I have 2 VLANs set up and I know they are set as default to not allow one to communicate to the other. Is there a way to set a rule to allow that? I'd like VLAN1 to be able to access VLAN2, but not the other way around.
View 1 Repliesthe attached image shows what i am trying to achieve.i need to establish connectivity from subnets 10.30.5.X and 10.30.6.X (in VLAN1 and VLAN2 respectively) to subnet 10.11.35.X
i have a trunk port on my cisco 2960 that is connected to GiE0/0 on my Cisco ASA that has 2 sub-interfaces with IPs in the subnets mentioned above.my problem is i can only connect to 10.30.6.X from 10.11.35.X (and vice versa), but no connectivty to 10.30.5.X
I am trying to setup a VPN using an RV042 (fw ver: 1.3.12.6) to access a VISTA computer over the internet using a laptop using QVPN's latest version. I finally got it to connect but then hang's with error " Gateway is not responding, do you want to wait?". If I say yes it go through the login again and hangs. If I say no, it hangsup. I've tried a couple different ideas using tunnelling and static IPs in the router but nothing. All I want is to be able to access one computer through the RV042 over the internet from any other computer using the QVPN.
View 6 Replies View RelatedWindows Server 2008 R2 has two DHCP scopes 192.168.1.x (for data) and 192.168.2.x (for VOIP). The Catalyst 2960-S has Vlan1 for the Data V LAN and V lan 2 for the VOIP network. How do I setup DHCP relay for Vlan2 to get their IPs from the scope on the Windows server?
Used to doing ip helper-address x.x.x.x in other Catalyst switches, but not available here.
I am trying to setup the following. We have an RV042 Router and are using it as our gateway at the office. In the office we are using a Windows Domain abc.lan with DHCP of 10.0.0 - 10.0.0.254. The Router/Gateway is setup with a Static IP of 10.0.0.100.A couple of our office employees would like to work from home via VPN using their laptops. With the many options available for this router, I am not clear as to which options and what settings I should set.
View 2 Replies View RelatedI need DHCP Option 66 to be enabled my small business RV042 router, so the IP phones could know where is the TFTP server.
View 1 Replies View RelatedWe are currently running Windows 2003 Domain in our network with DHCP turned on the Server. We have turned off the DHCP on the Router. We are using RV042 as out Gateway to the internet and everything is working fine. We would like to allow a couple of our users to be able to VPN into the network so that they can use Outlook and be able to access their files on the Shared Folder. The users would be using their laptops from their homes to connect via VPN using the standard Windows 7 VPN connection.
In the RV042 Interface there are many options and I am not sure I understand which setting would allow them to connect successfully to the network, be authenicated as a domain user.
I am trying to set up my rv042 to use the ddns service. The rv042 is directly connected to the ISP provided modem on WAN port 1. The problem is that instead of seeing the internet IP the rv042 is using the ISP sub net assigned IP.
LAN IP : 192.168.1.1 WAN1 IP : 192.168.12.9 WAN2 IP : 0.0.0.0 Mode : Gateway DNS (WAN1) :DNS (WAN2) : 192.168.12.1 DDNS(WAN1 | WAN2) : Off | Off DMZ Host : Disabled
I am trying to configure a Linksys RV042 VPN router as a simple router. I want to connect it to one of the ports from a CiscoASA5505 router because I need to connect 4 additional PC's and the ASA is out of available ports.I am trying to connect it through an ethernet port from my laptop.At first I configured the TCP/IP settings as getting the IP and DNS's automatically and but I was able to enter the setup by entering the default IP address (192.168.1.1).After 10 minutes it got disconnected and could not connect again.I get Status: Limited or no connectivity.If I try to type the IP address manually (192.168.1.1) I can ping the router successfully but the setup webpage never opens.what I need to do in order to access the setup webpage when I connect the router directly to my laptop?
