After a few months of trouble-free ... the Cisco WRVS4400N V2 stopped working. i have tried to reset by holding the reset button for 30 seconds ... but nothing changes the red DIAG light remains on at all times
i have also tried two different versions of the Firmware Rescue Utility but all i get is "unable to scan"
I have been given the task of unbricking a WRVS4400N V2 router. It just sits there with the Power and Diag lights blinking and does nothing else.I'm thinking I'm going to have to try to find some way to flash the firmware, because I'm seeing that this is a common problem with this router.I already tried support "chat" online, but after about 20-30 minutes waiting for someone to actually come into the chat room, I gave up.I did note that this model is not being sold anymore and won't be supported before very long, so this may be a gigantic waste of time, but I thought I would give it a shot.
View 2 Replies View RelatedSo I went to update the firmware on my SA520 last night and aparently something failed, the device restarted and now it doesn't respond to anything. The Diag light stays light and the factory reset button does nothing no matter how long I hold it in. Is there another way to reset the device?
View 2 Replies View RelatedI am connected with qvpn, I can log in to the router bios remotely, but when I try to map the network drive from my remote location it does not work.I can detect the machine on the network, but it will not go further and tells me that "said IP was found but could not locate G". Does this mean it is behind a firewall on server side and that I need to create a rule to allow the incoming traffic? Or could it be something else.
View 1 Replies View RelatedMy ip address of my WRVS4400N changes every so often. when i use the ip assigned to connect remotely, it works until the ip is re-assigned through dhcp. I know there is a way around this bu ysing a name or something. I just don't know how to set that up.
View 1 Replies View RelatedI have a WRVS4400n and a CentOS server that I need to enable a SSH access to from WAN. I created a single port forward rule to open port 22 and forward to server (which address is 192.168.41.3) However ssh connect doesn't happen, the command "ssh user@{external_IP}" times out after 20 seconds. If I connect my server directly to modem through outside interface - I have no problems connecting to it. Once it's behind router - no luck. I even added same rule for UDP, not sure if it's needed, but it definitely didn't hepl. The router is on firmware version 2.0.1.3, version on a bottom is 2.
View 4 Replies View RelatedI have a WRVS4400N, and need to apply access control to an IPSec tunnel that terminates at a client site, but can't seem to make the device comply.
I can configure ACLs on their device for the LAN to restrict packets coming back into my network, and can restrict packets outbound frm my LAN but that is hardly a secure method of doing this in my opinion.
After updating the firmware of my WRVS4400N from V 2.0.1.3 to 2.0.2.1 all traffic was blocked for all machines, even some not included in the list of PCs. As the log was showing that all traffic was blocked by access policies, I disabled the only rule I had (blocking access to some sites to some MAC address list) and everything worked fine.I tried creating a new, simpler rule but after activation it blocked again all traffic for all the LAN.After many trials, I decided to roll back to the previous V2.0.1.3 which solved this problem.
View 1 Replies View RelatedI am trying to create an IAP for a single computer based on it's MAC address. I want to block certain keywords and websites 24/7. When I setup the IAP as number 1, I add the MAC address of the computer in question. I then Select Allow and choose Everyday and 24 Hours. I type in the forbidden domains and click add after each one. I type in the keywords and click add after each one. After I click on Save, all of my computers on the network lose internet access.
I have WRVS4400N VPN Version 2, firmware version 2.0.2.1
I recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever. However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
I have:reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.Tried to move the router close to the laptop, no difference.
Although I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.
When clients connect wirelessly to the WRVS4400N they successfully get a DHCP address from the Windows 2008 server. After they have the address they can no longer access the server. It cannot be pinged, no drives can be mapped and internet access fails because the same server is running DNS. The WRVS4400N is setup for DCHP relay to the server. Wired clients do not have this problem. Wireless clients that connect to a secondary WAP on the same LAN also do not experience this problem. I have updated the router to the latest firmware version, reset it to factory defaults and reconfigured from scratch. Turning the server firewall off has not made any difference either. I have been able to bypass the internet problem by adding a second external DNS server in the DHCP scope options.
View 5 Replies View RelatedAfter inserting a RSP720-3C-10GE in module 6 and running the show module command display the following [code]what is the meaning of the UnKnown on the oline diag status ?
View 1 Replies View RelatedWe recently installed a WS-X6716-10GE module in slot 6 within a Cisco 6506. We are using two ports on the module (6/13 and 6/14), which are port channeled together to a Nexus 5548. Everything has been running fine for about a month and the card had a green light but the ports stopped communicating. The module was screwed into the chassis/slot. For problem determination reasons, we reconfigured ports 6/13 & 6/14 to 6/15 & 6/16 and moved the cables but the module was still not responding. We eventually pulled the module out of the slot and reinserted the module back into the slot, which reset the module and fixed the problem. Is there any way to determine if this was hardware problem with the module and it should be replaced, or is it a software bug/problem? We opened up a ticket with the TAC but we haven't heard back from them yet.
Cisco WS-C6506-E
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(33)SXI8, RELEASE SOFTWARE (fc2)
Mod Ports Card Type Model
--- ----- -------------------------------------- ------------------
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B
6 16 CEF720 16 port 10GE WS-X6716-10GE
[code]....
Is it possible to reflash the firmware on a BEFW11S4 (I believe v1, there is no v# after the model number) with a solid red Diag LED? I cannot access the HTML control panel since the router never fully boots. I git this used and didn't know it was **bleep**..
View 2 Replies View RelatedRight out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?
View 2 Replies View RelatedI'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up. I am unable to add a default route to the 4400n's DHCP server. It uses the 4400n's vlan IP as the default route. What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.
View 12 Replies View RelatedI'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
Ive setup a few WRVS4400N over the past 6 months, and have been receiving the below message from some of them every couple of hours.What does the message indicate?
View 1 Replies View RelatedI have successfully got QuickVPN working from Windows 7 64bit into my WRVS4400n. The router is sat behind another router/modem (Belkin) as the UK uses PPPoA and the WRVS4400n doesn't.So I set up DMZ and changed the DHCP to always allocate 10.x.x.2 on the Belkin which is the WAN side for the WRVS4400n as it is the only thing attached.I have now noticed, and I'm not sure whether it was the case before, that the DNS that the WRVS4400 is showing is the LAN address for the Belkin Modem/Router (10.x.x.1), not 192.x.x.1 for the WRVS4400n itself. I assumed setting the Static DNS 1 on the WRVS4400n would do it, but it didn't?When I connect into the network with QuickVPN, the computer names do not show even though I have selected the option in QuickVPN?
View 1 Replies View RelatedOur business was looking at purchasing one of these Cisco routers and were curious if it supported WPA2 EAP-TLS?
View 2 Replies View RelatedI have 2 WRVS4400N's available to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies View RelatedRecently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.
Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.
Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.
I have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.
I'm having a heck of a time connecting the WRVS4400N VPN to another WRVS4400N VPN. both of the routers have the current firmware version V2.0.2.1: Router 1 is below, and router 2 has the matching configuration with as it should be the local group being that routers local information and the remote crew set up being router ones information. the status is up on both of the routers, but I'm unable to ping the remote gateway or any device behind it.[code]
View 5 Replies View RelatedHow to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP.
This is a new device, just initially installed about a week ago. I updated to the latest firmware. We have iphones, ipads, and Samsung Galaxy smartphones all trying to connect to this WAP at this office, but cannot seem to connect. If I power cycle the WAP, we can connect for about 5 min, then it loses it and cannot connect again. I have strong signal, device says "connecting" then immediately "disconnected"... does this on loop forever.WPA/WPA2 PSK.I don't know what to do. About to go buy an Apple WAP.
View 3 Replies View RelatedMy WRVS4400N is not letting my VPN client through the router. I have checked the passthrough boxes for all 3 protocols. I have port range forwarding for my VPN connections to my SBS2008 box on port 1723.
View 5 Replies View RelatedI have a Linksys E4500 as the main router and would like to use the WRVS4400N as a bridge to extend the range of my network and also attach a NAS to it. Is this possible? I've been trying different options but have been unsuccessful.
View 1 Replies View RelatedLooking for a working Cisco VPN client for Windows 7. There seems to be an availabel download for a ver 5, but you have to be a reseller etc.. Where do I download the Windows 7 supported VPN client to access my WRVS4400N router? If none, should I use 3rd party - IF yes to 3rd party, which one would you suggest?
View 1 Replies View RelatedI bought a WRVS400N v2 to be used as an access point. Currently it is hooked up on my switch via a trunk port and is able to communicate with my gateway. Whenever I try to access an IP subnet other then the local IP address of the WRVS, I get a network unreachable error. To fix this for my local networks, I added the appropriate static route to cover my local LANs and that seems to work now. I tried to add route 0.0.0.0/0.0.0.0 using the web interface for internet access, but somehow it does not recognize this as a default route (quad zero!?). Does any know how I can set the default gateway in this router? Maybe, but hopefully not, I have to use the WAN port to create some kind of uplink and use one of the LAN ports to connect using the trunk port and route traffic for the clients over the WAN port .
View 1 Replies View RelatedI have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
I have looked through the forum for answers to my problem, but does not look like I'll find it.The problem: Router randomly freezes.When this happens:No IP/DNS,No response to ping,No contact at all (wifi or cable),Works fine after reboot for some time.
View 2 Replies View Related