Cisco Routers :: RV042 - Access Site 2 Resources Via QuickVPN Connection?

Nov 15, 2010

So here is my issue. I have two sites, each with a Linksys RV042 on thier site.
 
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
 
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
 
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
 
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
 
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
 
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.

View 6 Replies


ADVERTISEMENT

Cisco Routers :: RV042 - VPN Access Resources With Same Subnet?

Aug 24, 2011

I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).

View 1 Replies View Related

Cisco VPN :: RV042 - Cannot Access Resources With Same Subnet

Aug 19, 2011

I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).

View 1 Replies View Related

Cisco Routers :: RV042 QuickVPN Not Working For All PCs

Oct 21, 2011

So have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
 
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
 
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
 
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
 
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
 
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.

View 2 Replies View Related

Cisco Routers :: RV042 - QuickVPN Error

Mar 11, 2012

I've one RV042. I've configured VPN PPTP and it work (I've redirect port 1723 on router1 to rv042). If I can try to use quickVpn, client login and receive error "remote gateway is not responding". I have redirect port 60443 from router1 to rv042. Connection it's this: INTERNET-router1-RV042.

View 3 Replies View Related

Cisco Routers :: RV042 - Login Using QuickVPN

Sep 21, 2011

Today I purchased a RV042 wired router. I set the VPN connection but when I try to login using QuickVPN, get stucks in "Verifying network". I checked the logs:

2011/09/22 20:43:45 [STATUS]OS Version: Windows 7
2011/09/22 20:43:45 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/22 20:43:45 [STATUS]Windows Firewall Private Profile Settings: OFF
[Code]...
 
From my side Im connected to a WRT54G2. VPN Passthrough enabled. Windows 7 Pro x64. No 3rd party AV or firewall. Windows Firewall disabled, also tried enabling it.

From the RV042 side it has a Static IP Address configured. DHCP server enabled. HTTPS enabled. UPnP disabled. L2TP disabled.Firewall disabled. Block WAN Requests disabled.

View 6 Replies View Related

Cisco Routers :: RV042 QuickVPN / Gateway Not Responding

Jun 28, 2011

I have router Linksys RV042 v1.2 with latest firmware Version: 1.3.13.02-tm. And I'm using QuickVPN v 1.4.1.2. I've setup VPN connection with values, below: But every time I'm trying to connect to router by VPN it always popup a window "Remote Gateway not responding".It occurs when I'm trying to connect to VPN behind other router, when I'm connected directly to Internet the connection is established.But I'm connecting to other networks using VPN and it's working properly (behind the same router), so I think it's problem with RV042 configuration but I don't now weher.

View 5 Replies View Related

Cisco Routers :: RV042 Configuration With QuickVPN In Windows 7

Oct 1, 2012

I've been working on getting a client to Gateway configuration going for quite some time now.  Had it working with a different Cisco single wan router that failed.  The user replaced the router with an RV042 and we are trying to get the QuickVPN to once again connect to the router as it did before the replacement.  Previously we did connect successfully with Windows 7 clients.
 
Router: RV042 v3 firmware 4.0.4.02-tm Quickvpn version 1.4.2.1
 
what i keep getting in the log is the following :
 
2012/10/02 12:55:07 [STATUS]OS Version: Windows Vista
2012/10/02 12:55:07 [STATUS]Windows Firewall Domain Profile Settings: ON
2012/10/02 12:55:07 [STATUS]Windows Firewall Private Profile Settings: ON

[Code].....

View 5 Replies View Related

Cisco Routers :: QuickVPN RV042 V03 Some Users Connect Others Can't

Feb 10, 2013

A client of mine has a Cisco RV042 Router. I've configured it to run VPN and it works, sort of. Some clients can connect, others can't, for no discernible reason.

Specific machine issues are Windows 7 x64 or x86, Quick VPN latest release, unobtrusive (Avast or Microsoft Security Essentials) security, etc. 2 separate machines on the same home remote network, 1 can connect just fine, the other can't. My laptop (Win7 x64) connects just fine, one of my techs can connect OK, the IT support guy that works for this client can connect.
 
Particulars of the router: Firmware version: v4.0.4.02;  PID VID : RV042 V03;  Firmware MD5 Checksum :     1f84d8d0a2a8b99f9bfa4409e64547aa

View 3 Replies View Related

Cisco Routers :: RV042 - QuickVPN Versus Standard VPN Client

Nov 15, 2011

I have a RV042 router setup with Client to gateway VPN access, and am connecting with a W7 PC running QuickVPN. We have many PC's that already have the standard CiscoVPN client on them, is it possible to configure the RV042 to allow these clients to conenct? I'm not sure how to get the Mutual authentication to work, or how to import the PEM certificiate into that client. It seems to allow it to import, but I can never select it.

View 2 Replies View Related

Cisco Routers :: RV042 QuickVPN Loops While Verifying Network?

Nov 15, 2012

I used to have the problem where QuickVPN keeps on trying to verify the network because the RV042 cannot get the final ping to the client.I then bought a RV042 HW version 3 on the VPN side and I installed RV042's at the clients as well.This may look like overkill but believe me, it gives peace of mind, it made things a whole lot better, everybody happy.I am going to set up tunnels but for the time being the clients use QuickVPN. The above setup is all good if people access the vpn from the same source.
 
I now have a problem where one of our people is in Vietnam and she cannot access the vpn due to the "verifying network" loop.Looking at the log everything looks great, I compared a successful connect with an unsuccessful one and the logs are identical.The only difference is that the final ping is blocked (recorded in the QuickVPN log on the client side).The client uses W7 with firewall on.No need to repeat suggestions, such as turing printer sharing off, I have been through all that. isn't this simply caused by the ISP in Vietnam blocking pings ?

View 2 Replies View Related

Cisco Routers :: Quickvpn / Client To Gateway Vpn Rv042 Can Only Ping Router?

Jan 27, 2012

I am setting up remote access using an RV042 router.  Using quickvpn or a client-to gateway vpn and shrewsoft client,  I can only access/ping the LAN side of the remote router and one machine on the remote network.  The PPTP server and native Windows 7 connection provide access to all machines on the remote network.I have 2 possible reasons for this and would like to find the real reason:
 
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.

2)  The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.

View 2 Replies View Related

Cisco Routers :: Site-to-Site VPN - Configure It Between RV042 And 2911

Dec 29, 2012

Is there a way to set up a Site-to-site VPN between RV042 & Cisco 2911? I "googled" this and obtained a document, but it is not regarding Cisco 2911: [URL]
 
Routers are needed to setup it successfully. I have tried on both routers several configuration steps, no success...

View 3 Replies View Related

Cisco Routers :: RV042 - Site To Site VPN And Behind Juniper Firewall

Mar 25, 2013

I have no problem configuring both devices to successfully connect when the juniper firewall isn't in the picture.  But due to policy; the RV042 at our main site must sit behind the firewall.
 
I've got the port forwarding setup but I'm not able to connect.  I know I"m missing some configuration on the RV042 but I can't think of it! I've attached a GIF to give an example of both setups.

View 3 Replies View Related

Cisco Routers :: Site-to-Site VPN Configuration Between Two RV042

Apr 23, 2013

I have got two CISCO RV042 .I need to configure a site to site VPN .

View 1 Replies View Related

Cisco Routers :: RV042 Site To Site VPN With Dynamic IP?

Nov 28, 2012

I recently bought two RV042s to create a site to site VPN for a client.  I have several of these setups installed at other locations but this is the first version 3 hardware I've used.It seems like the dynamic IP functionality of the VPN setup may not be working correctly.  I've verified all settings on each router match and have deleted/recreated the setup several times just to make sure.  Here's the logs from the router with a static IP.
 
Nov 29 06:49:51 2012 VPN Log (g2gips0): deleting connection 
Nov 29 06:49:51 2012 VPN Log added connection description (g2gips0) 
Nov 29 06:49:51 2012 VPN Log listening for IKE messages 
Nov 29 06:49:51 2012 VPN Log forgetting secrets 
Nov 29 06:49:51 2012 VPN Log loading secrets from '/etc/ipsec.d/ipsec.secrets' 
Nov 29 06:49:51 2012 VPN Log (g2gips0): cannot initiate connection without knowing peer IP address 
Nov 29 06:49:51 2012 VPN Log (g2gips0): cannot initiate connection without knowing peer IP address 
 
I've tried both dynamic IP + email and dynamic IP + FQDN to authenticate the router using the dynamic IP and both give the same error as above.I did a firmware update hoping to fix PPPoE which seemed to be broken with a Netopia modem in bridge mode so both routers are on the latest firmware, v4.2.1.02. 

View 18 Replies View Related

Cisco Routers :: WRVS4400N Site-to-site VPN With RV042?

Oct 15, 2012

May I know can the 2 models WRVS4400N and RV042 perform site-to-site vpn with each other?

View 1 Replies View Related

Cisco Routers :: RV042 - Site To Site VPN Speeds

Jan 24, 2013

I have an RV042 connected to another RV042 via site-to-site VPN.  The tunnel has been solid for months, but when I did an actual read/write test between PCs at either endpoint, the speeds were quite slow.

Endpoint A has a line speed of 25/5.
Endpoint B has a line speed of 50/7-ish.
 
Read/write test from A to B was about ~3 write and ~7 read. Does this sound normal for these routers?  I was hoping for better performance than that.

View 1 Replies View Related

Cisco Routers :: Access LAN Resources Through WRVS4400n?

Apr 24, 2012

I am connected with qvpn, I can log in to the router bios remotely, but when I try to map the network drive from my remote location it does not work.I can detect the machine on the network, but it will not go further and tells me that "said IP was found but could not locate G". Does this mean it is behind a firewall on server side and that I need to create a rule to allow the incoming traffic? Or could it be something else.

View 1 Replies View Related

Cisco Routers :: RV082 Access Resources On RV016

Apr 29, 2013

I know this *should* be simple but having a devil of a time getting it to work.
 
I have 2 routers. Both have a static ip. Each is setup for a different private subnet. At the moment they are not connected to each other. Consider this setup (made up numbers obviously):
 
RV016
has 13 lan ports, 2 internet ports, 1 dmz port
Internet port: 10.10.10.10

[Code].....
 
I'd like clients on the rv082 lan to be able to access the printer on the rv016 lan, and use the rv016 as an alternate internet connection (optional). I would prefer the rv016 client not be able to access the rv082.

View 3 Replies View Related

Cisco Routers :: Setting Up Vpn With RV 120W Cannot Access LAN Resources

Oct 12, 2011

I managed to set up an ipsec vpn between  the RV 120W (responder)  and Shrewsoft vpn client.The virtual ip and dns for the client pc are manually set. The tunnel is enabled, but I see no traffic between the local and the remote LAN.I can't ping or reach any pc behind the router.Using the command ipconfig /all on the client pc, I see that no gateway is assigned to the virtual vpn interface.So it seems that the RV 102W is unable to pass to the client the address of the default gateway for the lan, and I think this is why I can't access any resource.

View 4 Replies View Related

Cisco Routers :: RC120W Setup For QuickVPN Connection

Aug 10, 2010

I did upgrade to WiSM from v5.1 to V6 then i see this log %WCP-3-KEEPALIVE_LOST: wcp_controller_server.c:1763 Lost keepalives from Cat 6K Supervisor.

View 6 Replies View Related

Cisco Routers :: RV180 Configure VPN Connection With QuickVPN?

Jun 4, 2013

I have a doubt. What I have to configure in my RV180 to make a VPN connection with Qvpn client. I created the user and if try to connect from the client I've recieved the message that is connected, but if I try to ping the RV180 local ip answer, but if I try to ping any other IP address of the VPN I can't. I think I would have something misconfigured but I don't know what is it.

View 4 Replies View Related

Cisco Routers :: RV042 Killing Off Site Backup After About 2 Hrs

Dec 23, 2011

I have 16 customers using RV042 router all 11 have the RV042 router different ISP's. After eleminating every thing else we were down to the routers. Two of the customers we built linux boxes to do the routing and firewalling and VPN, etc. Once in place the problems went away. Which confirmed it was the RV042 router causing the problem.
 
We watched the traffic and after about 2 hrs the router tells both ends to reset. End of communication.
 
My question is how do we stop the router from terminiating the connections. They are not bandwith hogs. They are nessessary connect connections. 

View 3 Replies View Related

Cisco Routers :: RV042 Site VPN Behind Cable Modem

Oct 23, 2012

Having some issues getting a site to site VPN connected between two RV042. Any experience getting this to work behind a Motorola SBG9000.Will I be able to get this working? Or will I have to organise a cable modem through my ISP instead

View 1 Replies View Related

D-Link DIR-825 :: Cannot Access Remote Network Resources After VPN Connection Is Established

Oct 22, 2009

After I change my router, I recently found out that I cannot access remote network resources after VPN tunnel is established. I use CISCO System VPN client. I can see the connection is successful. I cannot ping server on the remote network

View 2 Replies View Related

Cisco Routers :: QuickVPN From One RV220W To Other - No Webpage Access?

Dec 19, 2011

Using QuickVPN from one RV220W to another RV220W I cannot access the Webpage of the remote router.  Goes to "CERTIFICATE NOT VALID" then click through that, and the the login page will not come up.  Sceen flashes a hint of blue background, then turns white, then just sits there saying "Waiting for response from ???.???.QuickVPN will sucessfully connect and I can use all computers behind the router.  Just cannot access the Webpage of the remote router.  I can access the Webpage of the local router.Also, when I hookup using QuickVPN from an "Internet Cafe" that is using a Netgear router.  I can then access the webpage on both remote routers (of course, depending on whom I QuickVPN'd into at the time).
 
Location #1
Office #1
RV220W:  RV220W-A-K9-NA    SER: SER15140314Firmware:  1.0.3.5
IP: 192.168.63.1
 Location #2
Office #2
RV220W: RV220W-A-K9-NA SER: SER151600R2
Firmware: 1.0.3.5
IP: 192.168.2.1
 
I have called Cisco on this with no luck.  They said to update my JAVA.  I am currently JRE 6 Release 30 and still no luck.  The Log files reveal nothing and are darn near unreadable since there is no line breaks in the log file.  Have to manually edit the log to pick stuff out.

View 1 Replies View Related

Cisco Routers :: RV016 Firewall Is Blocking QuickVPN Access?

Feb 16, 2012

We have had our router and remote computers set up with Quick VPN for over a year. We've had our share of problems but have worked around them.
 
Now, out of the blue, no one can connect to the VPN. I went in to try to do some 'troubleshooting' and the ONLY thing that allows our VPN connection to go through is to completely disable the RV016 firewall. We have too many remote users to actually start and stop the firewall everytime someone needs the VPN connection.

View 1 Replies View Related

Cisco VPN :: QuickVPN - Gateway Not Responding - RV042?

Oct 28, 2011

I'm running Cisco QuickVPN on a clients laptop (Windows 7). Windows firewall is disabled because McAfee SaaS is running.I sometimes have the issue that the initial connection attempt comes back with "Gateway not respoding" during the network verification process. You close the program, you open it again and it works. Sometimes it takes 2 or 3 tries. Today I have the issue that my client tried it like 20 times including several reboots and it's just not working. I tried it from my own computer and it connected fine on the 2nd try.I'm thinking that it might be time-out thing, that the VPN client doesn't receive a response fast enough? I know my clients home internet is darn slow.

View 1 Replies View Related

Cisco Routers :: RV220W Site To Site Vpn And Internet Access From Single Ip?

Dec 18, 2011

Can I use a single Public IP address for both Internet access and site to site vpn access?If not, can I configure the RV220W as a bridge and still use it via another gateway configured for vpn passthrough as a VPN appliance/server on the LAN?

View 3 Replies View Related

Cisco Routers :: RV180W Site-to-site VPN And Client Access?

Feb 9, 2013

I am considering to buy two RV180Ws and place them on two separate locations. But before buying I would like to make sure that the units meets my requirements. Lets call the locations A and B. I would like to connect location A with full network access to location B. But at the same time I would like to have that location B also gets full access to the network at location A.Besides this I would like to be able to connect to one of the networks from remote with my laptop.Preferably all connections should be made using IPSEC and not PPTP.I would like to know if it is possible to make such a configuration, and eventually if there is a smarter way to do e.g. only letting clients connect to location A or B and granting them access to all ressources at both location A and B from there.

View 1 Replies View Related

Cisco Routers :: RV180 Restrict Access To Site-to-Site VPN

Feb 21, 2013

I am trying to configure my network so that VPN traffic is only routed to a single physical port on the RV180 or to a certain subset of devices on a network.
 
I have a site-to-site vpn setup in a home office and am connecting to the corporate network.  The user has a couple of devices running on the home network that need access to the corporate network.
 
We are hoping to leave his PC accessible to his home network as well as the corporate network, but restrict other devices from accessing the vpn.
 
I beleive I could do it by playing with the subnet but I can't get my head around it.

View 8 Replies View Related

Cisco VPN :: ASA 8.2(1) / ASDM 6.2(1) - Site-to-site Connection Creation Broke AnyConnect Access

Feb 7, 2012

ASA = 8.2(1)
ASDM = 6.2(1)
 
Recently I used the wizard to create an IPsec site-to-site connection, which went very smoothly; however, I now noticed that when I connect via Anyconnect 2.5.0217 I cannot get to local and subnatted resources on the network.
 
I rolled back to saved config file, which was taken before the site-to-site vpn was created, but that did not work as well.What should I check to see why I can no longer get to different subnets after the site-to-site vpn connection.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved