Cisco Routers :: RVS4000 Slow With Fiber Connection?
Jan 8, 2012
I've recently upgraded from a 512k adsl connection to a 16mb fiber optic connection.Whereas I never had a problem previously, my rvs4000 slows to a crawl once or twice per week. The only solution seems to be to cycle the power since the admin interface freezes. I also have to cycle the power on my two wireless ap to get them back up.I believe I have the latest firmware, is this a common problem on a faster connection?
View 1 Replies
ADVERTISEMENT
Aug 18, 2011
My new RVS4000 (2.0.2.7) connects the WAN via PPoE with dynamic IP which is held at DynDNS and normally I see the RVS4000 via a router-to-router-VPN. That works fine so far, but every "some" days the router looses WAN connection (and with ist VPN). When this happens, last DynDNS-update is hours ago, so it didn`t reconnect. Looking on the routers site, the LAN is fully functional for clients that have got their DHCP-Information. New clients don`t get DHCP-Info (IP-address, DNS), both do not have internet access. The router`s WAN-summary shows, that it thinks to be "CONNECTED" but with empty WAN-IP and DNS entries. Klicking "DISCONNECT" and then "CONNECT" again solves the problem so far. The loss of connection is not the periodic break from the IPC, which is correctly identified and reconnected as configured. I wanted to trace the problem with the log, but there is also a bug. It stops logging at some time completely - neither email-log nor local log, so I never happend to be lucky to hit the point of loss of connection. Also the local log provides a first and next pages, but the next pages are always empty - not really useful.
View 3 Replies
View Related
Aug 25, 2011
We have two RVS4000 at both ends of a VPN tunnel. The tunnel is up and runs fine. I can ping the two servers at the main office end of the tunnel, and cconnect to the resources of both servers. However, one of the servers, the terminal server, is unreachable via RDP. The other server can be reached via RDP for administrative purposes just fine, but the terminal server cannot be reached. There is only one difference that I can think of. The terminal server is reachable from the outside world via a redirected forwarded port on the RVS4000 at the main office.
The current firmware version is V2.0.0.3 at both ends. Is this a known anomaly for this revision of firmware?
View 1 Replies
View Related
Apr 8, 2012
Just recently purchased an RVS4000 to take the place of an old NetGear FVS336, which supported multiple NAT translations. It appears that the RVS4000 does not support this, any other models in the small business line support this? I only need this for a backup Internet connection?
View 4 Replies
View Related
Aug 7, 2011
Recently i bought a Cisco RVS4000, upgraded the firmware to latest stable release (Firmware Version: V2.0.2.7) and started configuring it.Yesterday i found out that as the dsl connection drops (i'm using PPPoE with an ethernet ADSL Modem) the product stops logging, both locally and to an external configured syslog (which resides on a linux box over the LAN).
View 3 Replies
View Related
Feb 22, 2012
The firewall on my RVS4000 appears to hang when ever I use Netflix. If I disable the firewall and re-enable it it works for a while and then stops again. My IP address is in the Approved Client IP Addresses so it is excluded from the URL filtering and Web reputation rules.
View 5 Replies
View Related
Aug 5, 2011
I'm an IT professional with more than 10 years experience. I have spent last 5 days trying to figure out why the wifi connection to this router is so slow, but still no luck. I'm getting only 13Mbps even if my laptop is next to the router! (wired connection worked ok)
I have tried all sort of setting combinations, 2.4GHz/5GHz; N only/ G,N Mixed; Auto/20MHz bandwidth; different channels; WPA2 encrypted vs open; disable firewall; wmm enabled/disabled; 1.0.0.26/1.0.1.0 firmware... no matter what I try, I always get only 10 - 15Mbps speed.
Once I replace this router with my old router, it worked perfectly --- getting 70 - 80Mbps with exactly the same testing environment and configuration.
I really expect this router to offer much faster wireless speed according to this review: [URL]
View 12 Replies
View Related
Dec 20, 2012
i got an issue with vpn and cisco rv100w, router is configured well and computers and iphone can connect with PPTP. Problem became when we map NAS drive from computer or we move data (1-4 Mb). Seems connection go down, speed is so slowly and drop the connection.Is it from router? or from Internet provider?
More data, If I connect to http of router/NAS .. all go fine, only when we need data from NAS (map drive by windows) copy, open files, ..., connection is so slowly and drop connection.
I saw in the logs of the router
[code]...
