Cisco Routers :: RV220W - Upgrade To 1.0.4.17 Failed Due To Invalid / Corrupted Firmware
Mar 10, 2013
I have a RV220W running 1.0.1.0. When trying to upgrade to 1.0.4.17 I receive an error: "Upgrade failed due to invalid/corrupted firmware".
I found this article: [URL]
I assume I have to do a factory reset then an upgrade in order to upgrade properly.
If I do a backup running 1.0.1.0, then upgrade to 1.0.4.17, then do a restore, would that put me back to 1.0.1.0? I'm trying to avoid configuring the router manually all over again.
View 1 Replies
ADVERTISEMENT
Sep 25, 2011
I just bought an RV220w. My first act was updating th firmware to 1.0.2.4. Unfortunately I was not able to configure the router for vlan purpose 'cause the "Port VLAN" point was missing in the webinterface. I performed several factory reset but it didnt work for me - so I got back to firmware 1.0.1.0.
View 9 Replies
View Related
Sep 10, 2011
I am getting the following flooding the logs on my RV220W (IP Address replaced with X.X.X.X)
2011-09-12 00:58:54: [rv220w][IKE] ERROR: Invalid exchange type 243 from X.X.X.X[500].
2011-09-12 00:58:54: [rv220w][IKE] ERROR: Could not find configuration for
[Code].....
These are all coming from the same IP Address which is running Windows 7 Enterprise X64 using a WIRED connection.
View 3 Replies
View Related
Oct 15, 2012
When I access setup on an RV220W with Internet Explorer, Mozilla or Safari the following message always displays:
"There is a problem with this website's security certificate. The security certificate presented by this website was not issued by a trusted certificate authority. The security certificate presented by this website was issued for a different website's address."
I access the router by clicking on "Continue to this website (not recommended)."
This also happens anytime a URL filter is triggered by a client. I.e., clients do not see the "Blocked by Cisco Firewall" message unless they also click on the "Continue to this website (not recommended)." option.
Even worse, when I attempt to connect as a VPN, the SLLVPN applet gets java connection refused. This is why I bought this thing!
What do I need to do to fix all these certificate related errors?
View 3 Replies
View Related
Mar 15, 2011
DIR-655 RevA4 - upgraded to 1.35NA, which is shown on http://192.168.0.1/
When I try to re-log in as Admin, I get a message of invalid password. I have unplugged to reset, but still cannot get back in.
View 3 Replies
View Related
Jan 8, 2013
I get the message "Firmware upgrade has failed. Please ensure that valid entries were specified in the required fields." when I try upgrade the firmware rootfs.bin.
View 4 Replies
View Related
Dec 12, 2012
with TFTP upgrade SRW2xxG4_FW_1.2.3.0.ros and WEB interface after the restart, the switch will not start, display HyperTerminal link. You can also restore the switches do not?
View 1 Replies
View Related
Oct 20, 2007
When upgrading with .bin file (v1.05.8) via Administration - Firmware Upgrade, it fails when status showing 76% completion.
View 4 Replies
View Related
Feb 28, 2013
just troed to update FIRMWARE re our WRT54G_v2
current FIRMWAREFirmware Version: v3.37.7
downloaded and tried to run 130228dl_LINKSYS_FW_WRT54Gv4_4.21.5.000_20120220.bin
BUT got msg' Upgrade are failed!;
View 3 Replies
View Related
Feb 12, 2011
I've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.
View 2 Replies
View Related
Dec 25, 2011
first one had to get rid of because just wouldn't work with a 3CX server, anyway, I have a DIR-655 A4 factory shipped with 1.32NA I am trying to update the firmware to 1.34NA but it will not let me. It keeps saying Code:
View 6 Replies
View Related
Dec 5, 2011
I'm attempting to upgrade to firmware 5.00.38 for my WRT54G-TM router, but it keeps telling me "upgrade failed" after like 3-4 seconds of trying. It says I currently have firmware: DD-WRT v24-sp2 (06/13/09) mega - build 12288. I've tried restetting to factory defaults before upgrading
View 3 Replies
View Related
Aug 19, 2012
The label on my router says "WRT54GS" and the current firmware is 4.71.4.
View 1 Replies
View Related
Feb 10, 2013
Region : UnitedKingdom
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : 3-14-4 to 3-15-4
ISP : Primus Saver
I had it all working fine, then I wanted to upgrade the firmware. The original firmware was 3-14-4. I downloaded and applied the 3-15-4 firmware. Now when it powers on the power light is on all the time. Immediately the sys, 4, 3, 2, 1, Internet, usb and wps lights flash once. Then about 5 seconds later the 4, 3, 2, 1 & Internet lights flash once, then a second later the cycle starts again. When I connect it to the PC it starts to make a connection on the NIC, but then the router resets. Model: TL-WR1042ND, Ver 1.3 . Is there a way to reset the firmware or get it working again?
View 4 Replies
View Related
Feb 2, 2013
I tried to upgrade firmware (I entered my model number WRT54G and hardware version 2 into Cisco menu and downloded the upgrade file they provided. My version was v2.02.7, downloded file FW_WRT54Gv4_4.21.5.000_20120220.bin . After I run the upgrade it said upgrade failed. After that I can't connect to internet and can't access the router. I tried to reset it and unplug it- no luck. From my PC control panel I see local area connections status connected, but as I said, it does not connect to Internet.
View 7 Replies
View Related
Aug 24, 2011
I just bought a Cisco E4200 (from someone on Ebay, so returning is probably not an option). I was in the process of setting it up when it wanted to do a Router Update. Unfortunately, it did not specifically say to not do it WIRELESS. We had a disconnection in the upgrade process. Now the Power light just blinks. I can ping it from a hard-wired PC, but cannot get to the Administration Web page to retry the firmware update (I did download it from the site). Also Cisco Connect cannot connect to the router.
Oh Yes, I have tried holding reset button for 30 seconds, unplugging for 30 seconds, and replugging in the router. I do not get any different results.
View 6 Replies
View Related
Feb 22, 2012
My router: WRT160Nv3
My Firmware Version: v3.0.02
Upgrade version: Ver.3.0.03 Build 3
I can not upgrade, always gives the same error message: Firmware upgrade failed!
View 6 Replies
View Related
Dec 20, 2012
I have a Cisco RV220W updated to latest firmware 1.0.4.17. I have been trying to get a VPN setup for the past few days without success. We had a test VPN up and running previously, but when we changed the IP's and secret key to connect the live VPN tunnel it failed and we haven't been able to get it working since.We have deleted both ends, rebuilt them probably 6 times each. We have changed secret keys, tried 3DES, AES, and AES256 encryptions with SHA-1. All the internal IP settings are correct :IE 192.168.1.1/24 or 192.168.1.1 255.255.255.0,External IP's are right, only oddball thing here is one of the external IP's is assigned by DHCP and is a /22 although the previous tunnel worked with the same ISP.
View 1 Replies
View Related
Jul 22, 2011
i have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies
View Related
May 14, 2012
we are going to see a firmware update for the RV220W before it becomes obsolete?
View 36 Replies
View Related
Oct 20, 2011
Is there any timeframe on an update for the RV220W firmware? I have had to take mine out of production due to it freezing up/locking up under medium loads. DNS queries (dig) don't respond, pings outside of the network don't respond. Pings to the router DO respond. SSH responds but I have no login info to proceed further. The config (web) page doesn't respond. Interesting enough nntp (news groups) DO respond and download fine. Eventually the unit catches up and the config page shows back up. I wish there was a way to login via the ssh to see what is going on internally with processes. I will have to find time eventually. Right now my old Linksys 54G with DD-WRT is smoking the Cisco router's performance.
View 2 Replies
View Related
Dec 23, 2011
I noticed one awkward thing with the latest 1.0.3.5 firmware for the Cisco Small Business RV220W router, with previous firmwares there has always been reported 128mb of system memory (RAM) under the router dashboard. And several "teardowns" of this router has confirmed it to have 128mb of memory on the router board.
Does that mean the latest 1.0.3.5 has an odd visual bug, or has the RV220W gotten it's memory sliced in half with this firmware release?
View 4 Replies
View Related
Mar 13, 2012
I have tried to update firmware on a RV220W. Something stopped and now it won`t start. The power led blinks a few times and goes off, the LAN and WAN port wich is connected is lit. I have tried 10 seconds reset button but nothing happens.
View 1 Replies
View Related
Sep 4, 2011
I've previously upgraded the firmware on our RV220W from 1.0.0.26 to 1.0.1.0 without any problems but all attempts to upgrade to the latest version 1.0.2.4 fails with the following message "Upgrade failed due to invalid/corrupted firmware". The router then automatically reboots with the current firmware.
We've already tried re-downloading and applying the update from several different machines using different operating systems and browsers without success. How to apply this firmware version successfully? We really need one of the VLAN fixes included in this latest version!
View 3 Replies
View Related
Apr 17, 2012
Every time I try to download a torrent/magnet the router will crash/reboot multiple time (using utorrent 3).
View 5 Replies
View Related
Apr 24, 2012
I have read every post here about port forwarding on the RV220W and none are clear. Here is my scenario.
I have 5 static IP Addresses. I want to use one of the IP addresses to setup remote access using Remote Desktop Connection from outside the office using port address translation. for example i would like to use RDC and a specific port such as 7000 and connect to an internal PC on port 3389. sounds simple. i do this all the time on Cisco ASA's, Netgear, D-link, etc. but for the life of me cannot do it on this cisco firewall. so the port address should look like 25.25.25.25:7000 and connect to 192.168.1.25:3389. i have tried everything based on the posts without luck.
View 1 Replies
View Related
Apr 13, 2012
I have a Cisco rv220w. I just tried updating the firmware. I used RV220W-Firmware-1.0.3.5.img. It rebooted, and now there is no DHCP and no access to anything. I tried the reset button for 10 seconds. That didn't do anything. The WAN and all the LAN lights light up. Power is on and solid. The light blinks alternating between the DMZ and the blank space to the right of wireless. How can I get this back to factory defaults?
View 5 Replies
View Related
Mar 30, 2011
When my RV220W used firmware 1.0.0.26 the PPPoE login to AT&T/Bellsouth DSL worked just fine. I upgraded to version 1.0.1.0 and now it won't connect. The PPPoE connection still works from my prior Linksys router so there wasn't a change on the ISP side. Has something changed in firmware 1.0.1.0 that requires a change to the PPPoE profile?
DSL Modem is a Motorola Netopia (model 2210-02) with firmware 7.7.3r10 operating in Bridged mode.
View 26 Replies
View Related
Nov 5, 2012
I have a problem with my RV220W.
It reboots randomly every day and I got the following message in the log: [rv220w] System][FIREWALL] fwPPTPGenericRules.c: inet_aton failed I saw one internet that I can ask cisco for the Beta firmware 1.0.4.6 that fix the issues(Iactually use 1.0.4.17). Is it the solution? How can I obtain the beta firmware?
View 5 Replies
View Related
Nov 28, 2012
i tryed to update my rv120w from 1.0.2.6 to 1.0.4.10 after about 15 minutes i power cycled the router.it now has alternating green power and wireless lignts flashing and router is unresponsive.
it does not give out ip address and not reachable when seeting static ip on cpui have tried the reset button.Can this unit be recoverd somehow?
View 2 Replies
View Related
Sep 16, 2012
Or rather, it will connect within the first few minutes after a router reboot, but eventually is kept from connecting.
All settings look good. Upgraded from 1.0.3.5. Prior to upgrade, this was not problem.
View 3 Replies
View Related
Nov 11, 2012
From an older manual it describes how to configure this. I installed the oldest firmware available for download and this feature is there. Was this just simply moved somewhere else in the newer firmware?
Configuring Port VLANs
You can associate VLANS on the Cisco RV220W to the LAN ports on the device.
By default, all 4 ports belong to VLAN1. You can edit these ports to associate them
[Code].....
View 2 Replies
View Related
Jan 29, 2011
I corrupted my BEFSR41 firmware v4.2; is there a way to recover?
View 1 Replies
View Related
