Cisco Routers :: WRV210 - Can't Ping Other Devices On DLink Bridge
Sep 4, 2011
I have a DLink wireless bridge connected to the wireless WRV210 router. All devices connected to DLink can access internet/email fine and can ping the WRV210, however, they can not ping any device connected to the WRV210 router, nor can any device on the WRV210 ping devices on the DLink writeless bridge. All devices are on the same subnet, 192,168.100.X with mask 255.255.255.0. All devices get their address from the WRV210.
View 7 Replies
ADVERTISEMENT
Oct 3, 2011
I have a new d-link wireless N 150 home router DIR-600. I heard of the wan ping which works it connect for online gaming, does or does it not turn on when you install it and is there any other things i can do to improve it? can't connect to League of legends
View 4 Replies
View Related
Mar 31, 2012
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies
View Related
Apr 25, 2012
I have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655
Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
View 6 Replies
View Related
Nov 28, 2011
I have WRV210-E V01 router and there is only 11 (instead of 13) WiFi channels available. Firmware 2.0.1.5. How to get all 13 channels (European ETSI standard)?
View 1 Replies
View Related
Feb 12, 2012
I have a Westell 7500 wireless modem that I would like to bridge to my Dlink DIR-628.
View 1 Replies
View Related
Feb 21, 2011
I have a big problem with my cisco wrv210. I want to use URL Filtering to block facebook.
Enable
ip range : 192.168.2.5-192.168.2.254
url string : Facebook, www.facebook.com , facebook.com notting work.
View 1 Replies
View Related
Aug 24, 2011
I am trying to connect a new Cisco WRV210 Router to the Internet via a D-Link (Yes I Know - you have to work with what you've got) DSL-320B ADSL2+ Ethernet Modem and can't seem to get a connection.
View 5 Replies
View Related
Aug 14, 2011
I have a WRV210 Router which I am trying to use VPN remotely to work on my home files while away. I have been able to connect to the router but cannot see any lan network. I have three desktop CPU's 1 W7 and two XP pro operating systems. The one DT I tried stopping fire wall - no lan. I set up an exception in the firewall. I have tried to get you the info thru clips and file capture of the status of the router.
View 1 Replies
View Related
Jun 13, 2011
I've began having problems with the WRV210 where the router just reboots. Sometimes it may go for an hour or more then it slips into a series of reboots. The up time varies so I see no pattern. Contacted support they thought the device may have been defective so we did a RMA. Well guess what? The replacement arrived on Friday we put it in place and the same thing is happening. We are not using any of the VPN or VL options. Just simple PAT to a few internal machines for RDP access and an internal exchange server. The Qos is all disabled. It has the newest firmware which I have reflashed. I'm at a loss to explain the behavior but it doesn't appear to be isolated to a defective device.
View 13 Replies
View Related
Dec 12, 2012
I am attempting to setup a network containing two routers, a primary giving me ADSL internet access (a 3com 3CRWDR101A-75) and a secondary router that has VPN (Cisco WRV210).
The primary router has the following LAN settings: 192.168.0.1 / 255.255.255.0 with DHCP enabled. WRV210 has the following LAN settings: 192.168.1.1 / 255.255.255.0 with DHCP enabled. Cable connection is from LAN port of first router to Internet port on second router. In this way, I'm able to get internet browsing on 2 laptops connected to WRV210 I have also a Panasonic IP PBX connected on the second LAN (the WRV210)
I need to setup the VPN on WRV210 to be able to get SIP calls from outside of the local networks (through internet). As I am a novice in networking, both routers are on DEFAULT setting.
I have learned a lot during the last 7 days to be able to understand the networking concepts but failed to setup the correct configuration.
For example if I change WRV210 from gateway mode to Router mode, I will not able to browse the internet despite the Help file that says "Select the mode in which this Router will function. If this Router is hosting your networks connection to the Internet, select Gateway. If another Router exists on your network, select Router. When Router is chosen, Dynamic Routing will be enabled"
Also i am able to ping the first LAN 192.168.0.x from WRV210 but not on the other side (from primary router to WRV210).
I am confused to use and combine different settings (NAT, Routing, Ports, ...)
View 6 Replies
View Related
Sep 12, 2011
I got a client who's getting a VOIP system installed into their/my network. The VOIP IT guys are demanding a separate static public IP address to be forward/made available to their router. They will put their phones on a different local subnet.
So here's what I've offered them and they refused:
1. separate PPPOE login; that way we share the modem and each router handles their own session (cleanest solution but they don't want to pay extra)
2. plug their router into DMZ of my WRV210 (they said they require publicly routed IP going direct to their device (but in this case they would have to assign my private IP as their WAN IP and all internet traffic would go to them unfiltered))
View 9 Replies
View Related
Jan 7, 2012
My wireless devices are having a hard time connecting though my router. They see the router and can connect to it but cannot get on the internet. When I go into my router and check Wireless Status to see connected devices the window is empty. Usually if I reboot my router some of my devices will connect but if I leave them idle for any amount of time the connection is dropped. Suggestions. I have Dell 530 desktop running Vist Home Premium and the router is Dlink Dir 615. The desktop has no issues connecting to the internet as it is connected through LAN port
View 2 Replies
View Related
Sep 27, 2011
I have a WRV210 router that is not allowing me to delete a VPN client that I had perviously set up. When I go to remove this client on the VPNVPN Client ACCESS table the s/w re-directs me to the Status VPN client table. There I cannot flag/check the disconnect box. I have version 2.0.1.5 s/w which is the latest.
View 0 Replies
View Related
Sep 23, 2010
I purchased a WRV210. I configure the device, setup all my tunnels, WAN, LAN, Wirelss, Security, etc. and within 48 hours it "automatically" resets itself back to "out of the box" settings. This has happened twice now - once after it ran for about 4 days and the second time after only 5 or so hours of opperation.
Is this a known issue with the device? Is there an update I need to apply? I'd give ya my current FW version but I cannot login as it appears to have rest once again lol - and my tunnels are down so no remote access.
I made a backup of the config after the first unscheduled reset - (.bin file) so I have my settings ready to restore.
View 6 Replies
View Related
Oct 30, 2011
I have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
View 1 Replies
View Related
Aug 10, 2011
I was configuring a new unit straight out of the box to test a configuration for a client. I got most of of the configuration done and was noticing the menus were quirky and so I check to firmware and discovered it was 1.1.16 (* down level).
I finished my setup and rebooted to complete the changes, when I went back to log into the console it would Actively refuses to connect . the first time after powering on it shows the page title as setup before failing
I have tried a hard reset ( 15 Seconds reset) but it does not work . it doesn't even reset the settings. (static IP etc still there)
how can I get it fixed / exchanged under warranty
View 1 Replies
View Related
Nov 6, 2011
I recently switched operating systems from XP to Windows 7. Since that time whenever I need to reboot the router, it does not recognize my printer. How do I set the router to a static ip address and will that affect its recognition of my computer? I have had no problems with computer recognition, only printer.
View 3 Replies
View Related
Feb 18, 2013
- Small Home-Office network based on a Cisco WRV210 VPN Router connected to another WRV210 in a remote location.
- The WRV210 provides 2 WAP-protected SSIDs, one for the office network and one for visitors
- Wireless channel is set 5 channels away of the closest networks (using inSSIDer)
- There are about 12 wireless devices, 4 connected to the office network the rest to visitors. Not all devices are connected at the time of failure. All wireless devices use DHCP which is set to last 1 day and provide 100 IPs.
- The wireless devices are 1 desktop, 3 notebooks (all clean), iPads, iTouch and Nook.
- The failure symptom is that almost daily, and most likely around the same time, no wireless device can connect to any of the SSIDs unless the router is power-cycled. During the failures, which we have witnessed first hand, there are no apparent reasons: no new SSIDs, now SSID in close range on the same channels, nothing we can easily observed in the network in terms of connections or unusual activity.
- A weirdo also presented by the WRV210 was that its web pages were shown erratically. That was corrected by downgrading the firmware from the latest to previous version.
We have used a loaner Linksys router WRT54GC with only the visitor Network on it and even though the situation is not as frequent, it has happened already a couple of times.The WRV210 is out of warranty and discontinued, so we get no support from Cisco that is worth paying for.
View 1 Replies
View Related
Sep 26, 2011
I recently purchased a WRV210 router. I'm trying to set it up and right now I have my server acting as my DHCP server. I can not change this. How can I have the WRV210 recoginize this and pick up on this so that computers connected wirelessly to it will receive IP Addresses from my DHCP Server and not from the router? Right now if I turn all DHCP off, I'm unable to connect to the router.
View 3 Replies
View Related
Aug 26, 2012
I have a VPN working between two locations using WRV210s at each end. Now I'm looking to replace one 210 with a new RV110W. Can I get the two to work together? The config is quite different.
View 4 Replies
View Related
Dec 21, 2010
I'm using two WRV210 Linksys Cisco Routers to create a tunnel between two places with a pppoe adsl internet connection.I made several tests with new 2.xxx and old 1.7xx firmware, and nothing changes.Try to reset to factory defaults, and nothing changes.I have two problems:
1) The router crashes after a time working, usualy around 24 hours, sometimes more, sometimes less. The lights still flashing, but nothing happens, no VPN traffic and no ping response from the router, and of course, no internet access. I could see just that the router works a bit hot, but, I think that is normal.
2) The VPN IPSEC was configured, and both configurations are identical. All value are the same, I am using the dyndns service. So, the VPN quickly connects and I can ping and access remote computers. Windows Folders, VNC, IT'S REALLY WORKS FULL. WORKS REALLY FINE. PERFECT.
BUT, when the router crashes, as I've told on problem 01, after remove the power cord and insert ir again, the VPN don't reconnect.On log's, I could see that it's say that has no preshared key. [code] But, it worked before. Nothing changes, nothing, the router just restarts. No configuration was lost, (I checked the VPN IPSEC TAB), but says that have no preshared key,The unique way to restablish the connection is go on the VPN IPSEC TAB, and change symetrical any configuration, as change MAIN MODE to AGGRESSIVE on both routers.So, now are as MAIN. Tomorow probably it will crash, so, I will have to restart both routers, and change to AGGRESSIVE. So, when it happens again, i will have to back to MAIN.
View 19 Replies
View Related
Sep 20, 2011
In the Internet Setup area (WAN) when I change to Static IP I can't change the Subnet Mask from 255.255.255.0 to 255.255.255.240 which is the information currently in my D-Link router. When I try to save the changes I get the error "The IP address is not in the right subnet". I find it hard to believe that a lowly D-Link $35 router has nore capability then a Ciso Small Business Router.
View 1 Replies
View Related
Nov 22, 2011
I have configured a router WRV210 and I left it enabled in order to access it remotely, but I can not connect to it. I have checked the settings and everything is fine, but if I try to access it from anywhere in the website does not load, either IE or Firefox or Chrome.
View 7 Replies
View Related
Oct 13, 2011
I have a DGL-4500 D-Link router as a base. And a DAP 1522 Ethernet Bridge I use to connect 3 devices and another router I am looking to host a media Server for the house(on the bridge).
View 5 Replies
View Related
May 27, 2012
Dlink Dir-657 keeps losing internet connection on wifi devices only . the connection remains to the router but no internet .if I disconnect the connection i am unable to reconnect to the router until i reboot it. My internet remains on my network cabled devices .I am running on an empty channel 3 , usually happens 20 to 60 minutes after the router is up . Dlink sent me a replacement refurbished one and this one is doing the same thing . I owned the original one for about 5 months with no problems at all ,no new electronics in the house and have not changed the placement of the router .
View 4 Replies
View Related
Feb 17, 2012
I recently updated my firmware in my WRV210 router to Version 2.0.1.5 which is the most recent on Cisco's download page. After upgrading the firmware, I found that some of the administration pages do not appear to load correctly in internet explorer version 9.0.5. For example, the ADMINISTRATION -> MANAGEMENT page has data but to see the data, I have to scroll down about 3 pages. All five entries under STATUS do not have any data visible at all which is typical for most of the other administration pages. An image of the Status Router page is inserted below. I have logged in to the administration pages with an old version of Firefox 3.0.14 and the pages are visible. The operating system that I am running is Windows 7 64bit.
I haven't run across any other entries like on this or other sites.
View 1 Replies
View Related
Oct 2, 2012
We have 2 remote locations that are connecting to a server at our home location. Each remote computer uses quickvpn utility to establish a vpn with the home location. Our problem is that sometimes the vpn disconnects while we are working in remote desktop on server 2008. Luckily our sessions in remote desktop stay put but we lose the vpn connection. Most of the time we get a message that the remote gateway is not responding. Our dsl internet connection seems to work and we have previously had no trouble with connecting to the home location. We have 3 computers that connect simultaneously to the server at each remote location and sometimes one computer will stay connected while others disconnect.
View 3 Replies
View Related
Mar 1, 2013
I had both a Westell 7500 and a Linksys Router working fine and had my 360 setup as an extender for Windows Media Center so I could stream TV, Music, Movies, etc from my desktop to the 360. Then I switched my modem/router out with a Zyxel PH5001Z
So now today I noticed that I can no longer find my desktop through the XBox. I have adjusted my firewall settings on the modem itself, even completely disabling it. UPnP is enabled for the 360 and the device is showing under my device table. At first I wasn't able to ping any network devices but after creating an ICMPv4 Firewall rule it worked fine. I've confirmed the XBox IP Address through Network Map, the Device Table on the modem and through Network Settings on the XBox. I've diabled my modem firewall as well as Windows Firewall, completely and I still can't ping my XBox or set it up as an Extender.
I have the XBox connected wirelessly using WPA2-Personal and it's operating in 802.11g/n mode.
View 19 Replies
View Related
Jan 20, 2013
I'm looking to bring up a wireless bridge between 2 WET200.I've set in Wireless -> Basic Settings and Wireless -> Security the same parameters in both devices, but it fails.
View 13 Replies
View Related
Jun 10, 2012
At intermittent times, we will have a single device start to "hide" behind a 1242 bridge.In the past, my team would reload or reboot the bridge, and everything would come back up.But the 90 seconds of lost data were causing problems.
I found the the WB was always available.So I would ping the hidden device from the WB, and it would ping.Next, I showed the ARP table, and got the MAC address of the hidden device.Then, I would start a ping from my PC, and leave it running. Constant "Destination Unreachables" from the router.Next, I showed the bridging table for F0, and sometimes the device would be there, sometimes not. I would add a forwarding bridging entry manualy, and exit conf.
Showing the briding table would show the device, with a "P"ermanent age, but still no pinging.Finally, I would remove the forwarding briding entry, and pings would start within a couple of seconds.During these periods, outbound UDP packets will continue to be forwarded from the PC.So, my managers want to convert everything to UDP, which is a potential disaster in my opinion. [code]
View 12 Replies
View Related
Dec 11, 2009
I am interested in purchaseing a WET610N wireless Bridge for my new XBOX 360 to connect to my existing wireless, and wire network. I was wonder if the device can be connected to a 5 port network switch and used on multiple devices such as my TV.
View 5 Replies
View Related
Jun 17, 2012
I have installed 2 Cisco 1310's, connecting two buildings that are about 1000 yards apart. One access point is connected to an existing 3560 24 port switch, the other access point has a new 3560 24 port switch connected to it. Also installed 4 1240 access point in the newly connected building to the new switch. Issue is my router and existing switches can not ping any devices on the other side of the bridge. They can ping both access points that make the bridge. I consoled the new switch and could ping the existing switches and router, after doing that the other switches and router are now able to ping the new switch. Now my main issue is I have a user using a 7921 phone connected to one of the new 1242's, when he makes a call to a person in the first building they can hear him, however he can not hear them. Our call manager is in another state were I am located. I can call him and vise versa, and we can hear each other. I have went over my configs server times, and doubled check my IOS versions to make sure they are up to date. I will be glad to provide configs upon request.
View 1 Replies
View Related
