Cisco Routers :: Voip With SRP547W And SPA303 Phones?

Oct 28, 2012

I have an SRP547W hooked up as the office router with the standard office phones connected via the telephone ports at the back of the unit using 2 SIP lines as well as the PSTN by dialling hash first. We have just added a new staff member and bought an SPA303 with the intention of connecting it through registered SIP lines on the SRP547W, and hopefully have the facility to use the PSTN line when the SIP lines are busy.
 
The problem is, it connects to VLAN100 and gets its IP address and initializes fine however no lines show as configured and it can't make or receive calls. What do I need to configure on the SPA303 to tell it to use the SRP547W as its SIP Server/Proxy (not sure of the terminology).

View 4 Replies


ADVERTISEMENT

2620 - 79xx Series VOIP Phones

Jun 10, 2012

I have some 79xx series VOIP phones that are acting VERY strange ... if you are familiar with these series phones once plug them into the PoE switch they look for a TFTP server with the call manager files to acquire all the info they need to work .... i have them set up on a 2620xm router running IOS c2600-ipvoicek9-mz.124-15.T14 along with call manger 4.3. My router is my TFTP server and i have hooked up and fixed over 50 of the same series phones with out a problem.

Now here is my issue ... when you goto press the SETTINGS button on the phone you are allowed to go into the settings of the phone to change all the ROUTER,TFTP,ETC info to allow you to connect your phone to the CALL MANAGER or you can set up DHCP and it will acquire the info automatically. When i press the SETTINGS button nothing happens .... i can reset the phone to factory defaults by holding the # button then 12345678*0# then 2 not saving the info and i can hit the restart buttons which is * 6 SETTINGS buttons together and that will let me restart the phone but i cannot manually set up this phone to do anything .. it will not acquire info form my DHCP server and will not find my TFTP server at all =( the phone SETTINGS BUTTON does not respond at all ..only when restarting the phone.

View 19 Replies View Related

Cisco :: VoIP Phones Customization - Ring / Backgrounds

Mar 12, 2012

has anyone here played around with uploading compatible audio files for custom rings and MOH and/or personalized backgrounds for the phones? I was only taught the basics in our CUCM v6.0.1 and am looking to figure out how to get some good music on my phone as well as play around with other "cosmetic" features. The phone I'm testing with is a 7971(color).

View 4 Replies View Related

Time Outs On LAN - VoIP Phones Have A Delay Internally?

Oct 6, 2011

A couple of users on my network complain about timeouts. They access the same server which runs a SQL server. People from outside world can access it without a problem but internally it keeps timing out. I have also noticed that VoIP phones have a delay internally. So if i pickup my phone and dial an extension the other person can't hear me sometimes but i can hear him.

I have experienced the VoIP problem but have never had any time outs on my machine. I tried packet capture on a couple of computers but i cant see anything out of the ordinary. Alot of ARP, some STP which i think shouldn't reach the machines, dropbox traffic etc.

View 2 Replies View Related

Linksys Cable / DSL :: WAG160N Doesn't Work With VOIP Phones

May 21, 2011

I purchased Linksys WAG160N (from a store)  and I also have 7 Linksys SPA962 VOIP phones provided by MyNetPhone with service included. All tests we found out that this modem doesn't work with this VOIP phones. Somehow probably doesn't give access to MyNetPhone servers to get connection with this phones.I purchased an other one from DLINK and works perfect?

View 1 Replies View Related

Cisco Switching/Routing :: Will ACL110 Allow IP Phones Communicate With VoIP Server

Nov 13, 2011

Will ACL110 allow IP phones communicate with VoIP server. Do I need to add line to allow multicast traffic? [code]

View 0 Replies View Related

Cisco Switching/Routing :: WS-6509 / VoIP Phones Random Outage?

Jan 2, 2012

All of our VoIP phones bounced (re-registered) in the middle of the work day and we do not know why. There is no maintenance going on at this time. The phones came back up right away. Upon further investigation, I only found one error message on our core switch (WS-6509 running IOS ver. 12.2(18)SXF13) and I'm wondering if that was the cause:
 
Jan  3 13:51:04.030: %SIBYTE-SP-5-SB_OUT_OF_RX_DSCR_CH1: Out of RX descriptors on mac 0 - channel 1 (count: 299)
 
I cannot find any other instances of this error message from the internet.

View 1 Replies View Related

Cisco Switches :: SG200-50 VLAN For VoIP Phones Connected To SRP541W Router

Apr 15, 2013

I am new to VLANs although I generally understand the concept.  I have a small office with 25 desktop/laptops and 15 VoIP phones connected with a SG200-50 switch and on Port 1 I have the Cisco SRP541W router for DHCP and Internet access.  My goal is simple: 1) Segregate the VoIP phones (voice) from the computers (data) and 2) Prioritize the VoIP phones traffic.
 
I believe this can be accomplished by setting up a second VLAN and maybe a third (if the default should not be used) and then identifying those ports as Voice VLAN ports.  I guess I just need to know how to flag each interface and each port so that they all can talk to the router on Port 1 yet the voice and data will be in different broadcast domains.  Also, do I need a management VLAN??
 
Is this setup correct? VLAN 1 - default (data) Port 1 (Trunk) (Tagged)Port 2 - 30 (Access) (Untagged)VLAN 2 - voice Port 1 (Trunk) (Tagged)Port 31 - 48 (Access) (Untagged) What should the interface settings be on each port (General, Access or Trunk)? What should the port VLAN membership be on each port (Tagged or Untagged)??

View 4 Replies View Related

Cisco Routers :: SRP547W Wi-Fi Drop Out

Apr 2, 2012

i see that the wifi on the SRP Freezes. If i am connected via lan, i can still surf the net or connect to another access point on the network and surf. But the wiress devides connected to the SRP loose connectivity even though it shows that the wifi connection is connected. I am running on the latest firmware. this problem has started occcuring only recently

View 3 Replies View Related

Cisco Routers :: SRP547W - Multiple WAN IPs?

Mar 18, 2012

There are a few discussions on this topic but nothing I can find indicated definativley shows that this can be done with this model.I have an ADSL service that came with 1 IP address and then we later purchased an additional 4 IPs (2 usable) for the same service.On our network we have SBS2011 and also a dedicated web server. What I would like to do is forward HTTPS to the web server on our inital IP and then forward https for OWA  to one of the IPs on the additional set.Our initial IP is xxx.yyy.104.112 which I would like to forward port 443 to  192.168.0.12 - web server
 
The additional IPs are :
 
aaa.bbb.30.24 (Gateway Address)
aaa.bbb.30.25
aaa.bbb.30.26 - I would like to forward this to 192.168.0.2 - SBS box
aaa.bbb.30.27
 
I have tried as suggested in other thread setting up a software DMZ that sends public IP aaa.bbb.30.26 to 192.168.0.12. The xxx.yyy.104.112 to 192.168.0.12 works with a port 443  forward fine.
 
When I do this I cant connect from outside. If I change the port forward on 443 to go to 192.168.0.2 I can get to the SBS box from outside using the aaa.bbb.30.26 address .I have also tried creating a subinterface for the aaa.bbb.30.24 addresses and this also doesnot seem to work. Just I am basically asking for confirmation that this can be done with this model, I have put in the latest firmware.

View 3 Replies View Related

Cisco Routers :: How To Administer SRP547W Over IPSec VPN

Sep 5, 2012

I've got a network of SRP547Ws connected with site to site IPSec VPNs. But I can't get to the administrator loging page of the remote SRP547s over the VPN. Is there a setting or method I need to use ?
 
I have looked at the remote administration settings but this appears to be for adminsitration over the WAN interface rather the the IPSec VPN

View 2 Replies View Related

Cisco Routers :: To Use Compatible 3G / 4G USB Modem Via SRP547W

May 29, 2012

Currently, I have setup a demo lab with the UC320W + IP Phones and OnPlus Network Agent all connected to a SG300-28P. I have just obtained an SRP547W because I wanted to use the 3G/4G internet connection via the router as my demo lab is an isolated network.Now, I tried to a couple of 3G modem (UMG181) and 4G Telstra modem (MF821) on the SRP547W but none of these work. I had a look at the compatibility tableI guess those modem models are not listed there. However, when I went on say the Optus website to scout for a more compatible model, none of them hit it right on the mark. The matrix says it can support E180 (while Optus has the E188), E353 (while Optus has the E353). I have already wasted my money on getting the earlier stated 3G/4G Modems and I ain't going to take a chance again.

View 1 Replies View Related

Cisco Routers :: USB Modems Support For SRP547W

Aug 9, 2011

What is the current list of supported USB modems for the SRP547W router?

View 1 Replies View Related

Cisco Routers :: How To Configure SRP547W To Support ANNEX M

Jan 18, 2012

How to config SRP547W to support ANNEX M

View 4 Replies View Related

Cisco Routers :: SRP547W Multi Static Public Ip?

Sep 25, 2011

my Networks contain three devices (BPX, DVR, PC) need to fixed IP, do you router supports the Cisco SRP547W  Static Public ip.

View 1 Replies View Related

Cisco Routers :: How To Disable DHCP Server On SRP547W

May 24, 2012

I've purchased a router SRP547W and I would disable DHCP server. On the control panel I can't see anything about disabling this function. I don't need dhcp server on router and I don't need dhcp relay. My firmware version is 1.2.4_003.

View 4 Replies View Related

Cisco Routers :: SRP547W - How To Use Multiple WAN IPs For Port Forwarding

Sep 10, 2011

We've run into some difficulty trying to take advantage of multiple WAN IPs in conjunction with the SRP547
 
What we're trying to acheive is the ability to port forward from our distinct public IPs to different internal servers. Looking at the options under Port Forwarding it looks like we can only configure forwards at the "WAN interface" level, but our problem is that we can't work out how to set up separate interfaces for each of our Public IPs...
 
Our ISP provides us with a fully managed NTU/router with a single "Internet" ethernet port, which we can use by statically configuring IPs on our end. For this configuration this port has been directly patched to the WAN ethernet port on the SRP547W.
 
We have been allocated a 255.255.255.248 (/29) subnet, giving us 5 usable IPs after the ISP's gateway address is taken into account, like so:
a.b.c.208     Network Address (/29 subnet)
a.b.c.209     ISP Gateway
a.b.c.210     IP1

[Code].....
 
I should mention at this point that we're running on firmware version 1.02.01 (023).
 
Is there a CLI or other method of configuration that might work if the web interface won't?

View 2 Replies View Related

Cisco Routers :: SRP547W Dropping ADSL Every Minute

Feb 22, 2012

We installed one of these devices as our gateway a couple of weeks ago, flashed the firmware to 1.2.4(003) and it worked perfectly until this morning where it keeps resetting the ADSL every minute and losing the web interface to the unit.
 
The log endlessly reports this:
Feb 24 11:26:00 SRP547W cron.info cron[8779]: (root) CMD (/sbin/check_gn)
Feb 24 11:26:00 SRP547W cron.info cron[8781]: (root) CMD (/sbin/check_ps)

[Code].....

View 17 Replies View Related

Cisco Routers :: SRP547W - Selecting NAT IP From Static Range

Feb 18, 2012

I have a SRP547W which I'm trying to replicate a configuration I had on an old Cisco 847 that recently died.
 
My ISP has allocated me a /29. The DSL configuration means that the IP address on the PPP session is assigned randomly. I have a mix of internal devices on a private IP range and a few devices with publically accessible addresses. All of the devices on the internal network need to be NATted to a public IP from the range allocated to me.
 
I can see that I can use the software or hardware DMZ to set up the servers, but I can't see any way to configure the external NAT address.

View 1 Replies View Related

Cisco Routers :: SRP547W - LAN Configuration For Connecting To BT Infinity Line?

May 8, 2013

We've just purchased an SRP547W that we'd like to connect to our BT Infinity line. What the WAN configuration should be?

View 5 Replies View Related

Cisco Routers :: SRP547W Cannot Create Advanced Firewall Rules

Feb 27, 2012

I have a SRP547W that I have configured the following way:
 
LAN 192.168.15.1/24 VLAN1
LAN 10.10.10.1/24 VLAN10
LAN 10.10.2.1/24 VLAN100
PPPOE ADSL
Software DMZ going to 10.10.10.x and another to 10.10.2.x - this is working OK
 
I now want to use the Advanced Firewall features to block all ports except those that I need as the software DMZ forwards everything. When I try to create the rules I get "the values are invalid" message no matter what I try.
 
I want to create explicit allow rules, followed by a deny all rule for each of the IP addresses used for the software DMZ
 
Have I got the Subnet Mask Correct for the Destination IP? Or should it be 255.255.255.0? It doesnt make a difference either way
 
Policy DetailsNameValueSource IP Address0.0.0.0Source Subnet Mask0.0.0.0Destination IP Address10.10.10.xDestination Subnet Mask255.255.255.254ProtocolAnySource PortAnyDestination Port443ActionPermitScheduleEverydayTimes24 Hours 

View 6 Replies View Related

Cisco Routers :: Multiple Fixed IP Addresses On PPPoE With SRP547W

Mar 27, 2011

 I have an ADSL connection and have configured the PPPoE subinterface on WAN1 (ADSL)  this connection has a static IP, and I know that the ISP gives that to me through DHCP however I have 4 or 5 additional IP addresses also provided to me on that same link, and they are not given to me via DHCP. 
 
How do I configure this router to have multiple fixed IP addresses on a PPPoE interface?
 
I also need to port forward some ports for each of the IP's but I assume this will be easy after i have the IP addresses setup.

View 4 Replies View Related

Cisco Routers :: Router On A Stick VLAN With SRP547w And SG200

Aug 14, 2012

As per the title, I just require 3 to 4 VLANS with inter-VLAN communication enabled. 
 
In the past I have used this router with each port of the internal switch set to a different VLAN, with each in turn hooked up to an unmanaged switch.  This has work fine for me but I want to dip my toe in the world of .1q VLANS and gain some added flexibility and neatness.

View 3 Replies View Related

Cisco Routers :: SRP547W - Can't Ping External Side Of ADSL Interface

Mar 2, 2013

I have installed a couple of SRP547W's and can't ping the external side of the ADSL interface.
 
Is there an option to turn on "respond to ping" and also are you able to forward to a internal IP?

View 3 Replies View Related

Cisco Routers :: Srp547w Restarts When Edit Security In Wireless Table?

Feb 13, 2013

I have recently purchases a Cisco srp547w for my organisation. It is working fine with one SSID enabled. I have configured everything with no problems using the Web interface. However, whenever I click the Edit button, in the Security column, in the Wireless Table under Basic Wireless Settings I get a pop up message which says :"Some values have been changed. The router must restart the wireless module to take effect.Please wait several seconds" I have tried this using 3 different browsers and get the same behaviour in each browser.

View 1 Replies View Related

Cisco Routers :: SRP547w - Change Default IP And Create Additional Users

May 12, 2013

Ive changed the IP address of a laptop to connect to the router with IP 192.168.15.1 but now want to change the router IP address from the defaul to another subnet, so that it is accessable with other workstations on the LAN, but I could not readily find the option to set the Ip address on the router. 
 
I'm signed in with user admin.
 
I also wanted to add addiontal users.  The help indicates there is a User List Add Entry option but from the Administration bar, the left hand menu option shows User Management & User Privileges options.  On User Management, it is possible to change the 2 default user names, but I wanted to leve them and create new ones.

View 2 Replies View Related

Cisco Routers :: SRP547W Multiple IPSec Policies Through Single IKE Policy

Apr 7, 2012

I am trying to create a VPN between an SRP547W and a Cisco IOS router, in this case a UC540.I am running firmware 1.2.4 (003) Jan 11 2012. Now I can do this with an SRP527W and many other routers successfully. Including other IOS routers 1801, 1941 etc.
 
The issue I have is on the SRP547W I cannot create more than one IPSec Policy through a single IKE policy. I require this to route multiple v lans to our remote site. When I try to add an additional IPSec Policy I am give the error "IKE policy has been used by other IPSec policy"
 
This is possible to do on the SRP527W with latest firmware. I have tried rolling back to earlier firmware but instead I am given an error about overlap. Latest release note for this firmware suggest this issue was already resolved.

View 7 Replies View Related

Cisco Routers :: SRP547W IP Phone Access To Line Number Via Wi-Fi Voice Vlan?

Mar 19, 2013

The SRP547W supports creating both Wifi Voice and Data vlans.Can I configure a Wifi IP Phone to connect to the SRP547W Voice Wifi Vlan and have the SRP associate it with Line 1 (in lieu of a standard phone connected to the Line 1 FXO port - without additional hardware)?

View 1 Replies View Related

Cisco Switches :: SG200-26 VLAN To SPA303 Not Working?

Apr 16, 2013

We recently purchsed a SG200-26 and have several SPA303 with the 2 ports. The other component is a Sonicwall NSA3500.The SG200-26 is on an interface of the Sonicwall that interface has a primary of 172.20.3.x and the sub interface is 172.20.5.x. I labed the VLAN as 5?I went to the "Create VLAN" in the SG200-26 and also created VLAN 5 and under Voice VLAN the ID is 5.Then I went to the SmartPort and assigned GE24 as IP Phone + Desktop. That was OK. But when I go to the SPA303 and Enable VLAN and VLAN ID 5 I get Initializing Network. I am able to ping the 172.20.5.1 which is the gateway for the VLAN but still pull no IP. I also have an DHCP range assinged the subinterface.I also am using Cisco Configuration Assistant. I can see the switch SG200-26 and my IP set but it shows no IP. So I know that the CDP from the phone to the switch is working.

View 2 Replies View Related

Cisco VPN :: 8961 - IP Phones With AnyConnect On ASA / Can't Call Other Remote Phones

Jan 4, 2012

I have a CUCM BE environment with a number of remote users with 8961 phones connecting to an ASA 5501 via AnyConnect.  The phones register fine and can make inbound/outbound calls as well as four digit dialing to other users at the corporate site.
 
The problem is when a remote user tries to four digit dial another remote phone.  The called phone will ring but there is dead air once answered and then the line goes dead.
 
This sounds like a routing issue to me. How to get AnyConnect clients to be able to reach each other?

View 3 Replies View Related

Cisco Routers :: SRP547W Site-to-site VPN With L2TP Over ADSL

Oct 25, 2011

I'm installing a new SRP547W for a client and am having trouble setting up a site-to-site vpn. They are using the WAN1 ADSL interface for their internet connection. When I add a sub interface to it I am unable to see the 'Connection Type' drop down like I can see on a WAN2 ethernet sub interface. I have followed the instructions on page 29 provided here: how I can get a a site to site vpn set up on this router using either PPTP or L2TP over the ADSL interface.

View 1 Replies View Related

Belkin Routers :: N150 - Uploading Photos From Android Phones Wirelessly?

Mar 12, 2013

I got f9k1001v3 (n150) router, My problem is that I can't upload photos from my xperia p wirelessly. I tried to other connections (wifi) even on 3G and I can upload on instagram or fb.

View 3 Replies View Related

Cisco Routers :: How To Configure QoS For VoIP In RV220W

Jan 8, 2012

I have a cisco RV220W router used in a home environment. Recently I purchased a Siemens Gigaset A 580 IP phone. It works OK so far but I would like to optimize the configuration for VoIP traffic and apply QoS for VoIP on this router. Any guide with the recommended configuration and preferred settings of the same? I have not used QoS previously

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved