device. One device has a " - " in the name and the router was happy with it until I tried to reserve the IP. Another one had a " ' " in the name, same problem again.
My network DHCP range is set to 192.168.1.200 to 192.168.1.250 and I use the range from 192.168.1.1 to 192.168.100 for static IP. When I tried to reserve a static IP below 192.168.1.200, the router say that is an invalid IP.
The workaround to this problem has been to temporary set the DHCP range to 192.168.1.1 to 192.168.1.50 and set the static IP in that range and rename the devices to a name that the EA2700 will accept. Next I move the DHCP range from 192.168.1.50 to 192.168.1.100 and repeat the process. After, all the static IP are assigned, then I can reset the DHCP range to 192.168.1.200 to 192.168.1.250.
This is a pain to do. In the previous (cloud less) version, this was a breeze to do. Also, I have not figured out how to redirect ports with the new interface. Is that progress?
View 9 Replies
View Related
Jul 27, 2011
i am having an annoying issue with my wrt400n and my foscam FI8918W. in the dhcp reservation tab, the wrt400n doesn't show the foscam anywhere in the tab. it shows all laptops, cell phones, nases, etc. if i use the cisco connect software it does show it in the network map. i can probably add it manually via the gui. is this something normal or security cams not considered devices?
View 1 Replies
View Related
Mar 26, 2013
E4200v2, firmware 2.1.39.145204
Router says "Invalid IP address" when I try to make a manual IP address reservation of the IP address range.
Example: local network 192.168.1.0/24, where .1 is a router, .2 is a reservation, .20-.50 is a range for DHCP.
Before upgrade I didn't have this problem.
View 6 Replies
View Related
Jun 7, 2011
I have the e4200 and I am having trouble getting DHCP reservation to work properly with my Windows 7 machines. Perhaps there is a step that I am missing. Basically I go to the DHCP reservation setup page, select my machine and add it to the reservation table. Then I save the changes. As soon as I do this my computer goes offline. If I reboot my machine, it is still offline. I've tried the same procedure to reserve the IP address for my phone and it works fine so I wonder if the problem is with Win7.
View 6 Replies
View Related
Sep 18, 2012
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Apr 24, 2013
I purchased the Belkin N600DB, but I can't seem to find a way to reserve IP addresses for my connected devices. I need to run a server through the router, but (naturally) it keeps changing my local IP address. I cannot find the reservation utility.
View 1 Replies
View Related
Feb 1, 2011
I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies
View Related
Mar 2, 2011
Is it possible to set up a pppoe client on a VLAN interface, or a switch interface associated to an VLAN?. For example, in a 881 ethernet router, could I configure a pppoe client on any of the lan interfaces in addition to the pppoe client configured on the WAN interface?.
View 4 Replies
View Related
Jun 28, 2011
I've inherited some ACS appliances from another part of my organization. I need to keep most of the settings but want to remove all the AAA clients; and preferably not one-by-one. I don't see a way in the documentation and web searches have proven fruitless.
View 1 Replies
View Related
Feb 8, 2012
On every floor there are 10 rooms which can have multiple clients (laptops, ipads, smart phones) so let's say 50 clients.how to set up whole thing so the users in every room have decent speed for surfing and watching videos online
[code]...
View 5 Replies
View Related
Mar 30, 2012
I just want to keep one PC as a server and one switch connect to it (For LAN). I want to connect multiple client/screen to that server, so I can use single servers for multiple screen/client.(Client machine will not have any CPU, they will utilize servers memory.)
View 1 Replies
View Related
Nov 4, 2012
I have a 4402 which is connected to a 4506 Switch int Gig 3/1 via a trunk port. The Managment and AP-manger interfaces are on vlan 6 [code] I have a 1142N AP also connected to the switch and it pulls a DHCP IP Address and configs etc and registers to the WLC. It too is on Vlan 6 and it is connected to the 4506 on int gig 4/33 which is an access port. [code] I am doing local authentication, so i have added users to the WLC.. My problem is that the first client that connected was able to get an IP address and connect to anything internal and external.I then connected another client on another laptop and that client could connect but not get an IP address, it just self assigned.When i look at the clients i can see the MAC address of both Clients on the WLC, but doing a show mac address-table dynamic i only see the MAC of the client that works properly. The client that doesnt get an IP has no entry in the 4506 switch.I am stumped, from what I understand, is that the 2nd clients traffic is being trunked to the WLC , hence it has the MAC address. But I dont know why its not getting a DHCP assigned IP address.
View 37 Replies
View Related
Mar 8, 2009
I'm monkeying around with an 881-W. Clients can associate and authenticate to ssid 'test', but they cannot get a DHCP address. Clients plugged into f 0 - 3 get DHCP addresses just fine.
I've looked at a lot of different guides, ran debugs etc. When wifi clients make DHCP requests the server never gets them. So there must be some IRB thing going on.
View 5 Replies
View Related
Dec 13, 2012
I am setting up a new remote access VPN using the traditional IPSec client via ASA 5515-X runnning OS 8.6.1(5). We require to provide each client multiple DNS suffixes, but are only to provide a single DNS suffix in the group policy.I have tested using an external DHCP server, but using our Windows Server 2008 infrastructure and Option 119 the list is not provided to clients, and I have read that Windows 7 clients may ignore this option anyway.
View 0 Replies
View Related
May 30, 2011
I want to open a branch office but need to access the same server as in the main office.How do I do this without losing speed?
View 2 Replies
View Related
