Cisco Routers :: Windows RDP Remote Desktop Not Working With WRVS4400N

Nov 16, 2010

I use RDP extensively on my LAN to use and manage 4 PCs running Win XP or Win7. My consumer-grade Cisco Linksys WRT610n crapped out after less than 2 years, so I thought I'd try the Cisco WRVS4400N to gain extra features like VPN. I have not enabled anything new on the router except for adding a second wireless SSID for guest use, although no bandwidth management or VLANs have been set up yet. Firmware version is 2.0.0.8.Since installing this router I have been unable to use Windows RDP on ANY of my computers on the LAN, whether I use the machine name or the IP address. I can ping every device on my network - print servers, NAS boxes, PCs, but no RDP. WHAT'S GOING ON?

View 6 Replies


ADVERTISEMENT

Cisco Routers :: WRSV4400N / Remote Desktop Through Windows VPN?

Mar 24, 2013

We have a WRSV4400N installed as our primary NAT Firewall.  It is configured to allow Windows VPN connections to our server residing on the Internal Network Domain - this works fine.Problem is that even though the remote VPN client can open shares, browse the internal network, and resolve computer names fine with DNS,  but... Remote Desktop will not connect using the VPN tunnel.We need this to work... I spent several hours with your support people when installing this router a year ago and got nowhere.  And everythung else works fine.I am using Windows server-based VPN because your VPN Clint didn't work ata ll either. Can you perhaps give me a list of configuration settings to check?

View 3 Replies View Related

Cisco Routers :: Using Remote DNS With QuickVPN - WRVS4400N

Dec 11, 2011

I've deployed a WRVS4400N router at one of my clients, however I'm unable to access resources on his network via DNS. I was hoping to use the router for DNS resolution, however when I connect via VPN, I can only connect to shares via IP address.

View 1 Replies View Related

Cisco Routers :: WRVS4400N V.2 - Remote Management Through The Firewall

Mar 21, 2012

I'm attempting to configure remote management (and, sometime soon, SNMP) for a newly-deployed WRVS4400N v.2.At the Basic Settings page, I enabled Remote Management, and left the port # at the default. Remotely I entered the public (static) IP for the router in the address bar of IE8 similar to this: 67.203.???.??:8080. IE8's response is, "The webpage cannot be displayed." I'm using a public wi-fi access point, and don't know how the local router is configured, so it's possible that the local router has a blocking rule in the firewall.I'll try again using another remote router that I manage.

View 3 Replies View Related

Remote Desktop Not Working From Outside Of Network?

Feb 17, 2011

So i'm trying to set up remote desktop connection for my desktop at (xp pro, sp2).

I've went through all the steps:

- allowed users to connect remotely (system properties)

- added to firewall exceptions

- opened up port 3389

I've disabled firewall and virus protection for now as well to test.

It works fine when I try connecting from my laptop at home by opening up the remote desktop program, and entering the local static ip address that i've configured on the desktop (i.e. 192.168.x.x);

however, when I try to connect outside of this network (on the road or office), I can't seem to connect (yes, I replaced the ip 192.168.x.x with the public ip of the desktop which I got from whatsmyip.org). I also can't ping the public ip of the desktop (can only ping the 192.168.x.x ip of the desktop)

Again, router port is open to port 3389, firewall is turned off on both the desktop and laptop, and virus protection is off.

View 10 Replies View Related

Remote Desktop Stopped Working

Mar 30, 2012

My computer stopped being able to Remote Desktop to my server on my network. My backup software also doesn't recognize my server. But, I can access its folders using Windows Explorer. Any other PC on the network can remote desktop to the server and connect. What happened to my machine? This message appears when i try to connect: "Remote Desktop can't connect to the remote computer for one of the following reasons:

1) Remote access tot he server is not enabled

2) The remote computer is turned off

3)The remote computer is not available on the network

Make sure the remote computer is turned on and connected to the network, and that remote access is enabled."

My computer is:
AMD: Athlon 64 X2 5200+ 2991 MHz
Mobo: Gigabyte M57SLI-S4 v.2
RAM: 4GB Mushkin DDR2 PC2-6400
OS: Win 7 64bit
VC: Geforce GTX 470

View 1 Replies View Related

Cisco Routers :: WRVS4400N And Quick VPN (remote Gateway Not Responding)

Jul 27, 2010

Router is a version 1.1 running with sw version V1.1.13-ETSI
Quick VPN is sw version Ver 1.4.1.2
 
The issue is that I can't connect due to that i cant ping the internal IP, get this error message in the QVPN log  [WARNING]Failed to ping remote VPN Router![URL]I have disable the "Block WAN Request" and it is possible to ping the router on the external site.So as I see it, the router blocks for ping on the internal IP via QVPN, what have I done wrong?

View 20 Replies View Related

Run Remote Desktop Client Using CAT 5 Crossover Isn't Working

Aug 9, 2011

Attempts to run remote desktop client a laptop on a tower using a CAT 5 Crossover isn't working. After starting the remote desktop on the laptop, I'm asked to identify the other computer, which I do, and a remote desktop window with a black background pops up, as expected. But I expect an opportunity to login will be displayed after a second or so. That never happens. After about a minute this pops up:Remote Desktop Disconnected?Your Remote Desktop session has ended.The connection to the remote computer was lost, possibly due to network connectivity problems. Try connecting to the remote computer again. If the problem continues, contact your network administrator or technical support.

My clients are impressed with my ability to setup their networks, Linksys routers with WIFI. But toss something unfamiliar into the mix, like this situation, and I'm pretty lost, pretty quick.

Environment:
Hospital's WIFI.
Laptop running XP Home with WIFI and Ethernet.
Tower running Win 7 Ultra with Ethernet.
Cat 5 crossover cable.

Goal:Configure laptop to access Hospital's WIFI. This is successful, I'm using it to post this. Configure laptop run a remote desktop with the tower as the server. The tower, running Win 7, has no monitor. I don't have a flat screen monitor, and didn't feel like dragging an 80 pound 24 inch Nokia into the hospital.After reading some sites while trying to figure this out, I gave the laptop the same group name, workgroup, as the tower.In my experience, starting the tower has been, turn it on, and it boots to Win 7. But I can't watch that happen without a monitor. I can't configure the the tower's network connections without a monitor either.I purchased the CAT 5 crossover cable yesterday, for this occasion. The label on the plastic bag it was packaged in had the word "Crossover" on it. I connect the CAT 5 to the laptop's single ethernet connection, and to the tower's Intel pro card. At home the laptop is on WIFI, the tower connects to the router.

View 4 Replies View Related

Can't Get Remote Desktop Working In Work Environment

Oct 4, 2011

I'm trying to use RDC to connect to my home PC from work. I've tested everything on my laptop from another network and the connection works fine but the same settings don't seem to work when I'm at work.

I'm pretty sure I have everything set up correctly. Using the default port forwarded to the desired computer.

View 1 Replies View Related

Remote Desktop Connection Between Windows 7 And XP?

Dec 5, 2012

I want to setup Remote desktop connection between PC's running win 7 and win xp so that i can access win xp machine through win 7. Both are connected through LAN connection.

View 2 Replies View Related

D-Link DIR-825 :: Remote Desktop In Windows 7?

Nov 15, 2009

configure this router to allow connections from the internet for remote desktop?  I can do it on my lan, but the Dir-825 blocks this feature.  Yes, I set up port 3389 as a virtual server to the computer I wish to use. 

View 6 Replies View Related

Cisco Routers :: WRVS4400N VPN Pass Through Not Working

Sep 18, 2011

My WRVS4400N is not letting my VPN client through the router. I have checked the passthrough boxes for all 3 protocols. I have port range forwarding for my VPN connections to my SBS2008 box on port 1723.

View 5 Replies View Related

Free Remote Desktop Software For Windows 7?

Apr 12, 2013

Boss has asked me to find a "free" Remote Desktop App, to monitor, access and audit over 200 workstations

View 6 Replies View Related

Can't Remote Desktop In From IMac Into Windows Machine

Feb 9, 2012

I have a Win 7 machine with Win SBS 2011 in my office and an iMac. The Win machine is being setup for Exchange 2010. My problem is this: I can't Remote Desktop in from my iMac into the Win machine, but CAN when outside the network.The Win7 machine has a static IP, the iMac a dynamic. When I access the internal part of my router I can only see my iMac. I get a "can't connect to win-based machine" error when I try to Remote Connect.The only thing I can think is that using the same gateway is somehow messing things up? I've had two techs try to figure this out and they're both stumped.I was maybe thinking that since both comps are going out the same gateway that I should try anc configure the iMac to try and RDC on a different port, since maybe the iMac is listening on 3389 and sending the RDC back to itself?

View 4 Replies View Related

Cisco VPN :: ASA5510 - Windows 7 Connects To It But Not Remote Desktop

Mar 15, 2010

we just got several laptops that came with Windows 7 Pro 32bit installed, and we have installed the VPN Client 5.0.06.0110.  The VPN client appears to connect to our ASA5510, but we are unable to connect to any machines on our network as it does on our XP machines. 

Furthermore, we cannot ping any as well.  Also, while connected the Windows 7 machine is still able to access internet site as if split-tunneling was configured, which its not!  I've seen alot of people posting on the internet about the same issue, but I have not run into any resolutions that work.

View 14 Replies View Related

Sharing :: Belkin N750 New Router - Remote Desktop Connection Not Working?

Jan 20, 2012

I have recently upgraded my router to a Belkin N750 DB and am having issues getting remote desktop connection working. Previously I had a Netgear router and it was working no problems at all.I have port forwarded (virtual server on Belkin) port 3389 TCP to the servers IP address.I can get Remote desktop connection to work when I am within my LAN by just typing the computers name.However when I try to connect via the IP address, as I would if I were away from home, then I get the message that says "remote desktop cannot connect for one of these reasons

1) remote access not enabled (it is because it worked before)
2) remote computer is turned off (no it isn't)
3) remote computer is no available" (yes it is cause can connect from LAN)

Turned off static IP for my server and let the router assign IP, and changed the IP address in the port forward, same, no connection.Double, triple checked my IP address, as this obviously changed when I plugged in the new router.Have updated to latest firmware for router and NIC.

View 14 Replies View Related

D-Link DIR-655 :: After Upgrading To Firmware 1.35 Remote Desktop Not Working On Home Network

Mar 22, 2013

I was using Remote Desktop between two home computers hard wired through the router and a switch.  Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc.  I have the DIR 655 ver A and am running Windows 7 professional on both computers.

View 5 Replies View Related

Cisco Routers :: WRVS4400n & WPA2 Not Working On Xbox?

Jul 23, 2011

So got an Xbox 360 slim and if I try to connect to route with WPA2 if fails. If I change to WPA or set up a second SSID with WPA it connects and works fine.If I connect Xbox to another router with WPA2 it works fine.Same results picking AES or TKIP for security type.The xbox is used in a break room and really don't like the fact that I need to have another ssid and it be less secure, esp as WPA2 has been out long enough this shouldn't be an issue. I test 4 other routers and WPA2 and xbox all work fine but not this one but this is the one I have to use due to feature needs.

View 16 Replies View Related

Cisco Routers :: WRVS4400N Router Vlans Not Working

May 28, 2012

the objective is to set up 2 vlans, one of which is a wireless access point connecting to our company network which is behind our firewall.  the other is a wireless access point for admins and selct people to connect directly to the internet, bypasing all network devices and firewall.  i am unable to get tech support unless i buy a contract for $800. I currently have it working and vlans setup but they both hook into the company network. 

View 3 Replies View Related

Allow Remote Desktop Connections In Windows Server 2008?

May 10, 2011

Is there any way to allow multiple computers to connect to the same remote computer and work simultaneously?

View 3 Replies View Related

D-Link DIR-655 :: Utilize RDP (Windows Remote Desktop) Between Two Points

Jun 10, 2013

I recently purchased (2) DIR-655 routers; one for home and one for the office. Both are connected to the 'net through CenturyLink DSL via a Zyxel 660 modem.I am switching from a Cisco/Linksys WRT54G home and a Trendnet TEW432BRP at the office. I wanted to get up to N and consolidate to a single hardware type. The 655 came highly recommended, and the price was right at $75.My goal is to utilize RDP (Windows Remote Desktop) between the two points and from other points inbound to either 655. The first hurdle was that the Xyxel modem, by default, blocks just about everything inbound with no hope of opening the ports. The only viable solution was to bridge the modem and allow the 655 to act as DHCP. Done. The modem now should not even have its own IP address, and should completely bypass all of the built-in firewalls, etc. As soon as I went into bridged and forwarded the ports in the router we were in business (though I still can't seem to log in to RDP, the ports are verified open).

View 6 Replies View Related

Cisco Routers :: WRVS4400N Internet Access Policy Not Working

Jun 23, 2012

I am trying to create an IAP for a single computer based on it's MAC address.  I want to block certain keywords and websites 24/7.  When I setup the IAP as number 1, I add the MAC address of the computer in question.  I then Select Allow and choose Everyday and 24 Hours.  I type in the forbidden domains and click add after each one.  I type in the keywords and click add after each one.  After I click on Save, all of my computers on the network lose internet access.
 
I have WRVS4400N VPN Version 2, firmware version 2.0.2.1

View 2 Replies View Related

Cisco Routers :: WRVS4400N Stopped Working With VOIP Phone

Mar 1, 2013

I have the router for over two years, Present Firmware is V2.0.1.3, I have Polycom phone connected to the router using 8 x 8 VOIP service. The phone was working fine untill yesterday. 8 x 8 tech support suggested getting a different router. I have the same router at home and tried the same phone on my home router - it worked. So, the problem is not the phone but int he router. I tried to call Cisco tech support but found out that the warranty support expired and I need to buy a support plan. Called to buy the support, and gave up after an hours on hold. Left  message.

View 1 Replies View Related

Unable To Start Remote Desktop Services On Windows 7 Machine?

May 2, 2012

If I am not able to start remote desktop services on windows 7 machine, will machine can be accessible by RDP?

View 1 Replies View Related

Cisco Routers :: WRVS4400N VPN Client For Windows 7

Feb 14, 2012

Looking for a working Cisco VPN client for Windows 7. There seems to be an availabel download for a ver 5, but you have to be a reseller etc.. Where do I download the Windows 7 supported VPN client to access my WRVS4400N router? If none, should I use 3rd party - IF yes to 3rd party, which one would you suggest?

View 1 Replies View Related

Routers / Switches :: Remote Desktop Access From It?

Mar 7, 2012

how can I remote in to my router and I need to get past my router to my pc desktop

View 2 Replies View Related

Cisco Routers :: WRVS4400N Connecting To Windows Network

Jan 20, 2012

I put just got a wrvs 4400N and when I replaced my old linksys router I can't access my network computers anymore.  I'm I missing something or do I need to do some kind of setup?

View 3 Replies View Related

Cisco Routers :: WRVS4400N - VPN Blocking Windows Services

May 15, 2012

I need to access a shared folder over a VPN connection. Very simple host network: no Microsoft server, no AD. Just a WRVS4400N router and a peer-to-peer network.
 
Purchased a second WRVS4400N router to create VPN from SOHO and configured via VPN Setup Wizard.
 
When at the office, I can map a drive letter to a share on the other computer, as follows
 
net use f: \192.168.1.111MyShare /User:MYSELF mypass
 
However, when try same command over VPN, I receive the response:
 
System error 53 has occurred. The network path was not found.
 
I also cannot net view the other computer -- same error. However, I can successfully ping 192.168.1.111.
 
More info:
 
Routers have latest firmware.
 
Over VPN I cannot browse network via Windows Explorer (Win7 Network Neighborhood shows only my own PC. In the office I can see the other computer and the NAS appliance "NAS01").
 
I also cannot connect by entering \192.168.1.111MyShare into Windows Explorer's address bar (although I can do that successfully when at the office), or by choosing Map Network Drive from "Computer".
 
However, over VPN, I can get into NAS administration via https://192.168.1.3 and I can print to the office TCPIP printer (192.168.1.222)

View 4 Replies View Related

Linksys Wireless Router :: E4200 Blocking Windows Remote Desktop Connection?

Mar 7, 2012

I just picked up the E4200 to replace a router, I can remote desktop into a computer that is physically connected to this router, but cannot remote desktop into other computers on the network that are connected via another switch.

View 1 Replies View Related

Cisco Routers :: RV220W Upgrade To 1.0.4.17 - Now Remote Desktop Won't Connect

Sep 16, 2012

Or rather, it will connect within the first few minutes after a router reboot, but eventually is kept from connecting.
 
All settings look good. Upgraded from 1.0.3.5.  Prior to upgrade, this was not  problem.

View 3 Replies View Related

Windows 7 / Unable To Connect To Desktop - Other Devices Working

Aug 21, 2012

I'm running Windows 7 on my desktop, and I've had problems since yesterday with my pc. My Vista notebook, ipad3, ipod touch, android based phone and blackberry are all able to connect to the wifi, but my desktop is unable to connect to the wifi or ethernet. Things were working fine until yesterday, when I had to power cycle, after which the desktop connection stopped, though other devices are working fine. My ipconfig details are as follows:

Windows IP Configuration Host Name . . . . . . . . . . . . : DELL-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : reliancebroadband.co.in

[code]...

View 2 Replies View Related

Cisco Routers :: RV220W Remote Administration Not Working

Oct 26, 2011

RV220W is at firmware v1.0.2.4 From: Administration / Management Interface / Web Accesss I have configured remote Management: Remote Management [x] EnabledAccess Type: All IP addressesPort Number: 8888Remote SNTP  [  ] not enabled
 
From within the LAN side I can connect to the router and administer via https://192.168.3.97:8888
 
Status / System Summary reports:WAN (Internet) Information (IP4)
Connection Type: Static
Connection State: Connected
IP Address: 207.180.139.242
NAT:  Enabled
But from the WAN side (using the same Win7 computer) I cannot connect via:  https://207.180.139.242:8888
 
This used to work.   Also not working:  PPTP logins.   ISP is RCN via cable modem, fixed IPs.
 
Have tried power cycling router - no luck. Have tried from PC with AV off and Win7 firewall off

View 5 Replies View Related

Cisco Routers :: RV042 After Configuring DMZ / Remote Management Stopped Working

Sep 30, 2012

I have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:

- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
 
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved