Cisco Routers :: RV042 - VPN And Admin Login Stopped Working

May 16, 2012

My organization has deployed 3 Cisco RV042 (v3) at our 3 sites. They have been working pretty well up until about a week ago. One of them continues to route traffic and perform port-forwarding, but the VPN has completely stopped working and I can no longer access the web administration interface. I get the standard login page, but any attempt to login (with correct or incorrect password) takes maybe 5 minutes with a spinning status icon, followed by a blank page leaving the browser at: url...
 
I have the router logs e-mailed to me, and I can see that the system boots up with Jan 1 2010 as the system date, but it eventually gets the correct date from NTP, so I'm doubting this is causing the problem.
 
These were working for months prior to this happening, and even a reboot of the affected RV042 does not allow me to log into it or setup the VPN tunnels. I have found similar threads on this forum: url...

View 2 Replies


ADVERTISEMENT

Cisco Routers :: RV042 1 To 1 NAT Stopped Working

Jan 6, 2012

I've had 1 to 1 NAT setup for years now with no issues and the other day it simply stopped working.  Rebooted everything, had ISP clear arp on their cable modem yet nothing going.  As soon as I remove the 1 to 1 NAT on the router the PC has internet access.  Add the 1 to 1 back and no out going internet.  The configuration is pretty basic and has not changed.Thinking it could be a hardware issue I swapped it out with another RV042 I have with the exact config, same thing 1 to 1 NATs have no internet access.  Upgraded one of the RV042 firmware to Firmware Version: 1.3.13.02-tm, had cable modem replaced, spent numerous calls with ISP.  nada
 
I have found one interesting thing however, any internal machine which is set to dhp works fine, and static ip that does not have a 1 to 1 nat works fine and the last ip in the 1 to 1 nat range works fine.  If I extend the range it is always only the last ip that works.  Even if I add 1 to 1 nats one line at a time, it is always the last entry that works..

View 4 Replies View Related

Cisco Routers :: RV042 After Configuring DMZ / Remote Management Stopped Working

Sep 30, 2012

I have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:

- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
 
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.

View 2 Replies View Related

Cisco Routers :: RV042 - Access Web Admin

Jun 12, 2012

brand new RV042 client (tried MacOS and Win7 on two laptops) will get IP from DHCP and shows correct IPs for gateway etc. - however entering the IP 192.168.1.1 to access web admin does not work (tried current versions of Firefox, safari and Firefox); browser is not offline router was reset to factory setting (by pressing reset for over 30sec) ping on IP above works
 
hardware broken?

View 3 Replies View Related

Cisco Routers :: RV042G Site Certificate Invalid On Admin Login Page?

Aug 17, 2012

I recently replaced my RV042 with an RV042G.  I did an export of the RV042 Config and used the Config Migration Tool to upgrade the file to v3 (I had an old v1 RV042).  When I first logged in to the RV042G it was quite happy and I imported the config file successfully.After installing the RV042G in my system it fired up and worked perfectly.  Unfortunately when I now try to log in via the web interface it comes up with 'Invalid Site Certificate' each time. I've tried importing the certificate but that does not work as it is flagged as invalid.All I can assume is I have either imported the origional RV042 certificate as part of the config or importing the config has corrupted the original RV042G site certificate.  I assume this is a generic issue and not specific to the RV042G as I have had this problem before but cannot remember how I solved it.The bottom line would be a hard reset and load all my settings manually but I can't spare the time just now.

View 2 Replies View Related

Cisco Routers :: RV042 - Login Using QuickVPN

Sep 21, 2011

Today I purchased a RV042 wired router. I set the VPN connection but when I try to login using QuickVPN, get stucks in "Verifying network". I checked the logs:

2011/09/22 20:43:45 [STATUS]OS Version: Windows 7
2011/09/22 20:43:45 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/22 20:43:45 [STATUS]Windows Firewall Private Profile Settings: OFF
[Code]...
 
From my side Im connected to a WRT54G2. VPN Passthrough enabled. Windows 7 Pro x64. No 3rd party AV or firewall. Windows Firewall disabled, also tried enabling it.

From the RV042 side it has a Static IP Address configured. DHCP server enabled. HTTPS enabled. UPnP disabled. L2TP disabled.Firewall disabled. Block WAN Requests disabled.

View 6 Replies View Related

Cisco Routers :: RV042 Cannot Login To Web Administration After First Logout

Feb 2, 2009

we are using Cisco RV042 router with i guess V3 hardware version, latest driver version (4.2.1.02). We changed the username and password from admin, default, to another name and password. Since then, we are able to log in only once, once the router is restarted. If we leave the page, logout or after several hours after boot, we wont be able to log to web administration again. We enter username, password, submit, the image keeps spinning, but nothing happens.

View 5 Replies View Related

Cisco Routers :: RV042 Web Utility Screen Goes Blank After Login?

Feb 1, 2012

I'm running a new RV042 with the latest firmware (4.1.1.01).  I set it up about 2 weeks ago and have been running it without an issue.  Today I tried to go in to the web utility to make some changes.  I was prompted for the userid/password, which it appeared to accept (if I typed in the wrong ones it rejected it), and then the screen went blank (normally I would get the status screen now.)  Instead the screen I get is the light blue of the log-in screen, but there is nothing on it.  The router has switched to the page https://192.168.1.1/home.htm  I have tried different browsers and accessing it from different computers - the situation is always the same.  I have power cycled the router, and there is no change.  I suspect the next step is a manual reset to factory defaults - but of course I would rather not (as I didn't save all my settings of course!)

View 2 Replies View Related

Cisco Routers :: RV042 Main Login Password Has Expired

Mar 1, 2013

my RV042. The main login password has expired but it will not let me change it at all. Basically I try to login but get the error 'The old password has expired. Please change the password'. But with no prompt at all for a new password and just a return to the login page. Tried various different browsers, tried the old default password but nothing will work. There seems to be no way of changing it and I cannot login.
 
I really don't want to reset it to default as I have numerous VPN tunnels configured and various other settings.

View 5 Replies View Related

Cisco Routers :: RV042 / Login Screen On WAN Address With Remote Management Disabled

Aug 28, 2011

My first try at configuring my RV042 has had unexpected results. I set a WAN and LAN address, but did not enable remote managment and did not configure any port forwarding.  I expected to be able to connect to the router on the LAN and I could. The surprise came when I put in my web address.  I got a router login page.  How do I suppress than on the WAN side.  I have a static address with my ISP.

View 1 Replies View Related

Cisco Routers :: WRVS4400N Stopped Working With VOIP Phone

Mar 1, 2013

I have the router for over two years, Present Firmware is V2.0.1.3, I have Polycom phone connected to the router using 8 x 8 VOIP service. The phone was working fine untill yesterday. 8 x 8 tech support suggested getting a different router. I have the same router at home and tried the same phone on my home router - it worked. So, the problem is not the phone but int he router. I tried to call Cisco tech support but found out that the warranty support expired and I need to buy a support plan. Called to buy the support, and gave up after an hours on hold. Left  message.

View 1 Replies View Related

Cisco Routers :: Linksys WRP400 Router Has Stopped Working

Dec 20, 2010

My Linksys WRP400 router has stopped working. power led blinks red and orange - phone led 1 and 2 light green - wifi connection not work - ethernet LAN connection not work - ethernet WAN connection not work - router now work in bridge mode - factory reset using Reset switch not work - connected analogue phone not work I try dump traffic using ngrep on LAN and WAN port but no packet comes from the router.

View 2 Replies View Related

Cisco Routers :: Configure Two RV042 Working Together

Dec 8, 2011

I tried to configure two RV042 working together. [code] WAN2 of both Router1 and Router2 are unused (unplugged). However, the Host2 can never ping to Host1. So as to Host1. Should I need to configure the protocol binding for all the traffic to the WAN1?

View 3 Replies View Related

Cisco Routers :: RV042 QuickVPN Not Working For All PCs

Oct 21, 2011

So have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
 
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
 
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
 
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
 
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
 
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.

View 2 Replies View Related

Cisco Routers :: RV042 Not Working For Backup

Jun 21, 2012

Updated to newest firmware 4.2.1.02 and wanted to perform a backup of the startup configuration.  I get a "The webpage cannot be found" HTTP 400 error when trying to do this backup.  I have changed some settings since my last backup, but that backup was done using the last firmware revision.

View 3 Replies View Related

Cisco Routers :: RV042 Load Balance Not Working?

Apr 16, 2012

I have set up an RV042 v1 and v3 both in Load Balancing mode.  Set in Router mode.I want one of the WAN ports to be preferred so I added a static route to 0.0.0.0 metric 5 to that WAN.Sometimes the route shows in the routing table and sometimes it goes away!!

