Cisco Routers :: To Configure An RV082 For Dual Wan And VOIP

Mar 5, 2012

We have a RV082 configured with two ISP Wan connections. We recently implemented a VOIP phone system (SIP) (192.168.1.50) that is being used in appliance mode on our network. We currently have two WAN connections Load Balanced. My goal is to configure all my VOIP traffic to go out through the 1st ISP and the rest of the data through ISP #2. is this possible to achieve using the RV082? We are using a Skype SIP Trunk connection.

ADVERTISEMENT

Cisco Routers :: RV082 - Settings To Improve VOIP

Feb 7, 2012

We have recently purchased an RV082 router for our company. I have successfully managed to establish a VPN connection through PPTP and through Quick VPN (IPSEC?)
 
When i am connected through PPTP my software SIP client has 0.5% packet loss which is totally acceptable. When i am connected through Quick VPN my software SIP client has a 50-70% packet loss.
 
i have done the following settings on the router: Bandwidth Management:

High Priority for upstream and downstream UDP 10001-20000 and UDP 5060-5080
 
Wan Connection settings: MTU: 1492 bytes
 
I would like to know if there are any other settings that will improve VOIP over Quick VPN since RV082 supports 100 connections compared to 5 for PPTP.

View 2 Replies View Related

Cisco Routers :: Dual WAN And Log Mail SMTP On RV082?

Jul 23, 2012

I use a RV082 with dual Wan and I cannot configure two SMTP.
 
Without authentication; a SMTP is specific of the provider.
 
When WAN1 comes down, SMTP to be used is the SMTP corresponding to WAN2 and vice versa.
 
Implementation of authentication with the mail server wil be useful. Possibility of two mail servers with indication of the corresponding WAN is also useful.

View 1 Replies View Related

Cisco Routers :: RV082 Dual WAN Configuration Required

Jun 12, 2012

RV082 configured for Dual WAN [Code]....

(2) identical DSL connections, configured as Static IP (not PPPoE) with modems in bridged mode. Static IP's are /25 subnet and same gateway  ** this may be a problem? Dual WAN set for Load Balance, network service detection is OFF
 
We have a 2003 terminal server running and successfully receiving connections through both WAN connections.  Depending on location, half the users are connecting to WAN1 IP and the other half to WAN2 IP.  We are getting sporadic disconnects of the remote users when they are idle for a couple minutes and automatic reconnection of the session takes over a minute.  If they close the (locked up) session and reconnect manually it will let them in right away. 
 
Could the handling of the Dual-WAN be the culprit?   Could the same gateway for both WAN's create this issue upstream (out of my control)?I am going to move everyone to connecting through WAN1 and then change to Smart Link Backup and see if the issues persist.
 
Another thought is to use a secondary IP on the terminal server and use Protocol Binding to match "All traffic" for IP1 to WAN1 and IP2 to WAN2, which theoretically would stabilize the situation?

View 36 Replies View Related

Cisco Routers :: How To Configure QoS For VoIP In RV220W

Jan 8, 2012

I have a cisco RV220W router used in a home environment. Recently I purchased a Siemens Gigaset A 580 IP phone. It works OK so far but I would like to optimize the configuration for VoIP traffic and apply QoS for VoIP on this router. Any guide with the recommended configuration and preferred settings of the same? I have not used QoS previously

View 1 Replies View Related

Cisco Routers :: Rv082 Configure One-to-one Nat

Nov 17, 2011

isco epc3925 in transparent bridge provided by isp with following wan details

ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
 
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.

View 4 Replies View Related

Cisco Routers :: RV082 - Configure WAN2 In DMZ Mode On Each Router

Jan 15, 2013

We have 2 offices in different countries both using the RV082 router.  Currently both offices have an internet connection on WAN1 and that is working fine. We are adding a Point to Point circuit between the two offices, and my question is on the RV082 configuration on each side.
 
I was going to configure WAN2 in DMZ mode on each router, then connect the point to point circuit to the WAN2 port.  On the China side, the DMZ IP will have to be a private address (192.168.177.1), while the DMZ port on the San Diego side will be a public IP. We need internal computers to be able to go to the internet normally through WAN1, but also go through WAN2 if they are trying to reach the other network.  I will be adding routes on each RV082 for this.
 
Is there anything wrong with this configuration?  Do I need to change the routers from Gateway to Router mode?  Does it matter if the DMZ WAN2 port has a private IP address?

View 2 Replies View Related

Cisco Routers :: Configure RV082 Router With Mac Native VPN Client For Remote Access

Oct 9, 2012

I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?

View 2 Replies View Related

Cisco Routers :: Configure RV042 Dual WLan / Web And DNS Server

Aug 19, 2011

I need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN

View 1 Replies View Related

Cisco Routers :: RV042 Dual WAN VPN Router - How To Configure Dynamic DNS

Apr 22, 2013

Cisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?

View 1 Replies View Related

Cisco WAN :: RV082 Dual Wan Terminal Server Configuration

Jan 31, 2012

I've a RV082 with 2 internet connections.The idea is to permit external connections to my server and if one Internet line falls, automatically switch to the other.
 
We have configured the router in Smart Link backup.We try to connect with WAN1 and WAN2 enabled and all works fine.
 
We try to connect with WAN1 disabled and automatically WAN2 is activated.The problem start here...if WAN1 is activated while there are connections using WAN2, these connections falls!
 
How I must configure the router to permit that active connections are not disconnected from WAN2 even when WAN1 connection come back?

View 1 Replies View Related

Linksys Wired Router :: RV082 - Set Up Dual WAN?

May 15, 2009

I am trying to set up a dual WAN on my RV082 - I have Verizon DSL on WAN1 and I am trying to establish Time Warner Road Runner on WAN2 as a backup in case DSL goes out on WAN1.I cannot get the router to recognize both connections at the same time.  I have power cycled everything, the router is only picking up one internet signal at a time.

View 3 Replies View Related

Cisco WAN :: RV082 V4.1 Internet Hang Until Cold Restart On Dual WAN?

Dec 22, 2011

I am having issue with a RV082 with firmware:

v4.1.0.02-tm (Sep 16 2011 18:40:48)
 
On setup 1 I have;Using 2 WAN, 1 from fiber 5mbps symetric fixed public IP and other is DSL private dynamic dhcp address 3mbps/900kbps

 On setup 2 i have:Using 1 WAN, from fiber 5mbps symetric fixed public ip Both router have exact same firewall configuration, subnet and port forwarding and we have the seccont backup DSL coming in a few day for setup 2.on both setup, the RV082 is the main internet gateway/firewall for a set of server...
 
Setup 1 work perfectly and been online for 2 week (since install) without issue
 
Setup 2 worked for 2 day then had to reboot, then work for few days then need reboot, now it look like it need to be rebooted every day. the internet just stop working and a simple reboot does the trick... also, when that happen I can stil remote in server that have port forwarded in the router or connect to router management port, but internet on the server is down... I tried opendns and google dns on both WAN connection and still no luck.I have followed instruction on various support forum;

-more reliable dns server
-lower MTU
-failover vs load balance
-disabling SPI and DoS protection
 
at this point I'm about to swap both router to see if it not a defective hardware or disconnect DSL WAN on setup 1 to see if its more stable but the whole point of installing this router was for Internet redundancy which so far dosent work as expected.

View 2 Replies View Related

Cisco Firewall :: ASA 5505 Configure QoS And VOIP With SIP Trunking?

Sep 16, 2012

[URL] I am not savy configuring ASAs at all and I can't get it to work. We are switching to a SIP trunk phone system and I am in charge of setting up the ASA to not only make it work but also make sure that there's packet priority or QoS.I've never configured something like this and I was giving another set of instructions to make sure that this is working:

[URL]

Configuration:
My configuration is very basic:
3 interfaces - Outside/Inside/Guest
ASA Version: 7.2(3)
ASDM Version 5.2(3)
Firewall Mode: Routed
 
Solution: When I tried following the instructions on brian-kayser's blog I get an error when I'm sending the following command:

shape average
^  Invalid marker
service-policy PRIORITY-POLICY
^ Incomplete command 
 
I think it's because my version of ASA doesn't have this functionality but I don't know.

View 5 Replies View Related

Cisco Switching/Routing :: SG300 Configure QoS For VOIP?

Mar 13, 2012

I'm looking to configure the QOS for VOIP on my network.I have a switch SG300 and several no Cisco VOIP phone. What are the parameters to be taken to implement the QOS?
 
What is the procedure for installing the QOS? I need to create a VLAN for the data and one for VOIP?I read in the quick start guide  that there is auto-QOS for VOIP?This can be done from the GUI? what are the options to put?

View 0 Replies View Related

Cisco Routers :: VPN Configuration For Dual WAN On Dual RV042

Feb 21, 2013

I run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
 
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
 
I got problem though when i tried more complex connection diagram. [URL]
 
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.

View 2 Replies View Related

TP-Link Dual-Band Wireless :: VOIP Dropped Calls Over TP-Link WDR4300

Feb 14, 2013

Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast

I just upgraded my DLink DIR655 to WDR4300. My VOIP service has worked for the last 5 years. But with WDR4300, I'm frequently experiencing dropped calls. The call will be cut off every 20 seconds or so. This is really a deal-killer.

View 7 Replies View Related

Cisco WAN :: 3945 To 7206 Router Via IGX 8400 / Configure VoIP With Existing Frame Relay Network

May 19, 2011

Application is that need to configure the VOIP  with the existing Frame relay network ,where VOFR  command is not shown in the router when type yhe command router config#dial-peer voice 123 need vofr On the 3945 router where in the router it is not accepting the above command,

View 8 Replies View Related

Cisco Routers :: VPN Between Two RV082 Routers Not Working?

Aug 7, 2012

We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
 
One of the router is a V2 and the other is a V4 if that makes any difference.

View 12 Replies View Related

Cisco :: Configure And Utilize The Dual WAN / ISP

Aug 30, 2012

I would like to configure & utilize the dual WAN / ISP to which we have subscribed. At present we are serving web-pages through our primary ISP which is working fine.

View 3 Replies View Related

Cisco Routers :: VOIP Configuration - SRP547

Feb 6, 2012

I am unable to get any configuration parameters to work on my SRP547 for VOIP. ADSL2 works fine. Equipment replaces a ya.com (Arcadyan ARV4518PW) which worked ine albeit with significantly less features. Problems encountered due to the lack of equivalents for some parameters and an overabundance in the new unit which simply don't exist in the Arcadyan product.

View 7 Replies View Related

Cisco Routers :: Connect SPA122 For VOIP?

Jan 2, 2013

Here is my setup:
 
Cisco SPA122
Apple Airport Extreme Wireless Router
imac 2.8GHz Core 2 Duo
Thomson DCM475 Cable Modem
 
The imac is on a desk in the kitchen and is out main computer. The Cable modem, SPA122 and Airport Extreme are in the den just beside the kitchen.
 
I guess my first question is if the SPA122 has to ABSOLUTELY be attched to the computer? Right now I have it attached:
 
Cable to cable modem
Cable modem to Airport Extremet
Airport Extreme to SPA122
 
In this configuration, I can not access 192.168.15.1

View 2 Replies View Related

Cisco Firewall :: Configure Dual ISP On 5505 8.4

Mar 27, 2013

I am attempting to set up failover dual ISP on a 5505 running 8.4(4) with the Sec Plus  license. Everything i have been able to reference so far, points to old commands not available or relevant in 8.4
 
For instance:
 
global (backup) 1 interface
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 20.20.20.1 1
route backup 0.0.0.0 0.0.0.0 30.30.30.1 10
 
What is the new syntax that should be used to mimic these commands?  I have the sla and trach reachability configuration already set up.

View 1 Replies View Related

Cisco Routers :: Voip With SRP547W And SPA303 Phones?

Oct 28, 2012

I have an SRP547W hooked up as the office router with the standard office phones connected via the telephone ports at the back of the unit using 2 SIP lines as well as the PSTN by dialling hash first. We have just added a new staff member and bought an SPA303 with the intention of connecting it through registered SIP lines on the SRP547W, and hopefully have the facility to use the PSTN line when the SIP lines are busy.
 
The problem is, it connects to VLAN100 and gets its IP address and initializes fine however no lines show as configured and it can't make or receive calls. What do I need to configure on the SPA303 to tell it to use the SRP547W as its SIP Server/Proxy (not sure of the terminology).

View 4 Replies View Related

Cisco Routers :: RV042 Protocol Binding For SIP And RTP (VoIP)

Jun 26, 2012

I have a RV042 with a DSL (WAN1) and cable (WAN2) internet connection in Load Balance Mode. The DSL provider also provides internet telephony when registered via his line. When I disable the WAN2 port, my IP phone successully registers with the registration server of the DSL provider. I also defined protocol bindings for SIP (port 5060) and RTP (ports 5004 to 5020) to be bound to WAN1. My IP phone is set up to listen on only these ports. [code] With these protocol bindings in place when I re-enable WAN2, then after some time the phone reports "registration failed".Do I need to set something else apart from protocol binding to force the VoIP traffic to go via WAN1?

View 23 Replies View Related

Cisco Firewall :: PIX515 6.3.3 - Configure Dual ISP On Two Interfaces?

Jul 4, 2011

I have a pix515 v6.3.3. Is it possible to configure dual ISP on two interfaces and have redundancy between them?

View 1 Replies View Related

Cisco VPN :: ASA 5520 - Configure VPN To Dual Remote Endpoints

Dec 13, 2011

Not sure if my subject is a good decription of the problem or not.
 
I have an ASA 5520 at my home office and a SonicWALL NSA2400 at my remote office.  The remote office has dual internet connections and I wanted to create two seperate VPNs between the devices using each internet connection on the SonicWALL.
 
I know how to configure this on the SonicWALL, the problem is on the ASA 5520
 
OK Basic network config
 
Main Office

ASA Public IP 1.1.1.1

ASA Internal network 192.168.1.0 (VPN source)
 
Remote office

Public IP 1     2.2.2.2

Public IP 2     3.3.3.3

Iternal network 192.168.2.0 (VPN destination on ASA)
 
If I have a VPN from the main ASA to either one of the SonicWALL's public IPs everything works fine

If I create 2 VPN tounels from the main ASA, 1 to each public IP on the SonicWALL, the VPN shows as up but no traffic flows.

View 1 Replies View Related

Cisco Routers :: Prioritize RTP Packets For VOIP Audio On RV180

Sep 26, 2012

Advanced networking but have managed to get our small office IP PBX running over a SIP Trunk. The only real problem we are having is choppy outgoing audio when there is other heavy outgoing traffic on the network.
 
My understanding is that I need to set some QoS parameters, which I have played with but it didn't seem to be useful. I mostly dealt with allocating bandwidth. I now think I need to somehow prioritize the outgoing RTP packets from our PBX (which runs on a PC on our LAN) to avoid the choppy audio. My research shows this can maybe be done with something called DSCP 46 and my router does support that -- how to exactly set the configuration.
 
Our router is a Cisco rv180w.

View 4 Replies View Related

Cisco Routers :: WRVS4400N Stopped Working With VOIP Phone

Mar 1, 2013

I have the router for over two years, Present Firmware is V2.0.1.3, I have Polycom phone connected to the router using 8 x 8 VOIP service. The phone was working fine untill yesterday. 8 x 8 tech support suggested getting a different router. I have the same router at home and tried the same phone on my home router - it worked. So, the problem is not the phone but int he router. I tried to call Cisco tech support but found out that the warranty support expired and I need to buy a support plan. Called to buy the support, and gave up after an hours on hold. Left  message.

View 1 Replies View Related

Cisco Routers :: LAN To LAN Routing RV082?

Jan 29, 2013

We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
 
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
 
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port. 

View 4 Replies View Related

Cisco Routers :: RV082 VPN Passthrough

May 9, 2013

I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
 
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
 
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.

View 1 Replies View Related

Cisco Routers :: RV082 / No Connection To ISP

Nov 12, 2012

I have reset my RV082 router (both wit the reset  switch and the factory default wizard) and run the setup wizard but  regardless I can't connect to shaw.ca which is my service provider. I  notice that if I use http://192.168.1.1 the browsers (IE & FF)  default to https://192.168.1.1 and then I am prompted for a certificate.  I can enter if I ignore the request but after getting in I simply  cannot connect to my ISP.

View 4 Replies View Related

Cisco Routers :: RV082 NAT To Other Subnets?

Jan 12, 2012

Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.

View 4 Replies View Related

Cisco Routers :: VPN Fail With RV082

Jan 14, 2013

I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
 
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
 
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
  
Tunnel Interface is setup on WAN1, checkbox is enabled.
 
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet

[Code]....

It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
  
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
  
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723

View 4 Replies View Related

Cisco Routers :: RV082 Restarts Itself

Jul 28, 2010

we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
 
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.

View 20 Replies View Related

Routers / Switches :: Manage Static IPS In VOIP Setup?

Jul 21, 2011

I have VOIP and was provided a modem, a Tilgen Router (Vood 452_A). I also currently have a Linksys WRT54G router. I also have a home surveillance system with a DVR that can be accessed via the net. I am trying to allow the ports to open so that traffic can navigate down to the DVR.My IPs:My VOIP has provided me with 6 static IP addresses. For sake of this issue they are:

67.xx.xxx.153, through .158My subnetmask is set to:

255.255.255.248My Settings:

The Modem is connected to world. To the modem I have the Tilgen Router connected. The Tilgen is set with an ip of .153 and the subnetmask listed above. DHCP is turned on and has IP range set for .154-.158. It is set in Bridge Mode with NAT and Firewall turned off. To that I have the WRTG54G router connected and assigned the router an Static IP of .154.. The cable is going into the Linksys WAN port.From a computer connected to a LAN port on the WRT54G, I see my public IP as .154, currently my internal IP is 192.168.1.15 so I believe I have to assign one of my Static IPs to this PC, however when I try to connect to the Linksys Router (.154) from the outside web, I am get a time out error. (also from a ping test.) My thoughts are to assign the Linksys to DHCP and use a range of .155-.158 to give each lan item a static IP. My question is will this work? Will each item in the network have its own IP and if I forward the port to the DVR that i needed, ie 80 for web client or 6100 for desktop client, will that forward through?Or do I set it to Router Mode and use the Tilgen to assign the ips.

On the Tilgen I also have an option for a DHCP relay or to turn off DHCP.

For clarification here is the setup chain
Broadband/DSL Line>>Tilgen Modem>>(LANPort1)Tilgen Router(LAN Port2)>>(WAN) Linksys(LANPort1)>>DVR/Computers
Found this walkthrough on setting the WRT54G into a Switch. If I did this, in theory the VOOD would assign those computers/dvr connected downstream via the WRT54G a static ip from my range set on the router. Then in theory I would not need to port forward port 80 since the DVR would be on its own public IP.?

View 7 Replies View Related

Cisco Switching/Routing :: How To Configure Dual ISP On Router 2821

Mar 17, 2013

I've 3 interfaces on router:

Gb0/0-ISP01 with DHCP client
Gb0/1-ISP02 Static IP 192.168.2.x/24 
Fa0/0 - LAN 192.168.1.1/24
 
I want to know, how to configure:1. Set the IP of interface Gb0/0 as dhcp client from ISP01 and make it as default route.
 
2. How to configure the ip nat.....overload?
 
3. How to use the ip sla to monitor internet connectivity to 8.8.8.8 for ISP01, if it fails, to go to ISP02.

View 3 Replies View Related

Cisco Routers :: RV082 NAT Table Too Small

Mar 15, 2013

I have an RV082  10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.

View 3 Replies View Related

Cisco Routers :: Are RV042 And RV082 SIP Aware?

Jul 18, 2012

Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.

View 2 Replies View Related

Cisco Routers :: RV082 Web Admin Lockup?

Oct 20, 2011

Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section.  I have tried using both IE and Firefox and have used multiple workstations.  I get to the login screen but it doesn't get any further.  I am running the latest firmware v4.0.4.2-tm.  It works for a while then just stops.  The only fix is to turn off the device and back on and then it starts working again.
 
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.

View 7 Replies View Related

Cisco Routers :: Outbound Nating With RV082?

Jan 9, 2012

I just migrated our office network router to a RV082. While configuring it, I came across three problems: 
 
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
 
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
 
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
 
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway

View 0 Replies View Related

Cisco Routers :: Rv082 Dmz Rule Limitations

Apr 27, 2013

we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.

View 0 Replies View Related

Cisco Routers :: RV082 LAN Subnet Mask

Nov 12, 2012

I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.

View 8 Replies View Related

ADVERTISEMENT