View 1 Replies
View Related
Nov 17, 2012
My ISP tested my connection and told me my signal is very weak. I can no longer play games online because I lag tremendously. I can't steam videos while someone else is using the internet either. Also I can't access it on wireless devices unless I am in view of the router. I'm not sure what caused my connection to suck butI have the essential plan from cox.com. When I test my connection on speedtest.com I average 75ms/ping, 3.25mbps/dwnld spd, and
View 2 Replies
View Related
Feb 10, 2013
Belkin N300 - bought two weeks ago and have had very slow internet connection since.
View 1 Replies
View Related
Nov 21, 2012
My Router has been gone from running at bout 7Mb download speed to 500Kb download speed. When the router is restarted using the menu software it will run quicker, but only for 20-30 second then back to a slow speed. It was off while we were on holiday in August and has not been any good since. Its a shame as it only 2 years old.
View 2 Replies
View Related
Feb 13, 2013
Having an issue with my Belkin N600 router - when initially installed it was working fine but in the past week it has gtten slower - if I connect directly to my DSL modem my speed is 1.5 MBS when I use the router connection my speed drops to .1 MBS - tried resetting to factory defaults & that did not work also tried resetting my modem *& router still having the same issue.
View 9 Replies
View Related
Nov 20, 2012
My N150 wireless router sees 25mb+ speed from my internet connection but my wireless connects at 1mb. Why is the WiFi being resricted?
View 2 Replies
View Related
Sep 11, 2011
I have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies
View Related
Sep 22, 2012
I have been doing network and computer work for a small public library which will soon be needing to change internet providers. Our planned route will be to have a fiber connection directly from our local ISP, but we need to figure out the best network hardware to accommodate this network connection.We currently have two HP 1810-24G switches connected to a Sonicwall TZ100 firewall as the primary router. The firewall/router connects to the internet with Cat6 connected to a fiber optic media converter. The media converter is on lease from the current internet provider so it will be gone.Our new ISP has said that they can provide a fiber connection in our building to an SFP port termination, which is their recommendation. Ideally, this would be an SFP port in a router or firewall. However, there seems to be very few options for routers with SFP and they're all incredibly expensive compared to a network switch with SFP. While I imagine we could just terminate the fiber optic connection into a cheaper switch with SFP and connect to that with the firewall, our network is further complicated in that we have a CISCO LifeSize video conferencing system which ideally runs best without running directly through the firewall, which can cause some lag and glitches in the signal it seems. I don't believe it's possible to have the router WAN interface connect through to the ISP with a static IP and PPPoE sign on as well as another network devices using the PPPoE and a separate static IP address, am I correct?Have I just over-complicated this network issue, and everything should just be run behind the existing firewall, or should I be able to find a different firewall/router or switch that can connect with SFP to the ISP?
View 2 Replies
View Related
Jul 20, 2011
My Storage supports RJ45 Connectivity. Some it gives slow performance. What if i connect all the Macpro using fibre optic and use some sort of converter to convert all the fibre connection to LAN. Will it increase performance?
View 2 Replies
View Related
Jun 24, 2012
I have a Cisco ASA 5520 that I'd like to be able to connect directly to our gigabit fiber connection (we're currently connected through a media converter that's causing problems). I've found the following:Cisco ASA 5500 Series 4 Port Gigabit Ethernet Security Services Module [URL]. I only need a single fiber connection, as opposed to the 4 copper + 4 fiber.
View 1 Replies
View Related
May 30, 2012
We’ve just begun the transition from our old 3Com switches to new Cisco switches and we’ve encountered interoperability problems as we start the transition.Goal: Extend 6 VLANs (each representing an IP subnet) via fiber from a port on the 3Com 5500G-EI to a port on the Cisco SG-300-52
We assign an IPV4 address to the Cisco SG-300-52. We can successfully ping/web-manage at this address if we do a temporary copper jumper from a 3Com switch to the Cisco. IP address is in the subnet assigned to VLAN7•2) At the 3Com side, the fiber port is set as “hybrid” and is passing VLAN 1 untagged; VLANs 3-8 tagged•3) At the Cisco side, the fiber port is set as “trunk” and is defined with VLAN 1 untagged and VLANs 3-8 tagged.
If I try to change the management interface on the CISCO from VLAN 1 to VLAN 7 (as I would on the 3Com), I lose connectivity over the temporary copper connection•B)
If I remove the temporary copper jumper from the Cisco (keeping the “working” management IP address) and create the fiber link between the 2 switches, I lose connectivity to the management IP , If I set the 3Com fiber port to “access” and make the fiber connection, I can ping the management interface – but of course, I can’t pass the other VLANs to untagged access ports on the Cisco – and it has the fun side benefit of messing with IP management settings on other 3Com switch stacks attached to the 5500G-EI. However, it does demonstrate that we can get network traffic communicating over the fiber link between the 2 switches.