View 10 Replies View RelatedI have a customer with several SG300's providing VLAN1 for data and VLAN10 for voice. The PC's are piggy backing off the phones and showing up in the SG300 fine:
One department has recently employed more people so we have an SG200 switch to connect the computers and phones to. I don't seem to be able to get any connectivity between the new switch and the SG300 it is connecting to. I have setup VLAN1 and 10 as per the images below:
I am trying to set up my router to grant http traffic a minimum bandwidth of - for example - 5,000 kBit (if there is any http traffic).
So I set http min. rate to 5,000 while I set nntp min. rate to 1 However, when I run nntp downloads on several connections (e.g. 10) my single http download never goes above 1,000 kBit. Without any other connections I reach 8,000 kBit.
I am using a single 12 MBit line.
I have a RV042 router and we are trying to set-up our OWA for outside access. I can't figure out which ports or which page those ports are on to open them. We are a small company and we do not have IT except for ourselves. The internal network works fine but i can't get the Exchange access from outside.
View 2 Replies View RelatedMy plan is to use VLAN1 for the internal private network and VLAN2 for free public wifi. My question is can I use a PC on VLAN1 to configure/manage my access points? There are no dedicated PCs on VLAN2.
View 7 Replies View RelatedI have been trying to resolve this issue with only allow facebook access throug the content filter between 12pm and 1 pm. However The settings never seem to take. Is this a bug in the system? If I start the filtering from 1300 to 1200 that should allow facebook to be accessible only on lunch.
View 2 Replies View RelatedI am trying to access my RV042 through telnet. I go to http://192.168.1.1/sysinfo123.htm?ConsoleSimulation=1
which enables telnet. However when I type my username and password it will not authenticate.
I am new to implementing VPN service. What I would like to do is install a RV042 or RV082 (for added speed) and configure it to allow me to access the Internet (from home base) through the VPN from any location while on the road and using my laptop. My questions are: Can this be done? If so, what needs to be done in the configuration to allow gateway access to the Internet? I can't find any reference in the Cicso documents, but somewhere I saw that it can be done. I don't care about accessing anything on the local LAN. As I would be using the same Internet connection for the VPN and the access to get out----how would this affect speed? I plan to use Quick VPN as the client, and haven't even touched the client issue.
View 5 Replies View RelatedI had this problem where 2 users could only access my RV042 vpn one at a time
The Linksys solution was to give these 2 users a RV042 as well. That worked, 2 can access my vpn at the same time. We use QuickVPN for this purpose
But now there users cannot access another Cisco vpn any more in our office. I attach a schematic and a screen shot of the error when trying to connect to the professional vpn with vpn client version 5.0.07.290
The 2 notebooks epresent the 2 users
The one at the bottom is my vpn
The connection on the left is the professional vpn
We now use remote desktop to my vpn to get to the professional vpn, that work but we don't like it
I configure my new purchase RV042 router, in Access Rule i Deny all services the source is Lan and destination is WAN. my concern is i want to allow LAN to access internet, so i'ved create another rule which allow http, https. but my problem is i cannot access internet.
View 4 Replies View Relatedbrand new RV042 client (tried MacOS and Win7 on two laptops) will get IP from DHCP and shows correct IPs for gateway etc. - however entering the IP 192.168.1.1 to access web admin does not work (tried current versions of Firefox, safari and Firefox); browser is not offline router was reset to factory setting (by pressing reset for over 30sec) ping on IP above works
hardware broken?
I've setup a GroupVPN and connect to the RV042 with the Shrewsoft VPN client, works like a charm as opposed to QuickVPN ;-)The firewall is configured with an explicit deny rule for RDP access to an internal server, also an explicit allow rule is created for certain IP numbers as source. I noticed that I need to create an explicit allow rule for the subnet the Shrewsoft client is using for the virtual adapter or I will not be able to access the internal server via RDP through the GroupVPN tunnel. I would think that setting up a tunnel defies the rules created for direct access on the WAN port.
View 5 Replies View RelatedI have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies View RelatedVery recently, we had implemented Site-to-Site VPN tunnel between two Linksys RV042 4-port VPN routers. Everybody in our remote site is accessing and sharing the data through this tunnel and it is working fine.
Now, we have a plan to implement the same for our mobile clients also. For this, we had followed all the basic configuration procedures and user got connected to Quick VPN tunnel. Here is a problem we had observed. The mobile client user is connected to the tunnel, but unable to access the office LAN from the PC.
I am trying to limit HTTP access to my server on the local network to a specific IP address. I create an Access Rule in the firewall section, however that doesn't work. The only way it works is if I add the internal IP address of the server to the Forwarding section where I create a new HTTP forwarding rule.However, that is not good because that allows ALL HTTP traffic to that server instead of just by the single IP address.
View 2 Replies View RelatedI've installed RV042 for a client of mine. For next two months everything worked without any problems. The issue I've been experiencing lately is when I assign a static IP address to the PC it won't have internet access. Once I allow it to have a dynamically assigned IP then it works fine. The IP I assign isn't part of the DHCP range.
View 7 Replies View RelatedI wanna block the Lan IP address(eg:192.168.2.106) to visit wan web, and allow it to lan.How can i set it in access rules?
View 2 Replies View RelatedI have a RV042 and have set it up for VPN Client access using the QuickVPN client to connect my remote users. I discovered today that I cannot have two users connect in at the same time. Both users are in the same remote office. They can connect individually with no problem but if one is connected and the other tries connect also the second user gets a message the gateway is not responding. They are both running Win XP PRo SP3.
View 1 Replies View RelatedSo here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
I have configured PPTP Server on RV042, and created 3 accounts. I am able to connect from Windows PC without any problems.
In the router's logging utility, there doesn't appear to be any log entries indicating either successful or failed attempts to connect to PPTP server. The only access logs I see are for access to the router's configuration utility. Is there a way to view PPTP access in the router system log?
We have RV 042 deployed for internet access/firewall purposes. Due to growing number for Wireless devices and also to separate WLAN traffic from wired devices, we have created a separate VLAN/IP Subnet for the wifi devices. We are having trouble accessing the internet from the WiFi VLAN/IP Subnet. Cisco 3750 is layer 2 and layer 3 device. We have VLAN 1 (10.10.10.0/255.255.255.0), all wired devices and RV 042 are part of VLAN 1. Connectivity to internet from VLAN 1 is good. VLAN 2 (192.168.1.0 / 255.255.255.0) was created for wifi devices, 3750 does the inter-vlan routing, I have enabled the multiple subnet feature on the RV 042 and added 192.168.1.2 / 24 to the subnet list, we still have issues accessing internet from vlan 2 devices.
As a workaround, I shutdown vlan 2 and added 192.168.1.0/24 as secondary address to the VLAN 1 interface on 3750 and i was able to access internet from 192.168.1.0/24 network with wifi devices also on vlan 1, we want wifi devices to be on separate vlan / ip subnet. Looking at the documentation for RV series routers, it talks about supporting multiple subnets access to internet by enabling multiple subnet feature but it doesn't seem to work.Are there restrictions on having multiple vlans?
I have a RV042 and have set it up for VPN Client access using the QuickVPN client to connect my remote users. I discovered today that I cannot have two users connect in at the same time. Both users are in the same remote office. They can connect individually with no problem but if one is connected and the other tries connect also the second user gets a message the gateway is not responding. They are both running WinXPPRo SP3.
View 4 Replies View RelatedI attempted a firmware upgrade on my RV042. After an hour, the upgrade was still in progress. I now cannot login into the router using my user name and password (nor the old admin/admin). The router is functioning, but I fear it will eventually fail. How can I recover ability to log in? The Firmward Recovery program doesn't seem to be appropriate for this situation.
View 3 Replies View RelatedI have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies View RelatedI am trying to setup internet access and intranet access using two cards per PC. I don't have sever software and I want to be able to share files between several machines. I have two routers. One that connects to cable modem and one that connects to intranet side. I have assigned different static ip addresses to both cards.
View 6 Replies View Related