Do Cisco recommend me running the latest firmware update? Im just an individual who uses it for like a small web-/FTP-/Mail-server, etc. What are the recommendations? Personally I would have updated to the latest...but what are actually the Cisco recommendations?
View 3 RepliesI have an old RV082 with firmware version 2.0.0.19. I want to replace it with a new RV082 firmware version 4.0.2.08.I exported the fv2 config but can't restore it on the fv4. I get "invalid file type" error. The fv4 box is looking for a .config file and the fv2 box saves as a .exp file.
View 4 Replies View RelatedI have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies View RelatedI have upgrade the firmware on several RV082 (and RV042) model routers, and all of them have had subsequent WAN connectivity loss. The WAN works for a while, then stops working until the router is restarted, then fails shortly thereafter. I would assume it was some configuration corruption on incompatibility with the upgrade, but the symptom has been universal. EVERY 2.x upgrade I've made to a RV082 or RV042 router has exhibited this symptom. Reverting to the 1.3.98-tm firmware fixes the issue.
View 14 Replies View RelatedThis morning i upgraded a remote RV082 to 4.2.0.1 from 4.0.4.1. Numbers could be off slightly since i'm going from memory. I never got the normal acknowledgement the transfer was complete but after an ample amount of time closed the tunnel from my end, re- established my vpn but when i went to log in i received: RV082 firmware upgrade error? The requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist./quotei googled it and found similar occurrences with earlier upgrades. I'm assuming it didn't reboot itself upon completion of the xfer, at least i'm hoping a cold reboot will correct this but as i'm remote and this install doesn't have an ethernet power controller i'm stuck until monday. Should i bring a spare RV082 just in case.
View 3 Replies View RelatedI just bought the SRP541, and it has the old firmware. I downloaded the new firmware, yet I cannot figure out how to install it.
View 3 Replies View RelatedWe need to update the firmware for a small business router WRVS4400N. Unfortunately, I can't even burn the ISO file to CD after downloading it as instructed. I get the following error message: "The selected disk image file Isn't valid." I'm using a Windows 7 Ultimate computer.
I downloaded the proper firmware update for my version V2.0.1.3 router several times, but each time I get the same message.
The main reason we purchased this router for our business for for the extra layer of protection with ProtectLink. It has been over two years now, and we still have not got our ProtectLink service installed because we are unable to install the service until the firmware is updated.
After doing some research online, we found-out that the ISO file needs to be padded to 2 Kb in order to be valid for burning. The ISO firmware file you provide for this update is not according to my calculations. We have no way of converting the file myself and don't know what to do about this situation.
We are extremely taken-back at the fact that I must submit my issue here on a forum rather than address the issue directly to Cisco Support. We are very disappointed with Cisco support as they appear to want to charge additional money just to get an initial shipped-problem remedied. You would think that the company that essential built the internet infrastructure would be more considerate to their customers. We will never purchase another Cisco product given this level of terrible support.
we are going to see a firmware update for the RV220W before it becomes obsolete?
View 36 Replies View RelatedWe just purchased a new SRP 547W. When logged in with either the default admin or the cisco account there is nowhere to updare the firmware, but the manual says there is such a screen. The manual also mentions a "user list" under the "Administration" tab, but that is nowhere to be found either!
Model: SRP547W, ADSL2+ AnnexA, 802.11n FCC, 4FXS/1FXO Version ID: V02 Hardware Version: 3.1.0 Boot Version: 1.1.19 (Aug 24 2010 - 20:50:42) Firmware Version: 1.02.00 (023) Jan 6 2011 ADSL Firmware Version:0.60.0Recovery Firmware: 1.02.00 (023) Setup Wizard Version: 20101106.00
it wants me to download something for a bin file, is it safe?
View 1 Replies View RelatedI was going to update my firmware and the update for F5D8236-2 says it is version 2.01.03. At looking in my router it currently has version 2.01.06 (Jul 2 2009 22:24:38)Which should I be using?
View 1 Replies View RelatedLinksys WRVS4400N Current Firmware Version: V1.00.16
Tried updating the firmware to either of the two version you seem to have available, but fails with:
"Upgrade file is not the correct type or version for this device. Upgrade failed. Please obtain the correct file and try again."
Tried this one: WRVS4400Nv2_v2.0.2.1.img
And this one: WRVS4400Nv2-fw-2.0.1.3-K9.img
Then spent 2 hours trying to find how to get support for this product. where I may download the correct firmware for this product?
Is there any timeframe on an update for the RV220W firmware? I have had to take mine out of production due to it freezing up/locking up under medium loads. DNS queries (dig) don't respond, pings outside of the network don't respond. Pings to the router DO respond. SSH responds but I have no login info to proceed further. The config (web) page doesn't respond. Interesting enough nntp (news groups) DO respond and download fine. Eventually the unit catches up and the config page shows back up. I wish there was a way to login via the ssh to see what is going on internally with processes. I will have to find time eventually. Right now my old Linksys 54G with DD-WRT is smoking the Cisco router's performance.
View 2 Replies View Relatedi tryed to update my rv120w from 1.0.2.6 to 1.0.4.10 after about 15 minutes i power cycled the router.it now has alternating green power and wireless lignts flashing and router is unresponsive.
it does not give out ip address and not reachable when seeting static ip on cpui have tried the reset button.Can this unit be recoverd somehow?
I have tried to update firmware on a RV220W. Something stopped and now it won`t start. The power led blinks a few times and goes off, the LAN and WAN port wich is connected is lit. I have tried 10 seconds reset button but nothing happens.
View 1 Replies View RelatedI just bought an RV220w. My first act was updating th firmware to 1.0.2.4. Unfortunately I was not able to configure the router for vlan purpose 'cause the "Port VLAN" point was missing in the webinterface. I performed several factory reset but it didnt work for me - so I got back to firmware 1.0.1.0.
View 9 Replies View RelatedI've previously upgraded the firmware on our RV220W from 1.0.0.26 to 1.0.1.0 without any problems but all attempts to upgrade to the latest version 1.0.2.4 fails with the following message "Upgrade failed due to invalid/corrupted firmware". The router then automatically reboots with the current firmware.
We've already tried re-downloading and applying the update from several different machines using different operating systems and browsers without success. How to apply this firmware version successfully? We really need one of the VLAN fixes included in this latest version!
i got the RV042 and want to update the fw to 4.04.xx . After a few minutes, the browser wanted to perform the update again. I agreed and now, the webinterface isnt available and i cant get a IP from the router. So I tried to reset the router twice. After no success, I performed a factory-reset, which should work when I pressed the reset-button at least for 30 sec.Now the DIAG-LED blinks in a ~5sec rythm.What can I do?
View 2 Replies View RelatedI have done a firmware update at my repeater F5D8233-4. But now I have no access to the webGUI of the repeater. The SSID can be found and I can access the network. But I cannot connect a 2nd repeater now. How can I reset the old firmware?
View 1 Replies View RelatedThe unit was delivered with v1.00.23. The setup utility scanned and found update v1.00.99.
The belkin support site indicates that theer is a version 2.00.04, with no mention of v1.00.99. Which is the correct update to apply?
I cant find any info for my router F9K1004 on belkin's support site. I would like to see if there is a firmware update and if there is any info to setup my VPN at home.
View 1 Replies View RelatedDuring a firmware update, the router shutdown rebooted, stayed on for about 1 minute and then powered off and never rebooted. 750DB, F9K1103v1. What do I do next?
I was having intermittent internet issues. I was advised by my ISP to update the firmware. I tried via web browser but when I tried clicking on the firmware update link I would lose the page or the page wouldn't load.
I then tried running the cd and installed the bellkin software and got everything working - it asked me to update the firmware to which I readily agreed considering the request from my ISP. Then during the firmware update, my problem took place.
Retried multiple times to restart the router as well as resetting the router.
My SRP527W has never had its firmware upgraded since purchase. I had a need to do this recently, but could not find the section under Administration for Firmware upgrade.The only two items under Administration are Time Setup and Switch Setting.I've tried different browsers, to make sure that was not an issue, with no success. Any direct URL to the modem web interface that might allow me to update the firmware. url...Otherwise is there another method using a USB stick or tftp or similar?
View 1 Replies View RelatedMy RVS 4000 v1 router firmware version 1.3.0.5 has been intermittently going off-line ... a reset of the power resolves the issue temporarly. My plan was to update the firmware but I haven't been able to download an uncorrupted version of the firmware file on the Cisco support site. The file downloads as a zip file but the winzip program says that the file is not in a valid zip format and cannot open it.
View 1 Replies View RelatedWhen trying to update the firmware on my range extender, 192.168.2.1 does not work (per instruction page). When I found my default gateway address, it wanted me to login to my Netgear router -- not to the Belkin extender to which it's currently hard connected. F9K1106V1
View 2 Replies View RelatedMY belkin router model no :F5D7234-4v1, recognizes only my laptop and my other devices such as mobile and tab are getting the signal and w-fi gets connected but the internet is not working. when contacted service provider he asked to upgrade the firmware. Is there any recent version firmware upgrade of the model. current version is F5D7234-4_UK_1.00.01.
View 1 Replies View Relatedwhat is the recent version Firmware update for Belking router model number : F5D7234-4v2
View 1 Replies View RelatedI have recently acquired one of these routers. I thought, being a Cisco product, it would be the bee's knees. It is not. After finally getting the network set up - no mean feat, although I do not claim any expertise, but had to resort to some other network management software to finally get it all running - the router drops either the WAN connection or the wireless connection many times a day. The laptops often show as being connected to the network/router, but are unable to access either the internet, or the router via the browser. Re-booting the router is the fix, but, hey, I can achieve that sort of performance with any old $20 router - none of my old Net gear routers was this troublesome.
The permanent fix would seem to be a firmware upgrade, but guess what? The only options available under the "Administration" tab are time setting and switch settings - no firmware upgrade. The supplied firmware is 1.01.09(001) Apr 7 2010. Why these products are supplied, as new, without the latest firmware installed beats me, but there you go.
When i try to update the firmware it tells me the it is an incompatible update.ive followed all the instructions.my model number is f5d8235-4 v2.i have downloaded the correct version for the firmware update (2).
View 5 Replies View RelatedThere is no support for Model F9J1005v1. How do I update its firmware and how do I port forward on the same
View 2 Replies View RelatedHow do I update the firmware on my N wireless router with version 2000? It says there is an update, but I can't update it with the one firmware update that's available for download.
View 4 Replies View RelatedManual and firmware not available for my f7d2401nt. The US support page do not find the model, the italian support page find the model but link to the US page ! Someone has at least the manual (englis, french or italian language) ?
View 2 Replies View RelatedI have a Zoom adsl x6 model 5590 wireless router. I recently tried to update its firmware by following the instructions from the manufacturers site. Everything seemed to go correctly, but I am now unable to connect to the internet or my routers http address. My router now has a red power light along with a solid green light for the wlan and dsl.
View 2 Replies View Related