How I can proceed to a) have the management IP address in the IP subnet defined on VLAN 7 while passing the other VLANs to access ports on the Cisco? BTW, I’m a networking neophyte (it’s a very small part of my job and I do it infrequently), so I prefer to use GUI management to CLI options, although I can perform CLI configuration if presented with the right commands.
View 1 Replies
View Related
Jun 4, 2013
We are migrating from a Microwave T1 WAN to a Fiber ring WAN which I'll be connecting to our providers Ciena Metro E switches. Eventually we are going to move away from the routers, but the network is a little too complex as well as spanned across a lot of miles. Since I am the only networking personnel here, I would like to first simply migrate to the fiber by simply moving the connection configs off of the T1 interfaces, and onto one of the Gig interfaces on the 7206 and on one of the Fe interfaces on the 3900 (which is actually a 3700 series because the line card on the 3900 is toast). If this works, I will need to purchase Fe line cards for the 7206, because I found out that the virtual interfaces do not support Policy Mapping for our QOS and Multicasting.
View 6 Replies
View Related
Feb 9, 2013
We recently moved to a new office and currently have three ISPs(DSL, SAT, 4G) because we are unable to get Cable nor Fiber services. We have anywhere between 7-20 Remote Desktop connections(with lot of file transfers) and 8 VOIP lines. Basically, we need to bind certain services to specific WAN links in order to make everything work somewhat decent because of the limited bandwidth and/or latency of each ISP.
I would like to double check if the bindings are working for the specific services, and it has been difficult to verify if the settings in the RV016 are working. I believe it's not working 100%, and I need a way to check and make sure that my settings are being followed.
What would be the best way to check the current connections to see if the service is being routed via the WAN link specified in my setting? My RV016 is HW ver 3, but not the latest firmware. Purchased about 2 months ago.
View 4 Replies
View Related
Apr 20, 2013
Ive set up a rvs4000 with two vlans, one as a bussiness network and the other as a guest network. Everything works fine and the networks can not see each other. I would like to add wifi and I would like to do so with keeping both networks separate. I have a used 1130AG access point and was wondering if I could use this single AP for both networks. If so, how would I go about doing so? Is there a better suited AP for my needs?
View 4 Replies
View Related
May 16, 2012
I have an RVS4000 running V2.0.2.7 firmware that gives me an "Invalid Character(s) Found" error message when I try to edit an existing ACL.
I'm trying to deploy 57 of these routers and would like to be able to use a pre-built config dropped onto each router.
I initially planned on editing the exported config with a find&replace for my local LAN addresses. Since that didn't work the next reasonable solution would be to edit the ACL list (much more tedious, but still better than hand-entering every ACL on all 57 devices).
when this bug will be addressed? Alternatively, if there is an offline configuration editing tool I would be one happy camper to have it!
View 2 Replies
View Related
Jun 3, 2013
I have an RVS4000, not installed. How can I tell from the unit or the packaging that it is a v1 or a v2, without installing and switching it on (which I don't want to do now) ? Are v1 branded Linsys and v2 Cisco ? Can you tell from the date on the package (mine says copyright 2011) ?
View 1 Replies
View Related
Sep 4, 2011
I don't know if my vendor mislead me, but I need to do this: There is a public subnet in my office, not a 192.168.x.x, but a real Public IP.The reason is that we do VOIP and those are only servers. I installed a RVS 4000 in that location, and assigned a PUBLIC Ip to BOTH the WAN and LAN, since when I connect from outside, using either QickVPN or another identical router, I need to be assigned one of the PUBLIC Ip's on the remote LAN. That is the whole idea of the project, to locate servers remotely and make them use our set of PUBLIC IP's. Well, so far I cannot connect either with the Quick VPN client, or using the VPN Wizard. It goes and creates the tunnel, without error, but when I click test, it fails.
View 2 Replies
View Related
Mar 15, 2012
We have backup and other traffic over our vpn which is affecting our ip phone service between two sites. Our consultant suggested implementing QOS over the VPN to give the phone traffic priority. Is this possible with the rvs4000. Is there any good source saying how to do it. Is the setup of the QOS on this router similar to another router where this has been discussed.
View 1 Replies
View Related
Mar 19, 2012
I have problem with bandwidth management on my RVS4000.
That is the way how i done it:
All traffic (TCP & UDP on all ports)
IP range 192.168.0.2 - 192.168.0.2 (My IP adress)
Guaranted download speed 1kbps
Maximum download speed 5000kbps
after saving setting and rebooting router I have maximum download speed on my PC 12000kbps, Why QOS doesnt work ?
View 3 Replies
View Related
Nov 11, 2012
I am getting ready to setup an RVS4000 so we can use the VPN functionality of it, but I am not quite sure of the correct way to integrate it into our network though. I do not need site to site, just the client portion of it for a few salesmen/off site people to use. I have never used or setup a VPN before, so I'm learning everything as I go along.
We are in the middle of switching our ISP and I am waiting to set this up until the new service is live so I can test it prior to moving the rest of the company to the new ISP.
We are switching to Comcast, and will have 5 static IP's available to use. Currently, the firewall does all our NAT and is the forward facing device on our network. I would like to leave the firewall in place (although I am setting up a new firewall for the new internet connection) and have th RVS 4000 sit behind it and receive VPN traffic from a WAN to LAN rule We currently have a 192.168.100.0/24 network.
Do I need to setup another /24 network for the VPN to function behind (and still have access to the 100.X network), or is there a way to allow everyone who connects to receive a 100.X ip address from our DHCP server. I'm not sure how to set everything up with the WAN/LAN connections on the RVS4000 to acheive this.
We are running a domain on a 2008R2 server. The clients will be using laptops that are already part of the domain, if that will make a difference.
View 2 Replies
View Related
Jun 15, 2011
I'm trying to setup a VPN tunnel between a Cisco RVS4000 on our side and a Cisco ASA5520, to connect a machine on our local network to a test server on the target side.
We have all the settings setup correctly and the tunnel is up and running, however, our local machine can't connect/ping to their server. I've tried a trace route both from the machine and from the RVS4000 itself, and they both get stuck after getting past 192.168.1.1. Is there any routing or NAT-ing that I need to do on our router? Or is there a problem somewhere else?
View 7 Replies
View Related
Aug 8, 2009
I'm having an issue with a Linksys RVS4000 which doesn't appear to be behaving as I think it should.I need to forward a port (Single Port Forwarding) through to an internal NAT host. However, I only want that host/port to be accessible from one host on the internet, for security reasons.
I have created the port forwarding entry and this works fine. I then created two rules in IP Based ACL - one to block all access to that port from the WAN interface and one to allow access from a single host.
However, it appears that when a port forwarding entry is added, it will completely bypass the ACL and allow all traffic for that port/host by default.Is this the correct behaviour?
Firmware version is v1.2.11
View 12 Replies
View Related
Sep 13, 2011
I'm currently dealing with a weird problem on a Cisco RVS4000. I'm trying to connect to a IPSEC VPN Gateway (NETASQ) located on the LAN side of the RVS4000. I'm using Green bow vpn client on the WAN side of the RVS4000. Basically I'm trying to get through the RVS.My VPN config is OK because i tested it on the LAN side of the RVS.
The RVS is configured like this: NO VPN configured.
Block WAN Request :OFF
FIREWALL,IPS,DDOS are OFF
NAT forwarding on for UDP 500 and 4500 directed from the wan to the ip of the VPN gateway. Seems right because iv managed to do this with other routers (different brands) on another site.I've wire sharked my vpn client and i keep getting ICMP destination unreachable (PORT UNREACHABLE) after my ISAKMP launching packet.Can the RVS nat these ports ?
View 3 Replies
View Related
Jan 11, 2012
I've been trying to disect this problem for a few months to no avail. The router allows me to connect to outside FTP only when IPS is enabled. The moment I disable the IPS functoin, the connection hangs and does not connect to a server. Reason I'd like to keep IPS disabled it is because it's eating up half of bandwith when enabled.RVS4000
View 2 Replies
View Related
Jul 23, 2012
When it comes to fiber optics my knowledge is very limited. All I know is that they can carry data at high bandwidth for a long range at blazing speeds etc.My boss has asked me to link several buildings to the network and I am led to believe that joining them through fiber optics to be best since we are expecting a lot of data traffic between.I have done the normal RJ-45 networking with Gigabit networking in my organisation but need your assistance on how to join each of the buildings through fibre optics.So far this is my plan.Draw up the fiber optic lines from the main building to each building.All the buildings have Gigabit Cat6e cabling and network in each.I am planning on using a single mode media converter to convert the end of the fibre optic to the normal RJ45 connector and plug it to each switch at each of the ends of the fiber optic cable .Am I going in the correct direction?I don't even know the gadgematics required except for the cables them selves, crimping tools, the media converter. There is about 300-400 metres in between of each building from the main building.Also, I believe that we need to create cross over cables as in the normal way we do in connecting 2 switches. Your input is very valuable to me.
View 9 Replies
View Related
Dec 9, 2012
Just bought N150 router. Have fiber optic to PC now. Want to add wirelss to use laptop in other parts of house. Plug cable company CAT5 into port marked "Modem" and then my pc into one of the LAN ports ?
View 1 Replies
View Related