View 2 Replies View Related

Cisco :: LMS 4.2 Admin Username Cannot Login

Oct 14, 2012

I have installed LMS4.2.2 on Windows 2008 server and am unable to login via the 'admin' username. I get "Invalid Username or Password. Please try again" error message. I can successfully login using Windows AD username and password.
 
 I have reset the password for 'admin' username with the following:
!
nmsrootinperl.exe resetpasswd.pl admin
  
Server has been rebooted PRE and POST password reset.

View 2 Replies View Related

D-Link DIR-601 :: Can't Login As Admin

Jan 6, 2013

i'm having some trouble logging in as admin. I leave the password section blank as directed but it comes up as "incorrect password".  I then tried the same using the "User" and it worked just fine but i cant change any of my settings. 

View 6 Replies View Related

Cisco Routers :: RV042 Stops Working During Long Transmissions

Apr 1, 2012

When my RV042 is accessed for long transmissions (svn check out, usually after 20 minutes ) the client receives a message "Gateway not responding, do you want to wait".
 
When this happens I see the following in the RV042 system log (the first 3 lines of the log below are normal):
 
Apr 2 17:36:53 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection

[Code]....

View 10 Replies View Related

Cisco Routers :: RV042 Does Not Load Web Interface / VPN Stops Working?

Aug 12, 2011

We bought an RV042 at the end of June. It is used as a gateway and VPN router. DHCP server is disabled and all IPs are configured manually.Every once in a while (Tuesday night, then Friday night - yesterday, it has hapened once or twice before that) the router appears to restart (see log below) then comes back up with system time of Jan 01 2010. At this point the router will no longer load its configuration page (https://10.29.238.197:16443/) and VPN connection to our customer in Africa drops. However, devices behind the router can be reached and can access the internet. The only way to fix this is to power cycle the router at which point everything starts working flawlessly again.The PID VID is RV042 V03 running firmware v4.0.3.03-tm (May 12 2011 21:27:37). Our RV042 is a newer one with Cisco SMB Router branding not the older Linksys branding.
 
From the log when the router reboots:
 
Aug 12 22:38:42 2011VPN Log(g2gips0) #141: retransmitting in response to duplicate packet; already STATE_QUICK_I2Jan 1 01:00:05 2010System Logheart : System is upJan 1 01:00:13 2010System LogWAN connection is up : 10.29.238.197/255.255.255.192 gw 10.29.238.225 on eth1Jan 1 01:00:15 2010VPN Log(g2gips0) #1: [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet 
 
I looked at the log more and all the usual messages assosciated with VPN being established are there - the last thing in the log before the router coming back up again is:
 
Jan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: sent QI2, IPsec SA established {ESP=>0x575a01c0 <0x6534ae4e 
 
So it even claims the tunnel should be up but I can never reach anything on the far side.

View 3 Replies View Related

Cisco Routers :: RV042 Load Balance Not Working Correctly

Feb 8, 2012

We have an RV042 on firmware version 1.3.13.02 and 2 ISPs:
 
WAN1 = Telepacific T1
1.5Mbps down and 1.5Mbps up
 
WAN2 = AT&T U-Verse
12Mbps down and 5Mbps up
 
I have it set to Load Balance, Primary WAN = WAN2
Network Service Detection enabled, only pinging the Remote Host of 4.2.2.2 and set to Generate Log
 
Bandwidth is set to:
WAN1 = 1000Kbps upstream & downstream
WAN2 = 5040Kbps upstream & 12000Kbps downstream
 
It seems to pick WAN1 a lot of the time.  Do I have something setup wrong?

View 12 Replies View Related

D-Link DIR-825 :: Can't Seem To Login Into The Admin Console

Mar 12, 2013

I wanted to update the F/w on my rev b dir 825, but unable to load the login console for admin, I haven't changed anything and the router was still on 2.07NA f/w

View 1 Replies View Related

Cisco Routers :: RV042 Set Up In Dual Mode And Both WANs Are Working Properly

Dec 23, 2011

I have my RV042 set up in Dual WAN mode and both WANs are working properly.  I would like to configure WAN1 to handle all traffic, unless it fails and then have everything to go to WAN2.  Pretty much what Smart Link Backup does, however with that enabled only 1 of the WANs is live at any given time.  I'd like both WANs to always be live as I'm going to see the second one as a back-door into the network.  Is this possible to do with routing?  I tried setting a routing rule to have everything to go WAN1, but when WAN1 goes down, nothing is rounted via WAN2.

View 0 Replies View Related

Cisco Routers :: Working Configuration To Connect IPad VPN-client To RV042

Nov 11, 2010

Any working configuration to connect the iPad VPN-client (IPSEC) to the RV042?

View 16 Replies View Related

Cisco AAA/Identity/Nac :: Banner For ACS 5.3 Admin Login Page

Feb 20, 2012

Is there a way to put a login banner on the ACS admin web page?  Either display it directly on the web page or do a redirect to a banner page?  Can I edit the admin pages directly or does ACS provide a mechanism to add this type of feature?
 
We are using ACS 5.3 running on VMWare.

View 2 Replies View Related

Cisco Routers :: RV042 Port Forwarding Stops Working When Firewall Is Enabled

Jun 4, 2013

I have a RV042 router on a single WAN and an internal LAN. I have configured port forwarding as follows: HTTP[TCP/80~80]->10.0.0.6HTTPS[TCP/443~443]->10.0.0.6IMAP[TCP/143~143]->10.0.0.5IMAP SSL[TCP/993~993]->10.0.0.5SMTP SSL[TCP/587~587]->10.0.0.5
 
Everything works just fine when I have the firewall DISABLED. However, when I enable it the behaviour is erratic. 1 out of 10 attempts to connect to ANY port forwarded works. Almost all attempts time out. Notice that this happens even if using only the default firewall rules (which should be bypassed by the port forwarding as I read in other posts).
 
My second try was to create firewall rules manually, overriding the default ones. I tried adding rules from source WAN1 (where my connection is) to ANY and to SINGLE IP's on every port. Nothing seems to work.
 
I don't know what I'm doing wrong, this is really bugging me. I had to turn the firewall off so we can access our servers from outside the office. This shouldn't have to be done.
 
Just found out that my firewall is getting LOTS and LOTS of Blocked - SYN Flood entries. I think this is why we are having trouble with the firewall. Could this be the problem? I have no idea where all these SYN packets are coming from since they appear with spoofed IPs or come from different bots all over.

View 1 Replies View Related

Linksys Wireless Router :: EA6500 Admin Page Hangs On Login?

Feb 3, 2013

I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.

View 9 Replies View Related

Linksys Wireless Router :: WRT610N - HTTPS Secure Login To Admin Page?

Mar 29, 2013

I am trying to log into my WRT610N version 2.0 Router  admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router.  Perhaps the router needs new firmware update to handle this with the latest browsers?

View 6 Replies View Related

Internet Stopped Working

Jun 1, 2012

My internet stopped working all of the sudden on my 2nd computer my 1st computer works fine (using atm) my 2nd computer stopped working all of the sudden it worked fine for about 2 years but the internet just went off for some reason it shows a computer with a yellow triangle with a black exclamation point on the bottom right corner it says connected but with limited connectivity ive tryed everything i know it is a windows XP i even bought a new internet cable today and the computer still does not work im new to these forums.

View 1 Replies View Related

Cisco VPN :: AnyConnect With ASA 5505 Stopped Working

Sep 26, 2012

I was installing a IIS server to our client and created access - rules for http server and port translations. After that i noticed i lost local lan access trough vpn.  Anyconnect and ipsec vpn. No other changes made to asa than those access-rules and nat changes. I'm trying to find out what is wrong, vpn connects okay, i can ping ASA but nothing else on inside network (for example dns server). Dns is not either working. When i ping local server, i can see in log.

View 8 Replies View Related

Cisco Firewall :: SSH Stopped Working On ASA5520?

Mar 27, 2012

I can no longer SSH to a primary active firewall. It had all of a sudden stopped working.  However I am able to SSH to the secondary standby firewall without any problems. I did try to regenerate the RSA key on the primary fw, but still unable to connect. The only way I can connect to it is by using telnet.
 
I ran the "show asp table socket" command and I'm seeing port 22 listening on the primary IP address (not the standby), foreign address is 0.0.0.0:*. I did a packet capture on port 22 on the inside inside, seeing my request hit the fw and then right away a reset back from the fw.
 
version 8.2.(5)
model ASA5520
 
I'm hitting a bug in the software version I'm running? Or what else can I check before rebooting the primary fw?

View 6 Replies View Related

Cisco WAN :: 2500 Router Stopped Working

Dec 13, 2011

it stopped booting up and now i cant talk to it.

View 5 Replies View Related

WG111v3 Stopped Working On Windows 7

May 25, 2012

I have tried a lot of drivers and even tried installing Vista 64 bit drivers (something that worked for someone in some thread), but it won't work.The adapter is recognized by the computer, but the smart wizard won't launch.
[code]...

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved