Cisco Routers :: WRVS4400N Router Unable To Login

Aug 9, 2012

Just installed a new WRVS4400N router.  wireless working.  however refuses to let me log back via Ethernet cable in at URL given me 403 Forbidden, Access Denies, Management via WLAN is not allowed.  Was able to reset and noe braodcasting unsecured "cisco b" signal, but no way to get into router and set up security.  unsure what I have done. 

View 1 Replies


ADVERTISEMENT

Routers / Switches :: Unable To Login To Asus Router?

Jul 31, 2011

I try to login to my router http://192.168.1.1/ I try and put in the user name and password that I think it is. Is it the user name and password you set up or one that's already there and if so where can I find it??

View 6 Replies View Related

Cisco Routers :: Unable To Combine RV016 With A WRVS4400N

Dec 2, 2011

I just installed a new RV016, and have it up and running currently using just one WAN (cable) on the Internet2 port. Just FYI I do plan to have a second WAN on Internet1 (DSL) once I get this next step working and want that to be the dafault provider, hence the use of Internet2 for this first connection.I already have a WRVS4400N installed that has a whole network on it that will be independant to the new the network and am trying to connect the WRVS4400N to my RV016. It is currently plugged into port 8 of the RV016 and the port is currently set to VLAN2.I know just enough to be a danger to myself here. :-) The RV016 is using the default IP of 192.168.1.1 while the WRVS4400N uses 192.168.10.1.I do know that "Typically, a Cisco RV0xx Series router is used as an access router, with a single LAN subnet. By default, the firewall is pre-configured to deny LAN access if the source IP address is on a different subnet than the router’s LAN IP address. However, you can enable multiple subnets to allow this router to work as an edge device that provides Internet connectivity to different subnets in your LAN."Hence I have added added the 192.168.10.1 subnet with mask 255.255.255.0 (to the RV016) and have tried switching the WRVS4400N from Gateway mode to Router mode. The RV016 can see it but nothing on the WRVS4400N network has any internet access, while computers on RV016 do. I assume this is because of the firewall blocking the traffic.

View 3 Replies View Related

Cisco Routers :: WRVS4400N - Unable To Access Admin Console

Jan 18, 2013

Although I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
 
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
 
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
 
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
 
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
 
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.

View 3 Replies View Related

Cisco WAN :: WRVS4400N - Can No Longer Access Internet Or Login On The Network

Oct 17, 2011

I recently bought a new Cisco WRVS4400N router for our network which has 19 computers connected to a 24 port switch.  We are currently using a D-Link router and are upgrading to the Cisco router.  The problem I am having is as soon as I connect one of our servers or the 24 port switch to the Cisco router I can no longer access the internet or login on the network, I also cannot access the routers setup from either server.  If I connect the router to just a stand alone computer I can access the setup and change things but as soon as I connect the server or 24 port switch everything dies (all lights are still green on the router though so everything is connected).

View 1 Replies View Related

Unable To Login Into Router Config Page

Feb 4, 2013

Basically all I want to do is login to my routers config page so that I can forward ports. I was able to this a few weeks ago but recently I have received this error. Failed to connect

Things that I have already tried:

- Tries using 192.168.0.1, 192.168.1.1, http://192.168.1.1 and all kind of variations.

- Tried with different browsers.

- Tried with seperate computer with different OS's (Mac and PC)

- Unable to flush dns because I get this error: CMD prompt error message .

- Have factory reset router a few times now.

- Unplugged, left off for 20mins-2hours.

View 16 Replies View Related

Unable To Login To Belkin F7d2301 Router

Mar 23, 2011

i cant login to my belkin f7d2301 v1 router tried fac reset

View 1 Replies View Related

Unable To Login Into Router To Setup Wifi

Apr 2, 2012

I just moved and have a new laptop, Comcast came in to reset the cable and internet. A new router was given to us and I cannot seem to access the password. I reset the router and now where to go nest since I try using the IP address and it is not recognizing it. I am using an unsecured WIFI access and I am not comfortable doing so.

View 1 Replies View Related

Linksys Wireless Router :: Unable To Login To WRT54G?

Jan 21, 2013

I am unable to login to my router ? I have tried to reset my router and am still unable to login to the online control panel. The steps that I went about resetting the router were pushing the reset button for 30 seconds. That did not work so I pushed the reset button for 30 seconds, unplugged the router while continuing to hold the reset button for 30 seconds, plugged the router back in while holding the reset for 30 seconds.

View 6 Replies View Related

Cisco Routers :: WRVS4400N V2 - Router Keeps Rebooting

Nov 28, 2012

I've got a WRVS4400N V2 Router that just keeps rebooting itself. It powers up, the red LED stays lit, it gets part way through the boot process and reboots itself. I would like to try to re flash the device, but don't know if this is possible in the condition that it is in.

View 3 Replies View Related

Cisco Switching/Routing :: Unable To Login Through Console Port On 1941 Router

Mar 12, 2012

I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
 
line con 0
exec-timeout 15 0
logging synchronous

[Code].....

View 5 Replies View Related

Cisco Routers :: WRVS4400N Router Vlans Not Working

May 28, 2012

the objective is to set up 2 vlans, one of which is a wireless access point connecting to our company network which is behind our firewall.  the other is a wireless access point for admins and selct people to connect directly to the internet, bypasing all network devices and firewall.  i am unable to get tech support unless i buy a contract for $800. I currently have it working and vlans setup but they both hook into the company network. 

View 3 Replies View Related

Cisco Routers :: Reset WRVS4400N Router IP Address And Password?

Jan 5, 2012

I have a conflict with my satellite Internet connection between the modem and router IP addresses. I also somehow entered a password for the router which I now cannot duplicate. received a request for additional information which I responded to in September. I attempted to follow-up in October again, but I have not received any reply since the first one on August 11, 2011.

View 1 Replies View Related

Cisco Routers :: WRVS4400N To Configure Computer On Router Page

Jan 9, 2012

I live in a house of about 30  tenants. The place uses a cisco WRVS4400N router. It seems that my  computer gets assigned a temporary ip automatically and then there will  be times when I get "kicked out" and my computer doesn't get connected  to the internet. Sometimes for few minutes and sometimes for hours.
 
No  idea what happens there but could be that there are no ips left to  assign to my computer and someone else gets the ip address.Anyway I'm trying to find out if I can configure my computer with a static ip.
 
The  maximum number of dhcp users was changed from 50 to 100 by me. IDK if  that means that I can assign a static ip from 1 to 100 but say I pick a  number 160 so the ip would be xxx.xxx.x.160.
 
1. What are the steps I have to undertake to configure my computer on the router page? What info. do I have to modify?
 
2. After I modify settings on the router page, do I have to change settings on my computer?

View 1 Replies View Related

Linksys Wireless Router :: WRT610n Unable To Login Config Page Via HTTPS

Jul 13, 2012

I'm having wrt610n and there is an issue, i can login to the config page via http, but using the same computer i'm not able to login there via https but the same time i can login via ipad and the other computer, using the https.i even tried to reset the router settings, but the result was the same, so what PC option can cause it?

View 6 Replies View Related

Routers / Switches :: Can't Login To Netgear Router

Apr 20, 2012

Cant log in to my router I've tried 192.168.1.1, 192.168.0.1, (url )Don't know what else I can try keeps poping up with search results. Oh, also tried reseting router and cable modem.

View 5 Replies View Related

Linksys Wireless Router :: WRT120N - Can't Accept Login Credentials When Login From IE10 Browser

May 9, 2013

 We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?

View 3 Replies View Related

Cisco :: Unable To Login After Upgrading To LMS 4.1

Dec 5, 2011

i recently upgraded our Ciscoworks LMS from 4.0 to 4.1. after i installed the upgrade the admin login doesnt work, neither does any other account. i have tried resetting the password but it doesnt work.

View 3 Replies View Related

Cisco Switches :: Unable To Login On SG-200-08

Apr 10, 2012

I configured a new SG-200-08 with a static IP. I tried to save the configuration as the startup configuration. After 10 minutes, I restarted the switch. It didn't boot with the new configuration, and returned to the default .254 and default pw. Now I cannnot assign a new pw or get past the change the pw page. When I try to save a new pw, the switch reboots and prompts me to change from the default pw. I tried resetting the switch by depressing the reset button for a long time, but results are the same. LED indicators are green with a flashing green indicating the .254 address and a solid green on the port where the switch is connected to the computer. How can I reset the switch or get passed the change your pw page?

View 3 Replies View Related

Unable To Login Into Switch?

Dec 3, 2011

if we are unable to login into switch how can we identify at which port of switch loop is there ?

View 3 Replies View Related

Cisco WAN :: Unable To Login At 6509 Switch

Jul 4, 2011

We are unable to login at Cisco 6509 switch, due to username and password not working. We have tried to recover the password as per Cisco document, but that is also not working. This switch is our Primary Switch in our network.

View 8 Replies View Related

Cisco Firewall :: 5510 - Unable To Login

Aug 23, 2011

I have not worked with ASDM in a while. I have a 5510, with asdm-645.bin in the flash. The device runs version 8.4(2).  I can download ASDM from the http interface of the firewall from the management interface. But I can not log in. I have used blank username and password, no username and enable password, blank username with enable password and a few other permutations. I then tried to connect to the asdm interface from inside also. But I can not connect. Needless to say, I have enabled http, and updated the http access-list.  The only logging I have enabled is buffered. Is there any configuration that I am missing? Shall I cut and past the config?

View 4 Replies View Related

Cisco WAN :: Unable To Use WLC 3750G Login-Page?

Jan 22, 2012

I have a WLC 3750 and use the web authentication method with the internal login-page. Now I would like to add a link to a PDF document which is supposed to be available before logging in. In other words: Clients connect to the W-LAN and get access to the login-page. They can download the PDF document (which has by the way a size of ca 10MB) from the login-page and after that they login to get access to the internet.
 
As far as I understood the manuals I won't be able to use the internal login-page because the size of a file is not allowed to be bigger than 1MB.So I thought about using the external authentication by using the webserver of my website. Unfortaunely the IP-Adress of my website doesn't work. Behind this IP-adress there's more than one website hosted. So I can't use my webserver either ...
 
Is there any other possibilty to add this PDF (size 10MB) on the login-page? Maybe I can add my website to a kind of a "pass through list" which is accessible even without authentication?

View 11 Replies View Related

Cisco Firewall :: Unable To Login In FWSM 3.2

Apr 13, 2011

I  am having two dc switches with FWSM modules installed. DC switch1 FWSM  (Ver 3.2(12) is wokring as active and Secondary DC switch2 FWSM (ver  3.2.(12) is in standby mode.
 
From  yesterday I am trying to login primary FWSM, It is accepting my  username and credentials but prompting again for username please refer  below
 
DXB-DC1>session slot 5 p 1The default escape character is Ctrl-^, then x.You can also type 'exit' at the remote prompt to end the sessionTrying 127.0.0.51 Open. [code]

View 1 Replies View Related

Windows 8 And IE 10 - Unable To Use Linksys Login?

Jan 28, 2013

I recently upgraded several of my systems to Windows 8 from XP. This, of course, included the update to IE10.Now, I cannot log into the router on my network via a Windows 8 system. It works fine if I use a Windows 7 laptop or an XP unit, but on Windows 8, when I go to the router's address, it prompts me for the Username and Password. It takes the password, and then immediately comes back and asks for it again. Another weirdness is that it won't exit when I choose cancel - only if I select the red X in the upper right corner of the authentication window.

View 5 Replies View Related

LAN Setup - Unable To Login To Computer

Feb 2, 2012

The computer that i am using which is on the LAN Setup. Also it is connected to the domain. Whenever i tried to log on to the computer it is giving me an error message that "The System could not log on the "Domain Name" either the connection is disconnected or the domain is no longer available" somting like that. When i remove the LAN Cable and if i enter the domain password, i can login to the computer. after i log on the computer if i connect the LAN Cable it is working fine. I can access the other computer which is connected to the same domain. Why the error message is poping up?

View 4 Replies View Related

Cisco Infrastructure :: C3560 - Unable To Login Through Hostname

Jul 4, 2012

I am unable to login to switch c3560 through Hostname but able to login through IP address. when i am putting the command : login authentication telnetpwd
 
getting the below message:
 
AAA: Warning authentication list "telnetpwd" is not defined for LOGIN.

View 5 Replies View Related

Cisco AAA/Identity/Nac :: 3560 - Unable To Login Switch?

Jul 5, 2012

I'm unable to login Switch.......getting following error...I have tried this commands on other 3560 that worked...when I enter user name & password  re logging authentication failed error occurs .........This is remote site Switch.

[code]...

View 7 Replies View Related

Cisco Firewall :: Unable To Login Through ASDM At ASA 5510

Jul 6, 2011

When i tried to login through ASDM at Cisco ASA 5510, it ask for the username and password and after that nothing comes up. I am able to login through ssh. [code]

As per my knowledge show bootvar and show version, should shows the same IOS version. But here it's showing different. Is asdm-523 is compatible with IOS asa708.

View 6 Replies View Related

TCP Window Size - Unable To Login To Application

Dec 11, 2011

We have a site where uses are unable to login to an application. After running a packet trace on the traffic coming from the site to the server they are trying to access, the trace indentifies that the client pc is sending a window size of zero to the server, and it does this twice. So in essence the client is saying it is too busy. This is strange as all the other applications work for the users and it is only this one application that is experiencing issues. The only other issue is that there is some retransmitted traffic before the client sends window size.

View 2 Replies View Related

Servers :: Unable To Login To Hotmail Account?

Sep 3, 2011

I can not access my hotmail account through msn.com, nor can I login to msn messenger as before. I get error message as follows:The requested URL /login.srf was not found on this server.Apache/2.0.59 (Unix) DAV/2 PHP/4.4.5 Server at [URL]Port 80

View 1 Replies View Related

Unable To Get Network Connection When Login Is Required?

Jun 15, 2011

when I try to connect to a network where is required a login in the first webpage I cannot have internet access, but only local access.I mean: even for free internet connection, sometimes they require you to connect to their network, then open the browser that is automatically direct to their network login page in order to login in that page.my problem is that I am able to connect to the network but when i open any browser, it does not direct me to the login webpage; it tries to go to my homepage but, obviously, the computer is not still connected to internet, so on the browser it appear "Atheros AR5B91 Wireless Network Adapter".

View 5 Replies View Related

D-Link DAP-1522 :: Unable To Login With Default IP?

Jan 5, 2012

 changed the router wan access pwd and now trying to test the dap i can't seem to log in with the default ip / dlinkap url access i have tried the bridge and ap switch setting on the dap with no luck after resetting the dap a couple of times with no luck ..

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved