Cisco Security :: Dell Latitude D820 - Reason 442 / Failed To Enable Virtual Adapter
Feb 5, 2007
I've installed version 4.8.02.0010 of the VPN client onto a Dell Latitude D820 laptop. When I attempt to connect, I get this message. There are no firewalls running (I disabled the Windows XP firewall) and I'm running under Service Pack 2 with all of the latest security patches from Microsoft.
I even tried un-installing the client and using an older version (4.8.00.0440) and it reports a similar error in the Log file.
I'd prefer to NOT have to wipe the laptop and reinstall the O/S if I don't have to. This is the only laptop that I've experienced this problem with but it's also the first Dell Latitude D820 that I've attempted to install the client on.
Is there a problem with the Dell Latitudes and the VPN Client? Is there another way around this other than a wipe and re-install?
View 3 Replies
ADVERTISEMENT
Oct 26, 2011
I have a Latitude D820, Windows XP, SP3. At my office I have a regular docking station but at home I have a D/Dock docking station. When I dock the 820 at home the Broadcomm network card works flawlessly. When I dock it in the office, it will occasionally work but most of the time the link light and data light on the docking station are on solidly and XP reports that the cable is unplugged. I have tried two different docking stations with identical results and also tested the cable by plugging it into the docking station that holds a D810. With the D810 it worked normally.
View 1 Replies
View Related
May 15, 2011
ASA error message: 16/ERROR: Unable to start VA, setup shared queue, or VA gave up on shared queue.Win 7 x64 client says: "The VPN client driver encountered an error. Please restart your computer or device, then try again."Client Event Log (AnyConnect): "The VPN client has sent the following close message to the gateway: Unable to start VA, setup shared queue, or VA gave up on shared queue."ASA 5510 running latest 8.41(1) and ASDM 6.4(1). Client is latest 3.0.1047.
View 2 Replies
View Related
Dec 19, 2011
My son was using the computer early today and I got back on and could not get on the internet.Says "Wireless is turned off. Use the wireless ON/OFF switch to enable it" i have tried the Fn+F2 and just F2. I also tried looking for Quickset and I cannot find that either. Saw similar problems looking through other forums but I don't understand much about computers and can't quite figure out what the solutions are. I have a Latitude D620.
View 3 Replies
View Related
Jan 5, 2010
I've been trying unsuccessfully for weeks to find out how to turn on the Bluetooth adapter (turn Bluetooth radio on) on my Dell Latitude D620.
Firstly does the D620 have a built in Bluetooth adapter? I've done a search on the web and it appears it does. Also I see a Bluetooth symbol just above my keyboard, but it is not lighted up. How do I turn it on?
I went to Control Panel, Device Manager -> Network adapters, but I don't see any Bluetooth devices listed there.
Do I need to install some software? I went to support.dell.com and downloaded the installer for Dell Wireless 350 Bluetooth Internal Module driver. But when I install it, it is tries to install the Vista Profile Pack, and it fails because it "Could not find compatible bluetooth chip on your system" and "DFU install failed with returncode 137".
View 8 Replies
View Related
Oct 6, 2009
I have a laptop DELL Latitude E6500. I cannot connect it to LAN through Intel (R) 82567 LM Gigabit Network adapter. Connection is set up by DHCP. I get error message: "cable is unplugged", but cable is functional. How I can resolve this problem?
View 1 Replies
View Related
Oct 22, 2011
I have a Dell Studio Laptop 1737 with Dell Wireless 1397 WLAN mini-card and Windows 7 home premium 64 bit. Some days ago, I bought a HP WiFi mouse (model LQ083AA). This mouse connects via WiFi and you need no USB-port for a transmitter. Very practical - if it would work probably.First I installed the SW delivered with the mouse. During this installation, also the "Microsoft Virtual WiFi Miniport Adapter" was installed. The mouse connects via this adapter. And everything worked fine. The mouse was found, a connection was established and the mouse worked like a charm. Until I went to sleep. As usually, I hibernated the notebook. And after waking up the notebook from hibernate, the mouse did not work anymore. I found out it is because the "Microsoft Virtual WiFi Miniport Adapter" does not wake up correctly. After a reboot, everything works again. And if I use the HP software to reestablish the connection, I receive the error "SoftAP is not available".
I tried several things:I un-installed the "Microsoft Virtual WiFi Miniport Adapter" in the device manager and checked for new HW to install it again. But after it was installed again, it still did not work.In the device manager, I disabled "Microsoft Virtual WiFi Miniport Adapter" and enabled it again - but it stayed disabled.I updated the driver.I changed energy management, allowed the computer to switch of power of the adapter resp. disallowed that.Nothing I did worked. After hibernate, the "Microsoft Virtual WiFi Miniport Adapter" is "dead". Only a reboot works.The WiFi mouse is such a great Idea, but the "Microsoft Virtual WiFi Miniport Adapter" is such a mess.
View 3 Replies
View Related
Mar 10, 2012
I haven't installed anything new lately, nothing that would affect the wireless, but my wireless suddenly stopped working. My wireless has been working successfully for the past 2 years no problems till now. I have a Dell Latitude E6410 my computer is running Windows 7 32bit. When I open up the DW WLAN Card Utility it says "There are currently no wireless adapters available and enabled. Please enable any available wireless adapters before accessing this configuration utility. I tried reinstalling drivers for the wireless but my computer says "no compatible hardware found".
Also the under the wireless adapters section of Device Manager there isn't an adapter for wireless, but there is an unknown device.
Here's a View at my Device Manager [URL]
I've tried to use computer restart magic but no luck there.
Also, my computer is running on a university network. My roommate's wireless is working fine. Also I've already system restored to a point where I know it was working, no luck...
View 2 Replies
View Related
May 28, 2012
We have a user using a Latitude D820 running Windows XP. It's a slow machine, but it's been working generally fine up until yesterday, when it started having connection issues.
When connected via an ethernet cable, the laptop can connect to everything on our internal network (fileserver, Exchange, internal websites), but anything outside (Google, other websites) is inaccessible (Internet Explorer cannot display this webpage). External sites will then be accessible after a few minutes, then connectivity will be lost in about another 5 - 15 minutes. This process repeats seemingly endlessly. We've replicated this in separate offices, so it's not the wiring. And everything works fine running off of the wireless.
Things we've tried:
Disabling the 1394 Connection
Disabling the wireless connection
Disabling all non-LAN adapters
Restarting the computer
Disabling/re-enabling the LAN connection
Updating the network card drivers
Resetting IE's settings
Cleaning out the user's temporary internet files
Logging into the machine as a different user (local administrator)
Things we know aren't causing the problem:
Firewall
Antivirus
Our network
Proxies
View 1 Replies
View Related
Jul 27, 2010
I have a 5 month old Dell Inspiron 1564 with a Dell WLAN 1397 Wireless card. I was having some trouble connecting to my wireless router, and as a last attempt to get it working, I uninstalled and reinstalled the driver for my wireless card, using a fresh download of the latest version from Dell's support site.
The driver seems to install fine, and when I look at the wireless card in Device Manager, it's enabled, but in "Control PanelNetwork and InternetNetwork Connections" (which can be accessed through the Network and Sharing Center), it is grayed out and says Disabled.
When I click enable in there, a small window pops us saying "Enabling", then after a few seconds, it says "Enabled" then disappears. However, the adapter stays disabled in N/W & Sharing center, and isn't picked up by Windows.
I've tried reinstalling the driver through Dell's driver installer, as well as through Windows' automated driver search, and neither works. I also tried to do a System Restore, but that is not working (can't complete on any of the restore points).
I also spent 1.5 hours on the phone with Dell support and their final advice was format and reinstall Windows.
More details:
- I am running Win 7 Pro.
- Wired networking and internet connection works fine
- I have Zone Alarm and Avast Anti virus, and I've tried disabling both to no avail
View 8 Replies
View Related
May 10, 2012
I am trying to add an AP (1231G) with autonomous code (Version 12.3(8)JEC2) to WCS (v7.0.172.0). I recieved the following error:
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.
View 9 Replies
View Related
Jul 18, 2010
here about it : [URL]
To reinstate here. It is a refurbished notebook. I don't know if that has anything to do with my problem. But there is no wireless on/off switch. And pressing FN and F2 at the same time is not enabling my wireless adapter. Is there any way to enable it? Or could I have a faulty wireless adapter?
View 6 Replies
View Related
Feb 2, 2012
I recently re-installed the driver for the 1390 WLAN Mini Card after not having wireless for a few years, and have a few problems. In the Windows XP Home Network Connections folder, the Wireless Network Connection Icon shows, "Acquiring Network Address", but never gets past that. I ran a diagnostic in the "Dell Wireless WLAN Card Utility" and the card passed all the tests, even though with the card switch in the on position the LED doesn't light (??)
When I right click on the Wireless Network Connection Icon and choose, "Status", in the "General" tab I can see that the card is sending out packets, but none are being received. In the "Support" tab under "connection status" the following appears: "Address Type": Invalid IP Address, "IP Address": 0.0.0.0, "Subnet Mask": 0.0.0.0, "Default Gateway": (nothing listed).
Background: I have a Desktop (no brand) and the Dell D820 connected with a Westell Modem and a D-Link WBR-1310 Router. Both computers work great connected to the Router with a cable. Both computers are running Windows XP Home.
The only thing I can think of (and I'm remembering this from 2007 when I purchased the Laptop and had a wireless set up for a short while), is that the Modem and Router were bridged, which is not the case now. Do they need to be bridged for the wireless connection to work? Is it not necessary anymore and something called "Double Netting" or something like that is used...
View 1 Replies
View Related
Oct 28, 2012
Can't connect a sony vaio laptop to the internet.Says wireless association failed due to an unknown reason. My other laptop connects just fine though
View 2 Replies
View Related
Jan 7, 2012
I have just started using my D-Link 1310 Router after quite a few years of it laying around. I managed to get as far as connecting my D820 and my Desktop in a basic Network. I have Windows XP Home on both the Desktop and Laptop. The next step I want to accomplish is making the Laptop wireless with my apartment. When I first had the Router, I of course had Technical Support and my Warranty with Dell was still active, so I was walked through the process and took notes. The only file I made note of for this step was installing the driver (US) WLAN Card Rev.A12, but there must be something else that enables the WiFi catcher because I don't have any icon in the System Tray and no way to access it.
I also remember it being necessary to Bridge the Modem and Router, (I believe we did it from the Verizon site). Though I was told recently that Bridging is not used anymore, now they do a thing called "Double Netting"?
View 1 Replies
View Related
Feb 28, 2011
My company ordered NAC and ACS 1120 My question is Can i configure 802.1X security through ACS server and NAC in layer 2 Inband Virtual Gateway.for campus switches.Is it the good design to have double security for switch ports. 1st is 802.1X and 2nd is NAC in layer 2 INBAND VG?
View 1 Replies
View Related
Mar 25, 2011
I manually disabled my wireless network connection and now when I click on enable it says "connection failed"i have windows xp.
View 3 Replies
View Related
Apr 17, 2013
I am connecting the RV180 to a Huawei Echolife HG850a ONT via PPPoE, dynamic IP address from ISP.
However, error message shows:
Fri Apr 19 02:54:15 2013(UTC) [rv180][System][NONE] pppoeMultipleEnableDisable: pppoe enable failed
Fri Apr 19 02:55:16 2013(UTC) [rv180][System][NONE] pppoeMultipleEnableDisable: pppoe enable failed
I am not able to get the RV180 to logon via PPPoE and get its dynamic IP.
Firmware is version 1.0.2.6, tried resetting to factory defaults, still the same.
View 6 Replies
View Related
Dec 28, 2011
I have created a virtual WiFi hotspot in win 7 laptop with following commands. netsh wlan set hostednetwork mode=allow ssid=wii key=abcd1234 Now there is a 'Wireless Network Connection 2'(MS virtual WiFi miniport adapter) in my network connections. netsh wlan start hostednetwork WiFi hotspot started and visible in my other wifi device. But the device shows limited connectivity and i can not use internet not even local access to laptop.
My observations - I found that the IP address and DNS of WiFi miniport adapter is 192.168.11.1 But the IP assigned to my other device is 169.XXX.XX.XX which is not in same subnet
So how to set the WiFi miniport adapter of my laptop to assign proper IP address(within subnet) to my other device. So that i can get rid of LIMITED CONNECTIVITY ISSUE .
C:Userssam>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : samlaptop
[Code]......
View 2 Replies
View Related
Jan 17, 2012
I have a Dell Latitude E6410 laptop that does not have a Serial port or a Break key on the keyboard. I have a Prolific PL2303 USB-to-Serial adapter which is installed and I can access the CLI ok with this setup via HyperTerminal.
My problem is that I am unable to break into ROMMON using the break sequence Ctrl + Break (as there is no break key). I have also tried TeraTerm with the break sequence of Alt + B.
Additionally, I have tried setting the baud rate to 2600 and pressing the space bar for 10 seconds to no avail.
when I may need to break into ROMMON.
View 6 Replies
View Related
Oct 18, 2011
I recently bought one Pix 535 from ebay, it comes with software version 7.22 and I upgraded it to 8.0.4, during booting, this message always comes up: "Failed to enable checksum capability", like the following:
//output copy
------------------------------------------------------------------------------+| System BIOS Configuration, (C) 2000 General Software, Inc. |+---------------------------------------+--------------------------------------+| System CPU : Pentium III | Low Memory : 637KB || Coprocessor : Enabled | Extended Memory : 1023MB || Embedded BIOS Date : 11/28/00 | Serial Ports 1-2 : 03F8 02F8 |+---------------------------------------+--------------------------------------+
Cisco Secure PIX Firewall BIOS (4.1) #0: Tue Dec 5 17:35:26 PST 2000Platform PIX-535Flash=i28F640J5 @ 0x300
Use BREAK or ESC to interrupt flash boot.Use SPACE to begin flash boot immediately.Reading 123392 bytes of image from flash.
[code]....
I did copy startup-config from my existing Pix515E (8.0.4) to this PIX535, I did NOT pay attention if I had the same "failed to enable checksum capability" before image upgrade or startup-config change?how I can get over with it?
View 4 Replies
View Related
Sep 29, 2011
Just purchased an Asus K532-BBR9 laptop. Everything works fine, except on college campus the internet is very slow, and disconnects every few minutes.My fellow students laptops do not seem to have this problem.I figured it may be a driver issue, so I am trying to update everything.Under Network Adapters in Device Manager. The Microsoft Virtual WiFI Miniport Adapter is not up to date when I do a driver update scan.Then it says "Windows can't verify the publisher of this driver software.." with options to install anyways.
View 2 Replies
View Related
Sep 23, 2012
I'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies
View Related
Aug 8, 2007
How I enabled the Virtual Keyboard on the main portal page on our ASDM v6.0(2) ASA v8.0(2). I remember seeing the option once upon a time and now i can't seem to find it.
View 2 Replies
View Related
Feb 11, 2013
When I create a virtual switch on hyper v, i lose network connectivity and the default gateway is missing I have to manually put the default gateway in and disable and re enable the network adaptor each time the server restarts in order to get network connectivity. I am running windows server 2012 Hyper V Virtual Ethernet Adapter loses default gateway server 2012
View 9 Replies
View Related
Feb 22, 2011
I have configured 3355 NAC appliances in HA pair everything is running fine.But not able to Login through GUI (Virtual IP) which is used during the configuration of HA pair.
View 1 Replies
View Related
Jul 12, 2011
I have Gateway that runs Windows Vista. It has recently stopped connecting to my wireless router because it says the Wireless Capabilities are turned off. I have the switched turned on, I have gone into the Control Panel and Networks and made sure that everything is enabled properly. It won't let me connect at all, and my sister's laptop will connect to the router so I know that isn't the issue. Why it won't recognize my wireless adapter being on?
View 1 Replies
View Related
May 24, 2013
I got a Latitude E4310 recently, which had a dead HDD. I had to put my own drive into it and load my own copy of Windows 7 Pro onto it. Everything works, except wifi. I have tried every driver available for this model, but they just say something along the lines of the laptop not having compatible hardware. And yes, the switch on the side is on, and I have tried it in either position. In device manager, I see nothing along the lines of 'wireless card'.I even tried putting in my own mini-pci-e wifi card, an intel wifi link 5100, fully installing all drivers and software. That didn't work either - it picked it up and all the intel drivers installed but in device manager it said it 'couldn't start'.Does this model come standard with wifi? Do I have to go and buy a special dell wifi card and install that?I also have 2 Latitude E4300 laptops which I am about to put new HDDs into and set up, which I believe will have the same issue.
View 7 Replies
View Related
Mar 3, 2012
I had to system restore my laptop today and now my laptop wont connect to my wireless router. Is there a specific driver i need to install on the dell disc that come with it ? if not what all do i do ? i can only connect through wired connection
View 2 Replies
View Related
Aug 27, 2012
latitude 620 had a virus and deleted a few entries i thought were not needed. now i cant connect to internet hard wired or wireless.i dont have a system disk. below is my configuration.
Microsoft(R) Windows DOS(C)Copyright Microsoft Corp 1990-2001.
C:DOCUME~1ADMIN>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : ron Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No
[Code]...
View 18 Replies
View Related
Jan 17, 2013
my dell latitude c610 was format but my wireless is no more working
View 7 Replies
View Related
Oct 20, 2011
I can't turn on the Wifi switch (Fn + F2) and then I realized its possible it doesn't have a driver so I downloaded the Broadcom 570x Gigabit Integrated Controller so far and its still not working. Here is the what is on my device manager.
Quote:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and Settingsuser>IPCONFIG/ALL
Windows IP Configuration
Host Name . . . . . . . . . . . . : LAPTOP2
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
[code]....
View 3 Replies
View Related
Dec 6, 2012
I have a Dell Latitude D610 and my problem is that the wifi light won't come on. I've done the Fn+F2 thing and all that is enabled is bluetooth. I've gone to dell's site and updated drivers and done basically everything I've seen others do on forums. What's interesting is that once in awhile, my wifi light comes on and my wifi will work for maybe 30 seconds and then it disappears. When i go to device manager, my broadcom 802.11g adapter sometimes shows up but usually it isn't there. So it's not there with a yellow exclamation mark over it; when it is on there it's fine but it's hardly there ever. I've even removed the wireless card and reconnected it to see if it'd work but no luck.
View 1 Replies
View Related
